@inproceedings{BuenteRillRuggaberetal., author = {B{\"u}nte, Tilman and Rill, Georg and Ruggaber, Julian and Tobol{\´a}ř, Jakub}, title = {Modelling and Validation of the TMeasy Tyre Model for Extreme Parking Manoeuvres}, series = {Advances in Dynamics of Vehicles on Roads and Tracks II, Proceedings of the 27th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2021): August 17-19, 2021, Saint Petersburg, Russia}, booktitle = {Advances in Dynamics of Vehicles on Roads and Tracks II, Proceedings of the 27th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2021): August 17-19, 2021, Saint Petersburg, Russia}, editor = {Orlova, Anna and Cole, David}, publisher = {Springer}, address = {Cham}, isbn = {978-3-031-07305-2}, doi = {10.1007/978-3-031-07305-2_94}, pages = {1015 -- 1025}, abstract = {The TMeasy is a tyre model suitable for vehicle handling analyses and enables easy parametrisation. Recently, a convenient interface to Modelica was implemented by DLR to support the TMeasy also for vehicle modelling in multi-physical domains. This paper focuses especially on the particular problem of reliable reproduction of the tyre's bore torque which occurs during parking manoeuvres. It outlines the theory behind it, discusses the Modelica interface implementation, and presents the results of parameter identification which were achieved based on real experiments with DLR's research platform ROboMObil.}, language = {en} } @inproceedings{Rill, author = {Rill, Georg}, title = {A Three-Dimensional and Nonlinear Virtual Test Car}, series = {ENOC 2022, book of abstracts, 10th European Nonlinear Dynamics Conference: July 17-22, 2022, Lyon, France}, booktitle = {ENOC 2022, book of abstracts, 10th European Nonlinear Dynamics Conference: July 17-22, 2022, Lyon, France}, address = {Lyon}, pages = {49 -- 58}, abstract = {Virtual testing procedures have become a standard in vehicle dynamics. The increasing complexity of driver assistance sys- tems demand for more and more virtual tests, which are supposed to produce reliable results even in the limit range. As a consequence, simplified vehicle models, like the classical bicycle model or 4-wheel vehicle models, have to be replaced by a fully three-dimensional and nonlinear vehicle model, which also encompasses the details of the suspension systems. This paper presents a passenger car model, where the chassis, the four knuckles, and the four wheels are described by rigid bodies, the suspension system is modeled by the generic design kinematics, and the TMeasy tire model provides the tire forces and torques in all driving situations.}, language = {en} } @inproceedings{RillButzRill, author = {Rill, Daniel and Butz, Christiane and Rill, Georg}, title = {Dynamic Interaction of Heavy Duty Vehicles and Expansion Joints}, series = {Multibody Dynamics 2019, Proceedings of the 9th ECCOMAS Thematic Conference on Multibody Dynamics}, volume = {53}, booktitle = {Multibody Dynamics 2019, Proceedings of the 9th ECCOMAS Thematic Conference on Multibody Dynamics}, editor = {Kecskem{\´e}thy, Andr{\´e}s and Geu Flores, Francisco}, publisher = {Springer International Publishing}, address = {Cham}, isbn = {978-3-030-23131-6}, doi = {10.1007/978-3-030-23132-3_56}, pages = {471 -- 478}, abstract = {The "Smart Bridge (Intelligente Br{\"u}cke)" project cluster, initiated by the German Federal Highway Research Institute (Bundesanstalt f{\"u}r Straßenwesen, BASt) and the Federal Ministry of Transport and Digital Infrastructure (BMVI), focuses on "smart" monitoring devices that allow an efficient and economic maintenance management of bridge infrastructures. Among the participating projects, the one presented herein focuses on the development of a smart expansion joint, to assess the traffic parameters on site. This is achieved by measuring velocity and weight of crossing vehicles. In reference measurements, performed with a three-axle truck and a typical tractor semi-trailer combination with five axles in total, it