@article{KeinerBreyerSterner, author = {Keiner, Dominik and Breyer, Christian and Sterner, Michael}, title = {Coupling heat and electricity storage technologies for cost and self-consumption optimised residential PV prosumer systems in Germany}, series = {International Journal of Sustainable Energy Planning and Management}, volume = {21}, journal = {International Journal of Sustainable Energy Planning and Management}, publisher = {OJS/PKP}, doi = {10.5278/ijsepm.2019.21.4}, abstract = {Coupling energy sectors within the emerging residential PV prosumer systems is necessary for an optimised use of the houseowners' own produced electricity. But the pure availability of different energy technologies in the system is not enough. By optimising the electricity usage as well as the capacities of PV generators, storage technologies, heat pumps and battery electric vehicles, not only the best solution in a technical point of view can be achieved, the need of finding the most financially beneficial system composition for single-family houses and tenements is possible. The study provides a detailed model for average German single-family houses and tenements and results for the energy transition period until 2050 for the optimised energy systems regarding optimised PV and stationary battery capacities and different heat storage capacities. Most noticeable outcomes can be observed by using a vehicle-to-home car, where a car can mostly take over the tasks of a stationary battery and by introducing a solidarity model using this type of car in tenement systems.}, language = {en} } @article{EstermannNewboroughSterner, author = {Estermann, Thomas and Newborough, Marcus N. and Sterner, Michael}, title = {Power-to-gas systems for absorbing excess solar power in electricity distribution networks}, series = {International Journal of Hydrogen Energy}, volume = {41}, journal = {International Journal of Hydrogen Energy}, number = {32}, publisher = {Elsevier}, doi = {10.1016/j.ijhydene.2016.05.278}, pages = {13950 -- 13959}, abstract = {The feasibility of implementing power-to-gas systems, to absorb surplus solar power from electricity distribution networks and carbon dioxide from biomass anaerobic digestion (AD) plant, in order to produce synthetic methane was investigated for a region of Southern Germany that has a high solar power penetration. The analysis was based on time series electricity data for 2012 from which future load profiles were computed in accordance with the expected installed capacities of solar power across the period 2015-2025. The electrolyser capacity required to absorb 20\% of excess solar energy occurring within the region's low voltage network in 2025 was estimated to be 370 MWe. First order considerations of the region's gas grid, electricity network and existing AD sites suggest that such a deployment could be achieved by installing sub-MW (and some multi-MW) power-to-gas plant at several hundred AD sites.}, language = {en} } @inproceedings{RillButzRill, author = {Rill, Daniel and Butz, Christiane and Rill, Georg}, title = {Dynamic Interaction of Heavy Duty Vehicles and Expansion Joints}, series = {Multibody Dynamics 2019, Proceedings of the 9th ECCOMAS Thematic Conference on Multibody Dynamics}, volume = {53}, booktitle = {Multibody Dynamics 2019, Proceedings of the 9th ECCOMAS Thematic Conference on Multibody Dynamics}, editor = {Kecskem{\´e}thy, Andr{\´e}s and Geu Flores, Francisco}, publisher = {Springer International Publishing}, address = {Cham}, isbn = {978-3-030-23131-6}, doi = {10.1007/978-3-030-23132-3_56}, pages = {471 -- 478}, abstract = {The "Smart Bridge (Intelligente Br{\"u}cke)" project cluster, initiated by the German Federal Highway Research Institute (Bundesanstalt f{\"u}r Straßenwesen, BASt) and the Federal Ministry of Transport and Digital Infrastructure (BMVI), focuses on "smart" monitoring devices that allow an efficient and economic maintenance management of bridge infrastructures. Among the participating projects, the one presented herein focuses on the development of a smart expansion joint, to assess the traffic parameters on site. This is achieved by measuring velocity and weight of crossing vehicles. In reference measurements, performed with a three-axle truck and a typical tractor semi-trailer combination with five axles in total, it was shown that the interaction between the vehicle and the expansion joint is highly dynamic and depends on several factors. To get more insight into this dynamic problem, a virtual test rig was set up. Although nearly all vehicle parameters had to be estimated, the simulation results conform very well with the measurements and are robust to vehicle parameter variations. In addition, they indicate a significant influence of the expansion joint dynamic to the peak values of the measured wheel loads, in particular on higher driving velocities. By compensating the relevant dynamic effects in the measurements, a "smart" data processing algorithm makes it possible to determine the actual vehicle weights in random traffic with reliability and appropriate accuracy.}, language = {en} } @inproceedings{BuschmannBriem, author = {Buschmann, Knut and Briem, Ulrich}, title = {Ultra Deep Temperature Behaviour of Wire Rope and Rope Wires}, series = {Proceedings of the OIPEEC Conference, La Rochelle, France, 12th - 15th March 2019}, booktitle = {Proceedings of the OIPEEC Conference, La Rochelle, France, 12th - 15th March 2019}, editor = {Dohm, Martin}, abstract = {Mobile cranes are regularly operated in regions which experience ultra deep operating temperatures of down to -60?C (-76?F). In safety regulated work environments crane operations will be suspended simply because the lowest wire rope working temperature stated in the applicable standards is -40?C/F. Examples of ultra deep temperature wire rope application are shown in Figure 1.1 and 1.3. It should be noted that this paper is written in conjunction with a paper written by the co-author Ulrich Briem titled "Fatigue Behaviour of Rope Wires", presented and published in unison with this one. In order to analyze the behaviour under ultra deep temperature conditions, tests on wire rope as well as on rope wires were carried out. In the following, static tensile and bending test results with rope and rope wires will be reported, which were carried out in conditions of down to -95?C (-139?F) as well as at room temperature. The conclusion is that the results of these tests can be adopted to crane wire rope as well.}, language = {en} } @inproceedings{HofmeisterKrebsSchickhuberetal., author = {Hofmeister, Justus and Krebs, Stefan and Schickhuber, Gerald and Scharfenberg, Georg}, title = {Design and development of a Pico Hydro turbine system for the use in developing countries}, series = {2015 5th International Youth Conference on Energy (IYCE), 27-30 May 2015, Pisa, Italy}, booktitle = {2015 5th International Youth Conference on Energy (IYCE), 27-30 May 2015, Pisa, Italy}, publisher = {IEEE}, doi = {10.1109/IYCE.2015.7180767}, pages = {1 -- 7}, abstract = {In Sub-Saharan Africa less than 10\% of the rural population has access to electricity [1]. Stand-alone power systems (SPS) can be a solution to the problem of the lack of electricity, which highlights challenges such as modules installation costs as well as the sufficient knowledge required for installing, maintaining and operating such systems. With this fact in mind, a 250 W Low Head turbine system was developed and optimized to have the advantage of the simplicity of installation and a construction from readily available materials. This design scores the electrical efficiency of 60\%, reduces manufacturing unit coast to 130 € and takes into account the necessity of providing a clear and simple manual describing the manufacturing and installation. A better version of the load controller, using a microcomputer is under current development. Mounting of the system have been simplified to reduce the amount of construction material required to provide uninterrupted 230 V at 50 Hz AC or optional 12 V DC power supply. Current efforts aim on transferring the required mechanical and electrical knowledge for building, programming, installing and maintaining such system to schools in targeted countries. This project doesn't only provide people in rural developing countries a gleam of hope to catch up with the developed countries, but also helps students to use their theoretical knowledge to realize practical applications.