@inproceedings{ArrietaCastroChavesRilletal., author = {Arrieta Castro, Abel and Chaves, Rafael B. and Rill, Georg and Weber, Hans I.}, title = {Use of Integrated Control to Enhance the Safety of Vehicles in Run-Off-Road Scenarios}, series = {Proceedings of DINAME 2017 : Selected Papers of the XVII International Symposium on Dynamic Problems of Mechanics}, booktitle = {Proceedings of DINAME 2017 : Selected Papers of the XVII International Symposium on Dynamic Problems of Mechanics}, editor = {Fleury, Agenor de T. and Rade, Domingos A. and Kurka, R. G.}, edition = {1. Auflage}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-91217-2}, issn = {2195-4356}, doi = {10.1007/978-3-319-91217-2_30}, pages = {431 -- 443}, abstract = {In this work, an integrated vehicle control system (IC) is tested in run-off-road scenarios. The integrated approach was employed in order to coordinate vehicle control systems, i.e. the Anti-Lock Brake System (ABS), Four-wheel Steering (4WS) and the Electronic Stability Program (ESP). To perform a run-off-road maneuver, a fuzzy virtual test driver was designed. By receiving the lateral position of an obstacle and the vehicle's relative yaw angle, the virtual test driver is capable of following a reference trajectory. Furthermore, to test the performance of the standalone controllers, i.e. ABS, ESP and 4WS, individual maneuvers are performed using a multibody vehicle model. The vehicle without any coordination between the control systems is used as reference. For the simulation results, it is concluded that the IC improves the vehicle stability and maneuverability in comparison with the non-integrated approach.}, language = {en} } @article{Rill2017, author = {Rill, Georg}, title = {Reducing the cornering resistance by torque vectoring (X International Conference on Structural Dynamics, EURODYN 2017)}, series = {Procedia Engineering}, volume = {199}, journal = {Procedia Engineering}, publisher = {Elsevier}, doi = {10.1016/j.proeng.2017.09.393}, pages = {3284 -- 3289}, year = {2017}, abstract = {Usually, torque vectoring is used to reduce a significant understeer behavior at high speed cornering. Thus, providing larger vehicles with a sportive touch. Even on typical front wheel driven cars torque vectoring control is available now. Torque vectoring is nearly a standard on electric driven vehicles. Complex control and optimization strategies are applied to improve the maneuverability in particular or to enhance the driving behavior and reduce the energy consumption in addition. This paper shows, that a quite simple strategy will enhance the maneuverability and simultaneously reduce the cornering resistance in sharp bends. At first, a case study with a fully non-linear and three-dimensional vehicle model is performed. It turned out that a full drive torque shift to the outer wheels improves the maneuverability and reduces the cornering resistance in addition. This results are verified by an optimization performed with a simpler four-wheeled handling model. Here, the front steering angles and the driving torques at each of the four wheels are considered as free parameters. Minimizing the cornering resistance by taking the equations of motion for the four-wheeled handling model as constraints will deliver an optimal set of parameters then.}, language = {en} } @inproceedings{HacklHirschbergLexetal., author = {Hackl, Andreas and Hirschberg, W. and Lex, C. and Rill, Georg}, title = {Tyre type dependent transient force behaviour by means of a maxwell model}, series = {The Dynamics of Vehicles on Roads and Tracks : Proceedings of the 25th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2017), Rockhampton, Queensland, Australia, 14-18 August 2017}, booktitle = {The Dynamics of Vehicles on Roads and Tracks : Proceedings of the 25th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2017), Rockhampton, Queensland, Australia, 14-18 August 2017}, editor = {Spiryagin, Maksym and Gordon, Timothy and Cole, Colin and McSweeney, Tim}, publisher = {CRC Press}, address = {London}, isbn = {1351057170}, doi = {10.1201/9781315265506}, pages = {157 -- 162}, abstract = {The present papers deals with the usability of an extended Maxwell model to describe the tyre dynamics during transient driving manoeuvres. In the present article, the para-metrisation process of a dynamic tyre model is investigated in a first step, using measurement data of tyre forces from a flat trac tyre test bench, (IABG 2016). Two tyre types of dimensions 255/50 R19 and 175/55 R15 are used. The practical applicability is discussed, considering the measurement procedure and the parameter optimisation process. In a second step, the performance of the dynamic tyre model is validated using measurements of manoeuvres under higher dynamic excitation. As a last step, an outlook is given on further research planned in which the presented model and parametrisation are adapted to a larger frequency range.