was shown that the interaction between the vehicle and the expansion joint is highly dynamic and depends on several factors. To get more insight into this dynamic problem, a virtual test rig was set up. Although nearly all vehicle parameters had to be estimated, the simulation results conform very well with the measurements and are robust to vehicle parameter variations. In addition, they indicate a significant influence of the expansion joint dynamic to the peak values of the measured wheel loads, in particular on higher driving velocities. By compensating the relevant dynamic effects in the measurements, a "smart" data processing algorithm makes it possible to determine the actual vehicle weights in random traffic with reliability and appropriate accuracy.}, language = {en} } @inproceedings{RillArrietaCastro, author = {Rill, Georg and Arrieta Castro, Abel}, title = {A Novel Approach for Parametrization of Suspension Kinematics}, series = {Advances in Dynamics of Vehicles on Roads and Tracks: Proceedings of the 26th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2019), August 12-16, 2019, Gothenburg, Sweden}, booktitle = {Advances in Dynamics of Vehicles on Roads and Tracks: Proceedings of the 26th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2019), August 12-16, 2019, Gothenburg, Sweden}, editor = {Klomp, Matthijs and Bruzelius, Fredrik and Nielsen, Jens and Hillemyr, Angela}, publisher = {Springer International Publishing}, address = {Cham}, isbn = {978-3-030-38076-2}, doi = {10.1007/978-3-030-38077-9_210}, pages = {1848 -- 1857}, abstract = {n the automotive industry, simulations are needed to analyse the dynamics of vehicles and also of its main components and subsystems, e.g. tires, brakes and suspension systems. These simulations are required for an early-stage development and in consequence, they must deliver realistic results. Suspension systems plays a key role in comfort and safety of road vehicles. They usually consist of rigid links and force elements that are arranged with a specific topology. In addition, some of their functionalities are to carry the weight of the car and the passengers, and maintain a correct wheel alignment. In simulations involving suspension systems, lookup-tables are frequently used. They are obtained from a Kinematic and Compliance (KnC) test and then standardized for a specific vehicle simulation software. Nonetheless, lookup-tables require a reasonable number of characteristic points. Additionally, derivatives, interpolation, and extrapolation are not necessarily smooth. This produces results that depend on the interpolation technique and may be inaccurate. In this paper, a novel method called "design kinematics" is proposed. This method can describe the kinematic properties of almost any type of suspension systems. Comparisons with an analytic calculation and a KnC measurement shown that the design kinematics is able to represent the kinematic and compliance properties of suspension systems extremely well and very efficiently.}, language = {en} } @article{Rill, author = {Rill, Georg}, title = {Sophisticated but quite simple contact calculation for handling tire models}, series = {Multibody system dynamics}, volume = {45}, journal = {Multibody system dynamics}, number = {2}, publisher = {Springer Nature}, organization = {SPRINGER}, doi = {10.1007/s11044-018-9629-4}, pages = {131 -- 153}, abstract = {Handling tire models like Pacejka (Tire and Vehicle Dynamics, 3rd edn., Elsevier, Amsterdam, 2012) or TMeasy (Rill in Proc. of the XV Int. Symp. on Dynamic Problems of Mechanics, Buzios, RJ, Brazil, 2013) consider the contact patch as one coherent plane. As a consequence, the irregularities of a rough road profile must be approximated by an appropriate local road plane that serves as an effective road plane in order to calculate the geometric contact point and the corresponding contact velocities. The Pacejka/SWIFT tire model employs a road enveloping model that generates