@incollection{SternerEckertHenningetal., author = {Sterner, Michael and Eckert, Fabian and Henning, Hans-Martin and Trost, Tobias}, title = {Storage Demand in the Transport and Chemical Sector}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_5}, pages = {165 -- 188}, abstract = {In the transport sector, energy transition is still in its beginnings: shares of renewable fuels are at 5\% and are, with the exception of a small percentage in electrical rail transport, almost entirely restricted to biofuel. The transport sector, i.e., road, air, shipping, and rail traffic, consumes around 30\% of all final energy in Germany and its dependency of over 90\% on petroleum is still very high. As a result, its shares in greenhouse gas emissions are at 20\%. The necessary structural change in mobility, based on energy transition, is closely linked to the question of operating energy and of energy storage also. Aside from vehicles directly powered by wind or solar energy, mobility without storage is not possible: fuel tanks in cars, gas stations, and airplanes are omnipresent. The focus of the considerations on storage demand in the transport sector is on the question of how these storages can be used with renewable energies via bio and synthetic fuels, and on the question of how much storage is necessary for these new drive technologies, such as e-mobility. Before this, mobility needs today and in future need to be examined. In the chemical sector, the situation is very much alike: there is a great dependency on fossil resources, and decarbonization is inevitable to achieve ambitious climate goals. The structural change to convert and store renewable electricity as primary energy via power-to-X (PtX) represents a storage demand. First estimates will conclude this chapter.}, language = {en} } @incollection{SternerBreuerDreesetal., author = {Sterner, Michael and Breuer, Christopher and Drees, Tim and Eckert, Fabian and Maaz, Andreas and Pape, Carsten and Rotering, Niklas and Thema, Martin}, title = {Storage Demand in Power Supply}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_3}, pages = {51 -- 136}, abstract = {Energy storage systems (in the past as well as today) are one significant part in the energy supply. The following three chapters describe how storage demand will develop in the future for the electricity, heat, and traffic sectors, as well as for non-energetic consumption of fossil resources (the chemical industry). Chapter 3, the core of this section on storage demand, makes clear how and why the electricity sector is the nucleus of the energy supply of all sectors and why it creates essential bridges between electricity, heat, and transport sectors, as well as with the chemical industry. If planned electricity network expansion takes place and flexibilities in generation and consumption are fully exploited, the demand for electricity storage, according to present estimates, will only reach a significant scale at 60-80\% shares of renewable energy in the power supply. Network expansion has a great impact on the storage demand, as well as flexible power generation in power plants, combined heat and power (CHP), and flexible consumption via demand-side management (DSM). Four studies in the context of storage demand and the role of energy storage systems for flexibility are comprehensively addressed. The authors and the co-authors were themselves participants in these studies, which will be complemented by ongoing research. A meta-study summary of the main results is shown in Abschn. 3.7, and these results are compared with seven further studies.}, language = {en} } @incollection{Sterner, author = {Sterner, Michael}, title = {Energy Storage Through the Ages}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_1}, pages = {3 -- 22}, abstract = {Human beings have relied on stored energy since time immemorial. The planet's first mechanism for storing energy arose two billion years ago. Photosynthesis captures solar energy in chemical bonds; it is a process on which all life depends. With the discovery of fire around one-and-a-half million years ago, early man learned to access this stored energy by burning wood. Only since the Industrial Revolution have humans used fossil fuels, which are the results of biomass produced millions of years ago, then subjected to geological processes. Today, the long-term objective is to utilize sustainable biomass storage, replicate it by technical means, and to develop new storage technologies. This chapter is about the history of energy storage as it pertains to the carbon cycle. It begins with a natural energy storage system—photosynthesis—and examines its products biomass, peat, and fossil fuels before turning to storage technology in the era of renewable energies. It will also discuss how stored energy is used. This chapter focuses on natural biogenic and fossil energy storage. Other chapters are devoted to artificial storage technologies, including batteries, pumped-storage, and power-to-gas (PtG). Each begins with a short history of its respective technology.