@inproceedings{Haumer, author = {Haumer, Anton}, title = {Modeling and Control Design of an Educational Magnetic Levitation System}, series = {Proceedings of the 15th International Modelica Conference 2023, Aachen, October 9-11}, booktitle = {Proceedings of the 15th International Modelica Conference 2023, Aachen, October 9-11}, publisher = {Link{\"o}ping University Electronic Press}, issn = {1650-3686}, doi = {10.3384/ecp204763}, abstract = {A magnetic levitation system is a perfect educational example of a nonlinear unstable system. Only with suitable control, a small permanent magnet can be held floating stable below a coil. After modeling and simulation of the system, control of the system can be developed. At the end, the control algorithm can be coded on a microcontroller, connected to a pilot plant.}, language = {en} } @inproceedings{GrauvoglStauderHopfenspergeretal., author = {Grauvogl, Dominik and Stauder, Peter and Hopfensperger, Bernhard and Gerling, Dieter}, title = {Multiphysics Design of a Wound Field Synchronous Machine with Magnetic Asymmetry}, series = {Proceedings of the 2021 IEEE International Electric Machines \& Drives Conference (IEMDC): 17-20 May 2021, Hartford, CT, USA}, booktitle = {Proceedings of the 2021 IEEE International Electric Machines \& Drives Conference (IEMDC): 17-20 May 2021, Hartford, CT, USA}, doi = {10.1109/IEMDC47953.2021.9449564}, abstract = {In this paper a multiphysics development method is used for designing a novel wound field synchronous machine of the future generation of high voltage traction drives. This method covers the domains of electromagnetics, the mechanical strength, thermal behavior and the magnetic noise. It is shown that the proposed novel asymmetric design with a circular flux barrier in combination with an asymmetric pole offset is fulfilling the requirements according to performance and torque ripple. A fatigue strength rotor mechanic concept is included. A hybrid cooling concept consisting of a water jacket cooled stator and air cooled rotor ensures the needed continuous power. Unacceptable noise levels are excluded by investigating the equivalent radiated power (ERP) level due to radial forces in the air gap. Finally, the multi-physical workflow resulted in a fully developed component with a high degree of maturity.}, language = {en} } @inproceedings{GrauvoglKrabinskiStauderetal., author = {Grauvogl, Dominik and Krabinski, Jeffrey and Stauder, Peter and Hopfensperger, Bernhard and Gerling, Dieter}, title = {NVH Comparison of a Novel Wound Field Synchronous Machine with Magnetic Asymmetry with a PSM for a HV Electric Drive}, series = {2021 JSAE Annual Congress (Spring) Proceedings; online meeting (No.76-21)}, booktitle = {2021 JSAE Annual Congress (Spring) Proceedings; online meeting (No.76-21)}, publisher = {JSAE}, abstract = {This paper shows how magnetic noises can be reduced with a wound field synchronous machine (WFSM) with magnetic asymmetry compared to a permanent magnet synchronous machine (PSM), operating at base speed range and full load. In order to reproduce a real noise behavior, the two rotor types are operated in a complete electric drive unit (EDU) consisting of an electric motor, gearbox, inverter and overall housing. In the concept study, the noise characteristics of the two electric machines is evaluated and compared via mechanical finite element method (FEM) simulations using the equivalent radiated power (ERP) level and Campbell diagrams. Furthermore, it is shown that critical frequency orders can already be identified by the analysis of the magnetic force density from the electromagnetic design without computationally intensive ERP calculations. In this context, the ERP investigations have shown that the unique feature of the magnetically asymmetric WFSM is the reduction of the slot harmonics. At the current state of the art, the slot harmonics can only be reduced with a rotor skewing. The disadvantage of this is a reduction in performance and a more expensive production. It is also remarkable that the magnetic asymmetry reduces the slot harmonics more than the rotor skewing in the PSM. In addition, both machines are still considered with a short-pitched stator winding to optimize the overall noise level by reducing the 24th frequency order.}, subject = {Elektroantrieb}, language = {en} } @article{GaertnerRankHeberletal., author = {G{\"a}rtner, Sebastian and Rank, Daniel and Heberl, Michael and Gaderer, Matthias and Dawoud, Belal and Haumer, Anton and Sterner, Michael}, title = {Simulation and Techno-Economic Analysis of a Power-to-Hydrogen Process for Oxyfuel Glass Melting}, series = {Energies}, volume = {14}, journal = {Energies}, number = {24}, publisher = {MDPI}, doi = {10.3390/en14248603}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-22713}, abstract = {As an energy-intensive industry sector, the glass industry is strongly affected by the increasingly stringent climate protection targets. As established combustion-based production systems ensure high process stability and glass quality, an immediate switch to low greenhouse gas emission processes is difficult. To approach these challenges, this work investigates a step-by-step integration of a Power-to-Hydrogen concept into established oxyfuel glass melting processes using a simulation approach. This is complemented by a case study for economic analysis on a selected German glass industry site by simulating the power production of a nearby renewable energy park and subsequent optimization of the power-to-hydrogen plant performance and capacities. The results of this study indicate, that the proposed system can reduce specific carbon dioxide emissions by up to 60\%, while increasing specific energy demand by a maximum of 25\%. Investigations of the impact of altered combustion and furnace properties like adiabatic flame temperature (+25 °C), temperature efficiency (∆ξ = -0.003) and heat capacity flow ratio (∆zHL = -0.009) indicate that pure hydrogen-oxygen combustion has less impact on melting properties than assumed so far. Within the case study, high CO2 abatement costs of 295 €/t CO2-eq. were determined. This is mainly due to the insufficient performance of renewable energy sources. The correlations between process scaling and economic parameters presented in this study show promising potential for further economic optimization of the proposed energy system in the future.