the effective height and slope by elliptical cams. TMeasy just uses four representative road points for that purpose. In addition, TMeasy replaces the geometric contact point by the static contact point and shifts it finally to the dynamic contact point that represents the point where the contact forces are applied. In doing so, a rather sophisticated but still simple contact calculation is possible. Simulations obtained with a virtual tire test rig and fully nonlinear three-dimensional multibody system models of a motor-scooter and a passenger car demonstrate the potential of this contact approach.}, language = {en} } @inproceedings{RillArrietaCastro, author = {Rill, Georg and Arrieta Castro, Abel}, title = {The Influence of Axle Kinematics on Vehicle Dynamics}, series = {Interdisciplinary Applications of Kinematics. Proceedings of the Third International Conference (IAK)}, volume = {71}, booktitle = {Interdisciplinary Applications of Kinematics. Proceedings of the Third International Conference (IAK)}, editor = {Kecskem{\´e}thy, Andr{\´e}s and Geu Flores, Francisco and Carrera, Eliodoro and Elias, Dante A.}, publisher = {Springer International Publishing}, address = {Cham}, isbn = {978-3-030-16422-5}, doi = {10.1007/978-3-030-16423-2_2}, pages = {23 -- 31}, abstract = {The automotive industry employs many different kinds of axle suspension systems at modern passenger cars. Important criteria are costs, space requirements, kinematic properties, and compliance attributes. This paper illustrates that in particular the kinematic properties of a suspension system have a significant influence on the dynamics of vehicles. As a consequence, the kinematics of a suspension system must be modeled very precisely and nonlinear. Typical kinematical features of a suspension system are discussed by analyzing the most common double wishbone axle suspension system. The influence of the axle kinematics on vehicle dynamics is finally demonstrated by simulation results generated with a fully nonlinear and three-dimensional multibody vehicle model.}, language = {en} } @inproceedings{Rill, author = {Rill, Georg}, title = {TMeasy 6.0-A handling tire model that incorporates the first two belt eigenmodes}, series = {Proceedings of the XI International Conference on Structural Dynamics (EURODYN 2020): Athens, Greece, 23.11.2020 - 26.11.2020}, booktitle = {Proceedings of the XI International Conference on Structural Dynamics (EURODYN 2020): Athens, Greece, 23.11.2020 - 26.11.2020}, publisher = {EASD Procedia}, doi = {10.47964/1120.9054.18673}, pages = {676 -- 689}, abstract = {TMeasy 6.0, an extension to the standard TMeasy tire model of version 5.3, takes the relevant first two rigid body eigenmodes of the belt into consideration. These modes represent the in plane longitudinal and rotational movements of the belt relative to the rim. The dynamics of the longitudinal force is of higher order then and reproduces the tire wheel vibrations, required for indirect tire-pressure monitoring systems (iTPMS), sufficiently well. A tailored implicit solver, which takes the stiff coupling between the longitudinal force and the belt motions into account, still provides real-time performance in addition. Simulation examples show that a rigid body vehicle model equipped with TMeasy 6.0 makes it possible to investigate second generation indirect tire-pressure monitoring systems.}, language = {en} } @book{RillArrietaCastro, author = {Rill, Georg and Arrieta Castro, Abel}, title = {Road Vehicle Dynamics}, publisher = {CRC Press}, address = {Boca Raton, Fla.}, isbn = {9780429244476}, doi = {10.1201/9780429244476}, abstract = {Road Vehicle Dynamics: Fundamentals and Modeling with MATLAB®, Second Edition combines coverage of vehicle dynamics concepts with MATLAB v9.4 programming routines and results, along with examples and numerous chapter exercises. Improved and updated, the revised text offers new coverage of active safety systems, rear wheel steering, race car suspension systems, airsprings, four-wheel drive, mechatronics, and other topics. Based on the lead author's extensive lectures, classes, and research activities, this unique text provides readers with insights into the computer-based modeling of automobiles and other ground vehicles. Instructor resources, including problem solutions, are available from the publisher.