}, language = {en} } @incollection{SternerStadlerEckertetal., author = {Sterner, Michael and Stadler, Ingo and Eckert, Fabian and Gerhardt, Norman and von Olshausen, Christian and Thema, Martin and Trost, Tobias}, title = {Storage Integration for Coupling Different Energy Sectors}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_14}, pages = {757 -- 803}, abstract = {Electricity is becoming the primary source of energy, a trend that is particularly apparent through the coupling of the electricity sector with other energy sectors. In addition to the established links between the electricity and heating sectors using combined heat and power (CHP), which is supplemented by electric heat-pumps and power-to-heat (PtH), other new links are also emerging. These links are manifesting in the form of electro-mobility and electric fuels in the electricity and transport sectors; and in the electricity and gas sector they are appearing in the form of power-to-gas (PtG). The production of basic chemical materials such as methanol or polymers using electrical energy, water, and CO2 will also play a role in the future. However, the latter will not be dealt with explicitly here. Instead we will consider in detail other aspects of electricity as a primary energy source and its integration and application for energy storage.}, language = {en} } @incollection{SternerStadlerEckertetal., author = {Sterner, Michael and Stadler, Ingo and Eckert, Fabian and Thema, Martin}, title = {Storage Integration in Individual Energy Sectors}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_13}, pages = {675 -- 755}, abstract = {How is energy storage integrated and currently implemented in the electricity supply, heating supply, and mobility sectors? This chapter provides both theoretical and practical answers to that question. The chapter focuses on the integration of renewable energy. Cross-sectoral energy storage systems that link the electricity, heating, and mobility sectors are discussed in Kap. 14. This chapter focuses on storage integration in the electricity sector. After considering stand-alone networks, the chapter uses practical examples to analyze the various storage applications in the European network. The chapter concludes with a discussion of storage integration in the heating and transportation sectors.}, language = {en} } @incollection{SoergelRiedererHeldetal., author = {S{\"o}rgel, Matthias and Riederer, Michael and Held, Andreas and Plake, Daniel and Zhu, Zhilin and Foken, Thomas and Meixner, Franz X.}, title = {Trace Gas Exchange at the Forest Floor}, series = {Energy and Matter Fluxes of a Spruce Forest Ecosystem}, volume = {229}, booktitle = {Energy and Matter Fluxes of a Spruce Forest Ecosystem}, editor = {Foken, Thomas}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-49387-9}, doi = {10.1007/978-3-319-49389-3_8}, pages = {157 -- 179}, abstract = {Exchange conditions at the forest floor are complex due to the heterogeneity of sources and sinks and the inhomogeneous radiation but are important for linking soil respiration to measurements in the trunk space or above canopy. Far more attention has therefore been paid to above and within canopy flows, but even studies that addressed forest floor exchange do not present measurements below 1 m or 2 m. We used a multilayer model that explicitly resolves the laminar layer, the buffer layer, and the turbulent layer to calculate fluxes from the measured profiles in the lowest meter above ground and to calculate effective surface concentrations from given fluxes. The calculated fluxes were compared to measured eddy covariance fluxes of sensible heat and O3 and to chamber derived soil fluxes of CO2 and 222Rn. Sensible heat fluxes agreed surprisingly well given the heterogeneity of radiative heating and the generally low fluxes (max. 25 W m-2). The chamber fluxes turned out to be not comparable as the chamber fluxes were too low, probably due to one of the well-known problems of enclosures such as pressure differences, disturbed gradients and exclusion of naturally occurring turbulence events and surface cooling. The O3 fluxes agreed well for high O3 values reaching down to the forest floor during full coupling of the canopy by coherent structures. During most of the time, the model overestimated the fluxes as chemical reactions were dominating within the profile. One new approach was to calculate the effective surface concentration from a given flux and compare this to measured surface concentrations. This allowed the identification of situations with a coupled and decoupled forest floor layer, which has important consequences for respiration measurements in the trunk space or above canopy and should be considered in upcoming studies.