}, language = {en} } @inproceedings{Rill, author = {Rill, Georg}, title = {Real-Time capable Multibody Model of dual Truck Front Axles}, series = {Proceedings of DINAME 2023 - Selected Papers of the XIX International Symposium on Dynamic Problems of Mechanics, 26 Feb - 03 Mar 2023, Piren{\´o}polis, Brazil}, booktitle = {Proceedings of DINAME 2023 - Selected Papers of the XIX International Symposium on Dynamic Problems of Mechanics, 26 Feb - 03 Mar 2023, Piren{\´o}polis, Brazil}, editor = {Fleury, Agenor de T.}, publisher = {Springer}, abstract = {Dual front steering axles are quite common in multi-axled heavy duty trucks. In standard layouts of such axle combinations, the steer motions of the wheels depend not only on the rotation of the steering wheel but also on the movements of the axles. As a consequence, the model complexity of the steering system should match with the complexity of the suspension model. The development of new technologies like advanced driver assistance systems or autonomous driving can only be accomplished efficiently using extensive simulation methods. Such kind of applications demand for computationally efficient vehicle models. This paper presents a steering system model for dual front axles of heavy duty trucks which supplements the suspension model of the axles. The model takes the torsional compliance of the steering column as well as the stiffness of the tie rods and the coupling rod into account. A quasi-static solution provides a straight forward computation including the partial derivatives required for an efficient implicit solver. The steering system model matches perfectly with comparatively lean, but sufficiently accurate multibody suspension models.}, language = {en} } @techreport{MichaelSternerMareikeJentschUweHolzhammer, author = {Michael Sterner, and Mareike Jentsch, and Uwe Holzhammer,}, title = {Energiewirtschaftliche und {\"o}kologische Bewertung eines Windgas-Angebotes}, publisher = {Fraunhofer Institute for Energy Economics and Energy System Technology}, address = {Kassel}, doi = {10.13140/RG.2.2.25093.68328}, abstract = {In this technical report, (1) the benefits of the new technology for future energy supply are discussed, (2) the climate protection effect of wind gas is discussed, and (3) a reasonable use of wind energy for gas generation is analyzed. In particular, windgas in the heat market is discussed in the utilization cascade of wind energy. The new "power-to-gas" concept opens up completely new possibilities for the integration of renewable energies and for coupling the electricity and gas grids. The Sabatier process, which has been known for 100 years, was first developed for this purpose in 2008 under the leadership of the Center for Solar Energy and Hydrogen Research and Fraunhofer IWES (formerly ISET) with electrolysis to create the "power-to-gas" concept for energy storage. A first pilot plant was built by ZSW Stuttgart on behalf of SolarFuel in 2009. This plant proves the technical feasibility of the new technology. Renewable gas is stored, transported and used as required as control and reserve energy via reconversion, e.g. in combined cycle power plants. In this way, decentrally generated renewable electricity is converted into a CO2 -neutral energy carrier with high energy density. The key advantage of renewable methane is the use of existing infrastructure such as gas grids, gas storage and end-use equipment for the integration of renewable energy. Technologies for natural gas are state of the art and commercially available. Methane also has three times the energy density of hydrogen.