}, subject = {Fahrdynamik}, language = {en} } @incollection{Rill, author = {Rill, Georg}, title = {Multibody Systems and Simulation Techniques}, series = {Vehicle Dynamics of Modern Passenger Cars}, booktitle = {Vehicle Dynamics of Modern Passenger Cars}, editor = {Lugner, Peter}, publisher = {Springer International Publishing}, address = {Cham}, isbn = {978-3-319-79007-7}, doi = {10.1007/978-3-319-79008-4_6}, pages = {309 -- 375}, abstract = {This part begins with an introduction to Multibody Systems (MBS). It presents the elements of MBS and discusses different modeling aspects. Then, different methods to generate the equations of motion are presented. Solvers for ordinary differential equations (ODE) as well as differential algebraic equations (DAE) are discussed. Finally, techniques for "online" and "offline" simulations including real-time applications are presented like necessary for car development. Special examples show the connection between simulation and test results.}, language = {en} } @incollection{ArrietaCastroRillWeber, author = {Arrieta Castro, Abel and Rill, Georg and Weber, Hans I.}, title = {Development of a Robust Integrated Control System to Improve the Stability of Road Vehicles}, series = {Multibody Mechatronic Systems}, volume = {54}, booktitle = {Multibody Mechatronic Systems}, editor = {Carvalho, Jo{\~a}o Carlos Mendes and Martins, Daniel and Simoni, Roberto and Simas, Henrique}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-67566-4}, doi = {10.1007/978-3-319-67567-1_48}, pages = {506 -- 516}, abstract = {Nowadays, new technologies are pushing the road vehicle limits further. Promising applications, e.g., self-driving cars, require a suitable control system that can maintain the vehicle's stability in critical scenarios. In most of current cars, the control systems actuates independently, meaning there is not a coordination or data sharing between them. This approach can produce a conflict between these standalone controllers and thus, no improvements on the vehicle's stability are achieved or even a worse scenario can be generated. In order to overcome these problems, an integrated approach is developed in this work. This integration, defined in this work as Integrated Control (IC), is done by an intelligence coordination of all standalone controllers inside the vehicle, i.e., Anti-Lock Braking System (ABS), Electronic Stability Program (ESP) and Four-Wheel Steering System (4WS). The ABS model was built using Fuzzy logic, for which only three rules were necessary to get a good performance. To design the ESP and the 4WS, the simple handling vehicle model was used as a reference behavior. The IC was designed using the hierarchical approach with two layers, i.e., the upper and lower layer. The upper one, observes the side slip angle and depends of its value the upper layer triggers the ESP or the 4WS. Finally, in order to prove the improvements of the IC system over the non-integrated approach, a full-size vehicle model was used to perform simulation in run-off-road and μ-split scenarios.}, language = {en} } @inproceedings{ArrietaCastroChavesRilletal., author = {Arrieta Castro, Abel and Chaves, Rafael B. and Rill, Georg and Weber, Hans I.}, title = {Use of Integrated Control to Enhance the Safety of Vehicles in Run-Off-Road Scenarios}, series = {Proceedings of DINAME 2017 : Selected Papers of the XVII International Symposium on Dynamic Problems of Mechanics}, booktitle = {Proceedings of DINAME 2017 : Selected Papers of the XVII International Symposium on Dynamic Problems of Mechanics}, editor = {Fleury, Agenor de T. and Rade, Domingos A. and Kurka, R. G.