}, language = {en} } @incollection{SternerBauer, author = {Sterner, Michael and Bauer, Franz}, title = {Definition and Classification of Energy Storage Systems}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_2}, pages = {23 -- 47}, abstract = {Energy supply always requires energy storage—either as an intrinsic property or as additional system. It is an intrinsic property of solid, liquid, and gaseous fuels, although less so of water-borne heat, but not of electricity. So to meet variable demands and supplies, heat and electricity networks usually require additional storage systems. When they are added to an energy network, should they be viewed as 'suppliers' or as 'consumers'? Who is responsible for covering the costs of storage systems? To categorize storage systems in the energy sector, they first need to be carefully defined. This chapter defines storage as well as storage systems, describes their use, and then classifies storage systems according to temporal, spatial, physical, energy-related, and economic criteria.}, language = {de} } @incollection{StadlerSterner, author = {Stadler, Ingo and Sterner, Michael}, title = {Urban Energy Storage and Sector Coupling}, series = {Urban Energy Transition}, booktitle = {Urban Energy Transition}, editor = {Droege, Peter}, edition = {2. ed.}, publisher = {Elsevier}, isbn = {978-0-08-102074-6}, doi = {10.1016/B978-0-08-102074-6.00026-7}, pages = {225 -- 244}, abstract = {Global warming, greenhouse gas emissions, and the general transition toward renewable energy resources are mentioned many times within this book, and will not be repeated again here. Countries that are transitioning to use of more renewable energy sources are mainly using wind and solar power—except for a few countries that, due to their prerequisites, will mainly use hydro power and/or bioenergy. The transmission process in terms of energy generation so far is mainly happening in rural areas—not in urban centers. Most technologies do not really play an important role in urban areas, and are mainly focused on the application of solar energy. Solar energy is widely applied more in rural areas, although investigations show that its application in urban areas already fits well into the existing grid infrastructure. Whereas rural areas are more prone to grid integration problems, the energy infrastructure in urban centers is already well prepared for renewables integration. In fostering tight bundles of potentially linked energy generation, distribution, networking, and use across power and thermal systems in stationary and mobile modes, urban centers become particularly critical in the energy transition processes as energy systems are becoming completely based on renewable sources without a nuclear or fossil-based backbone. This chapter discusses the almost unlimited energy storage possibilities. It will show their enormous capabilities, but also their significant differences in many physical and economical parameters. Next, the authors discuss the necessity of combining and coupling the different energy sectors for electricity, heat, cold, gas, and transport. Finally, the authors present the conclusion that only when coupling the energy sectors and using cheap and efficient energy storage options from one energy sector to solve challenges within another energy sector will the energy transition process be managed in an efficient way.}, language = {en} } @article{ThemaThema, author = {Thema, Johannes and Thema, Martin}, title = {Nachnutzungskonzept: Braunkohle-Tagebaue als Pumpspeicherkraftwerk?}, series = {Energiewirtschaftliche Tagesfragen - et : Zeitschrift f{\"u}r Energiewirtschaft, Recht, Technik und Umwelt}, volume = {69}, journal = {Energiewirtschaftliche Tagesfragen - et : Zeitschrift f{\"u}r Energiewirtschaft, Recht, Technik und Umwelt}, number = {4}, publisher = {ETV Energieverl.}, address = {Essen}, pages = {38 -- 39}, abstract = {Der Anteil fluktuierender erneuerbarer Energien im deutschen Strommix steigt. Um die Netzstabilit{\"a}t zu erhalten, Fluktuationen im Dargebot nach Wetterlage und saisonal auszugleichen sind absehbar ab ca. 2030 große Stromspeicherkapazit{\"a}ten erforderlich. Wasser-Pumpspeicherwerke sind derzeit die einzige langj{\"a}hrig erprobte Technologie, die k{\"u}nftig in Braunkohletagebauen, welche im Zuge der Energiewende aufgegeben werden, errichtet werden k{\"o}nnten. Eine {\"U}berschlagsrechnung am Beispiel eines Pumpspeicherwerks in verschiedenen Tagebauen zeigt, dass diese mit bis zu 400 GWh ein signifikantes technisches Speicherpotenzial haben.