}, language = {en} } @article{FederrathMottokPloessletal., author = {Federrath, H. and Mottok, J{\"u}rgen and Pl{\"o}ßl, K. and V{\"o}lkl, Thomas}, title = {Automotive safety and security}, series = {Jahresr{\"u}ckblick 2007 des Bayerischen IT-Sicherheitsclusters}, journal = {Jahresr{\"u}ckblick 2007 des Bayerischen IT-Sicherheitsclusters}, pages = {25}, language = {de} } @article{SykoraMarkovaDiamantidis, author = {S{\´y}kora, Miroslav and Markova, Jana and Diamantidis, Dimitris}, title = {Bayesian network application for the risk assessment of existing energy production units}, series = {Reliability Engineering \& System Safety}, volume = {169}, journal = {Reliability Engineering \& System Safety}, number = {January}, publisher = {Elsevier}, doi = {10.1016/j.ress.2017.09.006}, pages = {312 -- 320}, abstract = {The assessment of existing infrastructures in the energy sector is of great economic significance worldwide. Fossil power stations are reaching their design service life and rational decisions concerning extensions of service life, maintenance and replacements of devices should be based on updated information of the actual conditions of the energy devices and their components, and on cost-benefit analysis using risk analysis and probabilistic optimisation procedures. The contribution provides an integrated framework for probabilistic reliability and risk assessment of existing energy production units considering availability and human safety criteria. An extensive case study focused on risks of an energy production unit in a fossil power station is provided to support practical applications. A Bayesian network is thereby implemented to assess the risks of the selected production unit. Special emphasis is given to the input data consisting of failure rates obtained from recorded data and expert judgements. The influence of uncertainties in the considered performance indicators on the availability of the unit is analysed. It is shown that a reasonably simplified framework can provide a valuable assessment of the influence of individual devices and their components on availability and societal risk, identifying thus the major risk contributors. (C) 2017 Elsevier Ltd. All rights reserved.}, language = {en} } @article{WeberHaug, author = {Weber, Karsten and Haug, Sonja}, title = {Ist automatisiertes Fahren nachhaltig?}, series = {TATuP - Zeitschrift f{\"u}r Technikfolgenabsch{\"a}tzung in Theorie und Praxis}, volume = {27}, journal = {TATuP - Zeitschrift f{\"u}r Technikfolgenabsch{\"a}tzung in Theorie und Praxis}, number = {2}, publisher = {Karlsruhe Institute of Technology (KIT)}, doi = {10.14512/tatup.27.2.16}, pages = {16 -- 22}, abstract = {Automatisiertes Fahren st{\"o}ßt derzeit noch auf große Skepsis. Eine disruptive Strategie bei der Einf{\"u}hrung (voll-)automatisierten Fahrens k{\"o}nnte daher auf fehlende Akzeptanz treffen. Um dem zu entgehen, laufen evolution{\"a}re Strategien darauf hinaus, durch die Entwicklung adaptiver Fahrassistenzsysteme Vertrautheit, Vertrauen und damit Akzeptanz bei den prospektiven NutzerInnen zu schaffen. Erste Ergebnisse einer Pilotstudie lassen jedoch Zweifel an der Nachhaltigkeit dieser Strategie aufkommen.}, language = {de} } @inproceedings{KeimNonnLenzetal., author = {Keim, Vincent and Nonn, Aida and Lenz, D. and Brinnel, Viktoria and M{\"u}nstermann, Sebastian}, title = {Simulation of the ductile fracture behaviour of high toughness pipeline steels using combined damage models}, series = {Proceedings of the conference on Technology for future and ageing piplines, Ghent, Belgium}, booktitle = {Proceedings of the conference on Technology for future and ageing piplines, Ghent, Belgium}, language = {en} } @inproceedings{NonnKalwa, author = {Nonn, Aida and Kalwa, Christoph}, title = {Simulation of ductile crack propagation in high-strength pipeline steel using damage models}, series = {9th International Pipeline Conference 2012 (IPC 2012), Calgary, Canada}, booktitle = {9th International Pipeline Conference 2012 (IPC 2012), Calgary, Canada}, doi = {10.1115/IPC2012-90653}, pages = {7}, abstract = {The performance of engineering design of high-strength steel pipelines has revealed the necessity to revise current design procedures. Therefore, an improved and detailed comprehension of fracture mechanisms and development of failure prediction tools are required in order to derive new design criteria. In last decades the most successful failure prediction tools for steel structures subjected to various type of loading can be encountered in the field of damage mechanics. This paper aims to describe ductile fracture behavior of high-strength steel pipelines by applying three different damage models, Gurson-Tvergaard-Needelman (GTN), Fracture Locus Curve (FLC) and Cohesive Zone (CZ). These models are evaluated regarding their capability to estimate ductile crack propagation in laboratory specimens and linepipe components without adjusting the calibrated parameters. It can be shown that appropriate parameter sets can be identified to reproduce load-deformation and fracture resistance curves accurately. The strain rate effect on the fracture behavior is examined by dynamic tests on the BDWT specimens. Finally, the shortcomings of the applied models are pointed out with the reference to possible extensions and modifications.}, language = {en} } @article{LeeSchubertOoietal., author = {Lee, Wai-Kong and Schubert, Martin J. W. and Ooi, Boon Yaik and Ho, Stanley Jian-Qin}, title = {Multi-source energy harvesting and storage for floating wireless sensor network nodes with Long Range Communication Capability}, series = {IEEE Transactions on Industry Applications}, volume = {54}, journal = {IEEE Transactions on Industry Applications}, number = {3}, publisher = {IEEE}, doi = {10.1109/TIA.2018.2799}, pages = {2606 -- 2615}, abstract = {Wireless sensor networks are widely used for environmental monitoring in remote areas. They are mainly composed of wireless sensor nodes, usually powered by batteries with limited capacity, but are expected to communicate in long range and operate for extended time periods. To overcome these limitations, many energy harvesting techniques are proposed to power wireless nodes for prolonged operation, whereas multihop techniques are utilized to extend the communication range. In this paper, a novel floating device with multisource energy harvesting technology that can be used as a wireless sensor node is proposed. The long range communication between wireless sensor nodes and a gateway is established through LoRa technology. In addition to conventional solar panels, an energy harvesting technique based on thermoelectric generators exploiting thermal differences created between water surface and materials exposed to sunlight is proposed. Energy generated from photovoltaic and thermoelectric generators is combined to power the wireless sensor node. This floating device consumes 6.6216 Wh per day when used as a wireless sensor node for the collection and transmission of environmental data. The sensor node can operate on a water surface for at least 9.6 days when it is not exposed to sunlight. During a sunny day, the floating device can harvest 8.375 Wh from solar panels and 0.425 Wh from thermoelectric generation. In other words, the floating device harvests sufficient energy to be self-sustaining during sunny days.}, language = {en} } @article{HaugVetterWeber, author = {Haug, Sonja and Vetter, Miriam and Weber, Karsten}, title = {Geb{\"a}udesanierung zwischen Energieeffizienz und Sozialvertr{\"a}glichkeit}, series = {TATuP - Zeitschrift f{\"u}r Technikfolgenabsch{\"a}tzung in Theorie und Praxis}, volume = {29}, journal = {TATuP - Zeitschrift f{\"u}r Technikfolgenabsch{\"a}tzung in Theorie und Praxis}, number = {3}, publisher = {oekom-Verlag}, issn = {2567-8833}, doi = {10.14512/tatup.29.3.56}, pages = {56 -- 63}, abstract = {Die Akzeptanz unter Bewohnern und Bewohnerinnen gewinnt bei hoch komplexen, technisch anspruchsvollen energetischen Sanierungen als „Innovationsmotor" zunehmend an Relevanz. Der Beitrag basiert auf zwei Fallstudien zur partizipativen Nutzereinbindung bei energetischen Sanierungen im genossenschaftlichen Wohnbau historischer Stadtquartiere in Regensburg. Neben einer sozialvertr{\"a}glichen Sanierung wurde jeweils ein hohes Maß an Energieeffizienz bei den technischen L{\"o}sungen ange-strebt. Haushaltsbefragungen und qualitative Interviews zeigen die hohe Akzeptanz von Sanierungsmaßnahmen, sofern die Senkung der Energiekosten die erh{\"o}hte Miete kompensiert. Abschließend werden Akzeptanzfaktoren wie Partizipation, Vertrauen, Sozialvertr{\"a}glichkeit und Autarkie er{\"o}rtert.}, subject = {Altbaumodernisierung}, language = {de} } @inproceedings{WeberHaug, author = {Weber, Karsten and Haug, Sonja}, title = {Automatisiertes Fahren: Evolution{\"a}re Weiterentwicklung statt Disruption}, series = {Vierte Jahreskonferenz des Netzwerks INDIGO zum Thema "Mobilit{\"a}t", 23.11.2018, , TH Deggendorf}, booktitle = {Vierte Jahreskonferenz des Netzwerks INDIGO zum Thema "Mobilit{\"a}t", 23.11.2018, , TH Deggendorf}, language = {de} } @inproceedings{DeNiklasRooneyetal., author = {De, Sangita and Niklas, Michael and Rooney, Brian and Mottok, J{\"u}rgen and Brada, Premek}, title = {Towards Translation of Semantics of Automotive Interface Description Models from Franca to AUTOSAR Frameworks}, series = {2019 International Conference on Applied Electronics (AE), 10-11 Sept. 2019, Pilsen, Czech Republic}, booktitle = {2019 International Conference on Applied Electronics (AE), 10-11 Sept. 2019, Pilsen, Czech Republic}, publisher = {University of West Bohemia}, doi = {10.23919/AE.2019.8867018}, pages = {1 -- 6}, abstract = {The automotive industry is eventually evolving into a complex network of services. The heterogeneous and distributed nature of automotive software systems demands flexible software components which can operate in different environments. Because of heterogeneous automotive development environments, the domain experts, must cope with too many diversities, adaption layers, and incompatibilities to design applications for the current generation of autonomous driving vehicles. In this context, interface adaptation is a promising approach to achieve flexibility without directly changing the respective components. AUTOSAR, which is the de-facto standard for describing automotive system architecture and is a hugely comprehensive standard allowing designers full control from abstract system description to bare metal level deployment. However, the vehicle subsystems have still evolved to include multifarious high-level domains not covered by AUTOSAR e.g. Infotainment, Telematics etc. Therefore, it seems beneficial to bridge the semantic gaps between AUTOSAR applications and other standards of automotive application domains. The goal of this paper is to investigate interface semantic mapping and achieve transparent integration of domain-specific applications using the translation of semantics among the AUTOSAR platform software component models and other software components models of open source development platforms e.g. GENIVI. A key goal of such a modelling approach is the reuse of existing interface description languages and respective code generators. This will enhance future interoperability and decrease in incompatibility among these platforms.