@article{ChatzitakisSafarovOpferkuchetal., author = {Chatzitakis, Paris and Safarov, Javid and Opferkuch, Frank and Dawoud, Belal}, title = {Experimental investigation of an absorption heat pump with organic working pairs}, series = {Applied Thermal Engineering}, volume = {163}, journal = {Applied Thermal Engineering}, number = {December}, publisher = {Elsevier}, doi = {10.1016/j.applthermaleng.2019.114311}, abstract = {As part of a systematic approach towards the search for alternative absorption heat pump (AHP) working pairs that could potentially provide comparable performance to conventional ones, a previous work performed a detailed theoretical cycle analysis and simulation that revealed concrete correlations between key working fluid thermophysical properties and AHP performance indicators. Following this work, targeted combinations of two organic refrigerants, 2,2,2-trifluoroethanol (TFE) and 2,2,3,3,3-pentafluoropropanol (5FP) and two organic absorbents, 1,3-dimethyl-2-imidazolidinone (DMI) and 2-pyrrolidone (PYR) were tested in a prototype 5 kW AHP, based on a highly compact plate heat exchanger design, which has been previously introduced. The purpose of this effort was to test the findings of the previous work with experimental measurements. The working pair combinations were also subjected to vapor liquid equilibrium (VLE) and viscosity measurements, in order to determine reliable activity coefficient and improve the accuracy of the simulations. The experimental performance data agree well with the COP simulations and show to be consistent with the conclusions derived from the previous theoretical work.}, language = {en} } @article{HansenHoeblerPurretal., author = {Hansen, B. and Hoebler, Michael and Purr, Stephan and Meinhardt, J. and Merklein, Marion}, title = {Basics for inline measurement of tribological conditions in series production of car body parts}, series = {IOP Conference Series: Materials Science and Engineering}, volume = {651}, journal = {IOP Conference Series: Materials Science and Engineering}, publisher = {IOP Publishing}, doi = {10.1088/1757-899x/651/1/012050}, abstract = {The quality of car body parts in series production is strongly dependent on the tribological behavior. Fluctuating material properties such as the sheet roughness and the amount of lubricant have an influence on the forming process. On the basis of large amounts of data it is possible to investigate the friction behavior in series production and to make process adjustments if required. Therefore, inline measurement systems have a great potential to detect the sheet roughness during the cutting process of blanks in the coil line. Furthermore, contactless systems are advantageous as they do not damage the surface. Nevertheless, the optical measuring is influenced by the lubricant layer on top of the surface. Therefore, the previously unknown impact of the lubricant on the measuring result is investigated. Within this study, stationary optical roughness measurements have been conducted using different amounts of lubricant on hot-dip galvanized EDT steel. The results demonstrate the influence of different amounts of lubricant on the sheet roughness measurement. Hence, it is possible to correct the inline measuring results and gain knowledge of fluctuating surface roughness. In addition, strip drawing test has been carried out to investigate the effect of fluctuating tribological conditions.}, language = {en} } @article{SavelevFetisovChashinetal., author = {Savelev, Dmitrii V. and Fetisov, Leonid Y. and Chashin, Dmitri V. and Shabin, P. A. and Vyunik, D. A. and Fedulov, Feodor and Kettl, Wolfgang and Shamonin (Chamonine), Mikhail}, title = {Method of Measuring Deformations of Magnetoactive Elastomers under the Action of Magnetic Fields}, series = {Russian Technological Journal}, volume = {7}, journal = {Russian Technological Journal}, number = {4}, doi = {10.32362/2500-316x-2019-7-4-81-91}, pages = {81 -- 91}, language = {ru} } @inproceedings{ParedesKeimNonnetal., author = {Paredes, Marcelo and Keim, Vincent and Nonn, Aida and Wierzbicki, Tomasz}, title = {Effect of plasticity parameter on the crack propagation in steel pipelines}, series = {Proceedings of the conference on Technology for future and ageing piplines, Ghent, Belgium}, booktitle = {Proceedings of the conference on Technology for future and ageing piplines, Ghent, Belgium}, language = {en} } @article{DiamantidisSykoraLenzi, author = {Diamantidis, Dimitris and S{\´y}kora, Miroslav and Lenzi, Daniele}, title = {Optimising Monitoring: Standards, Reliability Basis and Application to Assessment of Roof Snow Load Risks}, series = {Structural Engineering International}, volume = {28}, journal = {Structural Engineering International}, number = {3}, publisher = {Taylor\&Francis}, doi = {10.1080/10168664.2018.1462131}, pages = {269 -- 279}, abstract = {This paper addresses the optimisation of monitoring and decision-making criteria regarding the future use of structures. The current state of practice in standards and reliability framework are initially summarised. A general methodology for obtaining cost-optimal decisions is then presented on the basis of limit state design, probabilistic reliability analysis and cost estimates. The implementation of the risk-based approach is illustrated in a case study dealing with the roof of a stadium located in northern Italy. As the roof fails to comply with the requirements of the Eurocodes, the installation of a permanent monitoring system is recommended to allow for a real-time reliability assessment. The results demonstrate the potential of monitoring systems and probabilistic reliability analysis for supporting decisions regarding safety measures such as snow removal or temporary closure of the stadium, as well as reflecting the need to implement the discussed procedures in future standards.}, language = {en} } @article{DiermeierSindersbergerKrenkeletal., author = {Diermeier, Andreas and Sindersberger, Dirk and Krenkel, Lars and Rosell, X. C. and Monkman, Gareth J.}, title = {Controllable Magnetoactive Polymer Conduit}, series = {The Open Mechanical Engineering Journal}, volume = {12}, journal = {The Open Mechanical Engineering Journal}, number = {1}, publisher = {Bentham}, pages = {192 -- 200}, abstract = {Objective: Magneto-active Polymers (MAP) are smart materials whose mechanical characteristics, such as elastic and shear moduli, may be controllable by means of an externally applied magnetic field. Methods: Various additives may be used to influence the characteristics of the polymer matrix whilst a suspension of soft and/or hard magnetic particles determine the magnetic properties of the composite. Both pre-cure and post-cure magnetization is possible. Results: A range of control strategies have been investigated for evaluation of the system using fluids of differing kinematic viscosity. Conclusion: Depending on the degree of magnetic field homogeneity, magneto-deformation and magnetostriction contribute to MAP actuation. This paper presents a novel application in the form of a peristaltic MAP tube system, applicable to flow control and pumping of hemorheological fluids in blood circulatory systems for biomedical research purposes.}, language = {en} } @article{Brueckl, author = {Br{\"u}ckl, Oliver}, title = {Pl{\"a}doyer f{\"u}r die wettbewerbliche Bereitstellung von Blindleistung}, series = {ew - Magazin f{\"u}r die Energiewirtschaft - Spezial: Digitalisierung}, volume = {117}, journal = {ew - Magazin f{\"u}r die Energiewirtschaft - Spezial: Digitalisierung}, number = {1}, publisher = {VDE Verlag}, organization = {VDE Verlag}, pages = {46 -- 48}, language = {de} } @inproceedings{HaslbeckBrueckl, author = {Haslbeck, Matthias and Br{\"u}ckl, Oliver}, title = {Netzplanungsprozess zur dezentralen Nutzung von Blindleistungsquellen in Verteilungsnetzen}, series = {Tagungsband der Fachtagung "Zuk{\"u}nftige Stromnetze f{\"u}r erneuerbare Energien" am 30./31. Januar 2018 in Berlin}, booktitle = {Tagungsband der Fachtagung "Zuk{\"u}nftige Stromnetze f{\"u}r erneuerbare Energien" am 30./31. Januar 2018 in Berlin}, abstract = {Das vom BMWi gef{\"o}rderte Forschungsprojekt SyNErgie (03/2015 bis 05/2018) besch{\"a}ftigt sich mit der Weiterentwicklung von Netzplanungsprozessen [1]. Im Fokus steht dabei die Modellierung von Blindleistungsfl{\"u}ssen und die dezentrale Nutzung von Blindleistungsquellen (z. B. Wechselrichter, Ladedrosseln, Kondensatoren) in Mittelspannungsnetzen, {\"u}ber welche der Blindleistungshaushalt letztendlich beeinflusst werden soll. Diese Ver{\"o}ffentlichung konzentriert sich auf die konzipierte Erweiterung des Netzplanungsprozesses zur Einbindung von Blindleistungsquellen im Verteilungsnetz in ein Blindleistungsmanagement. Deren einzelne Phasen werden erl{\"a}utert und anschließend die Netz-Sensitivit{\"a}ts- und -Restriktionsanalyse anhand eines realen Mittelspannungsnetzes demonstriert. Abschließend werden m{\"o}gliche Abschw{\"a}chungs- und Verst{\"a}rkungseffekte im Hinblick auf einen Blindleistungsabruf {\"u}ber mehrere Spannungsebenen hinweg diskutiert.