}, language = {en} } @inproceedings{HopfenspergerDaubnerHerrmannetal., author = {Hopfensperger, Bernhard and Daubner, Andreas and Herrmann, Fabian and Hopkins, Andrew and Mellor, Phil}, title = {Investigation of Shifted PWM Methods for a Dual Three-Phase System to Reduce Capacitor RMS Current}, series = {PCIM Europe Digital Days 2020: International Exhibition and Conference for Power Electronics, Intelligent Motion, Renewable Energy and Energy Management: 07.-08.07.2020, Online [proceedings]}, booktitle = {PCIM Europe Digital Days 2020: International Exhibition and Conference for Power Electronics, Intelligent Motion, Renewable Energy and Energy Management: 07.-08.07.2020, Online [proceedings]}, publisher = {VDE-Verlag}, address = {Berlin, Offenbach}, isbn = {978-3-8007-5245-4}, pages = {124 -- 131}, abstract = {Mild hybrid automotive topologies containing a 48V high power (>15 kW) electric drive system demand a high integration of power electronics and electrical machine. A multi-phase motor winding topology helps to keep the per-phase operating currents to a reasonable level. Close integration and multi-phase system have led to a drive system with dual 3-phase systems supplied by a common 48V DC-link, which allows to shift PWM patterns for reduction of DC-link capacitor ripple current and size. This paper derives some basic rules for combinations of common PWM methods for dual 3-phase systems without magnetic cross-coupling. Experimental measurements verify simulated results.}, subject = {Elektroantrieb}, language = {en} } @inproceedings{HopkinsHopfenspergerMellor, author = {Hopkins, Andrew and Hopfensperger, Bernhard and Mellor, Phil}, title = {DC-link Capacitor Reduction in Low Voltage and High Power Integrated Modular Motor Drives}, series = {2019 IEEE Energy Conversion Congress and Exposition (ECCE), 29 Sept.-3 Oct. 2019, Baltimore, MD, USA}, booktitle = {2019 IEEE Energy Conversion Congress and Exposition (ECCE), 29 Sept.-3 Oct. 2019, Baltimore, MD, USA}, doi = {10.1109/ECCE.2019.8913213}, pages = {3208 -- 3214}, abstract = {The development of 48V high power (>15 kW) automotive propulsion drives demands close integration of the power electronics and the electrical machine. Due to the large operating currents distributed multi-phase topologies are needed and physically separating the power converter from the e-machine would involve heavy cabling and costly connections. The volume and cost of the filter capacitor represents a major challenge in closely integrated high power integrated modular motor drives and techniques are needed to minimize this. The DC-link capacitor requires a large ripple current handling capability and cost, size and reliability limitations result in suitable candidate technologies being those with low volumetric energy densities. Use of interleaved multi three-phase machines are attractive due to the associated capacitor ripple current reduction. Discontinuous modulation schemes may also be employed as a technique for reducing the current ripple. In this paper techniques for capacitor ripple reduction are assessed through simulation and compared.}, language = {en} } @inproceedings{BrkicCeranElmoghazyetal., author = {Brkic, Jovan and Ceran, Muaz and Elmoghazy, Mohamed and Kavlak, Ramazan and Haumer, Anton and Kral, Christian}, title = {Open Source PhotoVoltaics Library for Systemic Investigations}, series = {Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany}, booktitle = {Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany}, publisher = {Link{\"o}ing University Electronic Press}, doi = {10.3384/ecp1915741}, pages = {41 -- 50}, abstract = {For the planning of photovoltaic power plants standard software tools are used. Most of these software tools use statistical solar data to determine the overall energy harvest of a photovoltaic plant over one year. The calculations rely on stationary location and ideal boundary conditions, e.g., constant ambient temperature. Even though, for example, shadowing may be considered by standard software, the investigation of untypical configurations and problems cannot be performed by such software, as most configurations cannot be changed by the user. The presented PhotoVoltaics library was developed with the intention to provide a flexible framework for standard and non-standard problems. Particularly, the PhotoVoltaics library can be coupled with other Modelica libraries to perform systemic investigations. An application library, PhotoVoltaics_TGM, is provided as add-on, where measured data of two photovoltaic pants of the TGM in Vienna can be compared with simulation results. This add-on library serves as validation of the PhotoVoltaics library.}, language = {en} } @inproceedings{AlexanderHaumer, author = {Alexander, Grimm and Haumer, Anton}, title = {Parametrization Of A Simplified Physical Battery Model}, series = {Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany}, booktitle = {Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany}, publisher = {Link{\"o}ing University Electronic Press}, doi = {10.3384/ecp19157215}, pages = {215 -- 220}, abstract = {The importance of batteries is increasing, especially in the field of the high power requirement systems like electric driven vehicles. Mobile energy storage makes it possible to accelerate with incredible torque, without any accruing air pollution. Due to the high costs of real components, it is of great use to simulate battery driven systems before building them. Transient processes within a cell are highly dependent on the operating point of the complete system, which makes it difficult to create equations and model arameterizations. This paper shows which data is important for cell modeling and how to parameterize simplified physical cell models.