}, language = {en} } @article{SelmairMaurerLaietal., author = {Selmair, Maximilian and Maurer, Tobias and Lai, Chun-Han and Grant, David}, title = {Enhancing the efficiency of charging \& parking processes for Autonomous Mobile Robot fleets}, series = {Journal of Power Sources}, volume = {521}, journal = {Journal of Power Sources}, number = {3}, publisher = {Elsevier}, doi = {10.1016/j.jpowsour.2021.230894}, abstract = {The allocation of tasks to Autonomous Mobile Robots in a production setting in combination with the most efficient parking and charging processes are the focus of this paper. This study presents a simulative evaluation of the theoretical allocation methods developed in Selmair and Maurer (2020) combined with either hard or dynamic availability rules to ascertain the most efficient parameters of an Autonomous Mobile Robot System. In order to quantify this efficiency, the following Key Performance Indicator (KPI) were considered: number of delayed orders, driven fleet metres and the percentage of available Autonomous Mobile Robot as determined by their state of charge. Additionally, as an alternative energy source, a fast-charging battery developed by Battery Streak Inc. was included in this study. The results show that, in comparison to a conventional and commonly used trivial strategy, our developed strategies provide superior results in terms of the relevant KPI.}, language = {en} } @inproceedings{JupkeReindlMeieretal., author = {Jupke, Michael and Reindl, Andrea and Meier, Hans and Niemetz, Michael}, title = {Bidirectional DC-DC Converter with Digital Droop Parameterization}, series = {26th 2021 International Conference on Applied Electronics (AE): 7-8 Sept. 2021 Pilsen, Czech Republic}, booktitle = {26th 2021 International Conference on Applied Electronics (AE): 7-8 Sept. 2021 Pilsen, Czech Republic}, editor = {Pinker, Jiř{\´i}}, publisher = {Institute of Electrical and Electronics Engineers}, isbn = {978-80-261-0972-3}, doi = {10.23919/AE51540.2021.9542920}, pages = {1 -- 6}, abstract = {The key for decentralized battery systems is a robust and communication-less control strategy for autonomous power sharing of parallel-connected DC-DC converters. Battery systems improve the reliability and quality of power supply in renewable energy systems and enable power supply for off-grid, mobile applications, including islanded grids, home storage, and electric vehicles. In many cases, components with different electrical properties require different voltage levels. An adaptation is consequently essential and is normally implemented in DC grids for the batteries via bidirectional DC-DC converters. The power flow in both directions can thus be ensured. To achieve a power distribution in parallel connected DC-DC converters, a droop control in the form of a virtual internal resistor can be used. This paper presents a novel approach of a DC-DC converter with a digitally parameterizable droop resistor, whose voltage regulation is based on an analog operational amplifier circuit to ensure low delays and robustness. The droop resistor is adjusted with a microcontroller, which offers the possibility to apply a higher-level control for load sharing via an interface. Mathematical correlations are used to clearly define the parameters of the control. Furthermore, the circuit was completely simulated and tested in the hardware setup. The shown results verify the functionality and indicate only minor deviations. Therefore, this circuit is important for future use in distributed battery systems.}, language = {en} } @inproceedings{BoccaraDiamantidisSykora, author = {Boccara, R. and Diamantidis, Dimitris and S{\´y}kora, Miroslav}, title = {Optimal design of ground-mounted solar systems}, series = {Safety and reliability : methodology and applications : proceedings of the European Safety and Reliability Conference, ESREL 2014, Wrocław, Poland, 14-18 September 2014}, booktitle = {Safety and reliability : methodology and applications : proceedings of the European Safety and Reliability Conference, ESREL 2014, Wrocław, Poland, 14-18 September 2014}, publisher = {CRC Press}, address = {Boca Raton}, isbn = {978-1-138-02681-0}, pages = {2175 -- 2181}, abstract = {Solar energy represents a clean, natural and sustainable source of energy. Solar photovoltaic panels can be installed on roofs of structures or in the ground. This contribution focusses on ground-mounted systems, which are presently widely implemented. At present limited guidelines on the design of solar ground-mounted structures are available. Usually standards for the design of normal buildings are applied. However, the design of ground-mounted structures significantly differs from common structural design by: (1) a lower design lifetime (20-25 years) is accepted; (2) failure is not associated with the loss of human life; (3) resistance uncertainties need due attention; (4) uplift wind forces dominating structural reliability are associated with a large scatter. That is why the reliability analysis and optimal design of ground-mounted solar systems is investigated herein. The failure costs and especially their ratio to the initial costs are analyzed considering the data provided from the industry. Probabilistic reliability analyses are carried out and optimum design levels are computed for representative cost ratios. The optimal target reliability depends on the ratio between failure and initial costs; reliability index of 3.5 corresponds to a reasonable cost ratio of 10.}, language = {en} } @inproceedings{KasparKleinerRabl, author = {Kaspar, Marcel and Kleiner, Florian and Rabl, Hans-Peter}, title = {Online-Analyse und Optimierung der Schmier{\"o}lverd{\"u}nnung bei direkteinspritzenden Ottomotoren}, series = {7. VDI-Fachtagung mit Fachausstellung Zylinderlaufbahn, Kolben, Pleuel : Baden-Baden, 03. und 04. Juni 2014}, booktitle = {7. VDI-Fachtagung mit Fachausstellung Zylinderlaufbahn, Kolben, Pleuel : Baden-Baden, 03. und 04. Juni 2014}, publisher = {VDI-Verlag}, address = {D{\"u}sseldorf}, isbn = {978-3-18-092230-0}, pages = {65 -- 77}, abstract = {Bei Ottomotoren mit Direkteinspritzung besteht beim Kaltstart, den Warmlaufphasen und auch durch den Einfluss anderer Parameter wie z. B. des Einspritzzeitpunkts oder des Einspritzdrucks die Problematik, dass Kraftstoff an die Zylinderlaufbahn aufgetragen wird und sich mit dem Motor{\"o}l vermischen kann. Eine Verst{\"a}rkung dieses Kraftstoffauftrags ist unter anderem der Verschiebung der Motorbetriebspunkte zu h{\"o}heren Mitteldr{\"u}cken und damit einem Wirkungsgrad optimaleren Betrieb geschuldet. Eine Ver{\"a}nderung der physikalischen und chemischen Eigenschaften des Motor{\"o}ls durch die Verd{\"u}nnung mit Kraftstoff ist die Folge. Durch die Verringerung der Viskosit{\"a}t des Motor{\"o}ls kann es zu einer verminderten Schmierwirkung des {\"O}ls kommen, die im schlimmsten Fall zur Sch{\"a}digung des Motors f{\"u}hrt. Existierende Offline-Analysemethoden die zeitintensive Laboranalysen nach sich ziehen, als auch Online-Messverfahren die nicht den technischen Anforderungen hinsichtlich Genauigkeit und einer kurzen Messdauer entsprechen, stellen aktuell die einzigen Messmethoden zur Bestimmung der Schmier{\"o}lverd{\"u}nnung dar. Durch neue Entwicklungstrends bei Ottomotoren ist es jedoch unbedingt notwendig, die Mechanismen des Kraftstoffein- und -austrags in das und aus dem Motor{\"o}l genauer zu untersuchen. Mit der an der OTH Regensburg neu entwickelten Messtechnik wurde eine Vorgehensweise erarbeitet, mit der die zeitlichen Verl{\"a}ufe des Kraftstoffein- und -austragsverhaltens bei Ottomotoren quantitativ in kurzer Zeit bestimmt und optimiert werden k{\"o}nnen. Especially at cold start and the warm-up operation GDI engines have an issue with oil dilution. Parameters such as injection timing and injection pressure impact the entry of fuel in the engine oil as well. With the adjustment of engine operating points to higher mean effective pressures resulting in downsizing concepts also an additional increase of fuel entry occurs. Fuel gets into the oil pan and is mixed with the engine oil so that the physical and chemical properties of the engine oil are changed. With the reduction of engine oil viscosity due to fuel entry a reduced lubricating effect can be caused. In the worst case damage to the engine occurs, To determine oil dilution online and offline measurement methods exist. A rather long analysis time in the laboratory is a disadvantage of the offline methods. Online methods are not correlating with technical requirements in terms of accuracy and a short measurement time. New trends in the development of gasoline engines require investigations of fuel in oil sorption and desorption processes. A new measurement technique which is developed at the OTH Regensburg enables to determine quantitative fuel in oil sorption and desorption processes. With this technique a procedure was generated to measure the oil dilution at gasoline engines and optimize them in a short time.