@article{FreniFrazzicaDawoudetal., author = {Freni, Angelo and Frazzica, Andrea and Dawoud, Belal and Chmielewski, Stefanie and Calabrese, Luigi and Bonaccorsi, Lucio Maria}, title = {Adsorbent coatings for heat pumping applications: Verification of hydrothermal and mechanical stabilities}, series = {Applied Thermal Engineering}, volume = {50}, journal = {Applied Thermal Engineering}, number = {2}, publisher = {Elsevier}, doi = {10.1016/j.applthermaleng.2011.07.010}, pages = {1658 -- 1663}, abstract = {This paper presents novel experimental methods for verification of both hydrothermal and mechanical stabilities of adsorbent coatings. Experiments have been carried out on zeolite-based coatings over aluminum substrates, prepared by a dip-coating technique developed at CNR-ITAE. Hydrothermal aging of several adsorbent coatings is ongoing. Adsorption and structural stability of some samples under test was successfully verified after 35000 aging cycles by isobars measurement and XRD analysis. Mechanical properties of coatings have been evaluated by applying different typologies of static and dynamic mechanical stresses. Results obtained have been compared with those achieved by subjecting adsorbent coatings prepared by Mitsubishi Plastic Incorporation (MPI) to the same characterization protocol. The comparison between the two types of coating returned that MPI coatings posses similar thermal stability and better mechanical strength than CNR-ITAE coatings.}, language = {en} } @article{FrazzicaPalombaDawoudetal., author = {Frazzica, Andrea and Palomba, Valeria and Dawoud, Belal and Gull{\`i}, Giuseppe and Brancato, Vincenza and Sapienza, Alessio and Vasta, Salvatore and Freni, Angelo and Costa, Fabio and Restuccia, Giovanni}, title = {Design, realization and testing of an adsorption refrigerator based on activated carbon/ethanol working pair}, series = {Applied Energy}, volume = {174}, journal = {Applied Energy}, publisher = {Elsevier}, doi = {10.1016/j.apenergy.2016.04.080}, pages = {15 -- 24}, abstract = {In the present paper design, realization and testing of a novel small scale adsorption refrigerator prototype based on activated carbon/ethanol working pair is described. Firstly, experimental activity has been carried out for identification of the best performing activated carbon available on the market, through the evaluation of the achievable thermodynamic performance both under air conditioning and refrigeration conditions. Once identified the best performing activated carbon, the design of the adsorber was developed by experimental dynamic performance analysis, carried out by means of the Gravimetric-Large Temperature Jump (G-LTJ) apparatus available at CNR ITAE lab. Finally, the whole 0.5 kW refrigerator prototype was designed and built. First experimental results both under reference air conditioning and refrigeration cycles have been reported, to check the achievable performance. High Specific Cooling Powers (SCPs), 95 W/kg and 50 W/kg, for air conditioning and refrigeration respectively, were obtained, while the COP ranged between 0.09 and 0.11, thus showing an improvement of the current state of the art. (C) 2016 Elsevier Ltd. All rights reserved.}, language = {en} } @article{KalitaSnarskiiShamoninChamonineetal., author = {Kalita, Viktor M. and Snarskii, Andrei A. and Shamonin (Chamonine), Mikhail and Zorinets, Denis}, title = {Effect of single-particle magnetostriction on the shear modulus of compliant magnetoactive elastomers}, series = {Physical review E}, volume = {95}, journal = {Physical review E}, number = {3}, publisher = {American Physical Society}, doi = {10.1103/PhysRevE.95.032503}, abstract = {The influence of an external magnetic field on the static shear strain and the effective shear modulus of a magnetoactive elastomer (MAE) is studied theoretically in the framework of a recently introduced approach to the single-particle magnetostriction mechanism [V. M. Kalita et al., Phys. Rev. E 93, 062503 (2016)]. The planar problem of magnetostriction in an MAE with magnetically soft inclusions in the form of a thin disk (platelet) having the magnetic anisotropy in the plane of this disk is solved analytically. An external magnetic field acts with torques on magnetic filler particles, creates mechanical stresses in the vicinity of inclusions, induces shear strain, and increases the effective shear modulus of these composite materials. It is shown that the largest effect of the magnetic field on the effective shear modulus should be expected in MAEs with soft elastomer matrices, where the shear modulus of the matrix is less than the magnetic anisotropy constant of inclusions. It is