}, language = {de} } @unpublished{KaulBoellmannThemaetal., author = {Kaul, Anja and B{\"o}llmann, Andrea and Thema, Martin and Kalb, Larissa and St{\"o}ckl, Richard and Huber, Harald and Sterner, Michael and Bellack, Annett}, title = {Identification of Robust Thermophilic Methanogenic Archaea and Packing Material for High Liquid Hold-Up at Low Volumetric Gas Flow Rates for Use in Trickle-Bed Reactors for Biological Methanation}, series = {SSRN Electronic Journal}, journal = {SSRN Electronic Journal}, doi = {10.2139/ssrn.3940878}, abstract = {he hydrogen gas-to-liquid mass transfer is the limiting factor in biological methanation. In a trickle-bed reactor, mass transfer can be increased by high flow velocities in the liquid phase, by adding a packing material with high liquid hold-up, or by choosing methanogenic archaea with a high methane productivity. This study analyzed various packings and methanogenic strains from a hydrodynamic and microbial perspective. By analyzing twelve pure cultures of thermophilic methanogens for their ability to produce high quality methane and to form biofilms on different packings, strains of Methanothermobacter were found to perform better than thus of the genus Methanothermococcus. Best methane production and adherence was observed on DuraTop®, Bioflow 9, and filter foam. DuraTop® and Bioflow 9 had also a high dynamic liquid hold-up, but the maximum hold-up was determined for expanded clay. The ideal combination for use in the ORBIT-trickle-bed reactor was identified as Methanothermobacter thermoautotrophicus IM5 and DuraTop®.}, language = {en} } @incollection{SternerBauerHofrichter, author = {Sterner, Michael and Bauer, Franz and Hofrichter, Andreas}, title = {Systemanalyse von Power-to-X-Pfaden - Ergebnisse des Satellitenprojektes "SPIKE"}, series = {Optionen f{\"u}r ein nachhaltiges Energiesystem mit Power-to-X Technologien : Nachhaltigkeitseffekte - Potenziale Entwicklungsm{\"o}glichkeiten; 2. Roadmap des Kopernikus-Projektes "Power-to-X": Flexible Nutzung erneuerbarer Ressourcen (P2X)}, booktitle = {Optionen f{\"u}r ein nachhaltiges Energiesystem mit Power-to-X Technologien : Nachhaltigkeitseffekte - Potenziale Entwicklungsm{\"o}glichkeiten; 2. Roadmap des Kopernikus-Projektes "Power-to-X": Flexible Nutzung erneuerbarer Ressourcen (P2X)}, editor = {Ausfelder, Florian and Dura, Hanna Ewy}, publisher = {DECHEMA Gesellschaft f{\"u}r Chemische Technik und Biotechnologie e.V}, address = {Frankfurt am Main}, isbn = {978-3-89746-218-2}, pages = {145 -- 153}, language = {de} } @inproceedings{SchneiderNonnVoellingetal., author = {Schneider, Ingo and Nonn, Aida and V{\"o}lling, Alexander and Mondry, A. and Kalwa, Christoph}, title = {A damage mechanics based evaluation of dynamic fracture resistance in gas pipelines}, series = {Procedia Materials Science, Volume 3}, volume = {3}, booktitle = {Procedia Materials Science, Volume 3}, doi = {10.1016/j.mspro.2014.06.315}, pages = {1956 -- 1964}, abstract = {Investigation of running ductile fracture in gas transmission pipelines and the derivation of reliable crack arrest prediction methods belong to major topics in pipeline research. The yet available crack arrest criterion, known as the Battelle Two-Curve Method (BTCM), leads to reliable predictions up to grade X70 line pipe steels for which it has been validated. This includes specific limits in terms of mechanical properties, pressure and geometry. The application of this criterion to modern pipeline steels, i.e. especially grades X80 and beyond in combination with larger diameters and high pressure, has led to mispredictions of the BTCM. Hence, in order to ensure safe design of pipelines, new methods are required based on in depth knowledge and appropriate characterization of material resistance. This paper presents a procedure for the assessment of dynamic ductile fracture resistance based on combined experimental and numerical investigations. The procedure involves quasi-static and dynamic drop- weight tear testing (DWTT) on modified specimens with pre-fatigued crack for grades X65, X80 and X100 materials, and the application of cohesive zone (CZ) and Gurson-Tveergard-Needleman (GTN) models to describe ductile material damage. The damage model parameters are calibrated on basis of DWTT results and subsequently used to simulate dynamic crack propagation in a pipeline. The influence of material properties (strain hardening, toughness), pipe geometry, usage factor and decompression behaviour on ductile fracture propagation behaviour is studied and evaluated. The results will contribute to an enhanced understanding of major parameters controlling ductile fracture propagation and will help to establish a reliable procedure for safe design of new high-capacity pipelines with regard to crack arrest.