}, language = {en} } @inproceedings{GrimmHaumer, author = {Grimm, Alexander and Haumer, Anton}, title = {EMOTH The EMobility Library of OTH Regensburg}, series = {Proceedings of the 12th International Modelica Conference, Prague, Czech Republic, May 15-17, 2017}, booktitle = {Proceedings of the 12th International Modelica Conference, Prague, Czech Republic, May 15-17, 2017}, publisher = {Link{\"o}ping University Electronic Press}, doi = {10.3384/ecp17132285}, pages = {285 -- 290}, abstract = {The importance of E-Mobility is rapidly increasing, not only for private vehicle traffic but also for public transport. In and around Regensburg, Germany there are a lot of automotive companies. Therefore E-Mobility is an important topic in the curriculum of several courses of study at the East-Bavarian Technical University of Applied Sciences Regensburg (OTH). One Master of Applied Research student at OTH has chosen the topic to develop an open-source simulation tool for electric vehicles - the EMOTH Library - based on Modelica and to refine several aspects of the library during the one and a half year of the master course. After one semester, the basic version of the library is available and will be presented in this paper.}, language = {en} } @inproceedings{HaumerKral, author = {Haumer, Anton and Kral, Christian}, title = {Enhancements of Electric Machine Models: The EMachines Library}, series = {Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015}, volume = {118}, booktitle = {Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015}, publisher = {Link{\"o}ping University Electronic Press}, doi = {10.3384/ecp15118509}, pages = {509 -- 515}, abstract = {Transient models of multi phase electric machines are already implemented in the Modelica Standard Library (MSL). However, advanced effects like saturation and skin effect are not taken into account. As an extension to the MSL models, the new EMachines library is presented. This package will be released as a supplemental library to the commercial EDrives library. The particular focus of this paper is on the deep bar effect of induction machines. A comparison of simulation results demonstrates the influence of the skin effect on the operational behavior of the machines. At the end of this publication further developments of the EMachines library will be outlined.}, language = {en} } @inproceedings{EberhartChungHaumeretal., author = {Eberhart, Philip and Chung, Tek Shan and Haumer, Anton and Kral, Christian}, title = {Open Source Library for the Simulation of Wind Power Plants}, series = {Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015}, booktitle = {Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015}, address = {Link{\"o}ping}, doi = {10.3384/ecp15118929}, pages = {929 -- 936}, abstract = {This paper presents the new open source Modelica libraryWindPowerPlants. For the economic assessment of either a wind power plant or an entire wind park, the accurate prediction of the energy output is essential. Such prediction is usually performed by means of calculations based on statistical wind data. The proposed WindPowerPlants library is capable of assessing the energy output both for statistical and real wind data based on time domain simulations. In the presented version of the library wind turbine models are modeled with pitch control. The generator models have variable speed and an optional connector to the mains. The entire library is based on power balance conditions and losses are fully neglected. Yet, the library can be extended towards more detailed models considering different types of losses. The structure and components of the library are presented. Simulations examples are shown and compared with reference data. The applicability of the proposed WindPowerPlants library is demonstrated and possible enhancements are discussed.}, language = {en} } @article{KralHaumerLee, author = {Kral, Christian and Haumer, Anton and Lee, Sang Bin}, title = {A Practical Thermal Model for the Estimation of Permanent Magnet and Stator Winding Temperatures}, series = {IEEE Transactions on Power Electronics}, volume = {29}, journal = {IEEE Transactions on Power Electronics}, number = {1}, publisher = {IEEE}, issn = {1941-0107}, doi = {10.1109/TPEL.2013.2253128}, pages = {455 -- 464}, abstract = {A thermal model for the determination of the temperatures of interior permanent magnets and stator windings is presented in this paper. The innovation of the model relies on one temperature sensor being located in the stator core of the machine. Such sensor is simple to implement in many applications such as traction or EV, where reliability is critical. The estimated stator winding and permanent magnet temperatures are determined by a simplified thermal lumped element network model with only two time constants. It is shown that the proposed thermal model is very robust due to the structure of the model and the measured stator core temperature. The distortion of the temperature estimates caused by the cooling circuit is inherently accounted for such that the model can be used for robust online prediction of temperatures. Experimental results based on a forced water-cooled interior permanent magnet synchronous machine setup are presented to validate the effectiveness of the presented model.}, language = {en} } @inproceedings{KralHaumerWoehrnschimmel, author = {Kral, Christian and Haumer, Anton and W{\"o}hrnschimmel, Reinhard}, title = {Extension of the FundamentalWave Library towards Multi Phase Electric Machine Models}, series = {Proceedings of the 10th International Modelica Conference, March 10-12, 2014, Lund, Sweden}, booktitle = {Proceedings of the 10th International Modelica Conference, March 10-12, 2014, Lund, Sweden}, publisher = {Link{\"o}ping University Electronic Press}, isbn = {978-91-7519-380-9}, issn = {1650-3686}, doi = {10.3384/ecp14096135}, pages = {135 -- 143}, abstract = {Abstract Electric machine theory and electric machine simulations models are often limited to three phases. Up to the Modelica Standard Libray (MSL) version 3.2 the provided machine models were limited to three phases. Particularly for large industrial drives and for redundancy reasons in electric vehicles and aircrafts multi phase electric machines are demanded. In the MSL 3.2.1 an extension of the existing FundamentalWave library has been performed to cope with phase numbers greater than or equal to three. The developed machine models are fully incorporating the multi phase electric; magnetic; rotational and thermal domain. In this publication the theoretical background of the machines models; Modelica implementation details; the parametrization of the models and simulation examples are presented.