derived that the effective shear modulus is nonlinearly dependent on the external magnetic field and approaches the saturation value in magnetic fields exceeding the field of particle anisotropy. It is shown that model calculations of the effective shear modulus correspond to a phenomenological definition of effective elastic moduli and magnetoelastic coupling constants. The obtained theoretical results compare well with known experimental data. Determination of effective elastic coefficients in MAEs and their dependence on magnetic field is discussed. The concentration dependence of the effective shear modulus at higher filler concentrations has been estimated using the method of Pade approximants, which predicts that both the absolute and relative changes of the magnetic-field-dependent effective shear modulus will significantly increase with the growing concentration of filler particles.}, language = {en} } @article{BruniMeijaardRilletal., author = {Bruni, S. and Meijaard, J. P. and Rill, Georg and Schwab, A. L.}, title = {State-of-the-art and challenges of railway and road vehicle dynamics with multibody dynamics approaches}, series = {Multibody System Dynamics}, volume = {49}, journal = {Multibody System Dynamics}, number = {1}, publisher = {Springer}, doi = {10.1007/s11044-020-09735-z}, pages = {1 -- 32}, abstract = {A review of the current use of multibody dynamics methods in the analysis of the dynamics of vehicles is given. Railway vehicle dynamics as well as road vehicle dynamics are considered, where for the latter the dynamics of cars and trucks and the dynamics of single-track vehicles, in particular motorcycles and bicycles, are reviewed. Commonalities and differences are shown, and open questions and challenges are given as directions for further research in this field.}, language = {en} } @article{SchwanzerRablLodersetal., author = {Schwanzer, Peter and Rabl, Hans-Peter and Loders, S. and Seifert, P. and Himmelstoss, S. and Gaderer, Matthias}, title = {Difference in the Tailpipe Particle Number by Consideration of Sub-23-nm Particles for Different Injection Settings of a GDI Engine}, series = {Emission control science and technology}, volume = {5}, journal = {Emission control science and technology}, number = {1}, publisher = {Springer Nature}, doi = {10.1007/s40825-019-0114-1}, pages = {7 -- 22}, abstract = {The purpose of this study was to investigate the characteristic of nanoparticles under consideration of sub-23-nm particles from a 1.8-l direct injection (DI) gasoline engine under stoichiometric air/fuel conditions in the exhaust gas system. For future CO2 challenges, the usage of DI-instead of port fuel injection (PFI)-gasoline engines is unavoidable. Therefore, a state of the art particle management program-particle number (PN) system, the Horiba SPCS (2100) with an integrated CPC (condensation particle counter), was recalibrated from a 50\% cutoff (D-50\%) at 23 nm down to a cutoff at 10 nm and the PCRF (particle concentration reduction factor) for sizes smaller than 23 nm was checked. Two different modal points, out of a representative Real Driving Emission (RDE) cycle, were investigated with both calibrations, D-50\%=10 nm and D-50\%=23 nm. For these different load points, the fuel pressure (FUP) and the start of injection (SOI) were varied, to represent the difference in the structure and the ratio conc((10 nm))/conc((23 nm)) of the nanoparticle emissions. The particle characterization includes the particle number (PN), the particle size distribution (PSD), and the particle mass (PM). The particle number was measured with Horiba SPCS (2100). The particle size distribution was analyzed with a Grimm differential mobility analyzer (DMA) in combination with a Faraday cup electrometer (FCE). Micro Soot and Pegasor were used to determine the PM, and an optical characterization was done with a 120-kV Phillips CM12 transmission electron microscope (TEM). The position of all particle measurement systems was downstream the three-way catalyst (TWC). The results of this investigation showed that a higher injection pressure decreases the PN (without consideration of sub-23-nm particles) in general. The ratio conc((10 nm))/conc((23 nm)) was therefore higher, because smaller particles, especially ash particles, were less reduced from the FUP. This means higher FUP tends to a higher ratio. For the SOI, the main reasons of the ratio differences were explained by an encroachment between the injection jet and the piston, the valve and the wall.