}, edition = {1. Auflage}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-91217-2}, issn = {2195-4356}, doi = {10.1007/978-3-319-91217-2_30}, pages = {431 -- 443}, abstract = {In this work, an integrated vehicle control system (IC) is tested in run-off-road scenarios. The integrated approach was employed in order to coordinate vehicle control systems, i.e. the Anti-Lock Brake System (ABS), Four-wheel Steering (4WS) and the Electronic Stability Program (ESP). To perform a run-off-road maneuver, a fuzzy virtual test driver was designed. By receiving the lateral position of an obstacle and the vehicle's relative yaw angle, the virtual test driver is capable of following a reference trajectory. Furthermore, to test the performance of the standalone controllers, i.e. ABS, ESP and 4WS, individual maneuvers are performed using a multibody vehicle model. The vehicle without any coordination between the control systems is used as reference. For the simulation results, it is concluded that the IC improves the vehicle stability and maneuverability in comparison with the non-integrated approach.}, language = {en} } @article{Rill2017, author = {Rill, Georg}, title = {Reducing the cornering resistance by torque vectoring (X International Conference on Structural Dynamics, EURODYN 2017)}, series = {Procedia Engineering}, volume = {199}, journal = {Procedia Engineering}, publisher = {Elsevier}, doi = {10.1016/j.proeng.2017.09.393}, pages = {3284 -- 3289}, year = {2017}, abstract = {Usually, torque vectoring is used to reduce a significant understeer behavior at high speed cornering. Thus, providing larger vehicles with a sportive touch. Even on typical front wheel driven cars torque vectoring control is available now. Torque vectoring is nearly a standard on electric driven vehicles. Complex control and optimization strategies are applied to improve the maneuverability in particular or to enhance the driving behavior and reduce the energy consumption in addition. This paper shows, that a quite simple strategy will enhance the maneuverability and simultaneously reduce the cornering resistance in sharp bends. At first, a case study with a fully non-linear and three-dimensional vehicle model is performed. It turned out that a full drive torque shift to the outer wheels improves the maneuverability and reduces the cornering resistance in addition. This results are verified by an optimization performed with a simpler four-wheeled handling model. Here, the front steering angles and the driving torques at each of the four wheels are considered as free parameters. Minimizing the cornering resistance by taking the equations of motion for the four-wheeled handling model as constraints will deliver an optimal set of parameters then.}, language = {en} } @inproceedings{HacklHirschbergLexetal., author = {Hackl, Andreas and Hirschberg, W. and Lex, C. and Rill, Georg}, title = {Tyre type dependent transient force behaviour by means of a maxwell model}, series = {The Dynamics of Vehicles on Roads and Tracks : Proceedings of the 25th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2017), Rockhampton, Queensland, Australia, 14-18 August 2017}, booktitle = {The Dynamics of Vehicles on Roads and Tracks : Proceedings of the 25th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2017), Rockhampton, Queensland, Australia, 14-18 August 2017}, editor = {Spiryagin, Maksym and Gordon, Timothy and Cole, Colin and McSweeney, Tim}, publisher = {CRC Press}, address = {London}, isbn = {1351057170}, doi = {10.1201/9781315265506}, pages = {157 -- 162}, abstract = {The present papers deals with the usability of an extended Maxwell model to describe the tyre dynamics during transient driving manoeuvres. In the present article, the para-metrisation process of a dynamic tyre model is investigated in a first step, using measurement data of tyre forces from a flat trac tyre test bench, (IABG 2016). Two tyre types of dimensions 255/50 R19 and 175/55 R15 are used. The practical applicability is discussed, considering the measurement procedure and the parameter optimisation process. In a second step, the performance of the dynamic tyre model is validated using measurements of manoeuvres under higher dynamic excitation. As a last step, an outlook is given on further research planned in which the presented model and parametrisation are adapted to a larger frequency range.