}, language = {de} } @inproceedings{KreuzerHaslbeckBrueckl, author = {Kreuzer, Reinhard and Haslbeck, Matthias and Br{\"u}ckl, Oliver}, title = {Modellierung von Mittelspannungsnetzen zur verbesserten Nachbildung von Wirk- und Blindleistungsfl{\"u}ssen}, series = {Tagungsband der Fachtagung "Zuk{\"u}nftige Stromnetze f{\"u}r erneuerbare Energien" am 30./31. Januar 2018 in Berlin}, booktitle = {Tagungsband der Fachtagung "Zuk{\"u}nftige Stromnetze f{\"u}r erneuerbare Energien" am 30./31. Januar 2018 in Berlin}, abstract = {Das vom BMWi gef{\"o}rderte Forschungsprojekt SyNErgie (03/2015 bis 05/2018) besch{\"a}ftigt sich mit der Weiterentwicklung von Netzplanungsprozessen [1]. Im Fokus steht dabei die Modellierung von Blindleistungsfl{\"u}ssen und die dezentrale Nutzung von Blindleistungsquellen (z. B. Wechselrichter, Ladedrosseln, Kondensatoren) in Mittelspannungsnetzen, {\"u}ber welche der Blindleistungshaushalt letztendlich beeinflusst werden soll. Im Rahmen dieses Beitrags wird anhand eines realen Mittelspannungsnetzes (MS-Netz) gezeigt, welche Modellierungsschritte zur Erstellung eines m{\"o}glichst realit{\"a}tsnahen Simulationsabbilds n{\"o}tig sind. Dies ist notwendig, um der Verteilnetzplanung eine robuste Planungsgrundlage f{\"u}r die Ableitung von Entscheidungen im Rahmen eines Blindleistungsmanagements zur Verf{\"u}gung zu stellen.}, language = {de} } @inproceedings{BerlingHaslbeckBrueckl, author = {Berling, Andreas and Haslbeck, Matthias and Br{\"u}ckl, Oliver}, title = {Interpretation und Relevanz verschiedener Blindleistungsarten f{\"u}r die Modellierung von Niederspannungsnetzen in der Netzplanung}, series = {Tagungsband der Fachtagung "Zuk{\"u}nftige Stromnetze f{\"u}r erneuerbare Energien" am 30./31. Januar 2018 in Berlin}, booktitle = {Tagungsband der Fachtagung "Zuk{\"u}nftige Stromnetze f{\"u}r erneuerbare Energien" am 30./31. Januar 2018 in Berlin}, language = {de} } @article{KoderSchwanzerZacherletal., author = {Koder, Alexander and Schwanzer, Peter and Zacherl, Florian and Rabl, Hans-Peter and Mayer, Wolfgang and Gruber, Georg and Dotzer, Thomas}, title = {Combustion and emission characteristics of a 2.2L common-rail diesel engine fueled with jatropha oil, soybean oil, and diesel fuel at various EGR-rates}, series = {Fuel}, volume = {228}, journal = {Fuel}, number = {September}, publisher = {Elsevier}, doi = {10.1016/j.fuel.2018.04.147}, pages = {23 -- 29}, abstract = {To investigate the combustion and emission behavior of straight vegetable oils (SVO), jatropha oil, soybean oil, and diesel fuel were tested. For this research, a 2.2L common-rail engine with a two-stage turbocharging concept was equipped with a cylinder pressure indication system, an exhaust-gas analyzer, an AVL Micro Soot sensor and a Scanning Mobility Particle Sizer 3936 (SMPS) device to detect the particle-size-distribution (PSD). At a low and mid-load engine-operating point (EOP), the thermodynamic and emissions were investigated under various exhaust gas recirculation (EGR) rates with respect to the PSD. Moreover, the injection behavior of the three test fuels was analyzed separately using an injection rate analyzer. This procedure facilitates the thermodynamic investigations of the engine process and allows the calculation of the hydraulic delay (HD) as well as the ignition delay (ID). The ID of the SVO fuels compared to diesel fuel was found to be lower at all engine-operating modes, while jatropha oil always showed the shortest ID. In the particulate-nitrogen oxide (NOX) trade-off, the SVO fuels showed higher particulate matter (PM) emissions at the low-load EOP, whereas the PM emissions of diesel fuel overtop the SVO fuels at a higher engine load. With increased EGR-rates, a rise in the particle size was observed for all fuels. At the low-load EOP, the SVO fuels showed larger particles for high EGR-rates. This effect also changed by increasing the engine-load to the mid-load EOP, wherein the particle size of the diesel fuel emissions is higher by applying elevated EGR-rates.}, language = {en} } @incollection{StadlerSterner, author = {Stadler, Ingo and Sterner, Michael}, title = {Urban Energy Storage and Sector Coupling}, series = {Urban Energy Transition}, booktitle = {Urban Energy Transition}, editor = {Droege, Peter}, edition = {2. ed.}, publisher = {Elsevier}, isbn = {978-0-08-102074-6}, doi = {10.1016/B978-0-08-102074-6.00026-7}, pages = {225 -- 244}, abstract = {Global warming, greenhouse gas emissions, and the general transition toward renewable energy resources are mentioned many times within this book, and will not be repeated again here. Countries that are transitioning to use of more renewable energy sources are mainly using wind and solar power—except for a few countries that, due to their prerequisites, will mainly use hydro power and/or bioenergy. The transmission process in terms of energy generation so far is mainly happening in rural areas—not in urban centers. Most technologies do not really play an important role in urban areas, and are mainly focused on the application of solar energy. Solar energy is widely applied more in rural areas, although investigations show that its application in urban areas already fits well into the existing grid infrastructure. Whereas rural areas are more prone to grid integration problems, the energy infrastructure in urban centers is already well prepared for renewables integration. In fostering tight bundles of potentially linked energy generation, distribution, networking, and use across power and thermal systems in stationary and mobile modes, urban centers become particularly critical in the energy transition processes as energy systems are becoming completely based on renewable sources without a nuclear or fossil-based backbone. This chapter discusses the almost unlimited energy storage possibilities. It will show their enormous capabilities, but also their significant differences in many physical and economical parameters. Next, the authors discuss the necessity of combining and coupling the different energy sectors for electricity, heat, cold, gas, and transport. Finally, the authors present the conclusion that only when coupling the energy sectors and using cheap and efficient energy storage options from one energy sector to solve challenges within another energy sector will the energy transition process be managed in an efficient way.}, language = {en} } @article{SykoraMarkovaDiamantidis, author = {S{\´y}kora, Miroslav and Markova, Jana and Diamantidis, Dimitris}, title = {Bayesian network application for the risk assessment of existing energy production units}, series = {Reliability Engineering \& System Safety}, volume = {169}, journal = {Reliability Engineering \& System Safety}, number = {January}, publisher = {Elsevier}, doi = {10.1016/j.ress.2017.09.006}, pages = {312 -- 320}, abstract = {The assessment of existing infrastructures in the energy sector is of great economic significance worldwide. Fossil power stations are reaching their design service life and rational decisions concerning extensions of service life, maintenance and replacements of devices should be based on updated information of the actual conditions of the energy devices and their components, and on cost-benefit analysis using risk analysis and probabilistic optimisation procedures. The contribution provides an integrated framework for probabilistic reliability and risk assessment of existing energy production units considering availability and human safety criteria. An extensive case study focused on risks of an energy production unit in a fossil power station is provided to support practical applications. A Bayesian network is thereby implemented to assess the risks of the selected production unit. Special emphasis is given to the input data consisting of failure rates obtained from recorded data and expert judgements. The influence of uncertainties in the considered performance indicators on the availability of the unit is analysed. It is shown that a reasonably simplified framework can provide a valuable assessment of the influence of individual devices and their components on availability and societal risk, identifying thus the major risk contributors. (C) 2017 Elsevier Ltd. All rights reserved.