@inproceedings{MiedlBraun, author = {Miedl, Christian and Braun, J{\"u}rgen}, title = {Powertrain and electric system design of a 800-volt all-electric car}, series = {European Conference on Nanoelectronics and Embedded Systems for Electric Mobility, eMotion in Smart Cities, 24.-28. September, 2012, Bologna, Italy}, booktitle = {European Conference on Nanoelectronics and Embedded Systems for Electric Mobility, eMotion in Smart Cities, 24.-28. September, 2012, Bologna, Italy}, language = {en} } @inproceedings{BeckeSchlegl, author = {Becke, Mark and Schlegl, Thomas}, title = {Least squares pose estimation of cylinder axes from multiple views using contour line features}, series = {IECON 2015 - 41st Annual Conference of the IEEE Industrial Electronics Society, 9-12 Nov. 2015, Yokohama, Japan}, booktitle = {IECON 2015 - 41st Annual Conference of the IEEE Industrial Electronics Society, 9-12 Nov. 2015, Yokohama, Japan}, publisher = {IEEE}, doi = {10.1109/IECON.2015.7392371}, pages = {1855 -- 1861}, abstract = {In this paper, a new method for a minimum-error pose estimation of cylinder axes based on apparent contour line features from multiple views is presented. Novel model equations for both single and particularly multiple views are derived, and based upon these, an iterative algorithm for least squares fitting the model to imaged cylinder contour line features is introduced. The good performance and fast convergence of the proposed algorithm is shown by solving exemplary fitting problems.}, language = {en} } @inproceedings{HofmannScharfenberg, author = {Hofmann, Gerhard and Scharfenberg, Georg}, title = {Applicability of the ISO 26262 for functional safety for motorbikes}, series = {2014 International Conference on Applied Electronics, 9-10 Sept. 2014, Pilsen, Czech Republic}, booktitle = {2014 International Conference on Applied Electronics, 9-10 Sept. 2014, Pilsen, Czech Republic}, publisher = {IEEE}, doi = {10.1109/AE.2014.7011679}, pages = {107 -- 112}, abstract = {This article deals with the question to what extent the automotive standard for functional safety ISO 26262 is also applicable to motorbikes. It examines thereby, on the one hand where to find comparable criteria between cars and motorbikes from the standpoint of functional safety, and, on the other hand, where differences between the automobile and the motorbike must be considered. It shows the extent to which the safety-related automotive standard is applicable to motorbikes. Furthermore, the differences are determined, which must lead to the consequence of a new "state of the art" and to a new standard for motorbikes. On the example of a light function the new MSIL classification gets applied. In this article, the motorbike is viewed as a whole. For the most parts the standard is also valid for scooters.}, language = {en} } @inproceedings{Schiek, author = {Schiek, Roland}, title = {Self-phase modulation in lithium niobate waveguides}, series = {2014 International Conference Laser Optics, title=Self-phase modulation in lithium niobate waveguides, 30 June-4 July 2014, St. Petersburg, Russia}, booktitle = {2014 International Conference Laser Optics, title=Self-phase modulation in lithium niobate waveguides, 30 June-4 July 2014, St. Petersburg, Russia}, publisher = {IEEE}, doi = {10.1109/LO.2014.6886403}, abstract = {Self-phase modulation in lithium niobate wave-guides with cascaded quadratic and cubic nonlinearities is characterized by comparison of amplitude and phase of input and output pulse envelopes and spectra. Cubic nonlinear susceptibility coefficients of lithium niobate were determined from the measured nonlinear phase shifts.