}, language = {de} } @article{KeimMarxNonnetal., author = {Keim, Vincent and Marx, P. and Nonn, Aida and M{\"u}nstermann, Sebastian}, title = {Fluid-structure-interaction modeling of dynamic fracture propagation in pipelines transporting natural gases and CO2-mixtures}, series = {International Journal of Pressure Vessels and Piping}, volume = {175}, journal = {International Journal of Pressure Vessels and Piping}, number = {August}, publisher = {Elsevier}, doi = {10.1016/j.ijpvp.2019.103934}, abstract = {As part of current design standards, the Battelle Two-Curve Model (BTCM) is still widely used to predict and secure ductile crack arrest in gas transmission pipelines. For modern linepipe steels and rich natural gases or CO2 mixtures, the BTCM might lead to incorrect predictions. On the one hand, it suffers from the insufficient description of the individual physical processes in the pipe material and fluid itself. Furthermore, the model does not account for fluid-structure-interaction (FSI) effects during simultaneous running-ductile fracture (RDF) and mixture decompression. Numerical FSI models allow for a more sophisticated, coupled analysis of the driving forces for the failure of pipelines. This paper deals with the development of an FSI model for the coupled prediction of 3D pressure profiles acting on the inner pipe wall during crack propagation. The coupled Euler-Lagrange (CEL) method is used to link the fluid and structure models. In a Lagrange formulation, the modified Bai-Wierzbicki (MBW) model describes the plastic deformation and ductile fracture as a function of the underlying stress/strain conditions. The fluid behavior is calculated in a 3D model space by Euler equations and the GERG-2008 reference equation of state (EOS). The coupled CEL model is used to predict the RDF in small-diameter pipe sections for different fluid mixtures. The calculated 3D pressure distributions ahead and behind the running crack tip (CT) significantly differ in axial and circumferential directions depending on the mixture composition. The predicted FSI between the pipe wall and fluid decompression in 3D CEL/FSI model provides reliable knowledge about the pressure loading of the pipeline during RDF.}, subject = {Fluid-Struktur-Wechselwirkung}, language = {en} } @article{KeimNonnMuenstermann, author = {Keim, Vincent and Nonn, Aida and M{\"u}nstermann, Sebastian}, title = {Application of the modified Bai-Wierzbicki model for the prediction of ductile fracture in pipelines}, series = {International Journal of Pressure Vessels and Piping}, volume = {171}, journal = {International Journal of Pressure Vessels and Piping}, number = {March}, publisher = {Elsevier}, doi = {10.1016/j.ijpvp.2019.02.010}, pages = {104 -- 116}, abstract = {The complex mechanical and corrosive loads of modern pipeline systems transporting oil, natural gas and CO2 impose steadily increasing requirements on material properties. The majority of current design standards still limit the application of modern high toughness linepipe steels due to the simple specification of material requirements in terms of energy levels from Charpy impact or Battelle Drop-Weight-Tear (BDWT) tests. In consequence, research activities have been conducted recently aiming at developing modified or novel experimental methods for the characterization of the ductile fracture behavior. To quantify the effects of various parameters on fracture behavior and derive suitable correlations, it is necessary to accompany these activities by numerical simulations with appropriate ductile damage models. In this paper, the MBW model is applied to study the structural behavior of pipelines in ductile fracture regime. Due to its precise incorporation of the underlying load conditions, the damage model is successfully used to simulate the slant fracture behavior in Battelle Drop weight tear test specimens and pipe sections. In comparison to ductile damage models applied in former studies, namely the Gurson-Tvergaard-Needleman and Cohesive Zone model, the presented numerical methodology allows for a more detailed investigation of loading, material and geometry effects on fracture and crack arrest behavior of pipelines.}, language = {en} } @inproceedings{ReindlMeierNiemetz, author = {Reindl, Andrea and Meier, Hans and Niemetz, Michael}, title = {Scalable, Decentralized Battery Management System Based on Self-organizing Nodes}, series = {Architecture of computing systems - ARCS 2020: 33rd international conference, Aachen, Germany, May 25-28, 2020, proceedings}, volume = {12155}, booktitle = {Architecture of computing systems - ARCS 2020: 33rd international conference, Aachen, Germany, May 25-28, 2020, proceedings}, editor = {Brinkmann, Andr{\´e} and Karl, Wolfgang and Lankes, Stefan and Tomforde, Sven and Pionteck, Thilo and Trinitis, Carsten}, publisher = {Springer International Publishing}, address = {Cham}, isbn = {978-3-030-52793-8}, doi = {10.1007/978-3-030-52794-5_13}, pages = {171 -- 184}, abstract = {Due to the transition to renewable energy sources and the increasing share of electric vehicles and smart grids, batteries are gaining in importance. Battery management systems (BMSs) are required for optimal, reliable operation. In this paper, existing BMS topologies are presented and evaluated in terms of reliability, scalability and flexibility. The decentralisation of BMSs and associated advantages are shown. A scalable, reconfigurable BMS based on a distributed architecture of self-organized, locally controlled nodes is proposed. For distributed system control, producers, batteries and consumers each are equipped with a local microcontroller based control unit, which monitors and controls the local parameters with its own computing and communication resources. Features, advantages and challenges to overcome of the proposed approach are described.}, language = {en} } @inproceedings{VoellingNonnSchneider, author = {V{\"o}lling, Alexander and Nonn, Aida and Schneider, Ingo}, title = {Anwendung des Koh{\"a}sivzonenmodells zur Abbildung von duktilem dynamischen Rissfortschritt in Gasfernleitungen}, series = {45. Tagung des AK Bruch, Berlin, Germany}, booktitle = {45. Tagung des AK Bruch, Berlin, Germany}, pages = {253 -- 262}, subject = {Ferngasleitung}, language = {de} } @article{MikhaeilGadererDawoud, author = {Mikhaeil, Makram and Gaderer, Matthias and Dawoud, Belal}, title = {Experimental Investigation of the Adsorption and Desorption Kinetics on an Open-Structured Asymmetric Plate Heat Exchanger; Matching Between Small-Scale and Full-Scale Results}, series = {Frontiers in Energy Research}, volume = {10}, journal = {Frontiers in Energy Research}, publisher = {Frontiers}, doi = {10.3389/fenrg.2022.818486}, pages = {1 -- 15}, abstract = {This paper introduces the results of an experimental study on the adsorption and desorption kinetics of a commercially available, open-structured asymmetric plate heat exchanger adapted to act as an adsorber/desorber for the application in adsorption heat transformation processes. In addition, a volumetric large temperature jump (V-LTJ) kinetic setup was applied to measure the adsorption and desorption kinetics of a small-scale adsorbent sample prepared dedicatedly to be representative for the adsorbent domain inside the investigated adsorber plate heat exchanger (APHE). All kinetic results of the small-scale adsorbent sample and the APHE were fitted into exponential forms with a single characteristic time constant (τ) with a coefficient of determination (R2) better than 0.9531. A very good matching between the small-scale and full-scale adsorption kinetic measurements was obtained, with an average relative deviation of 12.3\% in the obtained τ-values. In addition, the kinetic data of the small-scale adsorbent sample were utilized for estimating the expected specific instantaneous and moving average powers of the evaporator/condenser heat exchanger. The average relative deviation (ARD) between the moving average specific evaporator powers obtained from the small-scale and the full-scale measurements amounts between 5.4 and 15.1\%.}, language = {en} } @inproceedings{ArrietaCastroWeberRill, author = {Arrieta Castro, Abel and Weber, Hans Ingo and Rill, Georg}, title = {Design an integrate vehicle control based-on hierarchical architecture for improve the performance of ground vehicles}, series = {COBEM2015 : 23rd ABCM International Congress of Mechanical Engineering, December 6-11, 2015, Rio de Janeiro, RJ, Brazi}, booktitle = {COBEM2015 : 23rd ABCM International Congress of Mechanical Engineering, December 6-11, 2015, Rio de Janeiro, RJ, Brazi}, organization = {Associa{\c{c}}{\~a}o Brasileira de Engenharia e Ci{\^e}ncias Mec{\^a}nicas}, doi = {10.20906/cps/cob-2015-1970}, language = {en} } @inproceedings{AndersBriemNovaketal., author = {Anders, M. and Briem, Ulrich and Novak, G. and Steinbach, G.