}, language = {en} } @article{WeberHaug, author = {Weber, Karsten and Haug, Sonja}, title = {Ist automatisiertes Fahren nachhaltig?}, series = {TATuP - Zeitschrift f{\"u}r Technikfolgenabsch{\"a}tzung in Theorie und Praxis}, volume = {27}, journal = {TATuP - Zeitschrift f{\"u}r Technikfolgenabsch{\"a}tzung in Theorie und Praxis}, number = {2}, publisher = {Karlsruhe Institute of Technology (KIT)}, doi = {10.14512/tatup.27.2.16}, pages = {16 -- 22}, abstract = {Automatisiertes Fahren st{\"o}ßt derzeit noch auf große Skepsis. Eine disruptive Strategie bei der Einf{\"u}hrung (voll-)automatisierten Fahrens k{\"o}nnte daher auf fehlende Akzeptanz treffen. Um dem zu entgehen, laufen evolution{\"a}re Strategien darauf hinaus, durch die Entwicklung adaptiver Fahrassistenzsysteme Vertrautheit, Vertrauen und damit Akzeptanz bei den prospektiven NutzerInnen zu schaffen. Erste Ergebnisse einer Pilotstudie lassen jedoch Zweifel an der Nachhaltigkeit dieser Strategie aufkommen.}, language = {de} } @inproceedings{KeimNonnLenzetal., author = {Keim, Vincent and Nonn, Aida and Lenz, D. and Brinnel, Viktoria and M{\"u}nstermann, Sebastian}, title = {Simulation of the ductile fracture behaviour of high toughness pipeline steels using combined damage models}, series = {Proceedings of the conference on Technology for future and ageing piplines, Ghent, Belgium}, booktitle = {Proceedings of the conference on Technology for future and ageing piplines, Ghent, Belgium}, language = {en} } @article{LeeSchubertOoietal., author = {Lee, Wai-Kong and Schubert, Martin J. W. and Ooi, Boon Yaik and Ho, Stanley Jian-Qin}, title = {Multi-source energy harvesting and storage for floating wireless sensor network nodes with Long Range Communication Capability}, series = {IEEE Transactions on Industry Applications}, volume = {54}, journal = {IEEE Transactions on Industry Applications}, number = {3}, publisher = {IEEE}, doi = {10.1109/TIA.2018.2799}, pages = {2606 -- 2615}, abstract = {Wireless sensor networks are widely used for environmental monitoring in remote areas. They are mainly composed of wireless sensor nodes, usually powered by batteries with limited capacity, but are expected to communicate in long range and operate for extended time periods. To overcome these limitations, many energy harvesting techniques are proposed to power wireless nodes for prolonged operation, whereas multihop techniques are utilized to extend the communication range. In this paper, a novel floating device with multisource energy harvesting technology that can be used as a wireless sensor node is proposed. The long range communication between wireless sensor nodes and a gateway is established through LoRa technology. In addition to conventional solar panels, an energy harvesting technique based on thermoelectric generators exploiting thermal differences created between water surface and materials exposed to sunlight is proposed. Energy generated from photovoltaic and thermoelectric generators is combined to power the wireless sensor node. This floating device consumes 6.6216 Wh per day when used as a wireless sensor node for the collection and transmission of environmental data. The sensor node can operate on a water surface for at least 9.6 days when it is not exposed to sunlight. During a sunny day, the floating device can harvest 8.375 Wh from solar panels and 0.425 Wh from thermoelectric generation. In other words, the floating device harvests sufficient energy to be self-sustaining during sunny days.}, language = {en} } @inproceedings{WeberHaug, author = {Weber, Karsten and Haug, Sonja}, title = {Automatisiertes Fahren: Evolution{\"a}re Weiterentwicklung statt Disruption}, series = {Vierte Jahreskonferenz des Netzwerks INDIGO zum Thema "Mobilit{\"a}t", 23.11.2018, , TH Deggendorf}, booktitle = {Vierte Jahreskonferenz des Netzwerks INDIGO zum Thema "Mobilit{\"a}t", 23.11.2018, , TH Deggendorf}, language = {de} } @inproceedings{NonnParedesKeimetal., author = {Nonn, Aida and Paredes, Marcelo and Keim, Vincent and Wierzbicki, Tomasz}, title = {Comparison of Fracture Models to Quantify the Effects of Material Plasticity on the Ductile Fracture Propagation in Pipelines}, series = {Proceedings of the 2018 12th International Pipeline Conference, Volume 3: Operations, Monitoring, and Maintenance, Materials and Joining, September 24-28, 2018, Calgary, Alberta, Canada}, booktitle = {Proceedings of the 2018 12th International Pipeline Conference, Volume 3: Operations, Monitoring, and Maintenance, Materials and Joining, September 24-28, 2018, Calgary, Alberta, Canada}, doi = {10.1115/IPC2018-78366}, abstract = {Various numerical approaches have been developed in the last years aimed to simulate the ductile fracture propagation in pipelines transporting CO2 or natural gas. However, a reliable quantification of the influence of material plasticity on the fracture resistance is still missing. Therefore, more accurate description of the material plasticity on the ductile fracture propagation is required based on a suitable numerical methodology. In this study, different plasticity and fracture models are compared regarding the ductile fracture propagation in X100 pipeline steel with the objective to quantify the influence of plasticity parameters on the fracture resistance. The plastic behavior of the investigated material is considered by the quadratic yield surface in conjunction with a non-associated quadratic plastic flow potential. The strain hardening can be appropriately described by the mixed Swift-Voce law. The simulations of ductile fracture are conducted by an uncoupled, modified Mohr-Coulomb (MMC) and the micromechanically based Gurson-Tvergaard-Needleman (GTN) models. In contract to the original GTN model, the MMC model is capable of describing ductile failure over wide range of stress states. Thus, ductile fracture resistance can be estimated for various load and fracture scenarios. Both models are used for the simulation of fracture propagation in DWTT and 3D pressurized pipe sections. The results from the present work can serve as a basis for establishing the correlation between plasticity parameters and ductile fracture propagation.}, language = {en} } @article{SykoraHolickyJungetal., author = {S{\´y}kora, Miroslav and Holicky, Milan and Jung, Karel and Diamantidis, Dimitris}, title = {Human safety criteria for risk-based structural design}, series = {International Journal of Safety and Security Engineering}, volume = {8}, journal = {International Journal of Safety and Security Engineering}, number = {2}, publisher = {WIT Press}, doi = {10.2495/SAFE-V8-N2-287-298}, pages = {287 -- 298}, abstract = {Risk and reliability criteria are well established in many industrial sectors such as the offshore, chemi- cal or nuclear industries. Comparative risk thresholds have been specified to allow a responsible organization or regulator to identify activities, which impose an acceptable level of risk concerning the participating individuals, or society as a whole. The scope of this contribution is to present target reliability criteria based on acceptable human safety levels. Application of theoretical principles is illustrated by examples of railway engineering structures. Initially it is shown how civil engineering structures for which human safety criteria play a role are classified according to Eurocodes. Examples include bridges, tunnels or station buildings. The general concepts for risk acceptance are then briefly reviewed, particularly in their relation to the target reliability criteria. The distinction between the two types of criteria is made: group risk and the acceptance criterion based on the Life Quality Index LQI approach introduced by ISO 2394:2015. The differences between the criteria for new and existing structures are discussed. The application is illustrated by an example of a bridge