}, language = {en} } @techreport{ZacherlWopperMieslingeretal., author = {Zacherl, Florian and Wopper, Christoph and Mieslinger, Johann and Peis, Michael and Rabl, Hans-Peter}, title = {Schlussbericht zum Verbundvorhaben NAMOSYN: Nachhaltige Mobilit{\"a}t durch synthetische Kraftstoffe}, address = {Regensburg}, pages = {156}, abstract = {Im Labor f{\"u}r Verbrennungsmotoren und Abgasnachbehandlung der OTH-Regensburg sollten im Zuge des NAMOSYN-Projektes zwei Vertreter klimaneutraler Kraftstoffe an verschiedenen Systempr{\"u}fst{\"a}nden (Motor-, Einspritzpr{\"u}fstand, optisch zug{\"a}ngliche Einspritzkammer, …) und mit Hilfe von Simulationsmethoden f{\"u}r den Einsatz in bestehenden Verbrennungsmotoren untersucht werden. Synthetische Kraftstoffe aus der Gruppe der Oxymethylenether (OME) stellen eine CO2-neutrale Alternative zu fossilem Dieselkraftstoff dar. F{\"u}r Ottomotoren wurde untersucht, ob der synthetische Kraftstoff DMC/MeFo (Dimethylcarbonat \& Methylformiat) einen Ersatz f{\"u}r Ottokraftstoff darstellen kann, bzw. eine Drop-In-F{\"a}higkeit gegeben ist. Die OTH Regensburg bearbeitete 2 unabh{\"a}ngige Teilvorhaben zur motorischen Testung von synthetischen Kraftstoffen: „FC 1A: Motorische Testung von OME" und „FC 2: Untersuchung von C1-Oxygenaten f{\"u}r Ottomotoren". Die Projektlaufzeit betrug 3,5 Jahre, inkl. kostenneutraler Verl{\"a}ngerung um 6 Monate aufgrund der Corona-Pandemie. Im FC1A "AP2-Nachr{\"u}stung Dieselmotoren" der OTH Regensburg lag der Fokus auf der Erforschung der Potentiale und der Umr{\"u}stung eines Einzylinder-Dieselmotors mit Pumpe-Leitung-D{\"u}se-(PLD)-Einspritzsystem des Projektpartners Motorenfabrik Hatz GmbH und Co. KG f{\"u}r OME-Betrieb. Im AP2.1 wurden umfangreiche Daten gesammelt und Simulationsmodelle des Motors und PLD-Einspritzsystems erstellt und mit Dieselkraftstoff und OME validiert. Nachfolgend wurden Parameterstudien zur Geometrie des Einspritzsystems und der physikalischen Eigenschaften von OME durchgef{\"u}hrt. In AP2.2 und AP2.3 wurden umfangreiche Untersuchungen an einem Motor- und Einspritzsystempr{\"u}fstand mit Diesel und OME durchgef{\"u}hrt und der Steuerger{\"a}tedatensatz f{\"u}r den OME-Betrieb optimiert. Die Ergebnisse zeigen, dass die Umstellung des Kraftstoffs auf OME, insbesondere bei einfachen Motoren mit rudiment{\"a}rer Einspritztechnik und ohne Mittel zur NOx-Reduzierung (keine AGR oder SCR), ein enormes Potenzial zur Steigerung des Wirkungsgrads bei gleichzeitiger Reduzierung aller regulierten Schadstoffe (NOx, 𝑃N, 𝑃M, CO und 𝑉OC) er{\"o}ffnet. Die Ergebnisse und generierten Simulationsmodelle unterst{\"u}tzen eine schnelle Serienentwicklung und Einf{\"u}hrung von OME-Umr{\"u}stl{\"o}sungen. In FC 2 werden die vielversprechenden Kraftstoffe Methylformiat (MeFo) und Dimethylcarbonat (DMC) motorisch getestet. Untersuchungen am Kraftstoffsystem und wichtigen Komponenten dienen als Grundlage f{\"u}r das AP3. Im AP3 wird die Machbarkeit der DMC/MeFo-Verbrennung am Vollmotor demonstriert und die erwarteten Emissionsvorteile gegen{\"u}ber herk{\"o}mmlichen Ottokraftstoffen gezeigt. Abweichend von der urspr{\"u}nglichen Planung werden an der OTH Regensburg Kraftstoffblends aus Benzin und MeFo untersucht, um den Einsatzbereich des Kraftstoffs zu erweitern. In AP5 werden potentielle Mischungsverh{\"a}ltnisse analysiert und die Eigenschaften der ausgew{\"a}hlten Kraftstoffmischungen an einem Einspritzratenpr{\"u}fstand, an der Einspritzkammer und am Vollmotor untersucht. Es werden Einspritzverhalten, Gemischaufbereitung und Abgasemissionen bewertet. Zudem wird eine Kraftstoffmischanlage entwickelt und ein optischer Zugang am Vollmotor erm{\"o}glicht. Eine {\"O}lverd{\"u}nnungsmesstechnik wird eingesetzt, um den Kraftstoffeintrag ins Motor{\"o}l zu untersuchen}, language = {de} } @article{SchuemannMorichKaufholdetal., author = {Sch{\"u}mann, Malte and Morich, J. and Kaufhold, T. and B{\"o}hm, Valter and Zimmermann, Klaus and Odenbach, Stefan}, title = {A mechanical characterisation on multiple timescales of electroconductive magnetorheological elastomers}, series = {Magnetism and Magnetic Materials}, volume = {453}, journal = {Magnetism and Magnetic Materials}, number = {May}, publisher = {Elsevier}, doi = {10.1016/j.jmmm.2018.01.029}, pages = {198 -- 205}, abstract = {Magnetorheological elastomers are a type of smart hybrid material which combines elastic properties of a soft elastomer matrix with magnetic properties of magnetic micro particles. This leads to a material with magnetically controllable mechanical properties of which the magnetorheological effect is the best known. The addition of electroconductive particles to the polymer mix adds electrical properties to the material behaviour. The resulting electrical resistance of the sample can be manipulated by external magnetic fields and mechanical loads. This results in a distinct interplay of mechanical, electrical and magnetic effects with a highly complex time behaviour. In this paper a mechanical characterisation on multiple time scales was conducted to get an insight on the short and long-term electrical and mechanical behaviour of this novel material. The results show a complex resistivity behaviour on several timescales, sensitive to magnetic fields and strain velocity. The observed material exhibits fatigue and relaxation behaviour, whereas the magnetorheological effect appears not to interfere with the piezoresistive properties.