}, language = {en} } @inproceedings{HaumerKral, author = {Haumer, Anton and Kral, Christian}, title = {The New EDrives Library: A Modular Tool for Engineering of Electric Drives}, series = {Proceedings of the 10th International Modelica Conference, March 10-12, 2014, Lund, Sweden}, booktitle = {Proceedings of the 10th International Modelica Conference, March 10-12, 2014, Lund, Sweden}, publisher = {Link{\"o}ping University Electronic Press}, isbn = {978-91-7519-380-9}, issn = {1650-3686}, doi = {10.3384/ecp14096155}, pages = {155 -- 163}, abstract = {Simulation is an indispensable tool for the engineering of systems containing electric drives. Depending on the design phase and the engineering task different levels of modeling details are required: proof of concept; investigation of energy and power consumption; design of control; etc. The new EDrives library provides three levels of abstraction for inverters: quasi static (neglecting electrical transients); averaging (neglecting switching effects) and switching - for serving different demands. The inverters can feed the machine models of the Modelica Standard Library: Modelica.Magnetic.FundamentalWave and the new Modelica.Magnetic.QuasiStatic.FundamentalWave. The EDrives library copes with arbitrary phase numbers and can be easily extended to develop new control algorithms. In this publication the structure of the library and the implemented control principles are presented. Furthermore; examples comparing the three different levels of abstraction are included.}, language = {en} } @article{HaumerKralVukovicetal., author = {Haumer, Anton and Kral, Christian and Vukovic, Vladimir and David, Alexander and Hettfleisch, Christian and Huzsvar, Attila}, title = {A Parametrization Scheme for High Performance Thermal Models of Electric Machines using Modelica}, series = {IFAC Proceedings Volumes}, volume = {45}, journal = {IFAC Proceedings Volumes}, number = {2}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1474-6670}, doi = {10.3182/20120215-3-AT-3016.00187}, pages = {1058 -- 1062}, abstract = {Thermal models offer great advantages for enhancement of design, protection and control of electric machines. Detailed thermal models take a great number of time constants into account and provide accurate prediction of the temperatures. However, to parameterize such models detailed geometric data are needed. Whenever such detailed information is not available, or the performance of the detailed models is not satisfying, simplified thermal models as described in this paper are advantageous. The calculation of parameters is described in detail, in order to achieve best accordance with temperatures obtained from measurements or from simulations with detailed thermal models. Thermal resistances are calculated from end temperatures of a test run with constant load (and known losses). Thermal capacitances are obtained using optimization to minimize deviation of simulated and measured temperatures during the whole test run. The thermal model of an asynchronous induction machine with squirrel cage is coupled with an electrical model of the drive. For validation, simulation results of an optimally parameterized simplified model are compared with temperatures obtained by simulation of a detailed thermal model, which in turn has been validated against measurement results, both for continuous duty S1 and intermittent duty S6 (6 minutes no-load followed by 4 minutes of 140\% nominal load). The deviations are not more than 4 K which is quite satisfying.}, language = {en} } @inproceedings{BogomolovKralHaumeretal., author = {Bogomolov, Maxim and Kral, Christian and Haumer, Anton and Lomonova, Elena}, title = {Modeling of permanent magnet synchronous machine with fractional slot windings}, series = {Proceedings IECON 2012 - 38th Annual Conference on IEEE Industrial Electronics Society ; Ecole de Technologie Superieure de Montreal, Universite du Quebec Montreal, Canada 25 - 28 October, 2012}, booktitle = {Proceedings IECON 2012 - 38th Annual Conference on IEEE Industrial Electronics Society ; Ecole de Technologie Superieure de Montreal, Universite du Quebec Montreal, Canada 25 - 28 October, 2012}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-4673-2421-2}, issn = {1553-572X}, doi = {10.1109/IECON.2012.6388912}, pages = {1894 -- 1899}, abstract = {This paper focuses on simulation of permanent magnet synchronous machine (PMSM) with fractional-slot windings (FSW) in Modelica. Modeling of the electrical machines with object-oriented approach is shortly described, and a new Modelica library for simulation of electrical machines is introduced. The results of simulation of PMSMs with fractional slot windings are presented and explained. Special attention is paid to the higher harmonics and subharmonics produced by the winding and their influence on machine operation.}, language = {en} } @inproceedings{HaumerKral, author = {Haumer, Anton and Kral, Christian}, title = {Motor Management of Permanent Magnet Synchronous Machines}, series = {Proceedings of the 9th International MODELICA Conference; September 3-5; 2012; Munich; Germany}, booktitle = {Proceedings of the 9th International MODELICA Conference; September 3-5; 2012; Munich; Germany}, editor = {Otter, Martin and Zimmer, Dirk}, publisher = {Link{\"o}ping University Electronic Press}, isbn = {978-91-7519-826-2}, issn = {1650-3686}, doi = {10.3384/ecp12076159}, pages = {159 -- 166}, abstract = {Two state-of-the-art machine designs are mainly used in recent electric and hybrid electric vehicles: asynchronous induction machines with squirrel cage which are robust but need a current component to excite the magnetic field; and permanent magnet synchronous machines which rely on somehow more sensible parts but the magnets are able to excite a magnetic field without current. However; if speed gets high enough to reach the field weakening range; for both machine the field oriented control has to prescribe a field current sufficient to reduce the field not to exceed the voltage limits of the stator circuit. Especially for the permanent magnet synchronous machine this paper investigates whether it is possible to determine an optimal field current for every operation point to minimize either total current consumption or losses.