}, language = {en} } @inproceedings{Rill, author = {Rill, Georg}, title = {Real-Time capable Multibody Model of dual Truck Front Axles}, series = {Proceedings of DINAME 2023 - Selected Papers of the XIX International Symposium on Dynamic Problems of Mechanics, 26 Feb - 03 Mar 2023, Piren{\´o}polis, Brazil}, booktitle = {Proceedings of DINAME 2023 - Selected Papers of the XIX International Symposium on Dynamic Problems of Mechanics, 26 Feb - 03 Mar 2023, Piren{\´o}polis, Brazil}, editor = {Fleury, Agenor de T.}, publisher = {Springer}, abstract = {Dual front steering axles are quite common in multi-axled heavy duty trucks. In standard layouts of such axle combinations, the steer motions of the wheels depend not only on the rotation of the steering wheel but also on the movements of the axles. As a consequence, the model complexity of the steering system should match with the complexity of the suspension model. The development of new technologies like advanced driver assistance systems or autonomous driving can only be accomplished efficiently using extensive simulation methods. Such kind of applications demand for computationally efficient vehicle models. This paper presents a steering system model for dual front axles of heavy duty trucks which supplements the suspension model of the axles. The model takes the torsional compliance of the steering column as well as the stiffness of the tie rods and the coupling rod into account. A quasi-static solution provides a straight forward computation including the partial derivatives required for an efficient implicit solver. The steering system model matches perfectly with comparatively lean, but sufficiently accurate multibody suspension models.}, language = {en} } @techreport{MichaelSternerMareikeJentschUweHolzhammer, author = {Michael Sterner, and Mareike Jentsch, and Uwe Holzhammer,}, title = {Energiewirtschaftliche und {\"o}kologische Bewertung eines Windgas-Angebotes}, publisher = {Fraunhofer Institute for Energy Economics and Energy System Technology}, address = {Kassel}, doi = {10.13140/RG.2.2.25093.68328}, abstract = {In this technical report, (1) the benefits of the new technology for future energy supply are discussed, (2) the climate protection effect of wind gas is discussed, and (3) a reasonable use of wind energy for gas generation is analyzed. In particular, windgas in the heat market is discussed in the utilization cascade of wind energy. The new "power-to-gas" concept opens up completely new possibilities for the integration of renewable energies and for coupling the electricity and gas grids. The Sabatier process, which has been known for 100 years, was first developed for this purpose in 2008 under the leadership of the Center for Solar Energy and Hydrogen Research and Fraunhofer IWES (formerly ISET) with electrolysis to create the "power-to-gas" concept for energy storage. A first pilot plant was built by ZSW Stuttgart on behalf of SolarFuel in 2009. This plant proves the technical feasibility of the new technology. Renewable gas is stored, transported and used as required as control and reserve energy via reconversion, e.g. in combined cycle power plants. In this way, decentrally generated renewable electricity is converted into a CO2 -neutral energy carrier with high energy density. The key advantage of renewable methane is the use of existing infrastructure such as gas grids, gas storage and end-use equipment for the integration of renewable energy. Technologies for natural gas are state of the art and commercially available. Methane also has three times the energy density of hydrogen.