}, language = {en} } @inproceedings{KetterlHeinrichReitmeieretal., author = {Ketterl, Hermann and Heinrich, Tobias and Reitmeier, Torsten and Hoelscher, Clemens}, title = {Emissionsabh{\"a}ngige Leistungsregelung f{\"u}r BHKW's}, series = {Tagungsband AALE 2020: Automatisierung und Mensch-Technik-Interaktion, 17. Fachkonferenz, 4. bis 6. M{\"a}rz 2020, Leipzig}, volume = {2020}, booktitle = {Tagungsband AALE 2020: Automatisierung und Mensch-Technik-Interaktion, 17. Fachkonferenz, 4. bis 6. M{\"a}rz 2020, Leipzig}, editor = {J{\"a}kel, Jens and Thiel, Robert}, publisher = {VDE-Verlag}, isbn = {978-3-8007-5180-8}, pages = {7}, language = {de} } @misc{OPUS4-6542, title = {Energieforschung}, edition = {Ausgabe 2023}, publisher = {OTH Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg / Regensburg Center of Energy and Resources (RCER)}, doi = {10.35096/othr/pub-6542}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-65422}, abstract = {{\"U}ber uns Das Regensburg Center of Energy and Resources (RCER) b{\"u}ndelt seit 2012 die Aktivit{\"a}ten der Ostbayerischen Technischen Hochschule Regensburg (OTH Regensburg) und der regionalen Wirtschaftsunternehmen auf dem Strategiefeld „Energie und Ressourcen". Mission: Energieforschung: vernetzen, voranbringen, vermitteln Das RCER f{\"o}rdert die Vernetzung verschiedener Disziplinen der Energieforschung innerhalb der OTH Regensburg und mit externen Partnern (Firmen, F{\"o}rdertr{\"a}gern, Forschungsinstitutionen, {\"o}ffentlichen Einrichtungen). Das RCER ist Ihr Partner beim Voranbringen von Kooperationen und Forschungsvorhaben durch Unterst{\"u}tzung in der Antragsphase, bei der Einwerbung von Projektmitteln und Projektbegleitung im Energiebereich. Das RCER steht f{\"u}r die Vermittlung von Know-how, Basiswissen, aktuellen Fragen und den Technologietransfer rund um das Thema Energie zwischen Wissenschaft, Wirtschaft, Gesellschaft und Politik. Vision Wir sind Ihr erster Ansprechpartner und Motor f{\"u}r innovative Energieforschung. Werte Verl{\"a}sslichkeit, Kompetenz, Verantwortungsbewusstsein.Regional verwurzelt und weltoffen}, language = {de} } @misc{Sterner, author = {Sterner, Michael}, title = {Strom - W{\"a}rme - Verkehr - Industrie: das Zusammenspiel der Sektoren {\"u}ber Power-to-X}, series = {Deutscher Ingenieurtag 2021, D{\"u}sseldorf 20. Mai 2021}, journal = {Deutscher Ingenieurtag 2021, D{\"u}sseldorf 20. Mai 2021}, publisher = {VDI-Verlag}, language = {de} } @article{MikhaeilGadererDawoud, author = {Mikhaeil, Makram and Gaderer, Matthias and Dawoud, Belal}, title = {On the application of adsorber plate heat exchangers in thermally driven chillers}, series = {Applied Thermal Engineering}, volume = {220}, journal = {Applied Thermal Engineering}, publisher = {Elsevier}, doi = {10.1016/j.applthermaleng.2022.119713}, abstract = {The effect of both heat and mass transfer characteristic lengths (HTCL, MTCL) of two different adsorber plate heat exchangers (APHE), for application in an adsorption chiller, on the adsorption and desorption kinetics is investigated. Three representative test frames (TF1-TF3) are prepared to examine small-scale adsorbent samples of the microporous silica gel (Siogel of Oker-Chemie, Germany) applying the volumetric large-temperature-jump methodology at different operating conditions. Based on the obtained kinetic data, an analytical model has been developed to predict the specific cooling power (SCP) and the coefficient of performance (COP) of a single-bed adsorption chiller comprising the studied APHEs. It turned out that, within the tested range of HTCL and MTCL, it can be concluded that, the adsorption kinetics are mainly influenced by the MTCL, while the desorption kinetics are dominated by the HTCL of the adsorbent domain. Applying Siogel as loose pellets inside a newly introduced APHE results in of 423.3 and 182.7 W⋅kg-1, at the evaporator temperatures of 15 °C and 5 °C, respectively. Herein, the condenser and adsorber-end temperatures amount to 30 °C and the desorption-end temperature to 90 °C. The corresponding s amount to 0.50 and 0.40, respectively, which represent quite promising results for further design optimizations.