}, language = {en} } @inproceedings{KralHaumerBogomolovetal., author = {Kral, Christian and Haumer, Anton and Bogomolov, Maxim and Lomonova, Elena}, title = {Harmonic wave model of a permanent magnet synchronous machine for modeling partial demagnetization under short circuit conditions}, series = {2012 XXth International Conference on Electrical Machines (ICEM 2012) ; Marseille, France, 2 - 5 September 2012}, booktitle = {2012 XXth International Conference on Electrical Machines (ICEM 2012) ; Marseille, France, 2 - 5 September 2012}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-4673-0142-8}, doi = {10.1109/ICElMach.2012.6349880}, pages = {295 -- 301}, abstract = {This paper proposes a multi domain physical model of permanent magnet synchronous machines, considering electrical, magnetic, thermal and mechanical effects. For each component of the model, the main wave as well as lower and higher harmonic wave components of the magnetic flux and the magnetic potential difference may be considered. The permanent magnets are modeled as discrete azimuthal segments in order to consider possible partial demagnetization effects. For each magnet segment a linearized temperature dependent B-H curve is considered. The main advantage of the presented model is that time transient operational behavior of a permanent magnet synchronous machine can be considered under various electrical, magnetic, thermal and mechanical conditions. The electromagnetic condition of surface magnet machine is compared with finite element analysis.}, language = {en} } @inproceedings{KralHaumerLee, author = {Kral, Christian and Haumer, Anton and Lee, Sang Bin}, title = {Robust thermal model for the estimation of rotor cage and stator winding temperatures of induction machines}, series = {2012 XXth International Conference on Electrical Machines ; Marseille, France, 02.- 05.09.2012}, booktitle = {2012 XXth International Conference on Electrical Machines ; Marseille, France, 02.- 05.09.2012}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-4673-0142-8}, doi = {10.1109/ICElMach.2012.6350127}, pages = {1810 -- 1816}, abstract = {In this paper a new model for the estimation of the stator winding and rotor cage temperatures of induction machines is presented. This model can be used in series applications of machines operated under dynamic load conditions where stator and rotor temperature shall be monitored. The proposed model relies on a simplified lumped element thermal equivalent circuit model where the stator core temperature serves as input quantity. The great advantage of this model is that it covers ambient and cooling conditions inherently. This leads to great simplicity and robustness. The parametrization and validation of the model through experimental data is presented. Advantages, drawbacks and possible implementations are discussed.}, language = {en} } @inproceedings{KralHaumerLee, author = {Kral, Christian and Haumer, Anton and Lee, Sang Bin}, title = {Innovative thermal model for the estimation of permanent magnet and stator winding temperatures}, series = {2012 IEEE Energy Conversion Congress and Exposition (ECCE 2012) ; Raleigh, NC, USA 15.09.-20.09.2012}, booktitle = {2012 IEEE Energy Conversion Congress and Exposition (ECCE 2012) ; Raleigh, NC, USA 15.09.-20.09.2012}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-4673-0803-8}, issn = {2329-3721}, doi = {10.1109/ECCE.2012.6342386}, pages = {2704 -- 2711}, abstract = {In this paper an innovative thermal model for the determination of the temperatures of the permanent magnets and stator windings is presented. This model relies on one temperature sensor located in the stator core of the machine. The estimated stator winding and permanent magnet temperatures are determined by a simplified thermal lumped element network model with only two time constants. Due to the structure of the model and the measured stator core temperature the proposed thermal model is very robust. Distortion of the cooling circuit are inherently sensed such that the model can be used for the online prediction of temperatures. Experimental results based on an interior permanent magnet synchronous machine are presented to validate the presented model.}, language = {en} } @inproceedings{BaeumlHaumerKapelleretal., author = {B{\"a}uml, T. and Haumer, Anton and Kapeller, H. and Starzinger, J. and Farzi, P.}, title = {Impact of inverter pulse inhibition on the high-voltage supply system of an electric vehicle — A simulative approach}, series = {2011 IEEE Vehicle Power and Propulsion Conference (VPPC 2011) : Powering sustainable transportation ; Chicago, Illinois, USA, 06. - 09.09.2011}, booktitle = {2011 IEEE Vehicle Power and Propulsion Conference (VPPC 2011) : Powering sustainable transportation ; Chicago, Illinois, USA, 06. - 09.09.2011}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-61284-248-6}, doi = {10.1109/VPPC.2011.6043159}, pages = {1 -- 5}, abstract = {This paper deals with a simulative approach for investigating the impact of inverter pulse inhibition during field weakening operation of permanent magnet synchronous machines and asynchronous induction machines. The modelling and simulation language Modelica is used to design models for the vehicle, the electric machine and the inverter in different abstraction levels. It is shown that when using a permanent magnet synchronous machine, a sudden breakdown of the field weakening current causes induction of high voltages in the stator windings. Hence, the electric system of the vehicle has to be protected against the resulting high currents. Furthermore precautions have to be taken to avoid dangerous driving conditions because of high braking torques in an inverter fault operation mode. In the case of the asynchronous induction machine an inverter pulse inhibition poses no big problem, neither for the electric system of the vehicle, nor the driver.}, language = {en} } @inproceedings{HongHyunKangetal., author = {Hong, Jongman and Hyun, Doosoo and Kang, Tae-june and Lee, Sang Bin and Kral, Christian and Haumer, Anton}, title = {Detection and classification of rotor demagnetization and eccentricity faults for PM synchronous motors}, series = {2011 IEEE Energy Conversion Congress and Exposition (ECCE 2011) : Energy conversion innovation for a clean energy future ; Phoenix, Arizona, USA, 17.