}, language = {en} } @inproceedings{HofmeisterKrebsSchickhuberetal., author = {Hofmeister, Justus and Krebs, Stefan and Schickhuber, Gerald and Scharfenberg, Georg}, title = {Design and development of a Pico Hydro turbine system for the use in developing countries}, series = {2015 5th International Youth Conference on Energy (IYCE), 27-30 May 2015, Pisa, Italy}, booktitle = {2015 5th International Youth Conference on Energy (IYCE), 27-30 May 2015, Pisa, Italy}, publisher = {IEEE}, doi = {10.1109/IYCE.2015.7180767}, pages = {1 -- 7}, abstract = {In Sub-Saharan Africa less than 10\% of the rural population has access to electricity [1]. Stand-alone power systems (SPS) can be a solution to the problem of the lack of electricity, which highlights challenges such as modules installation costs as well as the sufficient knowledge required for installing, maintaining and operating such systems. With this fact in mind, a 250 W Low Head turbine system was developed and optimized to have the advantage of the simplicity of installation and a construction from readily available materials. This design scores the electrical efficiency of 60\%, reduces manufacturing unit coast to 130 € and takes into account the necessity of providing a clear and simple manual describing the manufacturing and installation. A better version of the load controller, using a microcomputer is under current development. Mounting of the system have been simplified to reduce the amount of construction material required to provide uninterrupted 230 V at 50 Hz AC or optional 12 V DC power supply. Current efforts aim on transferring the required mechanical and electrical knowledge for building, programming, installing and maintaining such system to schools in targeted countries. This project doesn't only provide people in rural developing countries a gleam of hope to catch up with the developed countries, but also helps students to use their theoretical knowledge to realize practical applications.}, language = {en} } @inproceedings{RoeselKoehler, author = {R{\"o}sel, Birgit and K{\"o}hler, Thomas}, title = {First results of a new digitalized concept for teaching control theory as minor subject at a university of applied science}, series = {2018 IEEE Global Engineering Education Conference (EDUCON), 17-20 April 2018, Santa Cruz de Tenerife, Spain}, booktitle = {2018 IEEE Global Engineering Education Conference (EDUCON), 17-20 April 2018, Santa Cruz de Tenerife, Spain}, publisher = {IEEE}, doi = {10.1109/EDUCON.2018.8363217}, pages = {118 -- 125}, abstract = {This paper presents a digitalized concept for teaching control theory as minor subject with an integrated approach for lectures, exercises and practical sessions and first results of the implementation at the department of electrical engineering at the OTH Regensburg. The concept uses activating methods like blended learning and possibilities of digitalization of teaching implementing Just in Time Teaching and Peer Instruction. The base of the new concept is the idea of constructive alignment. Furthermore this paper presents the feedback of the students along with an accompanying scientific research over several semesters. The data obtained from the presented module are compared with the data from other blended learning approaches in Germany.}, language = {en} } @inproceedings{HaumerKral, author = {Haumer, Anton and Kral, Christian}, title = {Enhancements of Electric Machine Models: The EMachines Library}, series = {Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015}, volume = {118}, booktitle = {Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015}, publisher = {Link{\"o}ping University Electronic Press}, doi = {10.3384/ecp15118509}, pages = {509 -- 515}, abstract = {Transient models of multi phase electric machines are already implemented in the Modelica Standard Library (MSL). However, advanced effects like saturation and skin effect are not taken into account. As an extension to the MSL models, the new EMachines library is presented. This package will be released as a supplemental library to the commercial EDrives library. The particular focus of this paper is on the deep bar effect of induction machines. A comparison of simulation results demonstrates the influence of the skin effect on the operational behavior of the machines. At the end of this publication further developments of the EMachines library will be outlined.}, language = {en} } @inproceedings{SchmidtFuchsFuchs, author = {Schmidt, Hans-Peter and Fuchs, Andreas and Fuchs, Stefan}, title = {Simultaneous contact less charging of multiple electric vehicles: Contact less power and data transfer for multiple distributed loads}, series = {2014 4th International Electric Drives Production Conference ( 30 Sept.-1 Oct. 2014, Nuremberg, Germany}, booktitle = {2014 4th International Electric Drives Production Conference ( 30 Sept.