}, title = {Neue VDI-Richtlinie f{\"u}r die Seiltriebauslegung}, series = {28. Internationale Kranfachtagung 2020 "Kran 4.0: Potenziale der Digitalisierung", 4. und 5. M{\"a}rz 2020, Magdeburg}, booktitle = {28. Internationale Kranfachtagung 2020 "Kran 4.0: Potenziale der Digitalisierung", 4. und 5. M{\"a}rz 2020, Magdeburg}, editor = {Katterfeld, Andr{\´e} and Krause, Friedrich and Pfeiffer, Dagmar and Richter, Klaus}, publisher = {LOGiSCH GmbH}, address = {Magdeburg}, isbn = {978-3-947068-08-1}, pages = {59 -- 72}, language = {de} } @article{MonkmanSindersbergerPremetal., author = {Monkman, Gareth J. and Sindersberger, Dirk and Prem, Nina and Diermeier, Andreas and Szecsey, Tamara}, title = {Dielectric behaviour of magnetic hybrid materials}, series = {Physical Sciences Reviews}, volume = {7}, journal = {Physical Sciences Reviews}, number = {10}, publisher = {de Gruyter}, doi = {10.1515/psr-2019-0121}, pages = {1169 -- 1185}, abstract = {The objectives of this work include the analysis of electrical and magnetic properties of magneto-elastic hybrid materials with the intention of developing new techniques for sensor and actuator applications. This includes the investigation of dielectric properties at both low and high frequencies. The behaviour of capacitors whose dielectrics comprise magnetic hybrid materials is well known. Such interfacial magnetocapacitance can be varied according to magnetic content, magnetic flux density and the relative permittivity of the polymer matrix together with other dielectric content. The basic function of trapping electrical charges in polymers (electrets) is also established technology. However, the combination of magnetoactive polymers and electrets has led to the first electromagnetic device capable of adhering to almost any material, whether magnetically susceptible or not. During the course of this research, in addition to dielectrics, electrically conductive polymers based on (PDMS) matrices were developed in order to vary the electrical properties of the material in a targeted manner. In order to ensure repeatable results, this demanded new fabrication techniques hitherto unavailable. The 3D printing of silicones is far from being a mature technology and much pioneering work was necessary before extending the usual 3 d.o.f. to include orientation about and diffusion of particles in these three axes, thus leading to the concept of 6D printing. In 6D printing, the application of a magnetic field can be used during the curing process to control the particulate distribution and thus the spatial filler particle density as desired. Most of the devices (sensors and actuators) produced by such methods contain levels of carbonyl iron powder (CIP) embedded magnetic filler of up to 70 wt\%. Contrary to this, a hitherto neglected research area, namely magnetoactive polymers (MAPs) having significantly lower magnetic particle concentrations (1 to 3 wt\% CIP) were also investigated. With filler concentrations lower than 3 wt\%, structures are formed which are completely absent at higher filler levels. CIP concentrations in the range of 1wt\% demonstrate the formation of toroidal structures. Further development of coherent rings with a compact order results as filler concentrations increase towards 2 wt\%. Above 3 wt\% the structure eventually disintegrates to the usual random order found in traditional MAP with higher CIP content. Structured samples containing 1\%-3 wt\% CIP were investigated with the aid of X-ray tomography where solitary ring structures can be observed and eventually the formation of capillary doubles. Over wavelengths ranging from 1 to 25 µm, spectroscopic analysis of thin film MAP samples containing 2 wt\% CIP revealed measurable magnetic-field-dependent changes in IR absorption at a wavenumber 2350 (λ = 4.255 µm). This was found to be due to the diamagnetic susceptibility of atmospheric carbon dioxide (CO2). Consequently, the first potential application for sparse matrix MAPs was found.}, language = {en} } @inproceedings{GrimmHaumer, author = {Grimm, Alexander and Haumer, Anton}, title = {EMOTH The EMobility Library of OTH Regensburg}, series = {Proceedings of the 12th International Modelica Conference, Prague, Czech Republic, May 15-17, 2017}, booktitle = {Proceedings of the 12th International Modelica Conference, Prague, Czech Republic, May 15-17, 2017}, publisher = {Link{\"o}ping University Electronic Press}, doi = {10.3384/ecp17132285}, pages = {285 -- 290}, abstract = {The importance of E-Mobility is rapidly increasing, not only for private vehicle traffic but also for public transport. In and around Regensburg, Germany there are a lot of automotive companies. Therefore E-Mobility is an important topic in the curriculum of several courses of study at the East-Bavarian Technical University of Applied Sciences Regensburg (OTH). One Master of Applied Research student at OTH has chosen the topic to develop an open-source simulation tool for electric vehicles - the EMOTH Library - based on Modelica and to refine several aspects of the library during the one and a half year of the master course. After one semester, the basic version of the library is available and will be presented in this paper.}, language = {en} } @inproceedings{DiamantidisSykora, author = {Diamantidis, Dimitris and S{\´y}kora, Miroslav}, title = {Implementing Information Gained through Structural Health Monitoring - Proposal for Standards}, series = {13th International Conference on Applications of Statistics and Probability in Civil Engineering, Mai 2019, Seoul, Korea}, booktitle = {13th International Conference on Applications of Statistics and Probability in Civil Engineering, Mai 2019, Seoul, Korea}, abstract = {With exception of a few issues such as design by testing, current standards do not include guidelines on the use and the quantification of value of additional information gained through Structural Health Monitoring (SHM). This contribution summarizes a recently developed draft of the guideline for practicing engineers in the framework of the EU-COST project 1402 and illustrates its application in engineering decision-making. Besides continuous and periodic monitoring, visual inspection, non-destructive evaluation and proof loading are included herein as a simple form of SHM. The guideline is independent of a type of structure, construction materials, loading, and of environmental conditions. It aims at a wide field of application including design of new structures, assessment of existing structures and type specific monitoring of a population of structures. The decision process related to the use of SHM is presented first together with relevant decision objectives and variables. Performance indicators are summarized and discussed with respect to the performance objectives. The evaluation of monitoring strategies based on life cycle costs is exposed and the selection of optimal intervention actions including safety measures is shown in representative case studies. The results demonstrate the potential of the use of monitoring to support engineering decisions and reflect though the practical benefits from the application of the guideline.}, language = {en} } @article{GamischGadererDawoud, author = {Gamisch, Bernd and Gaderer, Matthias and Dawoud, Belal}, title = {On the Development of Thermochemical Hydrogen Storage: An Experimental Study of the Kinetics of the Redox Reactions under Different Operating Conditions}, series = {Applied Sciences}, volume = {11}, journal = {Applied Sciences}, number = {4}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/app11041623}, pages = {1 -- 15}, abstract = {This work aims at investigating the reduction/oxidation (redox) reaction kinetics on iron oxide pellets under different operating conditions of thermochemical hydrogen storage. In order to reduce the iron oxide pellets (90\% Fe2O3, 10\% stabilizing cement), hydrogen (H2) is applied in different concentrations with nitrogen (N2), as a carrier gas, at temperatures between between 700 ∘C and 900 ∘C, thus simulating the charging phase. The discharge phase is triggered by the flow of a mixture out of steam (H2O) and N2 at different concentrations in the same temperature range, resulting in the oxidizing of the previously reduced pellets. All investigations were carried out in a thermo-gravimetric analyzer (TGA) with a flow rate of 250mL/min. To describe the obtained kinetic results, a simplified analytical model, based on the linear driving force model, was developed. The investigated iron oxide pellets showed a stable redox performance of 23.8\% weight reduction/gain, which corresponds to a volumetric storage density of 2.8kWh/(L bulk), also after the 29 performed redox cycles. Recalling that there is no H2 stored during the storage phase but iron, the introduced hydrogen storage technology is deemed very promising for applications in urban areas as day-night or seasonal storage for green hydrogen.