}, language = {en} } @techreport{ZacherlWopperMieslingeretal., author = {Zacherl, Florian and Wopper, Christoph and Mieslinger, Johann and Peis, Michael and Rabl, Hans-Peter}, title = {Schlussbericht zum Verbundvorhaben NAMOSYN: Nachhaltige Mobilit{\"a}t durch synthetische Kraftstoffe}, address = {Regensburg}, pages = {156}, abstract = {Im Labor f{\"u}r Verbrennungsmotoren und Abgasnachbehandlung der OTH-Regensburg sollten im Zuge des NAMOSYN-Projektes zwei Vertreter klimaneutraler Kraftstoffe an verschiedenen Systempr{\"u}fst{\"a}nden (Motor-, Einspritzpr{\"u}fstand, optisch zug{\"a}ngliche Einspritzkammer, …) und mit Hilfe von Simulationsmethoden f{\"u}r den Einsatz in bestehenden Verbrennungsmotoren untersucht werden. Synthetische Kraftstoffe aus der Gruppe der Oxymethylenether (OME) stellen eine CO2-neutrale Alternative zu fossilem Dieselkraftstoff dar. F{\"u}r Ottomotoren wurde untersucht, ob der synthetische Kraftstoff DMC/MeFo (Dimethylcarbonat \& Methylformiat) einen Ersatz f{\"u}r Ottokraftstoff darstellen kann, bzw. eine Drop-In-F{\"a}higkeit gegeben ist. Die OTH Regensburg bearbeitete 2 unabh{\"a}ngige Teilvorhaben zur motorischen Testung von synthetischen Kraftstoffen: „FC 1A: Motorische Testung von OME" und „FC 2: Untersuchung von C1-Oxygenaten f{\"u}r Ottomotoren". Die Projektlaufzeit betrug 3,5 Jahre, inkl. kostenneutraler Verl{\"a}ngerung um 6 Monate aufgrund der Corona-Pandemie. Im FC1A "AP2-Nachr{\"u}stung Dieselmotoren" der OTH Regensburg lag der Fokus auf der Erforschung der Potentiale und der Umr{\"u}stung eines Einzylinder-Dieselmotors mit Pumpe-Leitung-D{\"u}se-(PLD)-Einspritzsystem des Projektpartners Motorenfabrik Hatz GmbH und Co. KG f{\"u}r OME-Betrieb. Im AP2.1 wurden umfangreiche Daten gesammelt und Simulationsmodelle des Motors und PLD-Einspritzsystems erstellt und mit Dieselkraftstoff und OME validiert. Nachfolgend wurden Parameterstudien zur Geometrie des Einspritzsystems und der physikalischen Eigenschaften von OME durchgef{\"u}hrt. In AP2.2 und AP2.3 wurden umfangreiche Untersuchungen an einem Motor- und Einspritzsystempr{\"u}fstand mit Diesel und OME durchgef{\"u}hrt und der Steuerger{\"a}tedatensatz f{\"u}r den OME-Betrieb optimiert. Die Ergebnisse zeigen, dass die Umstellung des Kraftstoffs auf OME, insbesondere bei einfachen Motoren mit rudiment{\"a}rer Einspritztechnik und ohne Mittel zur NOx-Reduzierung (keine AGR oder SCR), ein enormes Potenzial zur Steigerung des Wirkungsgrads bei gleichzeitiger Reduzierung aller regulierten Schadstoffe (NOx, 𝑃N, 𝑃M, CO und 𝑉OC) er{\"o}ffnet. Die Ergebnisse und generierten Simulationsmodelle unterst{\"u}tzen eine schnelle Serienentwicklung und Einf{\"u}hrung von OME-Umr{\"u}stl{\"o}sungen. In FC 2 werden die vielversprechenden Kraftstoffe Methylformiat (MeFo) und Dimethylcarbonat (DMC) motorisch getestet. Untersuchungen am Kraftstoffsystem und wichtigen Komponenten dienen als Grundlage f{\"u}r das AP3. Im AP3 wird die Machbarkeit der DMC/MeFo-Verbrennung am Vollmotor demonstriert und die erwarteten Emissionsvorteile gegen{\"u}ber herk{\"o}mmlichen Ottokraftstoffen gezeigt. Abweichend von der urspr{\"u}nglichen Planung werden an der OTH Regensburg Kraftstoffblends aus Benzin und MeFo untersucht, um den Einsatzbereich des Kraftstoffs zu erweitern. In AP5 werden potentielle Mischungsverh{\"a}ltnisse analysiert und die Eigenschaften der ausgew{\"a}hlten Kraftstoffmischungen an einem Einspritzratenpr{\"u}fstand, an der Einspritzkammer und am Vollmotor untersucht. Es werden Einspritzverhalten, Gemischaufbereitung und Abgasemissionen bewertet. Zudem wird eine Kraftstoffmischanlage entwickelt und ein optischer Zugang am Vollmotor erm{\"o}glicht. Eine {\"O}lverd{\"u}nnungsmesstechnik wird eingesetzt, um den Kraftstoffeintrag ins Motor{\"o}l zu untersuchen}, language = {de} } @article{SchuemannMorichKaufholdetal., author = {Sch{\"u}mann, Malte and Morich, J. and Kaufhold, T. and