-1 Oct. 2014, Nuremberg, Germany}, publisher = {IEEE}, doi = {10.1109/EDPC.2014.6984435}, pages = {1 -- 3}, abstract = {A design of a 3-phase inductive power and data transfer for multiple stationary loads is proposed. It focuses on stable load voltages while minimizing electromagnetic interference. Loads are contactless charging units of electric vehicles at car parks. Physical properties of the inductive couplers are modelled via 3-D FEM and lumped parameters are used for system studies. Design principles are verified at laboratory scale with a purpose built test stand.}, language = {en} } @inproceedings{GrothmannPoelsterlGerling, author = {Grothmann, Benjamin and Poelsterl, Thomas and Gerling, Dieter}, title = {Online compensation of current sensor gain-faults for safety-relevant IPM-drives}, series = {2017 IEEE Transportation Electrification Conference and Expo (ITEC), 22-24 June 2017, Chicago, IL, USA}, booktitle = {2017 IEEE Transportation Electrification Conference and Expo (ITEC), 22-24 June 2017, Chicago, IL, USA}, publisher = {IEEE}, doi = {10.1109/ITEC.2017.7993355}, pages = {701 -- 706}, abstract = {Detection and compensation of current sensor gain-faults regardless of the operating-point is a crucial aspect for safety-relevant servo-drives. This paper presents and investigates a new direct phase-gain re-balancing methodology, especially suited for interior permanent magnet machine (IPM) drives mostly operating at low speed-ranges including standstill. The proposed model-based approach utilizes high-frequency signal-injection (HFI) to facilitate fast and persistent sensor monitoring for any operating state of the drive. No additional sensing hardware is required. Extraction of the HFI-phase-current response enables detection and immediate compensation of sensor gain-faults. Implementation aspects of the proposed concept are discussed thoroughly. Experimental results are presented to prove and investigate robustness, reliability and fault-tolerant performance.}, language = {en} } @inproceedings{HacklHirschbergLexetal., author = {Hackl, Andreas and Hirschberg, Wolfgang and Lex, Cornelia and Rill, Georg}, title = {Parameterization Process of the Maxwell Model to Describe the Transient Force Behavior of a Tire}, series = {WCX 17: SAE World Congress Experience 2017}, booktitle = {WCX 17: SAE World Congress Experience 2017}, publisher = {SAE}, doi = {10.4271/2017-01-1505}, abstract = {The present technical article deals with the modeling of dynamic tire forces, which are relevant during interactions of safety relevant Advanced Driver Assistance Systems (ADAS). Special attention has been paid on simple but effective tire modeling of semi-physical type. In previous investigations, experimental validation showed that the well-known first-order Kelvin-Voigt model, described by a spring and damper element, describes good suitability around fixed operation points, but is limited for a wide working range. When aiming to run vehicle dynamics models within a frequency band of excitation up to 8 Hz, these models deliver remarkable deviations from measured tire characteristics. To overcome this limitation, a nonlinear Maxwell spring-damper element was introduced which is qualified to model the dynamic hardening of the elastomer materials of the tire. However, the advantage of a more realistic description of the transient behavior leads to a more complex parametrization process. Therefore, in the proposed article attention is paid to describe the identification process including defined maneuvers to parameterize the tire model, where the accuracy of the parameter strongly depends on the quality of the available input data from measurement. In order to study this important aspect of parameterization, the reference data from simulation of the full physical tire model FTire is applied like a "virtual measurement" of specified testing maneuvers. The procedure of simulation by means of the enhanced first order dynamics model is implemented by the semi-physical tire model TMeasy. Finally, the improvements of the extended model are discussed and an outlook for future work is given.