}, language = {en} } @article{FrazzicaPalombaDawoud, author = {Frazzica, Andrea and Palomba, Valeria and Dawoud, Belal}, title = {Thermodynamic Performance of Adsorption Working Pairs for Low-Temperature Waste Heat Upgrading in Industrial Applications}, series = {Applied Sciences}, volume = {11}, journal = {Applied Sciences}, number = {8}, publisher = {MDPI}, doi = {10.3390/app11083389}, abstract = {The present work aims at the thermodynamic analysis of different working pairs in adsorption heat transformers (AdHT) for low-temperature waste heat upgrade in industrial processes. Two different AdHT configurations have been simulated, namely with and without heat recovery between the adsorbent beds. Ten working pairs, employing different adsorbent materials and four different refrigerants, have been compared at varying working boundary conditions. The effects of heat recovery and the presence of a temperature gradient for heat transfer between sinks/sources and the AdHT components have been analyzed. The achieved results demonstrate the possibility of increasing the overall performance when internal heat recovery is implemented. They also highlight the relevant role played by the existing temperature gradient between heat transfer fluids and components, that strongly affect the real operating cycle of the AdHT and thus its expected performance. Both extremely low, i.e., 40-50 degrees C, and low (i.e., 80 degrees C) waste heat source temperatures were investigated at variable ambient temperatures, evaluating the achievable COP and specific energy. The main results demonstrate that optimal performance can be achieved when 40-50 K of temperature difference between waste heat source and ambient temperature are guaranteed. Furthermore, composite sorbents demonstrated to be the most promising adsorbent materials for this application, given their high sorption capacity compared to pure adsorbents, which is reflected in much higher achievable specific energy.}, language = {en} } @article{ThemaWeidlichKauletal., author = {Thema, Martin and Weidlich, Tobias and Kaul, Anja and B{\"o}llmann, Andrea and Huber, Harald and Bellack, Annett and Karl, J{\"u}rgen and Sterner, Michael}, title = {Optimized biological CO2-methanation with a pure culture of thermophilic methanogenic archaea in a trickle-bed reactor}, series = {Bioresource Technology}, journal = {Bioresource Technology}, number = {333}, publisher = {Elsevier}, doi = {10.1016/j.biortech.2021.125135}, abstract = {In this study, a fully automated process converting hydrogen and carbon dioxide to methane in a high temperature trickle-bed reactor was developed from lab scale to field test level. The reactor design and system performance was optimized to yield high methane content in the product gas for direct feed-in to the gas grid. The reaction was catalyzed by a pure culture of Methanothermobacter thermoautotrophicus IM5, which formed a biofilm on ceramic packing elements. During 600 h in continuous and semi-continuous operation in countercurrent flow, the 0.05 m3 reactor produced up to 95.3 \% of methane at a methane production rate of 0.35 mCH43mR-3h-1. Adding nitrogen as carrier gas during startup, foam control and dosing of ammonium and sodium sulfide as nitrogen and sulfur source were important factors for process automation.}, language = {en} } @article{GaertnerRankHeberletal., author = {G{\"a}rtner, Sebastian and Rank, Daniel and Heberl, Michael and Gaderer, Matthias and Dawoud, Belal and Haumer, Anton and Sterner, Michael}, title = {Simulation and Techno-Economic Analysis of a Power-to-Hydrogen Process for Oxyfuel Glass Melting}, series = {Energies}, volume = {14}, journal = {Energies}, number = {24}, publisher = {MDPI}, doi = {10.3390/en14248603}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-22713}, abstract = {As an energy-intensive industry sector, the glass industry is strongly affected by the increasingly stringent climate protection targets. As established combustion-based production systems ensure high process stability and glass quality, an immediate