crossing an important railway line. It appears that while benefits and costs of a private stakeholder or public authority are reflected by economic optimisation, the society should define the limits for human safety to achieve uniform risks for various daily-life activities and across different industrial sectors. Keywords: group risk, human safety, individual risk, Life Quality Index, railway, risk acceptance, structure, target reliability}, language = {en} } @inproceedings{DiamantidisSykoraBertacca, author = {Diamantidis, Dimitris and S{\´y}kora, Miroslav and Bertacca, Elena}, title = {Obsolescence Rate: Framework, Analysis and Influence on Risk Acceptance Criteria}, series = {6th International Symposium on Life-Cycle Civil Engineering (IALCCE), Ghent, Belgium}, booktitle = {6th International Symposium on Life-Cycle Civil Engineering (IALCCE), Ghent, Belgium}, abstract = {Buildings are major long lasting assets of the society and business enterprises and form a significant part of infrastructure management. They require continual maintenance and in many cases they can become inap-propriate for their original purpose due to obsolescence and are demolished. The present contribution ex-plores the obsolescence of buildings and in particular the definitions of obsolescence, the related influenc-ing factors and the associated uncertainties. Thereby definitions of the obsolescence rate based on the physi-cal and useful (service) life are clarified. The experienced useful life of buildings in Finland, Germany and North America is statistically analysed, utilizing available databases, and comparisons with the design (minimum) working life specified in standards are made. The probability of not exceeding the required min-imum service life is evaluated and discussed. Whereas many factors affecting the obsolescence rate are be-yond the control of civil engineers, particular attention needs to be paid to cases where the service life of the structure is determined by physical aspects related to deterioration. These cases are identified and recom-mendations to improve structural design are offered. The service life and the related renewal rate is influ-encing the risk acceptance criteria as given in ISO 2394. Such criteria are derived on the basis of economic optimization and the LQI marginal safety costs principle. A statistical model for the renewal rate is obtained and its influence on the target reliability is investigated for a representative failure limit state. The influence of the obsolescence rate is quantified and critically disputed.}, language = {en} } @article{KurzweilShamoninChamonine, author = {Kurzweil, Peter and Shamonin (Chamonine), Mikhail}, title = {State-of-Charge Monitoring by Impedance Spectroscopy during Long-Term Self-Discharge of Supercapacitors and Lithium-Ion Batteries}, series = {Batteries}, volume = {4}, journal = {Batteries}, number = {3}, publisher = {MPDI}, doi = {10.3390/batteries4030035}, pages = {1 -- 13}, abstract = {Frequency-dependent capacitance C(ω) is a rapid and reliable method for the determination of the state-of-charge (SoC) of electrochemical storage devices. The state-of-the-art of SoC monitoring using impedance spectroscopy is reviewed, and complemented by original 1.5-year long-term electrical impedance measurements of several commercially available supercapacitors. It is found that the kinetics of the self-discharge of supercapacitors comprises at least two characteristic time constants in the range of days and months. The curvature of the Nyquist curve at frequencies above 10 Hz (charge transfer resistance) depends on the available electric charge as well, but it is of little use for applications. Lithium-ion batteries demonstrate a linear correlation between voltage and capacitance as long as overcharge and deep discharge are avoided.}, language = {en} } @misc{Weiss, author = {Weiss, Nils}, title = {Vulnerabilities of OBD2 Dongles}, series = {RCAR Annual Conference, 2018, Munich, Germany}, journal = {RCAR Annual Conference, 2018, Munich, Germany}, language = {en} } @inproceedings{FuhrmannNiemetz, author = {Fuhrmann, Thomas and Niemetz, Michael}, title = {Transdisciplinary Bachelor Course Connecting Business and Electrical Engineering}, series = {4th International Conference on Higher Education Advances (HEAd'18), 2018, Universitat Polit{\`e}cnica de Val{\`e}ncia, Val{\`e}ncia}, booktitle = {4th International Conference on Higher Education Advances (HEAd'18), 2018, Universitat Polit{\`e}cnica de Val{\`e}ncia, Val{\`e}ncia}, doi = {10.4995/HEAd18.2018.8056}, abstract = {The OTH Regensburg has a broad variety of study programs in technical, business, social and health sciences. Up to now there is no integral connection in the bachelor curricula between business and technical faculties except for some small subjects. The scope of this project is to develop a new course specialization which connects engineering and business thinking. Electrical engineering students should learn basics of business science and how managers think. Business students should vice versa learn fundamentals of engineering and how engineers solve problems. Students from both faculties work together in projects where they act like start-up companies developing a new product and bringing it into the market. It is seen a transdisciplinary effect: These projects gain innovative results between the disciplines compared to student projects of one isolated discipline. Evaluation results from the first two cohorts indicate high student satisfaction, high learning success as well as directions for further improvement.}, language = {en} } @incollection{ArrietaCastroRillWeber, author = {Arrieta Castro, Abel and Rill, Georg and Weber, Hans I.}, title = {Development of a Robust Integrated Control System to Improve the Stability of Road Vehicles}, series = {Multibody Mechatronic Systems}, volume = {54}, booktitle = {Multibody Mechatronic Systems}, editor = {Carvalho, Jo{\~a}o Carlos Mendes and Martins, Daniel and Simoni, Roberto and Simas, Henrique}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-67566-4}, doi = {10.1007/978-3-319-67567-1_48}, pages = {506 -- 516}, abstract = {Nowadays, new technologies are pushing the road vehicle limits further. Promising applications, e.g., self-driving cars, require a suitable control system that can maintain the vehicle's stability in critical scenarios. In most of current cars, the control systems actuates independently, meaning there is not a coordination or data sharing between them. This approach can produce a conflict between these standalone controllers and thus, no improvements on the vehicle's stability are achieved or even a worse scenario can be generated. In order to overcome these problems, an integrated approach is developed in this work. This integration, defined in this work as Integrated Control (IC), is done by an intelligence coordination of all standalone controllers inside the vehicle, i.e., Anti-Lock Braking System (ABS), Electronic Stability Program (ESP) and Four-Wheel Steering System (4WS). The ABS model was built using Fuzzy logic, for which only three rules were necessary to get a good performance. To design the ESP and the 4WS, the simple handling vehicle model was used as a reference behavior. The IC was designed using the hierarchical approach with two layers, i.e., the upper and lower layer. The upper one, observes the side slip angle and depends of its value the upper layer triggers the ESP or the 4WS. Finally, in order to prove the improvements of the IC system over the non-integrated approach, a full-size vehicle model was used to perform simulation in run-off-road and μ-split scenarios.