}, language = {en} } @article{SchwanzerSchillingerMieslingeretal., author = {Schwanzer, Peter and Schillinger, Maximilian and Mieslinger, Johann and Walter, Stefanie and Hagen, Gunter and Maerkl, Susanne and Haft, Gerhard and Dietrich, Markus and Moos, Ralf and Gaderer, Matthias and Rabl, Hans-Peter}, title = {A Synthetic Ash-Loading Method for Gasoline Particulate Filters with Active Oil Injection}, series = {SAR International Journal of Engines}, volume = {14}, journal = {SAR International Journal of Engines}, number = {4}, publisher = {SAE International}, issn = {1946-3936}, doi = {10.4271/03-14-04-0029}, pages = {493 -- 506}, abstract = {To reduce particulate emissions, the use of particulate filters in diesel engines is meanwhile state of the art, while the integration of such systems in gasoline engines is now also necessary in order to comply with today's regulations. Over its lifetime, a gasoline particulate filter (GPF) collects ash components of fuel, lubrication oil, and materials originating from the catalytic coating and from engine abrasion. In the development and application process, synthetic ashing from GPFs is challenging. The ash of the lubrication oil can be increased in various ways, like oil-doped fuel, a separate oil burner, or changes in the piston-cylinder system of the engine. However, these methods show major disadvantages. For this reason, an improved approach is presented in this study, which allows a quick response to changes in combustion (e.g., engine knocking) and producing ash, which is more realistic due to its primary particle size and the density of ash plugs, in a shorter time. Therefore, an approach to accelerate ash loading by active oil injection using a multi-point injection (MPI) system is introduced. With the help of this methodology, an ashing capacity of 1.21 g/h is implemented, which is a high rate compared to other investigations. The primary particle size (evaluated by means of a transmission electron microscope), is in the same size range as those detected at the full-load curve during regular operation. A computer tomographic (CT) analysis of the incinerated particulate filter also shows that a very high density of ash plugs can be realized, which has also been found in the literature for real applications. In addition, with the help of a mass spectrometer (MS) and an intermediate weighing of the particulate filter, the current ash loading of the GPF could be determined with an accuracy of 1\%.}, language = {en} } @article{SchorrZentnerZimmermannetal., author = {Schorr, Philipp and Zentner, Lena and Zimmermann, Klaus and B{\"o}hm, Valter}, title = {Jumping locomotion system based on a multistable tensegrity structure}, series = {Mechanical systems and signal processing}, journal = {Mechanical systems and signal processing}, number = {152}, publisher = {Elsevier}, doi = {10.1016/j.ymssp.2020.107384}, abstract = {All known locomotion principles are limited respective to environmental conditions. Often, the occurrence of obstacles or gaps means the break-off for the operating motion systems. For such circumstances, a controllable jumping locomotion is required to cross these barriers. However, this locomotion demands sophisticated requirements to the actuation. The abrupt actuation is commonly realized by high dynamic actuators or complex mechanisms. In this work, a simple solution utilizing the multistability of a compliant tensegrity structure is described. Therefore, a two-dimensional tensegrity structure featuring four stable equilibria is considered. Based on bifurcation analyses a feasible actuation to control the current equilibrium configuration is derived. Changing between selected equilibrium states enables a great difference in potential energy, which yields a jumping motion of the structure. Based on numerical simulations a suitable actuation strategy is chosen to overcome obstacle and steps by jumping forward or backward, respectively. The theoretical approach is examined experimentally with a prototype of the multistable tensegrity structure. (c) 2020 Elsevier Ltd. All rights reserved. All known locomotion principles are limited respective to environmental conditions. Often, the occurrence of obstacles or gaps means the break-off for the operating motion systems. For such circumstances, a controllable jumping locomotion is required to cross these barriers. However, this locomotion demands sophisticated requirements to the actuation. The abrupt actuation is commonly realized by high dynamic actuators or complex mechanisms. In this work, a simple solution utilizing the multistability of a compliant tensegrity structure is described. Therefore, a two-dimensional tensegrity structure featuring four stable equilibria is considered. Based on bifurcation analyses a feasible actuation to control the current equilibrium configuration is derived. Changing between selected equilibrium states enables a great difference in potential energy, which yields a jumping motion of the structure. Based on numerical simulations a suitable actuation strategy is chosen to overcome obstacle and steps by jumping forward or backward, respectively. The theoretical approach is examined experimentally with a prototype of the multistable tensegrity structure.