switch to low greenhouse gas emission processes is difficult. To approach these challenges, this work investigates a step-by-step integration of a Power-to-Hydrogen concept into established oxyfuel glass melting processes using a simulation approach. This is complemented by a case study for economic analysis on a selected German glass industry site by simulating the power production of a nearby renewable energy park and subsequent optimization of the power-to-hydrogen plant performance and capacities. The results of this study indicate, that the proposed system can reduce specific carbon dioxide emissions by up to 60\%, while increasing specific energy demand by a maximum of 25\%. Investigations of the impact of altered combustion and furnace properties like adiabatic flame temperature (+25 °C), temperature efficiency (∆ξ = -0.003) and heat capacity flow ratio (∆zHL = -0.009) indicate that pure hydrogen-oxygen combustion has less impact on melting properties than assumed so far. Within the case study, high CO2 abatement costs of 295 €/t CO2-eq. were determined. This is mainly due to the insufficient performance of renewable energy sources. The correlations between process scaling and economic parameters presented in this study show promising potential for further economic optimization of the proposed energy system in the future.}, language = {en} } @article{SchorrZentnerZimmermannetal., author = {Schorr, Philipp and Zentner, Lena and Zimmermann, Klaus and B{\"o}hm, Valter}, title = {Jumping locomotion system based on a multistable tensegrity structure}, series = {Mechanical systems and signal processing}, journal = {Mechanical systems and signal processing}, number = {152}, publisher = {Elsevier}, doi = {10.1016/j.ymssp.2020.107384}, abstract = {All known locomotion principles are limited respective to environmental conditions. Often, the occurrence of obstacles or gaps means the break-off for the operating motion systems. For such circumstances, a controllable jumping locomotion is required to cross these barriers. However, this locomotion demands sophisticated requirements to the actuation. The abrupt actuation is commonly realized by high dynamic actuators or complex mechanisms. In this work, a simple solution utilizing the multistability of a compliant tensegrity structure is described. Therefore, a two-dimensional tensegrity structure featuring four stable equilibria is considered. Based on bifurcation analyses a feasible actuation to control the current equilibrium configuration is derived. Changing between selected equilibrium states enables a great difference in potential energy, which yields a jumping motion of the structure. Based on numerical simulations a suitable actuation strategy is chosen to overcome obstacle and steps by jumping forward or backward, respectively. The theoretical approach is examined experimentally with a prototype of the multistable tensegrity structure. (c) 2020 Elsevier Ltd. All rights reserved. All known locomotion principles are limited respective to environmental conditions. Often, the occurrence of obstacles or gaps means the break-off for the operating motion systems. For such circumstances, a controllable jumping locomotion is required to cross these barriers. However, this locomotion demands sophisticated requirements to the actuation. The abrupt actuation is commonly realized by high dynamic actuators or complex mechanisms. In this work, a simple solution utilizing the multistability of a compliant tensegrity structure is described. Therefore, a two-dimensional tensegrity structure featuring four stable equilibria is considered. Based on bifurcation analyses a feasible actuation to control the current equilibrium configuration is derived. Changing between selected equilibrium states enables a great difference in potential energy, which yields a jumping motion of the structure. Based on numerical simulations a suitable actuation strategy is chosen to overcome obstacle and steps by jumping forward or backward, respectively. The theoretical approach is examined experimentally with a prototype of the multistable tensegrity structure.