-22.09.2011}, booktitle = {2011 IEEE Energy Conversion Congress and Exposition (ECCE 2011) : Energy conversion innovation for a clean energy future ; Phoenix, Arizona, USA, 17.-22.09.2011}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-4577-0542-7}, issn = {2329-3721}, doi = {10.1109/ECCE.2011.6064103}, pages = {2512 -- 2519}, abstract = {Condition monitoring of rotor problems such as demagnetization and eccentricity in permanent magnet synchronous motors (PMSM) is essential for guaranteeing high motor performance, efficiency, and reliability. However, there are many limitations to the off-line and on-line methods currently used for PMSM rotor quality assessment. In this paper, an inverter-embedded technique for automated detection and classification of PMSM rotor faults is proposed as an alternative. The main concept is to use the inverter to perform a test whenever the motor is stopped, to detect rotor faults independent of operating conditions or load torque oscillations, which is not possible with motor current signature analysis (MCSA). The d-axis is excited with a dc+ac signal, and the variation in the inductance pattern due to the change in the degree of magnetic saturation caused by demagnetization or eccentricity is observed for fault detection. An experimental study on a 7.5kW PMSM verifies that demagnetization and eccentricity can be detected and classified independent of the load with high sensitivity.}, language = {en} } @inproceedings{HongLeeKraletal., author = {Hong, Jongman and Lee, Sang Bin and Kral, Christian and Haumer, Anton}, title = {Detection of airgap eccentricity for permanent magnet synchronous motors based on the d-axis inductance}, series = {8th IEEE International Symposium on Diagnostics for Electric Machines, Power Electronics \& Drives (SDEMPED), 2011 // 05. - 08.09.2011, Bologna, Italy}, booktitle = {8th IEEE International Symposium on Diagnostics for Electric Machines, Power Electronics \& Drives (SDEMPED), 2011 // 05. - 08.09.2011, Bologna, Italy}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-4244-9301-2}, doi = {10.1109/DEMPED.2011.6063651}, pages = {378 -- 384}, abstract = {The majority of the work performed for detecting eccentricity faults for permanent magnet synchronous motors (PMSM) focus on motor current signature analysis (MCSA), as it provides continuous on-line monitoring with existing current sensors. However, MCSA cannot be applied under nonstationary conditions and cannot distinguish faults with load torque oscillations, which are limitations for many PMSM drive applications. In this paper, it is shown that the d-axis inductance, L d , decreases with increase in the severity of eccentricity due to the change in the degree of magnetic saturation, and it is proposed as a new fault indicator. The inverter can be used to perform a standstill test automatically whenever the motor is stopped, to measure L d for eccentricity testing independent of load variations or oscillations, which is not possible with MCSA. An FE and experimental study on a 10hp PMSM verifies that eccentricity can be detected independent of the load with high sensitivity and reliability.}, language = {en} } @inproceedings{HaumerKral, author = {Haumer, Anton and Kral, Christian}, title = {Modeling a Mains connected PWM Converter with Voltage-Oriented Control}, series = {Proceedings of the 8th International Modelica Conference, Technical Univeristy, Dresden, Germany, 20.-22.03.2011}, booktitle = {Proceedings of the 8th International Modelica Conference, Technical Univeristy, Dresden, Germany, 20.-22.03.2011}, publisher = {Link{\"o}ping University Electronic Press}, doi = {10.3384/ecp11063388}, pages = {388 -- 397}, abstract = {The majority of industrial controlled induction machine drives are connected to the mains via a diode bridge. However; if reduction of harmonic currents and / or regenerative operation is desired; replacing the diode bridge by an active front-end (AFE) is required. This paper describes two models of an AFE: a power balance model disregarding switching effects; and an ideal switching model of a pulse width modulation (PWM) converter. Both models are controlled utilizing space phasors in a voltage oriented reference frame. Voltage oriented control (VOC) of the mains converter can be compared with field oriented control (FOC) of a machine converter. Design and parametrization of the main parts—synchronization with mains voltage; current controller and DC voltage controller—are described in detail. Additionally; simulation results proving the implementation and demonstrating possible investigations as well as an outlook on further enhancements are presented.}, language = {en} } @inproceedings{JungreuthmayerBaumlWinteretal., author = {Jungreuthmayer, C. and Bauml, T. and Winter, O. and Ganchev, M. and Kapeller, H. and Haumer, Anton and Kral, Christian}, title = {Heat and fluid flow analysis of an internal permanent magnet synchronous machine by means of computational fluid dynamics}, series = {2011 IEEE International Electric Machines \& Drives Conference (IEMDC 2011) ; Niagara Falls, Ontario, Canada, 15 - 18 May 2011}, booktitle = {2011 IEEE International Electric Machines \& Drives Conference (IEMDC 2011) ; Niagara Falls, Ontario, Canada, 15 - 18 May 2011}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-4577-0060-6}, doi = {10.1109/IEMDC.2011.5994651}, pages = {515 -- 520}, abstract = {This paper presents a comprehensive computational fluid (CFD) model of a radial flux permanent magnet synchronous machine with interior magnets. In the CFD model the water jacket cooling and a simplified model of the topology of the distributed stator winding are considered. The heat sources of the CFD model are determined from a finite element analysis of the machine. The numerically determined temperature distributions of the machine are compared with measurement results from sensors located both in the stator and rotor. The particular focus of this paper is the analysis of the temperatures and the heat flow in the air gap and from the stator winding head and the rotor to the inner air.