}, language = {en} } @article{SindersbergerPremMonkman, author = {Sindersberger, Dirk and Prem, Nina and Monkman, Gareth J.}, title = {Self-assembling structure formation in low-density magnetoactive polymers}, series = {Journal of Applied Polymer Science}, volume = {137}, journal = {Journal of Applied Polymer Science}, number = {3}, publisher = {Wiley}, doi = {10.1002/app.48291}, abstract = {The formation of microstructures in magnetoactive polymers (MAPs) is a recently discovered phenomenon found only with very low filler particle concentrations (less than 3 wt \%). Due to the degassing process, filler particles collect around an ascending bubble, which dissolves at a certain point leaving particulate rings within the matrix. The formation of toroidal microstructures commences as filler concentration approaches 1 wt \%. The development of coherent parallel aligned rings with a compact order continues as particle concentrations increase toward 2 wt \%. Between 2 and 3 wt \% capillary doublets develop, while mass percentages higher than 3\% result in increasing entropy as the random order of particle agglomeration found in higher concentration MAP dominates. Self-structured samples of different filler material and concentrations between 1 and 3 wt \% have been investigated using X-ray tomography, where the emerging structures can be observed and visualized. The ring structures resulting from this research represent microinductivities which can be fabricated in a targeted manner, thus enabling new applications in the high-frequency radio field. Furthermore, these anisotropic, but well-organized, structures have magnetic field-dependent implications for optical, thermal, acoustic, and medical applications.}, language = {en} } @article{SchulzSchwarz, author = {Schulz, Carsten and Schwarz, Colin}, title = {Drivetrain fatigue strength characteristics of model-predictive control for wind turbines}, series = {Wind Energy}, volume = {23}, journal = {Wind Energy}, number = {12}, publisher = {Wiley}, doi = {10.1002/we.2520}, pages = {2137 -- 2149}, abstract = {Wind turbines play a crucial role in the revolution towards renewable resources. They need to be economically competitive to be sustainable. This still requires to lower the cost of energy (COE). To this end, nonlinear model predictive control (NMPC) is used within this paper. As known from literature, NMPC significantly improves the energy extracting performance as well as the mitigation of tower loads of wind turbines. As it is shown in this paper, the drivetrain fatigue strength drops disproportionally in parallel, which either increases the demands on the turbine design or decreases the lifetime of drivetrain components. Without additional boundary conditions to the underlying optimal control problems (OCPs), the application of energy-maximizing NMPC might so even raise the COE. Only penalizing axial torque oscillations by quadratic terms decreases energy-extracting performance below the level of classical wind turbine controllers. This makes more sophisticated conditions necessary. In this paper, the increase of the drivetrain damage by NMPC is analyzed, and appropriate boundary conditions are derived, to balance the two contradicting objectives of energy maximization and drivetrain load mitigation. An NMPC approach based on indirect methods is used, to obtain a solution of the OCPs very efficiently. It applies the Hamilton equations and Pontryagin's maximum principle. Its accuracy and efficiency to solve OCPs was presented over the last decades.