}, language = {en} } @inproceedings{BoehmSchorrZimmermannetal., author = {B{\"o}hm, Valter and Schorr, Philipp and Zimmermann, Klaus and Zentner, Lena}, title = {An Approach to the Estimation of the Actuation Parameters for Mobile Tensegrity Robots with Tilting Movement Sequences}, series = {2018 International Conference on Reconfigurable Mechanisms and Robots (ReMAR); 20-22 June 2018; Delft, Netherlands}, booktitle = {2018 International Conference on Reconfigurable Mechanisms and Robots (ReMAR); 20-22 June 2018; Delft, Netherlands}, publisher = {IEEE}, doi = {10.1109/REMAR.2018.8449871}, pages = {1 -- 8}, abstract = {This paper deals with the locomotion by tilting sequences of shape-variable compliant tensegrity structures. The shape of these structures is controlled by manipulating their prestress state. The tensegrity structure is tilting as consequence of a suitable variation of its shape. By multiple repetition of such tilting sequences a motion is generated. Quasi-static considerations for the considered structures are presented in order to estimate the actuation parameters. For a proper number of actuators this quasi-static approach enables an analytical calculation of the actuation parameters of the structure in order to control the geometrical configuration as required. As an example a two-dimensional tensegrity structure which is in contact with a horizontal plane due to gravity is considered. By successive tilting sequences a uniaxial motion results. The excitation of the structure is calculated for a given change of shape with the quasi-static analysis. The according results are compared with transient dynamic simulations. Qualitative conclusions about the motion behavior and the usability of the quasi-static approach are given.}, language = {en} } @inproceedings{MaeuleRabl, author = {M{\"a}ule, Paul and Rabl, Hans-Peter}, title = {Correlation of Oil Emissions with Particulate Emissions of Gasoline Engines}, series = {Internationales AVL-Forum Abgas- und Partikelemissionen, 20. und 21. Februar 2018, Ludwigsburg}, booktitle = {Internationales AVL-Forum Abgas- und Partikelemissionen, 20. und 21. Februar 2018, Ludwigsburg}, publisher = {AVL Deutschland}, address = {Mainz}, pages = {1 -- 9}, abstract = {Recent developments in exhaust gas legislation make it necessary to focus the research at the particulate emissions from gasoline engines and technologies for their reduction. In addition to the particulates resulting from the combustion of the fuel, the oil emissions represent another possible source for particulate emissions. This paper presents a measurement method which can be used to quantify stationary as well as dynamic oil emissions of gasoline engines. Furthermore, the correlation between the oil emissions and the particulate emissions is the focus of the investigations. Conventional methods for the determination of the oil emissions, such as the gravimetric and the volumetric measurement, are unsuitable since they require long engine operation times to provide useful results. These methods therefore do not allow a fast online measurements during the dynamic operation. For this reason, a new measuring method was used, which allows for a time-resolved online measurement of the oil emissions. This measurement method is based on the sulfur tracer method, which uses the sulfur that is naturally contained in the engine oil as a tracer. The sulfur concentration in the exhaust gas is determined by using an Ion-Molecule-Reaction mass spectrometer. The determination of the particulate emissions corresponds to the PMP regulation. The studies carried out under steady state and dynamic conditions show a clear correlation between the oil consumption and the number of particulates in the exhaust gas. In the case of the dynamic measurements it could also be shown that time-resolved measurements of the oil consumption are possible with the used measurement setup. In addition, it was shown that the number of particulates does not influence the measurement of the SO2-concentration. Furthermore, the different effects of burned and unburned oil emissions have been evaluated by the dosing of the oil into the exhaust gas. The overall conclusion of the measurements shows a strong influence of the oil emissions on the particulate emissions. Therefore, it is crucial to reduce the oil emissions. Possible approaches for this reduction can be improved turbocharger sealing concepts, new piston ring designs or more efficient oil separators for the crankcase ventilation system.}, language = {en} } @inproceedings{SmolareckFaisstSchneider, author = {Smolareck, Elisabeth and Faisst, Holger and Schneider, Ralph}, title = {Modellbasierte Korrektur von Inertialsensor-Signalen - Ein Schritt auf dem Weg zum hochautomatisierten Fahren}, series = {Konferenz: AALE 2018 - 15. Fachkonferenz, Das Forum f{\"u}r Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft 01.03.2018 - 02.03.2018 in K{\"o}ln, Deutschland}, booktitle = {Konferenz: AALE 2018 - 15. Fachkonferenz, Das Forum f{\"u}r Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft 01.03.2018 - 02.03.2018 in K{\"o}ln, Deutschland}, publisher = {VDE-Verlag}, address = {Berlin}, isbn = {978-3-8007-4522-7}, pages = {1 -- 10}, abstract = {Infolge neuer Zielsetzungen im Automobilbereich, wie z. B. der Weiterentwicklung von Fahrerassistenzsystemen hin zum hochautomatisierten Fahren (HAF), ergeben sich erh{\"o}hte Anforderungen an die Signalg{\"u}te der im Fahrzeug eingesetzten Inertialsensoren f{\"u}r Drehraten und Beschleunigungen. Da deren Erf{\"u}llung {\"u}ber einen hardwarebasierten Ansatz nicht immer m{\"o}glich und sinnvoll ist, strebt die Firma Continental eine Software-L{\"o}sung zur modellbasierten Verbesserung dieser Sensorsignale an.}, language = {de} } @article{Roesel, author = {R{\"o}sel, Birgit}, title = {Just-in-Time Teaching f{\"u}r einen Grundkurs Regelungstechnik - Ergebnisse und Auswirkungen der Profistufe des Zertifikats Hochschullehre}, series = {Didaktiknachrichten}, journal = {Didaktiknachrichten}, number = {06}, publisher = {Zentrum f{\"u}r Hochschuldidaktik (DiZ)}, pages = {66 -- 71}, language = {de} } @inproceedings{SchorrBoehmZentneretal., author = {Schorr, Philipp and B{\"o}hm, Valter and Zentner, Lena and Zimmermann, Klaus}, title = {Dynamical Investigation of Crawling Motion System based on a Multistable Tensegrity Structure}, series = {Proceedings of the 15th International Conference on Informatics in Control, Automation and Robotics : Porto, Portugal, 29.07.2018 - 31.07.2018}, booktitle = {Proceedings of the 15th International Conference on Informatics in Control, Automation and Robotics : Porto, Portugal, 29.07.2018 - 31.07.2018}, publisher = {SCITEPRESS}, isbn = {978-989-758-321-6}, doi = {10.5220/0006852701220130}, pages = {122 -- 130}, abstract = {The basic idea of this article is the utilization of the multistable character of a compliant tensegrity structure to control the direction of motion of a crawling motion system. A crawling motion system basing on a two-dimensional tensegrity structure with multiple stable equilibrium states is considered. This system is in contact with a horizontal plane due to gravity. For a selected harmonic actuation of the system small oscillations around the given equilibrium state of the tensegrity structure occur and the corresponding uniaxial motion of the system is evaluated. A change of the equilibrium state of the tensegrity structure yields to novel configuration of the entire system. Moreover, the motion behavior of the novel configuration is totally different although the actuation strategy is not varied. In particular, the direction of motion changes. Therefore, this approach enables a uniaxial bidirectional crawling motion with a controllable direction of motion using only one actuat or with a selected excitation frequency.}, language = {en} } @inproceedings{RoeselKoehler, author = {R{\"o}sel, Birgit and K{\"o}hler, Thomas}, title = {First results of a new digitalized concept for teaching control theory as minor subject at a university of applied science}, series = {2018 IEEE Global Engineering Education Conference (EDUCON), 17-20 April 2018, Santa Cruz de Tenerife, Spain}, booktitle = {2018 IEEE Global Engineering Education Conference (EDUCON), 17-20 April 2018, Santa Cruz de Tenerife, Spain}, publisher = {IEEE}, doi = {10.1109/EDUCON.2018.8363217}, pages = {118 -- 125}, abstract = {This paper presents a digitalized concept for teaching control theory as minor subject with an integrated approach for lectures, exercises and practical sessions and first results of the implementation at the department of electrical engineering at the OTH Regensburg. The concept uses activating methods like blended learning and possibilities of digitalization of teaching implementing Just in Time Teaching and Peer Instruction. The base of the new concept is the idea of constructive alignment. Furthermore this paper presents the feedback of the students along with an accompanying scientific research over several semesters. The data obtained from the presented module are compared with the data from other blended learning approaches in Germany.