}, language = {en} } @article{DechantFedulovFetisovetal., author = {Dechant, Eduard and Fedulov, Feodor and Fetisov, Leonid Y. and Shamonin (Chamonine), Mikhail}, title = {Bandwidth Widening of Piezoelectric Cantilever Beam Arrays by Mass-Tip Tuning for Low-Frequency Vibration Energy Harvesting}, series = {Applied Science}, volume = {7}, journal = {Applied Science}, number = {12}, publisher = {MDPI}, organization = {MDPI AG}, doi = {10.3390/app7121324}, abstract = {Wireless sensor networks usually rely on internal permanent or rechargeable batteries as a power supply, causing high maintenance efforts. An alternative solution is to supply the entire system by harvesting the ambient energy, for example, by transducing ambient vibrations into electric energy by virtue of the piezoelectric effect. The purpose of this paper is to present a simple engineering approach for the bandwidth optimization of vibration energy harvesting systems comprising multiple piezoelectric cantilevers (PECs). The frequency tuning of a particular cantilever is achieved by changing the tip mass. It is shown that the bandwidth enhancement by mass tuning is limited and requires several PECs with close resonance frequencies. At a fixed frequency detuning between subsequent PECs, the achievable bandwidth shows a saturation behavior as a function of the number of cantilevers used. Since the resonance frequency of each PEC is different, the output voltages at a particular excitation frequency have different amplitudes and phases. A simple power-transfer circuit where several PECs with an individual full wave bridge rectifier are connected in parallel allows one to extract the electrical power close to the theoretical maximum excluding the diode losses. The experiments performed on two- and three-PEC arrays show reasonable agreement with simulations and demonstrate that this power-transfer circuit additionally influences the frequency dependence of the harvested electrical power.}, language = {en} } @article{MikhaeilGadererDawoud, author = {Mikhaeil, Makram and Gaderer, Matthias and Dawoud, Belal}, title = {On the development of an innovative adsorber plate heat exchanger for adsorption heat transformation processes; an experimental and numerical study}, series = {Energy}, volume = {207}, journal = {Energy}, number = {September}, publisher = {Elsevier}, doi = {10.1016/j.energy.2020.118272}, pages = {1 -- 13}, abstract = {An innovative adsorber plate heat exchanger (APHE), which is developed for application in adsorption heat pumps, chillers and thermal energy storage systems, is introduced. A test frame has been constructed as a representative segment of the introduced APHE for applying loose grains of AQSOA-Z02. Adsorption kinetic measurements have been carried out in a volumetric large-temperature-jump setup under typical operating conditions of adsorption processes. A transient 2-D model is developed for the tested sample inside the setup. The measured temporal uptake variations with time have been fed to the model, through which a micro-pore diffusion coefficient at infinite temperature of 2 E-4 [m2s-1] and an activation energy of 42.1 [kJ mol-1] have been estimated. A 3-D model is developed to simulate the combined heat and mass transfer inside the APHE and implemented in a commercial software. Comparing the obtained results with the literature values for an extruded aluminium adsorber heat exchanger coated with a 500 μm layer of the same adsorbent, the differential water uptake obtained after 300 s of adsorption (8.2 g/100 g) implies a sound enhancement of 310\%. This result proves the great potential of the introduced APHE to remarkably enhance the performance of adsorption heat transformation appliances.}, language = {en} } @article{HuberHeindlSchlosseretal., author = {Huber, Lea and Heindl, Melanie and Schlosser, Marc and Pfitzner, Arno and Dawoud, Belal}, title = {On the Cycle Stability and Macroscopic Structure of Iron Oxide Pellets for Thermochemical Hydrogen Storage: Influence of Water Content during the Pelletizing Process}, series = {Applied Sciences}, volume = {13}, journal = {Applied Sciences}, number = {11}, publisher = {MDPI}, address = {16}, doi = {10.3390/app13116408}, abstract = {Hydrogen storage based on the repeated reduction and oxidation (redox) reactions of iron oxide/iron composites represents a promising technology. This work is dedicated to studying the influence of the amount of water added during the pelletizing process on the cycle stability and structure of iron oxide pellets. The storage composites were prepared from iron oxide (Fe2O3) and 10 wt.-\% support material (cement) with different amounts of water (18 and 33 wt.-\%) in a laboratory-scale pelletizing disk. To evaluate the cycle stability of the composites, the kinetics of the redox reactions were experimentally measured at 800 ∘ C in an atmosphere of 50\% N2 and 50\% H2 (reduction) or 50\% steam (oxidation), respectively. Moreover, the structure of the pellets was analyzed by micro-computed tomography scans. It turned out that pellets with higher water contents attained faster kinetics and a higher cycle stability. The sample with the least water content (18 wt.-\%) needed about 26 min and 19 min to reach a conversion rate of 80\% during the reduction and oxidation reactions of the sixth redox cycle, respectively. In contrast, the sample with the highest water content (33 wt.-\%) could achieve the same conversion rate after 18 min (reduction) and 13 min (oxidation) during the ninth redox cycle.}, language = {en} } @article{SteiningerGadererDawoud, author = {Steininger, Peter and Gaderer, Matthias and Dawoud, Belal}, title = {Assessment of the Annual Transmission Heat Loss Reduction of a Refurbished Existing Building with an Advanced Solar Selective Thermal Insulation System}, series = {Sustainability}, volume = {13}, journal = {Sustainability}, number = {13}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/su13137336}, pages = {1 -- 19}, abstract = {A numerical parameter sensitivity analysis of the design parameters of the recently published solar selective thermal insulation system (SATIS) has been carried out to enhance its thermal and optical properties. It turned out that the insulation properties of SATIS can be effectively improved by reducing the length of the glass closure element. Increasing the area share of the light conducting elements (LCEs) and decreasing their length-to-diameter (L/D) ratio were identified as key parameters in order to increase the solar gain. Two SATIS variants were compared with the same wall insulation without SATIS in a yearly energetic performance assessment. The SATIS variant with 10 mm length of the closure element, 44.2\% area share of LCE, as well as front and rear diameters of 12 mm/9 mm shows an 11.8\% lower transmission heat loss over the heating period than the wall insulation without SATIS. A new methodology was developed to enable the implementation of the computed solar gains of SATIS in 1D simulation tools. The result is a radiant heat flow map for integration as a heat source in 1D simulation models. A comparison between the 1D and 3D models of the inside wall heat fluxes showed an integral yearly agreement of 98\%.}, language = {en} } @article{BringoutErbFrikel, author = {Bringout, Ga{\"e}l and Erb, Wolfgang and Frikel, J{\"u}rgen}, title = {A new 3D model for Magnetic Particle Imaging using realistic magnetic field topologies for algebraic reconstruction}, series = {Inverse Problems}, volume = {36}, journal = {Inverse Problems}, number = {12}, publisher = {IOP Publishing}, doi = {10.1088/1361-6420/abb446}, abstract = {We derive a new 3D model for magnetic particle imaging (MPI) that is able to incorporate realistic magnetic fields in the reconstruction process. In real MPI scanners, the generated magnetic fields have distortions that lead to deformed magnetic low-field volumes with the shapes of ellipsoids or bananas instead of ideal field-free points (FFP) or lines (FFL), respectively. Most of the common model-based reconstruction schemes in MPI use however the idealized assumption of an ideal FFP or FFL topology and, thus, generate artifacts in the reconstruction. Our model-based approach is able to deal with these distortions and can generally be applied to dynamic magnetic fields that are approximately parallel to their velocity field. We show how this new 3D model can be discretized and inverted algebraically in order to recover the magnetic particle concentration. To model and describe the magnetic fields, we use decompositions of the fields in spherical harmonics. We complement the description of the new model with several simulations and experiments, exploring the effects of magnetic fields distortion and reconstruction parameters on the reconstruction.}, language = {en} } @article{FrazzicaBrancatoDawoud, author = {Frazzica, Andrea and Brancato, Vincenza and Dawoud, Belal}, title = {Unified Methodology to Identify the Potential Application of Seasonal Sorption Storage Technology}, series = {Energies}, volume = {13}, journal = {Energies}, number = {5}, publisher = {MPDI}, address = {Basel}, doi = {10.3390/en13051037}, pages = {1 -- 17}, abstract = {In this study, the definition of a new methodology for a preliminary evaluation of the working boundary conditions under which a seasonal thermal energy storage (STES) system operates is described. The approach starts by considering the building features as well as the reference heating system in terms of solar thermal collectors' technology, ambient heat sinks/source, and space heating distribution systems employed. Furthermore, it is based on a deep climatic analysis of the place where the STES needs to be installed, to identify both winter and summer operating conditions. In particular, the STES energy density is evaluated considering different space heating demands covered by the STES (ranging from 10\% up to 60\%). The obtained results demonstrate that this approach allows for the careful estimation of the achievable STES density, which is varies significantly both with the space heating coverage guaranteed by the STES as well as with the ambient heat source/sink that is employed in the system. This confirms the need for careful preliminary analysis to avoid the overestimation of the STES material volume. The proposed approach was then applied for different climatic conditions (e.g., Germany and Sweden) and the volume of one of the most attractive composite sorbent materials reported in the literature, i.e., multi-wall carbon nanotubes (MWCNT)-LiCl, using water as the working fluid, needed for covering the variable space heating demand in a Nearly Zero Energy Building (NZEB) was calculated. In the case of Swedish buildings, it ranges from about 3.5 m3 when 10\% of the space heating demand is provided by the STES, up to 11.1 m3 when 30\% of the space heating demand is provided by the STES.