}, language = {en} } @inproceedings{BogomolovKralHaumeretal., author = {Bogomolov, Maxim and Kral, Christian and Haumer, Anton and Lomonova, Elena}, title = {Modeling of permanent magnet synchronous machine with fractional slot windings}, series = {Proceedings IECON 2012 - 38th Annual Conference on IEEE Industrial Electronics Society ; Ecole de Technologie Superieure de Montreal, Universite du Quebec Montreal, Canada 25 - 28 October, 2012}, booktitle = {Proceedings IECON 2012 - 38th Annual Conference on IEEE Industrial Electronics Society ; Ecole de Technologie Superieure de Montreal, Universite du Quebec Montreal, Canada 25 - 28 October, 2012}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-4673-2421-2}, issn = {1553-572X}, doi = {10.1109/IECON.2012.6388912}, pages = {1894 -- 1899}, abstract = {This paper focuses on simulation of permanent magnet synchronous machine (PMSM) with fractional-slot windings (FSW) in Modelica. Modeling of the electrical machines with object-oriented approach is shortly described, and a new Modelica library for simulation of electrical machines is introduced. The results of simulation of PMSMs with fractional slot windings are presented and explained. Special attention is paid to the higher harmonics and subharmonics produced by the winding and their influence on machine operation.}, language = {en} } @inproceedings{ReindlSingerMeieretal., author = {Reindl, Andrea and Singer, Thomas and Meier, Hans and Niemetz, Michael and Park, Sangyoung}, title = {Framework to Test DC-DC Converters Developed for a Decentralized Battery Management System}, series = {2021 International Conference on Applied Electronics (AE): 7-8 Sept. 2021, Pilsen, Czech Republic}, booktitle = {2021 International Conference on Applied Electronics (AE): 7-8 Sept. 2021, Pilsen, Czech Republic}, publisher = {IEEE}, doi = {10.23919/AE51540.2021.9542882}, pages = {1 -- 6}, abstract = {DC- DC converters control the power flow and thus the power distribution between the components on different voltage levels. They are essential for (dis)charging batteries and influence the safety and stability of the entire battery management system (BMS). Therefore, testing the functionality and the reliability of DC-DC converters is crucial. This is especially true for decentralized battery management systems (DBMS), where multiple nodes communicate to collectively control the system. The used DC-DC converters are modified to parameterize them during operation via microcontroller interfaces. Integrating the communication into the control loop requires an analysis of the control behavior due to additional delays. Therefore, this paper proposes a framework to test DC-DC converters considering the control and communication perspectives. The response time, the control accuracy and stability of these DC-DC converters, e.g., under continuous and abrupt load changes, are measured in automated tests. The dedicated software framework simulates the DBMS and stimulates the hardware components (e.g. electronic loads, data acquisition) via respective interfaces (CAN, RS232). This allows the test of various DC-DC converters with flexibly adaptable load and power generation profiles. An initial application validates the test framework by verifying the aforementioned aspects and thus the applicability of a DC-DC converter within the DBMS.}, language = {en} } @inproceedings{BrkicCeranElmoghazyetal., author = {Brkic, Jovan and Ceran, Muaz and Elmoghazy, Mohamed and Kavlak, Ramazan and Haumer, Anton and Kral, Christian}, title = {Open Source PhotoVoltaics Library for Systemic Investigations}, series = {Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany}, booktitle = {Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany}, publisher = {Link{\"o}ing University Electronic Press}, doi = {10.3384/ecp1915741}, pages = {41 -- 50}, abstract = {For the planning of photovoltaic power plants standard software tools are used. Most of these software tools use statistical solar data to determine the overall energy harvest of a photovoltaic plant over one year. The calculations rely on stationary location and ideal boundary conditions, e.g., constant ambient temperature. Even though, for example, shadowing may be considered by standard software, the investigation of untypical configurations and problems cannot be performed by such software, as most configurations cannot be changed by the user. The presented PhotoVoltaics library was developed with the intention to provide a flexible framework for standard and non-standard problems. Particularly, the PhotoVoltaics library can be coupled with other Modelica libraries to perform systemic investigations. An application library, PhotoVoltaics_TGM, is provided as add-on, where measured data of two photovoltaic pants of the TGM in Vienna can be compared with simulation results. This add-on library serves as validation of the PhotoVoltaics library.