}, language = {en} } @article{SykoraDiamantidisHolickyetal., author = {S{\´y}kora, Miroslav and Diamantidis, Dimitris and Holick{\´y}, Milan and Markov{\´a}, Jana and R{\´o}zs{\´a}s, {\´A}rp{\´a}d}, title = {Assessment of compressive strength of historic masonry using non-destructive and destructive techniques}, series = {Construction and Building Materials}, volume = {193}, journal = {Construction and Building Materials}, number = {December}, publisher = {Elsevier}, doi = {10.1016/j.conbuildmat.2018.10.180}, pages = {196 -- 210}, abstract = {Masonry structures were built by various techniques using different materials, the properties of which exhibit a considerable scatter dependent on periods of construction and region-specific conditions. For historic structures with a heritage value, various non- or minor-destructive tests (NDTs) are commonly applied, while the application of destructive tests (DTs) is minimized. The contribution is based on investigations of 15 historic stone and clay brick masonry structures, for which NDT strengths of masonry units are verified by DTs. The proposed operational approach makes it possible to account for statistical uncertainty due to a limited number of DTs used to calibrate NDTs.}, language = {en} } @article{KasparRablMayer, author = {Kaspar, Marcel and Rabl, Hans-Peter and Mayer, Wolfgang}, title = {Ion-Molecule Reaction for the Selective Detection of Hydrocarbons in Diesel Exhaust Gas}, series = {Chemie Ingenieur Technik}, volume = {90}, journal = {Chemie Ingenieur Technik}, number = {6}, publisher = {WILEY-VCH}, doi = {10.1002/cite.201700075}, pages = {826 -- 834}, abstract = {The hydrocarbons present in the diesel exhaust gas are analyzed. A mass spectrometer is used for the measurements, and it operates on the basis of an ion-molecule reaction. This method is especially suitable because it is selective, is as free of fragments as possible, and is highly sensitive to the species that need to be measured. The study shows that numerous hydrocarbons in diesel exhaust gas can be identified. In particular, three molecules, ethyne, ethene and propene, were analyzed online in-depth on an engine test bench under different engine operating conditions.}, language = {en} } @article{SchorrBoehmZentneretal., author = {Schorr, Philipp and B{\"o}hm, Valter and Zentner, Lena and Zimmermann, Klaus}, title = {Motion characteristics of a vibration driven mobile tensegrity structure with multiple stable equilibrium states}, series = {Journal of Sound and Vibration}, volume = {437}, journal = {Journal of Sound and Vibration}, number = {December}, publisher = {Elsevier}, doi = {10.1016/j.jsv.2018.09.019}, pages = {198 -- 208}, abstract = {A novel type of a vibration driven motion system based on a compliant tensegrity structure with multiple stable equilibrium states is considered. These equilibrium configurations correspond to different prestress states with different dynamical properties. Therefore, the motion characteristics can be varied by changing the equilibrium state. For the application in the fields of mobile robotics, these discrete adjustable dynamics are advantageous. The vibration modes of the structure as well as the corresponding motion characteristics of the system can be adapted to the given environmental conditions in order to ensure a reliable motion. In this paper, dynamical investigations of an exemplary two-dimensional multistable tensegrity structure are considered. For the chosen parameter values the structure features two relevant equilibrium configurations. The resulting motion system is in contact to a horizontal plane due to gravity and the actuation is realized by the harmonic variation of the length of a single tensioned member. The motion of the system is simulated for various actuation frequencies with the different equilibrium states as an initial configuration. A uniaxial or a planar movement occurs depending on the selection of the actuated member within the tensegrity structure. The steady state motion is evaluated regarding motion characteristics like the steady state velocity. Moreover, the influences on the motion behavior caused by the different equilibrium states as an initial condition are emphasized. (C) 2018 Elsevier Ltd. All rights reserved.}, language = {en} } @article{daSilvaMotaHinckelRoccoetal., author = {da Silva Mota, Fabio Antonio and Hinckel, Jose Nivaldo and Rocco, Evandro Marconi and Schlingloff, Hanfried}, title = {Modeling and Analysis of a LOX/Ethanol Liquid Rocket Engine}, series = {Journal of Aerospace Technology and Management}, volume = {10}, journal = {Journal of Aerospace Technology and Management}, publisher = {Inst Aeronautica \& Espaco-IAE}, doi = {10.5028/jatm.v10.914}, abstract = {This work studies the performance and dry mass of the under development LOX/Ethanol L75 liquid rocket engine. To this end, an object-oriented program written in C++ was developed. The program is intended to be versatile and easily extensible in order to analyze different configurations of liquid rocket engines. The UML (Unified Modeling Language) tool is used to model the architecture of the codes. UML diagrams help to visualize the code structure and the communication between objects, enabling a high degree of abstraction. The cryogenics Vulcain and HM7B engines power cycles along with the staged-combustion SSME engine perform the verification of the codes. Finally, the influence of changes in design parameters on the performance and dry mass of the L75 rocket engine is analyzed.}, language = {en} } @article{BraunGebhardMatysiketal., author = {Braun, Peter and Gebhard, J{\"u}rgen and Matysik, Frank-Michael and Rabl, Hans-Peter}, title = {Potential Technical Approaches for Improving Low-Temperature NOx Conversion of Exhaust Aftertreatment Systems}, series = {Chemie Ingenieur Technik}, volume = {90}, journal = {Chemie Ingenieur Technik}, number = {6}, publisher = {WILEY-VCH}, doi = {10.1002/cite.201700122}, pages = {762 -- 773}, abstract = {Lean-burn engines, such as diesel engines, are widely used in mobile and stationary applications. Operation of lean-burn engines leads to formation of distinct amounts of nitrogen oxides (NO and NO2). Efficient aftertreatment is mandatory to meet legal requirements, especially at low exhaust temperatures, as for the future a decline of the exhaust temperature level can be predicted due to improved engine efficiencies. Within this review, potential technical solutions to enhance the DeNO(x)-aftertreatment efficiency at low exhaust temperatures are presented.}, language = {en} } @article{BarzSeligerMarxetal., author = {Barz, Tilman and Seliger, Dominik and Marx, Klemens and Sommer, Andreas and Walter, Sebastian F. and Bock, Hans Georg and Koerkel, Stefan}, title = {State and state of charge estimation for a latent heat storage}, series = {Control Engineering Practice}, volume = {72}, journal = {Control Engineering Practice}, publisher = {Pergamon-Elsevier d.}, doi = {10.1016/j.conengprac.2017.11.006}, pages = {151 -- 166}, abstract = {A nonlinear state observer is designed for a thermal energy storage with solid/liquid phase change material (PCM). Using a physical 2D dynamic model, the observer reconstructs transient spatial temperature fields inside the storage and estimates the stored energy and the state of charge. The observer has been successfully tested with a lab-scale latent heat storage with a single pass tube bundle and the phase change material located in a shell around each tube. It turns out that the observer robustly tracks the real process data with as few as four internal PCM temperature sensors. © 2017 Elsevier Ltd. All rights reserved.}, language = {en} } @article{daSilvaMotaHinckelRoccoetal., author = {da Silva Mota, Fabio Antonio and Hinckel, Jose Nivaldo and Rocco, Evandro Marconi and Schlingloff, Hanfried}, title = {Trajectory Optimization of Launch Vehicles Using Object-oriented Programming}, series = {Journal of aerospace technology and management}, volume = {10}, journal = {Journal of aerospace technology and management}, publisher = {Institute of Aeronautics and Space}, doi = {10.5028/jatm.v10.948}, abstract = {The aim of this study is to model launch vehicles with focus on 3-DOF trajectory optimization using a modular approach. Despite the large number of operational launch vehicles, they usually consist of basic components and subsystems. In other words, a launch vehicle is an assembly of stages, which in turn is divided into propellant system and engine, and the engine is an assembly of basic components such as pumps, turbines, combustion chamber, and nozzle. To allow future extension and reuse of the codes, a modular structure using object-oriented programming is used. Two formulations of state equations of the trajectory and two optimization methods are described. The launch vehicle performance will be measured by payload mass for a given mission. The simulations of the VLS-1, Ariane 5 and VLS-Alfa were performed and showed good agreement with the literature.