}, language = {en} } @article{ChatzitakisDawoud, author = {Chatzitakis, Paris and Dawoud, Belal}, title = {An alternative approach towards absorption heat pump working pair screening}, series = {Renewable Energy}, volume = {110}, journal = {Renewable Energy}, publisher = {Pergamon-Elsevier}, organization = {PERGAMON-ELSEVIER SCIENCE LTD}, doi = {10.1016/j.renene.2016.08.014}, pages = {47 -- 58}, abstract = {The successful market penetration of modern absorption heat pumps (AHP) today is critically dependent on their thermodynamic performance as well as other key factors like cost, reliability and inherent safety. Conventional AHPs have a proven record in the first two aspects but crucial shortcomings in the last two. For this reason it has been imperative to search for alternative working pairs that could potentially provide comparable performance while also satisfying the rest of the conditions to the best extent possible. As part of a systematic approach towards this direction, a detailed cycle analysis was performed, utilizing an idealized AHP system containing a real working pair, which enabled the identification of five dimensionless parameters and key thermophysical properties that influence the system's thermodynamic efficiency and the circulation ratio. In order to validate those findings, these parameters were calculated and compared between conventional and alternative AHP refrigerants. It turned out that low molecular weight ratios between absorbent and refrigerant have a beneficial effect on both coefficient of performance and the circulation ratio. Furthermore, both the refrigerant acentric factor and the absorbent vaporization enthalpy shall be minimized to obtain better performance. (C) 2016 Elsevier Ltd. All rights reserved.}, language = {en} } @inproceedings{KrausBrueckl, author = {Kraus, Hermann and Br{\"u}ckl, Oliver}, title = {Automated use of wired measures in grid planning for solving current and voltage band problems}, series = {Power and Energy Student Summit (PESS) 2019, Magdeburg}, volume = {77}, booktitle = {Power and Energy Student Summit (PESS) 2019, Magdeburg}, publisher = {Otto-von-Guericke-Universit{\"a}t, Institut f{\"u}r Elektrische Energiesysteme}, address = {Magdeburg}, isbn = {978-3-944722-84-9}, doi = {10.24352/UB.OVGU-2019-086}, pages = {207 -- 211}, abstract = {This work deals with the use of cable exchange and parallel cabling as network expansion measures in the context of an automated grid planning for the elimination of current and voltage band problems in a distribution network. Inter alia, reference is made to a higher-level program, which is being developed in the EU project "CrossEnergy", and the procedures for remedying the limit value violations are presented.}, subject = {Netzplanung}, language = {en} } @inproceedings{MiedlBraun, author = {Miedl, Christian and Braun, J{\"u}rgen}, title = {Powertrain and electric system design of a 800-volt all-electric car}, series = {European Conference on Nanoelectronics and Embedded Systems for Electric Mobility, eMotion in Smart Cities, 24.-28. September, 2012, Bologna, Italy}, booktitle = {European Conference on Nanoelectronics and Embedded Systems for Electric Mobility, eMotion in Smart Cities, 24.-28. September, 2012, Bologna, Italy}, language = {en} } @article{OstermeierMottokKnorretal., author = {Ostermeier, Daniel and Mottok, J{\"u}rgen and Knorr, Christine and Huber, Michael}, title = {Competence Atlas for Save and Green Road Vehicles in the Electro Mobility Cluster Regensburg}, series = {Applied Research Conference 2012 (ARC 2012) 25./26. June 2012, Nuremberg}, journal = {Applied Research Conference 2012 (ARC 2012) 25./26. June 2012, Nuremberg}, editor = {Mottok, J{\"u}rgen and Ziemann, Olaf}, pages = {86 -- 92}, language = {en} } @inproceedings{Mottok, author = {Mottok, J{\"u}rgen}, title = {Migration path for secure and economic smart power grid devices with transitional smart metering support}, series = {2nd Applied Research Conference 2012 (ARC 2012), 25./26. June 2012, Nuremberg}, booktitle = {2nd Applied Research Conference 2012 (ARC 2012), 25./26. June 2012, Nuremberg}, pages = {64 -- 70}, language = {en} } @inproceedings{NickSchorerMottok, author = {Nick, Matthias and Schorer, Michael and Mottok, J{\"u}rgen}, title = {Feasibility Study of a Build System Performing Automated Builds Based on Model-Based Build Descriptions}, series = {2nd Applied Research Conference 2012 (ARC 2012), 25./26. June 2012, Nuremberg}, booktitle = {2nd Applied Research Conference 2012 (ARC 2012), 25./26. June 2012, Nuremberg}, editor = {Mottok, J{\"u}rgen and Ziemann, Olaf}, publisher = {Shaker}, address = {Aachen}, pages = {71 -- 75}, language = {en} } @inproceedings{SailerDeubzerLuettgenetal., author = {Sailer, Andreas and Deubzer, Michael and L{\"u}ttgen, Gerald and Mottok, J{\"u}rgen}, title = {Comparing Trace Recordings of Automotive Realtime Software}, series = {RTNS '17: Proceedings of the 25th International Conference on Real-Time Networks and Systems, Grenoble, France, IEEE}, booktitle = {RTNS '17: Proceedings of the 25th International Conference on Real-Time Networks and Systems, Grenoble, France, IEEE}, doi = {10.1145/3139258.3139265}, pages = {118 -- 127}, abstract = {The process of engineering models of existing real-time system components is often difficult and time consuming, especially when legacy code has to be re-used or information about the exact timing behaviour is needed. In order to tackle this reverse engineering problem, we have developed the tool CoreTAna. CoreTAna derives an AUTOSAR compliant model of a real-time system by conducting dynamic analysis using trace recordings. Motivated by the challenge of assessing the quality of reverse engineered models of real-time software, we present a novel mathematical measure for comparing trace recordings from embedded real-time systems regarding their temporal behaviour. We also introduce a benchmark framework based on this measure, for evaluating reverse engineering tools such as CoreTAna. This considers common system architectures and also includes randomly generated systems and three systems of industrial automotive projects. Finally, an industrial case study demonstrates other use cases of our measure, such as impact analysis.}, language = {en} } @article{KeimParedesNonnetal., author = {Keim, Vincent and Paredes, Marcelo and Nonn, Aida and M{\"u}nstermann, Sebastian}, title = {FSI-simulation of ductile fracture propagation and arrest in pipelines}, series = {International Journal of Pressure Vessels and Piping}, volume = {182}, journal = {International Journal of Pressure Vessels and Piping}, number = {May}, publisher = {Elsevier}, doi = {10.1016/j.ijpvp.2020.104067}, abstract = {The fracture propagation and arrest control for pipelines transporting rich natural gases and high vapor pressure liquids is based on the Battelle Two-Curve Model (BTCM). Distinct limitations of this model were demonstrated for past and modern steels and gas mixtures. These can be related to the insufficient description of individual physical processes and interactions between the pipe material and transported mixture during the running ductile fracture. In the past, fluid-structure interaction (FSI) models enabled a more sophisticated, coupled analysis of the failure scenario. To quantify their capability of describing the multi-physical processes, the FSI models need to be verified by experimental data from full-scale burst tests (FSBT). Therefore, this paper deals with the simulation of five FSBTs from the literature on API grade X65 pipes with different pipe geometries, mixtures and initial conditions. The FSI is modeled by the coupled Euler-Lagrange (CEL) method. The modified Mohr-Coulomb (MMC) model is implemented in the CEL framework to describe the deformation and ductile fracture in the X65/L450 pipes. 3D Euler equations are used to calculate the mixture decompression with the GERG-2008 equation of state defining the volumetric behavior of a CO2-rich mixture, CH4 and H2. The extended model considers the effect of soil backfill on the pipe deformation and inertia. The numerical predictions agree well with the experimental findings in terms of the crack propagation speed and arrest length underlining the capability of the developed numerical tool.