}, language = {en} } @inproceedings{ScharfenbergElisHofmann, author = {Scharfenberg, Georg and Elis, Ludek and Hofmann, Gerhard}, title = {New Design Methodology - Using VHDL-AMS Models to Consider Aging Effects in Automotive Mechatronic Circuits for Safety Relevant Functions}, series = {2019 International Conference on Applied Electronics (AE), 10-11 Sept. 2019, Pilsen, Czech Republic}, booktitle = {2019 International Conference on Applied Electronics (AE), 10-11 Sept. 2019, Pilsen, Czech Republic}, doi = {10.23919/AE.2019.8867034}, pages = {1 -- 5}, abstract = {In this paper a design method for mechatronic functions in an early design phase under consideration of the requirements of functional safety is proposed [14]. The goal of the method is to discover threats for the safety goals and to prove or optimize the diagnostic mechanisms. At the current design process a lifetime endurance test is performed in a late project phase. In order to avoid unexpected late design changes the method should be applied in an early design phase. The method is an additional way to avoid design failures for E/E functions with special focus on aging in the field of functional safety applications. The method is developed out of three standards VDI 2221 methodology for development and construction of technical systems and products [1]), VDI 2206 design methodology for mechatronic systems [2] and the ISO 26262 road vehicles - Functional Safety [3] by using the V-Model. Furthermore, a core element of the design method is simulating aging effects by applying VHDL - AMS. To demonstrate the design methodology a sensor out of the EGAS function is chosen as a safety relevant automotive system. The limitation is the availability of aging data for electrical components.}, language = {en} } @article{BraunDurnerRabletal., author = {Braun, Peter and Durner, Bernhard and Rabl, Hans-Peter and Matysik, Frank-Michael}, title = {Investigations on the decomposition of AdBlue urea in the liquid phase at low temperatures by an electrochemically induced pH shift}, series = {Monatshefte f{\"u}r Chemie}, volume = {150}, journal = {Monatshefte f{\"u}r Chemie}, number = {9}, publisher = {Springer}, doi = {10.1007/s00706-019-02406-6}, pages = {1633 -- 1641}, abstract = {Ammonia-based selective catalytic reduction (SCR) systems are the most widely used technology for reduction of nitrogen oxide emissions from lean-burn engines such as diesel engines. However, at low exhaust temperatures, the SCR process is limited by difficulties in the decomposition of the ammonia precursor urea, which is carried on-board using an aqueous solution "AdBlue". In this study, the decomposition of AdBlue urea induced by electrical current and the resulting associated pH shifts were investigated in a divided cell configuration in the liquid phase. The decomposition was found to be favored in both electrochemical compartments, anodic and cathodic, at temperatures of 60-80 degrees C compared to a reference without electrochemical treatment. In addition to the determination of ammonia contents using an ammonia sensor, IC/HPLC analyses were carried out for each sample. Different side products such as biuret, nitrate, cyanuric acid, ammelide, and others were formed. In the anodic compartment, nitrate formation could be observed due to oxidation of ammonia at the electrode surface. [GRAPHICS] .}, language = {en} } @article{BraunRablMatysik, author = {Braun, Peter and Rabl, Hans-Peter and Matysik, Frank-Michael}, title = {Investigations on the Liquid-Phase Decomposition of AdBlue Urea for the Selective Catalytic Reduction Process}, series = {Chemie Ingenieur Technik}, volume = {91}, journal = {Chemie Ingenieur Technik}, number = {7}, publisher = {Wiley}, doi = {10.1002/cite.201800055}, pages = {961 -- 968}, abstract = {Difficulties in decomposing AdBlue to ammonia limit the applicability of selective catalytic reduction systems at low exhaust temperatures. Investigations on the decomposition of AdBlue in the liquid phase under elevated pressure at temperatures up to 165 degrees C were carried out. Besides effects of inorganic catalysts, the impact of pH on urea decomposition was examined. After dissolution in aqueous phase, the compounds ZnO, WO3, and MoO3 were found to be effective in liquid-phase AdBlue decomposition. However, the efficiency was dropping significantly over few hours. Decomposition of AdBlue urea was also found to be favored for alkaline and acidic conditions.