}, language = {en} } @article{HaslbeckBrueckl, author = {Haslbeck, Matthias and Br{\"u}ckl, Oliver}, title = {Netzplanung Mittelspannungsnetze: Abbildung eines innovativen Blindleistungsmanagements, Teil 1 und 2}, series = {ew - Magazin f{\"u}r die Energiewirtschaft}, journal = {ew - Magazin f{\"u}r die Energiewirtschaft}, number = {7-8 und 9}, pages = {36 -- 39}, language = {de} } @incollection{SternerBauerCrotoginoetal., author = {Sterner, Michael and Bauer, Franz and Crotogino, Fritz and Eckert, Fabian and von Olshausen, Christian and Teichmann, Daniel and Thema, Martin}, title = {Chemical Energy Storage}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_8}, pages = {325 -- 482}, abstract = {Purely electrical energy storage technologies are very efficient, however they are also very expensive and have the smallest capacities. Electrochemical-energy storage reaches higher capacities at smaller costs, but at the expense of efficiency. This pattern continues in a similar way for chemical-energy storage. In terms of capacities, the limits of batteries (accumulators) are reached when low-loss long-term storage is of need. Chemical-energy storage and stocking fulfills these requirements completely. The storing itself may be subject to significant efficiency losses, but, from today's point of view and in combination with the existing gas and fuel infrastructure, it is the only national option with regards to the long-term storage of renewable energies. Chemical-energy storage is the backbone of today's conventional energy supply. Solid (wood and coal), liquid (mineral oil), and gaseous (natural gas) energy carriers are 'energy storages' themselves, and are stored using different technologies. In the course of energy transition, chemical-energy storage will be of significant importance, mainly as long-term storage for the power sector, but also in the form of combustibles and fuels for transport and heat. Not only are conventional storing technologies discussed within this chapter, but a detailed explanation is also given about the storage of renewable energies in the form of gaseous (power-to-gas, PtG) and liquid (power-to-liquid, PtL) energy carriers for electricity, heat, chemicals, and in the form of synthetic fuels.}, language = {en} } @incollection{SternerEckertGerhardtetal., author = {Sterner, Michael and Eckert, Fabian and Gerhardt, Norman and Henning, Hans-Martin and Palzer, Andreas}, title = {Heating Supply Storage Requirements}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_4}, pages = {137 -- 163}, abstract = {Unlike the electricity sector, heating and cooling storage requirements have attracted little public attention. This is because these storage requirements have generally already been met, and will not change significantly in the future. In the electricity sector by contrast, there will be a significant shift from primary energy storage to electricity and final energy storage. Both sectors have remarkably high storage requirements. Almost all households have thermal buffers. The same is true of renewable energy heating systems such as pellet heating, geothermal, or solar-thermal systems. Some households with liquid gas or oil heating even have two storage units: a fuel tank and a thermal buffer. Exceptions include heating systems with upstream storage such as district heating or gas storage. In the future, integration of the electricity and heating sectors by combined heat and power (CHP) generation, heat pumps, power-to-heat (PtH), and power-to-gas (PtG) will facilitate the use of renewable energy, and lead to a paradigm shift. Relying on results from various studies, this chapter examines the development of heating supply in Germany and the resulting thermal storage requirements. The chapter's later sections provide surplus and storage potential estimates. Cooling requirements are included as 'process cooling' under 'process heat', and as 'air-conditioning' over 'room heating'. It is primarily integrated into electricity demand.}, language = {en} } @incollection{StadlerBauerBudtetal., author = {Stadler, Ingo and Bauer, Franz and Budt, Marcus and Heindl, Eduard and Wolf, Daniel}, title = {Mechanical Energy Storage}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer Berlin Heidelberg}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_9}, pages = {483 -- 561}, abstract = {Chemical-energy storage systems use caverns, porous storage facilities, tanks, and storage rooms to store chemical energy sources. Caverns, caves, and reservoirs can also be used to store gaseous media such as air, liquid media such as water, and solid media such as rock. The principles of mechanical energy storage are based on classical Newtonian mechanics, or in other words on fundamental physics from the eighteenth and nineteenth centuries. As a result, these types of storage are typically divided into two categories; storage of kinetic and potential energy, or storage of 'pressure energy'. In this chapter, storage media is categorized by its aggregate state, and described by its function and application: first compressed air energy storage and then conventional electricity storage—pumped-storage plants. The chapter continues with a discussion of innovative methods of storing potential energy using water as a medium. These include artificially constructed pumped storage, pumped storage in the open sea, dam storage on rivers, pumped storage on heaps in repurposed mining areas, underfloor or underground pumped storage, and surface mine storage. The chapter concludes with a description of classical and modern flywheel energy storage systems. This age-old technology is then compared with a new concept: mechanical stored energy exploiting both pumped storage and change in the potential energy of rocks or large boulders.