}, language = {en} } @inproceedings{KralHaumer, author = {Kral, Christian and Haumer, Anton}, title = {The New FundamentalWave Library for Modeling Rotating Electrical Three Phase Machines}, series = {Proceedings of the 8th International Modelica Conference; March 20th-22nd; Technical Univeristy; Dresden; Germany}, booktitle = {Proceedings of the 8th International Modelica Conference; March 20th-22nd; Technical Univeristy; Dresden; Germany}, publisher = {University Electronic Press}, address = {Link{\"o}ping}, isbn = {978-91-7393-096-3}, issn = {1650-3686}, doi = {10.3384/ecp11063170}, pages = {170 -- 179}, abstract = {This paper introduces the new FundemantalWave library which is included in the Modelica Standard Library 3.2. The presented Modelica package provides models and components of rotating electrical three phase machines. The presented electrical machine models are fully compatible with the original Machines library of the electrical domain but rely on the concept of the magnetic potential and magnetic flux fundamental waves. In this article; the connector concept; the components and electric machine models of the FundemantalWave package will be explained. Additionally; the didactic advantages and the flexibility of the proposed package in with respect to considering more enhanced and sophisticated effects will be discussed.}, language = {en} } @incollection{KralHaumer, author = {Kral, Christian and Haumer, Anton}, title = {Object Oriented Modeling of Rotating Electrical Machines}, series = {Advances in Computer Science and Engineering}, booktitle = {Advances in Computer Science and Engineering}, editor = {Schmidt, Matthias}, publisher = {IntechOpen}, isbn = {978-953-307-173-2}, doi = {10.5772/15898}, pages = {135 -- 160}, language = {en} } @article{KralKapellerGraggeretal., author = {Kral, Christian and Kapeller, Hansj{\"o}rg and Gragger, Johannes V. and Haumer, Anton and Kubicek, Bernhard}, title = {Phenomenon Rotor Fault-Multiple Electrical Rotor Asymmetries in Induction Machines}, series = {IEEE Transactions on Power Electronics}, volume = {25}, journal = {IEEE Transactions on Power Electronics}, number = {5}, publisher = {IEEE}, issn = {0885-8993}, doi = {10.1109/TPEL.2009.2037502}, pages = {1124 -- 1134}, abstract = {In the literature, the effects caused by a single or several adjacently broken rotor bars, or a broken end ring are thoroughly investigated. The phenomenon of various nonadjacently broken rotor bars has not been studied so far in detail. Since nonadjacently broken rotor bars may give rise to fault signatures, which are not directly related with the fault extent, it is important to understand the nature of multiple electrical rotor asymmetries in induction machines. The purpose of this paper is thus to investigate several combinations of electrical rotor asymmetries, to systematically elaborate the phenomena related to the broken bars and end rings. In this paper, a sophisticated simulation model and measurement results are used to analyze the phenomenon rotor fault.}, language = {en} } @incollection{KapellerHaumerKraletal., author = {Kapeller, Hansj{\"o}rg and Haumer, Anton and Kral, Christian and Grabner, Christian}, title = {Different Designs of Large Chipper Drives}, series = {Electronic Engineering and Computing Technology}, booktitle = {Electronic Engineering and Computing Technology}, editor = {Ao, Sio-Iong and Gelman, Len}, publisher = {Springer}, address = {Dordrecht}, isbn = {978-90-481-8775-1}, doi = {10.1007/978-90-481-8776-8_9}, pages = {93 -- 104}, abstract = {This paper presents two simulation models for two variants of a large chipper drive used in a paper mill. If a slip ring induction motor is used, the impact of a rotor circuit rheostat with respect to starting behavior and heavy duty load impulses can be examined. Furthermore a speed controlled squirrel cage induction machine will be investigated. The modeling language for both drives is Modelica. The simulation results for both drives are compared and discussed.}, language = {en} } @incollection{KralHaumerGrabner, author = {Kral, Christian and Haumer, Anton and Grabner, Christian}, title = {Determination of Consistent Induction Motor Parameters}, series = {Electronic Engineering and Computing Technology}, volume = {60}, booktitle = {Electronic Engineering and Computing Technology}, editor = {Ao, Sio-Iong and Gelman, Len}, publisher = {Springer}, address = {Dordrecht}, isbn = {978-90-481-8775-1}, doi = {10.1007/978-90-481-8776-8_7}, pages = {71 -- 80}, abstract = {From the rating plate data of an induction motor the nominal efficiency can be determined. Without detailed knowledge of equivalent circuit parameters, partial load behavior cannot be computed. Therefore, a combined calculation and estimation scheme is presented, where the consistent parameters of an equivalent circuit are elaborated, exactly matching the nominal operating point. From these parameters part load efficiencies can be determined.}, language = {en} } @incollection{KralHaumerGrabner, author = {Kral, Christian and Haumer, Anton and Grabner, Christian}, title = {Broken Rotor Bars in Squirrel Cage Induction Machines - Modeling and Simulation}, series = {Electronic Engineering and Computing Technology}, booktitle = {Electronic Engineering and Computing Technology}, editor = {Ao, Sio-Iong and Gelman, Len}, publisher = {Springer}, address = {Dordrecht}, isbn = {978-90-481-8775-1}, doi = {10.1007/978-90-481-8776-8_8}, pages = {81 -- 91}, abstract = {This paper presents a physical model of a squirrel cage induction machine with rotor topology. The machine is modeled in Modelica, an object oriented multi physical modeling system. The presented machine model is used to investigate electrical rotor asymmetries in induction machines. For the case of a single broken rotor bar a simulation model is compared with measurement results.}, language = {en} } @article{GraggerHaumerEinhorn, author = {Gragger, Johannes V. and Haumer, Anton and Einhorn, Markus}, title = {Averaged Model of a Buck Converter for Efficiency Analysis}, series = {Engineering Letters}, volume = {18}, journal = {Engineering Letters}, address = {Hong Kong}, abstract = {In this work a buck converter model for multidomain simulations is proposed and compared with a state-of-the-art buck converter model. In the proposed model no switching events are calculated. By avoiding the computation of the switching events in power electronic models the processing time of multidomain simulations can be decreased significantly. The proposed model calculates any operation point of the buck converter in continuous inductor current conduction mode (CICM) while considering the conduction losses and switching losses. It is possible to utilize the proposed modeling approach also for other dc-to-dc converter topologies. Laboratory test results for the validation of the proposed model are included.