}, language = {en} } @misc{Weiss, author = {Weiss, Nils}, title = {Vulnerabilities of OBD2 Dongles}, series = {RCAR Annual Conference, 2018, Munich, Germany}, journal = {RCAR Annual Conference, 2018, Munich, Germany}, language = {en} } @misc{Weiss, author = {Weiss, Nils}, title = {Vulnerabilities of Connected Cars and beyond}, series = {Applied Research Colloquium, 2019, Universit{\`a} Padua, Italy}, journal = {Applied Research Colloquium, 2019, Universit{\`a} Padua, Italy}, language = {en} } @article{PalombaNowakDawoudetal., author = {Palomba, Valeria and Nowak, Sebastian and Dawoud, Belal and Frazzica, Andrea}, title = {Dynamic modelling of Adsorption systems: a comprehensive calibrated dataset for heat pump and storage applications}, series = {Journal of energy storage}, volume = {33}, journal = {Journal of energy storage}, publisher = {Elsevier}, doi = {10.1016/j.est.2020.102148}, abstract = {The growing efforts for the development of clean and efficient energy systems require the use of a multi-disciplinary approach and the integration of multiple generation appliances. Among the fields that can be considered enabling technologies, adsorption systems for air conditioning and thermal energy storages, are constantly increasing their maturity. However, for a proper design and integration of such systems, there is the need for a simulation framework that is reliable and computationally convenient. In the present paper, the implementation of a dynamic model for adsorption systems is presented, which includes different components (adsorber, phase changer, sorption materials) and is structured as a library. Modelica language and the commercial software Dymola (R) are used for the analysis. Data for different heat exchangers and working pairs are calibrated using experimental results and the calibrated model is subsequently used for the design of an adsorber based on a plate heat exchanger for thermal energy storage applications. The results proved that the model is fast and can reproduce experimental results with good accuracy, thus being a useful tool for the design and optimization of the different components of sorption systems.}, language = {en} } @article{RillBauerKirchbeck, author = {Rill, Georg and Bauer, Florian and Kirchbeck, Mathias}, title = {VTT - a virtual test truck for modern simulation tasks}, series = {Vehicle system dynamics}, volume = {59}, journal = {Vehicle system dynamics}, number = {4}, publisher = {Taylor\&Francis}, doi = {10.1080/00423114.2019.1705356}, pages = {635 -- 656}, abstract = {The development of new technologies like advanced driver assistance systems or automated driving requires a flexible simulation environment of sufficient complexity. In general this flexibility is not provided by commercial software packages. This paper presents a three-dimensional and nonlinear hand-made model for heavy commercial vehicles including tractor and trailer as well as tractor and semitrailer combinations that can be used in different simulation environments, as well as in real-time applications. As typical for trucks, the torsional flexibility of the frame and a suspended driver's cabin are taken into account. The design kinematics makes it possible to handle different and quite complex axle suspensions very efficiently. Appropriate force elements are used to model various couplings between tractor and trailer or tractor and semitrailer, respectively. The virtual test truck environment (VTT) coded in ANSI C is extremely portable and can easily be embedded in commercial simulation packages like MATLAB/Simulink. It includes the TMeasy tyre model and offers flexible interfaces to third-party software tools.}, language = {en} } @article{Rill, author = {Rill, Georg}, title = {Sophisticated but quite simple contact calculation for handling tire models}, series = {Multibody system dynamics}, volume = {45}, journal = {Multibody system dynamics}, number = {2}, publisher = {Springer Nature}, organization = {SPRINGER}, doi = {10.1007/s11044-018-9629-4}, pages = {131 -- 153}, abstract = {Handling tire models like Pacejka (Tire and Vehicle Dynamics, 3rd edn., Elsevier, Amsterdam, 2012) or TMeasy (Rill in Proc. of the XV Int. Symp. on Dynamic Problems of Mechanics, Buzios, RJ, Brazil, 2013) consider the contact patch as one coherent plane. As a consequence, the irregularities of a rough road profile must be approximated by an appropriate local road plane that serves as an effective road plane in order to calculate the geometric contact point and the corresponding contact velocities. The Pacejka/SWIFT tire model employs a road enveloping model that generates the effective height and slope by elliptical cams. TMeasy just uses four representative road points for that purpose. In addition, TMeasy replaces the geometric contact point by the static contact point and shifts it finally to the dynamic contact point that represents the point where the contact forces are applied. In doing so, a rather sophisticated but still simple contact calculation is possible. Simulations obtained with a virtual tire test rig and fully nonlinear three-dimensional multibody system models of a motor-scooter and a passenger car demonstrate the potential of this contact approach.}, language = {en} }