}, language = {en} } @article{EstermannNewboroughSterner, author = {Estermann, Thomas and Newborough, Marcus N. and Sterner, Michael}, title = {Power-to-gas systems for absorbing excess solar power in electricity distribution networks}, series = {International Journal of Hydrogen Energy}, volume = {41}, journal = {International Journal of Hydrogen Energy}, number = {32}, publisher = {Elsevier}, doi = {10.1016/j.ijhydene.2016.05.278}, pages = {13950 -- 13959}, abstract = {The feasibility of implementing power-to-gas systems, to absorb surplus solar power from electricity distribution networks and carbon dioxide from biomass anaerobic digestion (AD) plant, in order to produce synthetic methane was investigated for a region of Southern Germany that has a high solar power penetration. The analysis was based on time series electricity data for 2012 from which future load profiles were computed in accordance with the expected installed capacities of solar power across the period 2015-2025. The electrolyser capacity required to absorb 20\% of excess solar energy occurring within the region's low voltage network in 2025 was estimated to be 370 MWe. First order considerations of the region's gas grid, electricity network and existing AD sites suggest that such a deployment could be achieved by installing sub-MW (and some multi-MW) power-to-gas plant at several hundred AD sites.}, language = {en} } @incollection{StadlerEckert, author = {Stadler, Ingo and Eckert, Fabian}, title = {Load Management as an Energy Storage System}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_11}, pages = {611 -- 636}, abstract = {Chapters 6 to 9 focused on storage systems that store electric energy in a range of forms, and then release the energy again as electric energy. Chapter 10 discussed the use of thermal-energy storage (TES) systems for thermal management. This chapter examines management methods. These methods use processes that typically convert electric energy into another form of final energy that can also be stored. This form of energy is often thermal energy. But unlike with the systems discussed in previous chapters, here the energy stored is not converted back into electricity. Instead, the energy is used and stored in the same form. From the point of view of the energy supply system, these management methods perform exactly the same function as energy storage systems. This chapter discusses load-management in general, then potential uses of load-management, and finally, current trends.}, language = {en} } @article{ThemaSternerLencketal., author = {Thema, Martin and Sterner, Michael and Lenck, Thorsten and G{\"o}tz, Philipp}, title = {Necessity and Impact of Power-to-gas on Energy Transition in Germany}, series = {Energy Procedia}, volume = {99}, journal = {Energy Procedia}, publisher = {Elsevier}, doi = {10.1016/j.egypro.2016.10.129}, pages = {392 -- 400}, abstract = {The present paper gives an outlook on a bandwidth of required installed power-to-gas capacity in the German power sector fed by 100\% renewable generation until 2050. Two scenarios were simulated to quantify cost effects of power-to-gas on the electricity system: once with, once without additional short-term flexibility options to a system using fossil natural gas as sole flexibility option instead. As a result, at latest in 2035, power-to-gas capacity expansion has to take place to reach required installed capacities of up to 89-134 GW in 2050. Application of power-to-gas as long-term flexibility leads to cost savings of up to 11,7-19 bn Euro enabling a fully renewable system in 2050.}, language = {en} } @misc{OPUS4-3815, title = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, edition = {Translation of 2nd German edition Sterner, „Stadler Energiespeicher - Bedarf, Technologien, Integration"}, publisher = {Springer-Nature}, address = {Heidelberg, Berlin, New York}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0}, abstract = {There are several approaches to classifying energy storage systems (see Chaps. 1 and 2). Storage systems are used in a large number of different technologies at various stages of development, and in a wide range of application areas (see Chaps. 3 to 5). This chapter compares the capabilities of the different storage systems using the following criteria:This comparison of storage systems also provides a convenient overview of the various storage systems and their capabilities.}, language = {en} }