}, language = {en} } @article{EmbergerAltmannGebhardetal., author = {Emberger, Peter and Altmann, Robert and Gebhard, J{\"u}rgen and Thuneke, Klaus and Winkler, Markus and T{\"o}pfer, Georg and Rabl, Hans-Peter and Remmele, Edgar}, title = {Combustion characteristics of pure rapeseed oil fuel after injection in a constant volume combustion chamber with a non-road mobile machinery engine solenoid injector}, series = {Fuel}, journal = {Fuel}, number = {320}, publisher = {Elsevier}, doi = {10.1016/j.fuel.2022.123979}, abstract = {Pure rapeseed oil fuel (R100) according to standard DIN 51605 is a greenhouse gas saving option for the mobility sector. With its high energy density close to diesel fuel, R100 is suitable to operate non-road mobile machinery with a high power demand and long operating time, where electric drives reach their limits. Advantages are indicated for its use in environmentally sensitive areas like agriculture since R100 is highly biodegradable and non-toxic. However, R100 is characterised by differing physical and chemical properties compared to diesel. The objective of the research is to investigate the differences in the ignition and combustion behaviour of R100 compared to diesel fuel (DF). For this purpose, a constant volume combustion chamber is used, which is equipped with a modern solenoid injector for engines of non-road mobile machinery. The researched injector shows a different hydraulic behaviour when using R100 compared to DF in that the injected fuel mass is lower with R100 than with DF. In combination with the 14 \% by mass lower calorific value, less energy output is determined with R100. When varying the injection pressure, the impact on the ignition delay and combustion behaviour is much higher for R100 than for DF. Specifically, an increase of the injection pressure supports mixture preparation and thus partially compensates the differing physical properties of R100. The results of ignition delay measurements and net heat release analysis are as follows: At low load conditions with low injection pressure as well as a low combustion chamber temperature and pressure, R100 ignites later and shows a further delayed combustion compared to diesel. The opposite is observed for medium and high load conditions, where R100 ignites faster and without delayed combustion in comparison to DF. Thus, an adjustment of the heat release of R100 at the same level as for DF is possible by modifying the injection strategy. The research shows that for an optimised combustion of R100 the injection settings must be adjusted for every operation point separately. The results indicate how the injection parameters should be adjusted for different load conditions to realise a high-quality engine calibration for R100.}, language = {en} } @inproceedings{TremmelNaglerKutteretal., author = {Tremmel, Florian and Nagler, O. and Kutter, C. and Holmer, Rainer}, title = {Smart Cantilever Probe with Integrated Force and Acoustic Emission Sensor}, series = {2023 IEEE SENSORS, Vienna, Austria, 10/29/2023 - 11/1/2023}, booktitle = {2023 IEEE SENSORS, Vienna, Austria, 10/29/2023 - 11/1/2023}, publisher = {IEEE}, isbn = {979-8-3503-0387-2}, doi = {10.1109/SENSORS56945.2023.10325021}, pages = {1 -- 4}, abstract = {Acoustic emission (AE) testing recently found its application in the wafer testing sector of the semiconductor industry. To find out the mechanical robustness of semiconductor devices, contact pads on the chip surface are intentionally overstressed with an indenter tip and the appearing oxide cracks are detected with help of the generated AE signals. This is done in a customized test bench with a patented sensor-indenter system. This paper presents an improved version of the measurement setup that solves certain disadvantages of it and can be used in a standard wafer prober. The main components of the developed sensor system are a strain gauge for contact force measurement and a piezoelectric sensor element for AE signal detection. Both components are integrated on a cantilever beam which has an exchangeable indenter tip at its free end. The cantilever probe is electrically conductive to enable electrical tests via the indenter tip. This smart sensor-cantilever combination (SCC) can be mounted with several adapter components on a carrier plate to place it in a wafer prober. For both sensor elements amplifier circuits are developed to enhance their signal-to-noise ratios (SNRs). A prototype setup is shown together with simulated and experimental results to demonstrate its performance. The mechanical properties of the cantilever, as well as the force sensor and the AE crack signals, already fulfill the requirements for an implementation in a wafer prober. To further improve the sensor resolutions and detection limits, several optimizations regarding the design of the SCC are in progress.