B{\"o}hm, Valter and Zimmermann, Klaus and Odenbach, Stefan}, title = {A mechanical characterisation on multiple timescales of electroconductive magnetorheological elastomers}, series = {Magnetism and Magnetic Materials}, volume = {453}, journal = {Magnetism and Magnetic Materials}, number = {May}, publisher = {Elsevier}, doi = {10.1016/j.jmmm.2018.01.029}, pages = {198 -- 205}, abstract = {Magnetorheological elastomers are a type of smart hybrid material which combines elastic properties of a soft elastomer matrix with magnetic properties of magnetic micro particles. This leads to a material with magnetically controllable mechanical properties of which the magnetorheological effect is the best known. The addition of electroconductive particles to the polymer mix adds electrical properties to the material behaviour. The resulting electrical resistance of the sample can be manipulated by external magnetic fields and mechanical loads. This results in a distinct interplay of mechanical, electrical and magnetic effects with a highly complex time behaviour. In this paper a mechanical characterisation on multiple time scales was conducted to get an insight on the short and long-term electrical and mechanical behaviour of this novel material. The results show a complex resistivity behaviour on several timescales, sensitive to magnetic fields and strain velocity. The observed material exhibits fatigue and relaxation behaviour, whereas the magnetorheological effect appears not to interfere with the piezoresistive properties.}, language = {en} } @inproceedings{KetterlHeinrichReitmeieretal., author = {Ketterl, Hermann and Heinrich, Tobias and Reitmeier, Torsten and Hoelscher, Clemens}, title = {Emissionsabh{\"a}ngige Leistungsregelung f{\"u}r BHKW's}, series = {Tagungsband AALE 2020: Automatisierung und Mensch-Technik-Interaktion, 17. Fachkonferenz, 4. bis 6. M{\"a}rz 2020, Leipzig}, volume = {2020}, booktitle = {Tagungsband AALE 2020: Automatisierung und Mensch-Technik-Interaktion, 17. Fachkonferenz, 4. bis 6. M{\"a}rz 2020, Leipzig}, editor = {J{\"a}kel, Jens and Thiel, Robert}, publisher = {VDE-Verlag}, isbn = {978-3-8007-5180-8}, pages = {7}, language = {de} } @misc{OPUS4-6542, title = {Energieforschung}, edition = {Ausgabe 2023}, publisher = {OTH Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg / Regensburg Center of Energy and Resources (RCER)}, doi = {10.35096/othr/pub-6542}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-65422}, abstract = {{\"U}ber uns Das Regensburg Center of Energy and Resources (RCER) b{\"u}ndelt seit 2012 die Aktivit{\"a}ten der Ostbayerischen Technischen Hochschule Regensburg (OTH Regensburg) und der regionalen Wirtschaftsunternehmen auf dem Strategiefeld „Energie und Ressourcen". Mission: Energieforschung: vernetzen, voranbringen, vermitteln Das RCER f{\"o}rdert die Vernetzung verschiedener Disziplinen der Energieforschung innerhalb der OTH Regensburg und mit externen Partnern (Firmen, F{\"o}rdertr{\"a}gern, Forschungsinstitutionen, {\"o}ffentlichen Einrichtungen). Das RCER ist Ihr Partner beim Voranbringen von Kooperationen und Forschungsvorhaben durch Unterst{\"u}tzung in der Antragsphase, bei der Einwerbung von Projektmitteln und Projektbegleitung im Energiebereich. Das RCER steht f{\"u}r die Vermittlung von Know-how, Basiswissen, aktuellen Fragen und den Technologietransfer rund um das Thema Energie zwischen Wissenschaft, Wirtschaft, Gesellschaft und Politik. Vision Wir sind Ihr erster Ansprechpartner und Motor f{\"u}r innovative Energieforschung. Werte Verl{\"a}sslichkeit, Kompetenz, Verantwortungsbewusstsein.Regional verwurzelt und weltoffen}, language = {de} } @misc{Sterner, author = {Sterner, Michael}, title = {Strom - W{\"a}rme - Verkehr - Industrie: das Zusammenspiel der Sektoren {\"u}ber Power-to-X}, series = {Deutscher Ingenieurtag 2021, D{\"u}sseldorf 20. Mai 2021}, journal = {Deutscher Ingenieurtag 2021, D{\"u}sseldorf 20. Mai 2021}, publisher = {VDI-Verlag}, language = {de} }