}, subject = {Bruchmechanik}, language = {en} } @inproceedings{NonnKalwa, author = {Nonn, Aida and Kalwa, Christoph}, title = {Analysis of dynamic ductile fracture propagation in pipeline steels}, series = {6th Pipeline Technology Conference (2013), Ostend, Belgium}, booktitle = {6th Pipeline Technology Conference (2013), Ostend, Belgium}, doi = {10.13140/2.1.4370.3046}, abstract = {Analysis of dynamic ductile fracture propagation in pipeline steels: a damage-T IS A WELL-ESTABLISHED fact that the successful application of new generation of high-strength steel grades for long-distance gas transmission depends strongly on full understanding and appropriate characterization of fracture resistance. A damage mechanics approach has found to be a very promising tool in supporting the experimental characterization of ductile fracture propagation. The major advantage of this approach lies in the consideration of the influence of local stress and strain variables on the damage evolution and thus its capability to describe the fracture resistance of the pipelines with different stress triaxiality level by using the same set of parameters. However, the wider application of this approach has been limited due to the issues such as reliable determination of input parameters and required material properties, mesh size dependence, etc.. The objective of this paper is to characterize dynamic ductile fracture resistance of X65 and X80 pipeline materials and to demonstrate the potential of damage mechanics approach for the simulation of dynamic fracture propagation by using two damage models: (1) Cohesive Zone (CZ) model and (2) Gurson-Tvergaard-Needleman (GTN) model. In the first step, results from quasi-static and dynamic tensile tests are used to describe plasticity in terms of flow curves. The calibration of input parameters for both models is performed by using the load-deformation curves from quasi-static tests on non-standard drop-weight tear (DWT) specimens with pre-fatigued crack. b. In the next step, estimated damage model parameters are verified by means of the dynamic tests on the pressed and Chevron notch DWT specimens. Different amounts of crack growth are established by varying the drop height. The experimental fracture resistance is quantified in terms of J-integral at specific crack length. The numerical results are evaluated with respect to global load-deformation and fracture resistance behavior. Furthermore, damage simulations are applied for quantification of local stress conditions in order to identify the major factors controlling the crack propagation. The results reported here serve as a basis for better understanding of fracture performance in dependences of geometry and material properties.}, language = {en} } @inproceedings{NonnKalwa, author = {Nonn, Aida and Kalwa, Christoph}, title = {Failure modeling of pipeline X100 Material in temperature transition region}, series = {22nd International Society of Offshore and Polar Engineering 2012 (ISOPE 2012), Rhodes, Greece}, booktitle = {22nd International Society of Offshore and Polar Engineering 2012 (ISOPE 2012), Rhodes, Greece}, abstract = {This paper focuses on the characterization of the fracture performance of X100 material in transition temperature region using both experimental and numerical methods. The ductile fracture has been analyzed using tests on round notched bar specimens and standard fracture mechanics tests performed at room temperature. In previous publications the damage model Gurson-Tvergaard-Needleman (GTN) has been applied and verified by existing experimental data to describe ductile fracture behavior. The brittle fracture and the fracture in temperature transition region have been studied by means of deep and shallow notched SENB specimens at two different temperatures T=- 80°C and -40°C. Besides elastic-plastic analyses to quantify constraint levels for different initial crack configurations at the onset of cleavage fracture, the brittle failure has been described using modified Beremin model. The influence of the stable crack growth on the cleavage failure probability in temperature transition region has been captured by coupling the ductile fracture model (GTN) with the modified Beremin model. Finally, examples have been presented for the practical application of the numerical results on the fracture assessment of the flawed high-strength pipelines.}, language = {en} } @inproceedings{NonnKalwa, author = {Nonn, Aida and Kalwa, Christoph}, title = {The effect of microstructure, strain hardening and strain rate on the fracture behavior of high strength pipeline steels}, series = {2nd International Conference on Material Modelling (ICMM2), 31th August - 2nd September, 2011 at Mines Paris Tech, France}, booktitle = {2nd International Conference on Material Modelling (ICMM2), 31th August - 2nd September, 2011 at Mines Paris Tech, France}, language = {en} } @inproceedings{NonnKalwa, author = {Nonn, Aida and Kalwa, Christoph}, title = {Application of probabilistic fracture mechanics for safety assessment of longitudinally welded linepipes}, series = {6th Pipeline Technology Conference (2013), Ostend, Belgium}, booktitle = {6th Pipeline Technology Conference (2013), Ostend, Belgium}, language = {en} } @inproceedings{NonnKalwa, author = {Nonn, Aida and Kalwa, Christoph}, title = {Application of damage mechanics approach for crack propagation in pipeline}, series = {19th Biennial Joint Technical Meeting (JTM) on Pipeline Research, April 29 - May 3, 2013, Sydney, Australia}, booktitle = {19th Biennial Joint Technical Meeting (JTM) on Pipeline Research, April 29 - May 3, 2013, Sydney, Australia}, language = {en} } @inproceedings{NonnErdelenPepplerWesseletal., author = {Nonn, Aida and Erdelen-Peppler, Marion and Wessel, Waldemar and Mahn, Denise}, title = {How reliable are the current testing procedures for the safety assurance against crack propagation in seamless gas pipelines}, series = {Proceedings of the ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering (OMAE2014), Volume 4A: Structures, Safety and Reliability, June 8-13, 2014, San Francisco, USA}, booktitle = {Proceedings of the ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering (OMAE2014), Volume 4A: Structures, Safety and Reliability, June 8-13, 2014, San Francisco, USA}, doi = {10.13140/2.1.3190.6567}, abstract = {The worldwide growing energy demand with the exploration of new gas fields has promoted the development of high toughness seamless pipeline steels which should sustain the increasing demands resulting from the complex loading situations. One of the most important prerequisites for safe installation and operation of long distance gas transmission pipelines is the detailed knowledge and characterization of their fracture performance for specific applications. However, recent industry experience has revealed concerns related to the limitations and reliability of current test methods for brittle-to-ductile transition evaluation. Regarding the transition temperature evaluation, the critical issues involve Drop-Weight Tear Testing (DWTT) and full-scale West-Jefferson (WJ) test applied to the smaller pipes with diameter less than 500mm. The DWTT leads frequently to invalid results in terms of abnormal fracture appearance and inverse fracture occurrence. It is still not clear if this behavior is only owed to a testing effect, which material characteristics cause it and how far it reflects the full-scale behavior. Similar observations were made for the West-Jefferson tests, which could not be assessed in the standard manner either. Again, the question was towards testing effects and the behavior of the pipeline transporting gaseous media remains unanswered. Therefore, this paper aims at identifying open questions on basis of a literature study and own experimental results and showing possible ways forward in demonstrating safety in design against propagating fracture.}, language = {en} } @inproceedings{NonnWesselSchmidt, author = {Nonn, Aida and Wessel, Waldemar and Schmidt, Tanja}, title = {Application of finite element analysis for assessment of fracture behavior of modern high toughness seamless pipeline steels}, series = {23rd International Society of Offshore and Polar Engineering 2013 (ISOPE 2013), Anchorage, USA}, booktitle = {23rd International Society of Offshore and Polar Engineering 2013 (ISOPE 2013), Anchorage, USA}, doi = {10.13140/2.1.4239.2322}, abstract = {Fracture behavior of seamless pipeline material X65Q acc. to API 5L has been studied both experimentally and numerically at different loading conditions (quasi-static vs. dynamic) and temperatures. The recent findings have shown difficulties in applying well established methods for determination of transition behavior or prediction of ductile crack arrest for the new generation of high-toughness steels. The irregular fracture performance (e.g. so-called "abnormal inverse fracture" appearance, significant scattering in ductile-to-brittle-transition-temperature region, etc.) suggests that the influence of pipe dimensions, loading parameters, crack initiation resistance as well as testing procedure on the fracture behavior has been neither understood nor properly described. This work aims to shed light on these questions regarding the applicability of conventional methods and to better illuminate most relevant parameters affecting fracture behavior of high toughness steels. To achieve this goal, experimental data basis for analysis of fracture behavior in transition and upper shelf regime has been established by conducting quasi-static fracture mechanics tests and dynamic tests on Battelle Drop Weight Tear (BDWT or DWT) specimens at different temperatures. The evaluation of obtained test results in upper shelf has been additionally complemented by numerical simulation of damage behavior. The results highlight the influence of stress conditions on fracture behavior with reference to pipe dimensions and loading conditions and, subsequently, may be used as a basis for revision of existing design methods.}, subject = {Rissfortschritt}, language = {en} }