}, language = {en} } @article{GaertnerRablZink, author = {G{\"a}rtner, Uwe and Rabl, Hans-Peter and Zink, Uwe}, title = {Exhaust Gas Aftertreatment of the Future}, series = {MTZ worldwide}, volume = {79}, journal = {MTZ worldwide}, number = {7-8}, publisher = {Springer}, doi = {10.1007/s38313-018-0060-2}, pages = {70 -- 75}, language = {en} } @article{SchuemannMorichKaufholdetal., author = {Sch{\"u}mann, Malte and Morich, J. and Kaufhold, Tobias and B{\"o}hm, Valter and Zimmermann, Klaus and Odenbach, Stefan}, title = {A mechanical characterisation on multiple timescales of electroconductive magnetorheological elastomers}, series = {Magnetism and Magnetic Materials}, volume = {453}, journal = {Magnetism and Magnetic Materials}, number = {May}, publisher = {Elsevier}, doi = {10.1016/j.jmmm.2018.01.029}, pages = {198 -- 205}, abstract = {Magnetorheological elastomers are a type of smart hybrid material which combines elastic properties of a soft elastomer matrix with magnetic properties of magnetic micro particles. This leads to a material with magnetically controllable mechanical properties of which the magnetorheological effect is the best known. The addition of electroconductive particles to the polymer mix adds electrical properties to the material behaviour. The resulting electrical resistance of the sample can be manipulated by external magnetic fields and mechanical loads. This results in a distinct interplay of mechanical, electrical and magnetic effects with a highly complex time behaviour. In this paper a mechanical characterisation on multiple time scales was conducted to get an insight on the short and long-term electrical and mechanical behaviour of this novel material. The results show a complex resistivity behaviour on several timescales, sensitive to magnetic fields and strain velocity. The observed material exhibits fatigue and relaxation behaviour, whereas the magnetorheological effect appears not to interfere with the piezoresistive properties.}, language = {en} } @inproceedings{HacklHirschbergLexetal., author = {Hackl, Andreas and Hirschberg, Wolfgang and Lex, Cornelia and Rill, Georg}, title = {Tyre type dependent transient force behaviour by means of a maxwell model}, series = {The Dynamics of Vehicles on Roads and Tracks : Proceedings of the 25th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2017), Rockhampton, Queensland, Australia, 14-18 August 2017}, booktitle = {The Dynamics of Vehicles on Roads and Tracks : Proceedings of the 25th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2017), Rockhampton, Queensland, Australia, 14-18 August 2017}, editor = {Spiryagin, Maksym and Gordon, Timothy and Cole, Colin and McSweeney, Tim}, publisher = {CRC Press}, address = {London}, isbn = {1351057170}, doi = {10.1201/9781315265506}, pages = {157 -- 162}, abstract = {The present papers deals with the usability of an extended Maxwell model to describe the tyre dynamics during transient driving manoeuvres. In the present article, the para-metrisation process of a dynamic tyre model is investigated in a first step, using measurement data of tyre forces from a flat trac tyre test bench, (IABG 2016). Two tyre types of dimensions 255/50 R19 and 175/55 R15 are used. The practical applicability is discussed, considering the measurement procedure and the parameter optimisation process. In a second step, the performance of the dynamic tyre model is validated using measurements of manoeuvres under higher dynamic excitation. As a last step, an outlook is given on further research planned in which the presented model and parametrisation are adapted to a larger frequency range.}, language = {en} } @inproceedings{BresinskyReusner, author = {Bresinsky, Markus and Reusner, Florian}, title = {GLOBE - Learn and Innovate Digitization by a Virtual Collaboration Exercise and Living Lab}, series = {Interactivity, Game Creation, Design, Learning, and Innovation. 6th International Conference, ArtsIT 2017, and Second International Conference, DLI 2017, Heraklion, Crete, Greece, October 30-31, 2017, Proceedings}, booktitle = {Interactivity, Game Creation, Design, Learning, and Innovation. 6th International Conference, ArtsIT 2017, and Second International Conference, DLI 2017, Heraklion, Crete, Greece, October 30-31, 2017, Proceedings}, publisher = {Springer Nature}, doi = {10.1007/978-3-319-76908-0_26}, pages = {273 -- 281}, abstract = {This paper presents an advanced interactive learning platform .dot that implements the GLOBE exercise, using innovative information and communication technologies to enhance learning and development of management and leadership skills in a complex organizational setting. GLOBE on the one hand focuses on competences around ICT and virtual collaboration, and on the other hand on digital transformation, technologies and tools at higher education institutions. By this applied science, learning and developing on the real-world platform, analysis and drive of digital innovation and transformation can be fostered. The main goal is to co-create knowledge and solutions in the following focused subjects: Management and leadership of multidisciplinary, multinational and multicultural virtual and real collaboration in a complex organizational environment. GLOBE uses real world scenarios (e.g. United Nations mission) and involves real world actors. This comprehensive educational approach should enhance learning techniques and leverage learning progress with hands-on experiences and applied science in the context of ICT and virtual collaboration, and the embodied dynamics of behavior to support innovation and development.}, language = {en} } @inproceedings{KoderZacherlRabletal., author = {Koder, Alexander and Zacherl, Florian and Rabl, Hans-Peter and Mayer, Wolfgang and Gruber, Georg and Dotzer, Thomas}, title = {Jatropha Oil as an Alternative Fuel for Modern Diesel Engines - Injection Characteristics and EGR-Compatibility}, series = {WCX 17: SAE World Congress 2017}, booktitle = {WCX 17: SAE World Congress 2017}, publisher = {SAE International}, doi = {10.4271/2017-01-5000}, abstract = {An effective way to reduce greenhouse gas emissions (GHGs) is to use rurally produced straight jatropha oil as a substitute for diesel fuel. However, the different physical and chemical properties of straight vegetable oils (SVOs) require a customized setup of the combustion engine, particularly of the injection timing and quantity. Therefore, this study demonstrates the differences in the injection and combustion processes of jatropha oil compared to diesel fuel, particularly in terms of its compatibility with exhaust gas recirculation (EGR). A 2.2 l common-rail diesel engine with a two-stage turbocharging concept was used for testing. To examine the differences in injection rate shaping of diesel fuel and jatropha oil, the injector was tested with an injection rate analyzer using both the fuels. To investigate the combustion process, the engine was mounted at an engine test bench and equipped with a cylinder pressure indication system. All limited emissions, as well as fuel consumption, were measured. Various injection strategies, boost and rail pressure levels were tested at different EGR rates in terms of their impact on the combustion process. EGR in particular offers a great potential in the case of jatropha oil combustion due to its oxygen content. In addition, the investigation of injection rate shaping in combination with cylinder pressure analysis allowed a detailed thermodynamic evaluation of the combustion process. Ignition delay (ID) was also analyzed using a new method to calculate the start of combustion (SOC)}, language = {en} } @incollection{SoergelRiedererHeldetal., author = {S{\"o}rgel, Matthias and Riederer, Michael and Held, Andreas and Plake, Daniel and Zhu, Zhilin and Foken, Thomas and Meixner, Franz X.