}, language = {en} } @article{ThemaBauerSterner, author = {Thema, Martin and Bauer, Franz and Sterner, Michael}, title = {Power-to-Gas: Electrolysis and methanation status review}, series = {Renewable and Sustainable Energy Reviews}, volume = {112}, journal = {Renewable and Sustainable Energy Reviews}, number = {7}, publisher = {Elsevier}, doi = {10.1016/j.rser.2019.06.030}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-26238}, pages = {775 -- 787}, abstract = {This review gives a worldwide overview on Power-to-Gas projects producing hydrogen or renewable substitute natural gas focusing projects in central Europe. It deepens and completes the content of previous reviews by including hitherto unreviewed projects and by combining project names with details such as plant location. It is based on data from 153 completed, recent and planned projects since 1988 which were evaluated with regards to plant allocation, installed power development, plant size, shares and amounts of hydrogen or substitute natural gas producing examinations and product utilization phases. Cost development for electrolysis and carbon dioxide methanation was analyzed and a projection until 2030 is given with an outlook to 2050. The results show substantial cost reductions for electrolysis as well as for methanation during the recent years and a further price decline to less than 500 euro per kilowatt electric power input for both technologies until 2050 is estimated if cost projection follows the current trend. Most of the projects examined are located in Germany, Denmark, the United States of America and Canada. Following an exponential global trend to increase installed power, today's Power-to-Gas applications are operated at about 39 megawatt. Hydrogen and substitute natural gas were investigated on equal terms concerning the number of projects.}, language = {en} } @article{MonkmanSindersbergerPrem, author = {Monkman, Gareth J. and Sindersberger, Dirk and Prem, Nina}, title = {Magnetically enhanced photoconductive high voltage control}, series = {ISSS Journal of Micro and Smart Systems}, volume = {11}, journal = {ISSS Journal of Micro and Smart Systems}, publisher = {Springer Nature}, doi = {10.1007/s41683-021-00088-z}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-30606}, pages = {317 -- 328}, abstract = {The recent surge of interest in electrostatic actuators, particularly for soft robotic applications, has placed increasing demands on high voltage control technology. In this respect, optoelectronic bidirectional switching and analogue regulation of high voltages is becoming increasingly important. One common problem is the leakage current due to dark resistance of the material or device used. Another is the physical size of such elements. However, their ability to provide galvanic separation makes them a very attractive alternative to conventional (wired) semiconductor elements. This paper gives an overview of available methods and devices before introducing a concept based on the combination of photoresistive and magnetoresistive effects in Gallium Arsenide that are potentially applicable to other semiconductor materials.}, language = {en} } @article{HaugVetter, author = {Haug, Sonja and Vetter, Miriam}, title = {Altersgerechtes Wohnen im Quartier}, series = {Standort - Zeitschrift f{\"u}r angewandte Geographie}, volume = {45}, journal = {Standort - Zeitschrift f{\"u}r angewandte Geographie}, publisher = {Springer Nature}, issn = {1432-220X}, doi = {10.1007/s00548-020-00678-3}, pages = {11 -- 17}, abstract = {Im Alter nimmt das Quartier aufgrund geringerer Aktionsradien an Bedeutung zu. Der Beitrag befasst sich mit der Frage, welche Besonderheiten sich bei Senioren-Haushalten im Hinblick auf Wohnen und soziale Teilhabe zeigen. Aus dem Projekt MAGGIE werden Ergebnisse einer schriftlichen Haushaltsbefragung (N=195) in der Wohngenossenschaft Margaretenau Regensburg dargestellt. Hierbei wird auf die aktuelle und zuk{\"u}nftige Wohnsituation, den Ver{\"a}nderungsbedarf, den Wunsch nach Gemeinschaftsangeboten und die soziale Einbettung eingegangen. Es zeigt sich eine geringe Ver{\"a}nderungsbereitschaft und ein {\"u}berdurchschnittlich hohes Maß an lokalem Sozialkapital. Am Ende werden Schlussfolgerungen f{\"u}r das Sanierungs- und Quartiersmanagement gezogen.}, subject = {Alter}, language = {de} }