}, language = {en} } @article{KralHaumerGrabner, author = {Kral, Christian and Haumer, Anton and Grabner, Christian}, title = {Consistent Induction Motor Parameters for the Calculation of Partial Load Efficiencies by Means of an Advanced Simulation Model}, series = {Engineering Letters}, volume = {18}, journal = {Engineering Letters}, number = {1}, address = {Hong Kong}, issn = {1816-0948}, abstract = {From the rating plate data of an induction motor the nominal efficiency can be determined. Without detailed knowledge of equivalent circuit parameters, partial load behavior cannot be computed. Therefore, a combined calculation and estimation scheme is presented, where the consistent parameters of an equivalent circuit are elaborated, exactly matching the nominal operating point. From these parameters part load efficiencies can be determined.}, language = {en} } @incollection{GrabnerGraggerKapelleretal., author = {Grabner, Christian and Gragger, Johannes V. and Kapeller, Hansj{\"o}rg and Haumer, Anton and Kral, Christian}, title = {Sensorless PM-Drive Aspects}, series = {Electronic Engineering and Computing Technology}, booktitle = {Electronic Engineering and Computing Technology}, editor = {Ao, Sio-Iong and Gelman, Len}, publisher = {Springer}, address = {Dordrecht}, isbn = {978-90-481-8775-1}, doi = {10.1007/978-90-481-8776-8_3}, pages = {25 -- 35}, abstract = {The development procedure of permanent magnet drives for sensor less operation beginning from standstill under overload conditions has to consider different design aspects coevally. First, the robust rotor position sensing by test signal enforces a design with a strongly different behavior of the spatial dq-oriented differential inductance values. Therefore, the interior rotor magnet array arrangement is from principle predestinated for the controlled sensor less mode including standstill. Fortunately, in order to reduce costs, the distinct reluctance torque capability of such interior magnet arrangement is additionally used for a significantly increased torque by applying a pre-oriented stator current space vectors within the quasi-steady control.}, language = {en} } @article{KralHaumerHaigisetal., author = {Kral, Christian and Haumer, Anton and Haigis, Matthias and Lang, Hermann and Kapeller, Hansj{\"o}rg}, title = {Comparison of a CFD Analysis and a Thermal Equivalent Circuit Model of a TEFC Induction Machine With Measurements}, series = {IEEE Transactions on Energy Conversion}, volume = {24}, journal = {IEEE Transactions on Energy Conversion}, number = {4}, publisher = {IEEE}, issn = {0885-8969}, doi = {10.1109/TEC.2009.2025428}, pages = {809 -- 818}, abstract = {For a totally enclosed fan-cooled induction machine, two methods of numerical analysis are compared with measurements. The first numerical method is based on computational fluid dynamics (CFDs) and the second one uses a thermal equivalent circuit (TEC). For the analysis based on CFD, a 3-D induction machine including housing is modeled. The numeric solution of the flow equations is determined for stationary temperature distributions. For the TEC, a discretized one-and-a-half-dimensional model of the induction machine is considered. With the TEC model, stationary and transient operating conditions can be simulated. Measurement results are determined by iron-copper-nickel sensors embedded in the stator winding and the housing, as well as by an IR sensor for measuring the rotor temperature. With these measurement signals, stationary and transient operating conditions can be analyzed. For stationary operating conditions, additionally, the housing temperatures are determined by an IR camera. The investigated simulation and measurement methods reveal different local and global temperatures, and thus, only certain aspects and characteristics of the obtained temperatures can be compared. Nevertheless, certain conclusions can be drawn from comparing these aspects considering the actual restrictions of each of the applied methods.}, language = {en} } @inproceedings{EbnerHaumerSimicetal., author = {Ebner, Arno and Haumer, Anton and Simic, Dragan and Pirker, Franz}, title = {Interacting Modelica using a Named Pipe for Hardware-in-the-loop Simulation}, series = {Modelica 2006, Conference proceedings / 5th International Modelica Conference : September 4 - 5, 2006, Vienna, Austria}, booktitle = {Modelica 2006, Conference proceedings / 5th International Modelica Conference : September 4 - 5, 2006, Vienna, Austria}, pages = {261 -- 266}, abstract = {The paper presents a concept and an implementation of Modelica simulation interaction using the operating system inter-process communication method of the Named Pipe. The main aim of this presented work is to implement a hardware-in-the-loop simulation (HILS) environment based on Dymola which runs on a normal Microsoft Windows Personal Com-puter. An energy storage test bench is connected by an ana-logue and digital data input/output card with the Dymola simulation computer. With this proposed system, particularly long-time simulations with sample rates up to 30 Hz can be executed very cost effective. Typical applications are simulations of drive cycles to test energy storage systems in electrified vehicles such as batteries or fuel cells. Other application ex-amples are the verification of battery models, thermal management models or battery management sys-tem (BMS) models. In this paper all methods used for implementation are described in detail. Especially the concept of inter-process communication and the concept for real-time and simulation time synchronization is discused. An application example which uses the provided concept is also shown at in this paper. In this example a longitudinal simulation of a vehicle is pre-sented. The startup phase of the internal combusting engine model and a short drive cycle in combination with a connected real battery is shown.}, language = {en} }