}, title = {Trace Gas Exchange at the Forest Floor}, series = {Energy and Matter Fluxes of a Spruce Forest Ecosystem}, volume = {229}, booktitle = {Energy and Matter Fluxes of a Spruce Forest Ecosystem}, editor = {Foken, Thomas}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-49387-9}, doi = {10.1007/978-3-319-49389-3_8}, pages = {157 -- 179}, abstract = {Exchange conditions at the forest floor are complex due to the heterogeneity of sources and sinks and the inhomogeneous radiation but are important for linking soil respiration to measurements in the trunk space or above canopy. Far more attention has therefore been paid to above and within canopy flows, but even studies that addressed forest floor exchange do not present measurements below 1 m or 2 m. We used a multilayer model that explicitly resolves the laminar layer, the buffer layer, and the turbulent layer to calculate fluxes from the measured profiles in the lowest meter above ground and to calculate effective surface concentrations from given fluxes. The calculated fluxes were compared to measured eddy covariance fluxes of sensible heat and O3 and to chamber derived soil fluxes of CO2 and 222Rn. Sensible heat fluxes agreed surprisingly well given the heterogeneity of radiative heating and the generally low fluxes (max. 25 W m-2). The chamber fluxes turned out to be not comparable as the chamber fluxes were too low, probably due to one of the well-known problems of enclosures such as pressure differences, disturbed gradients and exclusion of naturally occurring turbulence events and surface cooling. The O3 fluxes agreed well for high O3 values reaching down to the forest floor during full coupling of the canopy by coherent structures. During most of the time, the model overestimated the fluxes as chemical reactions were dominating within the profile. One new approach was to calculate the effective surface concentration from a given flux and compare this to measured surface concentrations. This allowed the identification of situations with a coupled and decoupled forest floor layer, which has important consequences for respiration measurements in the trunk space or above canopy and should be considered in upcoming studies.}, language = {en} } @book{OPUS4-4015, title = {Energiespeicher - Bedarf, Technologien, Integration}, editor = {Sterner, Michael and Stadler, Ingo}, edition = {2. korrigierte und erg{\"a}nzte Auflage}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-662-48892-8}, doi = {10.1007/978-3-662-48893-5}, abstract = {Die Autoren dieses Werkes geben einen umfassenden {\"U}berblick {\"u}ber die verschiedenen Aspekte der Energiespeicherung. Sie beschreiben zun{\"a}chst die Bedeutung von Energiespeichern in der Energieversorgung und definieren ihre Rolle darin. Dann gehen sie auf den Speicherbedarf in der Strom-, W{\"a}rme- und Kraftstoffversorgung im Kontext der Energiewende ein. Im Hauptteil werden die verschiedenen Speichertechnologien ausf{\"u}hrlich vorgestellt sowie ihre Vor- und Nachteile diskutiert. Praktische Anwendungsbeispiele und die Integration von Speichern {\"u}ber alle Energiesektoren hinweg runden das Buch ab. Zahlreiche Grafiken und Beispiele veranschaulichen das gesamte Feld der Energiespeicher und sind als Erg{\"a}nzung mehrsprachig online in Farbe verf{\"u}gbar. Die 2. Auflage enth{\"a}lt ein neues Kapitel zu den rechtlichen Rahmenbedingungen, neue Studien zum Speicherbedarf, Power-to-X f{\"u}r die chemische Industrie, neue LOHC- und Lageenergiespeicher sowie neueste Trends zu Kostenentwicklung und Batterieanwendungen. „Endlich ein umfassendes Buch zur Energiewende, das auch f{\"u}r technische Laien verst{\"a}ndlich und inspirierend geschrieben ist." Franz Alt, Journalist und Buchautor „Das großartige Werk sei allen empfohlen, die sich wirklich f{\"u}r die Zukunft unseres Landes interessieren. Es zeigt auf eindrucksvolle Weise: Es wird nicht einfach, aber wir schaffen das." Prof. Dr. Harald Lesch, Physiker und Fernsehmoderator}, language = {de} } @incollection{Sterner, author = {Sterner, Michael}, title = {Power-to-Gas}, series = {Handbook of Climate Change Mitigation and Adaptation}, booktitle = {Handbook of Climate Change Mitigation and Adaptation}, editor = {Chen, Wei-Yin and Suzuki, Toshio and Lackner, Maximilian}, edition = {2}, publisher = {Springer VS}, address = {Cham}, isbn = {978-3-319-14408-5}, doi = {10.1007/978-3-319-14409-2_89}, pages = {2775 -- 2825}, abstract = {This chapter provides an overview on the storage technology power-to-gas for the decarbonization of all energy sectors. Other than "negative emissions" with CCS or biomass, which have clear limits in potentials, costs and environmental benefits, storage and energy conversion technologies like power-to-gas and power-to-x enable the decarbonization by neutralizing the CO2 footprint of all energy services. Via the conversion of renewable electricity into chemical energy carriers like renewable hydrogen or renewable hydrocarbons, the existing fossil infrastructure with vast and sufficient storage and transport capacities can be used with carbon neutral renewable energy. After showing the demand for storage technologies, the technology components of power-to-gas are described, building the basis for the storage system power-to-gas itself that is described in detail, including efficiency, potential, CO2 emissions, and costs. In conclusion, a technical pathway of decarbonization including costs is described for the industrial nation of Germany and necessary policy frameworks are derived.}, language = {en} } @incollection{SternerThema, author = {Sterner, Michael and Thema, Martin}, title = {Vergleich der Speichersysteme}, series = {Energiespeicher - Bedarf, Technologien, Integration}, booktitle = {Energiespeicher - Bedarf, Technologien, Integration}, edition = {2. Auflage}, publisher = {Springer Vieweg}, address = {Berlin ; Heidelberg}, isbn = {978-3-662-48893-5}, doi = {10.1007/978-3-662-48893-5_12}, pages = {645 -- 682}, subject = {Energiespeicher}, language = {de} } @incollection{SternerStadlerEckertetal., author = {Sterner, Michael and Stadler, Ingo and Eckert, Fabian and Gerhardt, Norman and von Olshausen, Christian and Thema, Martin and Trost, Tobias}, title = {Speicherintegration zur Kopplung unterschiedlicher Energiesektoren}, series = {Energiespeicher - Bedarf, Technologien, Integration}, booktitle = {Energiespeicher - Bedarf, Technologien, Integration}, edition = {2. Auflage}, publisher = {Springer Vieweg}, address = {Berlin ; Heidelberg}, isbn = {978-3-662-48893-5}, doi = {10.1007/978-3-662-48893-5_14}, pages = {769 -- 818}, subject = {Energieversorgung}, language = {de} } @incollection{SternerBreuerDreesetal., author = {Sterner, Michael and Breuer, Christopher and Drees, Tim and Eckert, Fabian and Maaz, Andreas and Pape, Carsten and Rotering, Niklas and Thema, Martin}, title = {Speicherbedarf in der Stromversorgung}, series = {Energiespeicher - Bedarf, Technologien, Integration}, booktitle = {Energiespeicher - Bedarf, Technologien, Integration}, edition = {2. Auflage}, publisher = {Springer Vieweg}, address = {Berlin ; Heidelberg}, isbn = {978-3-662-48893-5}, doi = {10.1007/978-3-662-48893-5_3}, pages = {53 -- 140}, subject = {Speicherbedarf}, language = {de} } @incollection{SternerEckertGerhardtetal., author = {Sterner, Michael and Eckert, Fabian and Gerhardt, Norman and Henning, Hans-Martin and Palzer, Andreas}, title = {Speicherbedarf in der W{\"a}rmeversorgung}, series = {Energiespeicher - Bedarf, Technologien, Integration}, booktitle = {Energiespeicher - Bedarf, Technologien, Integration}, edition = {2. Auflage}, publisher = {Springer Vieweg}, address = {Berlin ; Heidelberg}, isbn = {978-3-662-48893-5}, doi = {10.1007/978-3-662-48893-5_4}, pages = {141 -- 168}, subject = {Energiespeicher}, language = {de} } @incollection{SternerStadlerEckertetal., author = {Sterner, Michael and Stadler, Ingo and Eckert, Fabian and Thema, Martin}, title = {Speicherintegration in einzelnen Energiesektoren}, series = {Energiespeicher - Bedarf, Technologien, Integration}, booktitle = {Energiespeicher - Bedarf, Technologien, Integration}, edition = {2. Auflage}, publisher = {Springer Vieweg}, address = {Berlin ; Heidelberg}, isbn = {978-3-662-48893-5}, doi = {10.1007/978-3-662-48893-5_13}, pages = {685 -- 767}, subject = {Energiespeicher}, language = {de} }