}, language = {en} } @inproceedings{GrimmHaumer, author = {Grimm, Alexander and Haumer, Anton}, title = {EMOTH The EMobility Library of OTH Regensburg}, series = {Proceedings of the 12th International Modelica Conference, Prague, Czech Republic, May 15-17, 2017}, booktitle = {Proceedings of the 12th International Modelica Conference, Prague, Czech Republic, May 15-17, 2017}, publisher = {Link{\"o}ping University Electronic Press}, doi = {10.3384/ecp17132285}, pages = {285 -- 290}, abstract = {The importance of E-Mobility is rapidly increasing, not only for private vehicle traffic but also for public transport. In and around Regensburg, Germany there are a lot of automotive companies. Therefore E-Mobility is an important topic in the curriculum of several courses of study at the East-Bavarian Technical University of Applied Sciences Regensburg (OTH). One Master of Applied Research student at OTH has chosen the topic to develop an open-source simulation tool for electric vehicles - the EMOTH Library - based on Modelica and to refine several aspects of the library during the one and a half year of the master course. After one semester, the basic version of the library is available and will be presented in this paper.}, language = {en} } @inproceedings{HacklHirschbergLexetal., author = {Hackl, Andreas and Hirschberg, W. and Lex, C. and Rill, Georg}, title = {Experimental validation of the Maxwell model for description of transient tyre forces}, series = {16. Internationales Stuttgarter Symposium, Automobil- und Motorentechnik}, booktitle = {16. Internationales Stuttgarter Symposium, Automobil- und Motorentechnik}, editor = {Bargende, Michael and Reuss, Hans-Christian and Wiedemann, Jochen}, publisher = {Springer}, address = {Wiesbaden}, isbn = {978-3-658-13254-5}, doi = {10.1007/978-3-658-13255-2_29}, pages = {401 -- 418}, abstract = {Modelling and simulation of safety relevant Driver Assistance Systems (DAS) and Vehicle Dynamics Controllers (VDC) which act in standard and limit situations lead to increasing accuracy demands in the description of dynamic reactions of tyre contact forces, e.g. For that purpose, first-order approaches are widely applied in this field of vehicle dynamics and handling, which originate from Schlippe \& Dietrich, were modified by Pacejka and later on refined by Rill.}, language = {en} } @inproceedings{MuehlbauerRablRottengruber, author = {M{\"u}hlbauer, Christian and Rabl, Hans-Peter and Rottengruber, Hermann}, title = {Akustische Analyse und Optimierung von mechatronischen Kraftstoffeinspritzsystemen}, series = {Tagungsband DAGA 2019 - 45. Jahrestagung f{\"u}r Akustik, 18.-21. M{\"a}rz 2019, Rostock}, booktitle = {Tagungsband DAGA 2019 - 45. Jahrestagung f{\"u}r Akustik, 18.-21. M{\"a}rz 2019, Rostock}, publisher = {Deutsche Gesellschaft f{\"u}r Akustik}, address = {Berlin}, isbn = {978-3-939296-14-0}, pages = {647 -- 650}, language = {de} } @misc{SchwanzerDietrichGadereretal., author = {Schwanzer, Peter and Dietrich, Markus and Gaderer, Matthias and Rabl, Hans-Peter}, title = {Detektion unterschiedlicher Medien in Gasoline Particulate Filter (GPF) mit Hilfe eines Radio-Frequenz (RF-) Sensors}, series = {Bayerische Wissenschaftsforum - BayWISS 2020}, journal = {Bayerische Wissenschaftsforum - BayWISS 2020}, language = {de} } @book{AltmannGebhardEmbergeretal., author = {Altmann, Robert and Gebhard, J{\"u}rgen and Emberger, Peter and Thuneke, Klaus and Rabl, Hans-Peter and Remmele, Edgar}, title = {Z{\"u}nd- und Brennverhalten von Pflanzen{\"o}lkraftstoff und {\"U}bertragung auf einen Motor der Abgasstufe V}, volume = {69}, publisher = {Technologie- und F{\"o}rderzentrum im Kompetenzzentrum f{\"u}r Nachwachsende Rohstoffe}, address = {Straubing}, issn = {1614-1008}, pages = {188}, abstract = {Durch den Ersatz von Dieselkraftstoff durch Raps{\"o}lkraftstoff (R100) k{\"o}nnen Treibhausgasemissionen reduziert werden. F{\"u}r einen st{\"o}rungsfreien Betrieb eines Motors mit Raps{\"o}lkraftstoff sind jedoch Modifikationen an Motorkomponenten und Motorsteuerger{\"a}t notwendig, um eine effiziente Verbrennung im Motor zu erreichen. Ziel des Vorhabens ist die Erarbeitung von Grundlagen zur Auslegung der Motorsteuerung pflanzen{\"o}ltauglicher Offroad-Motoren mit moderner Abgasnachbehandlung mit anschließender entsprechender Abstimmung der Motorapplikation am Pr{\"u}fstand. Grundlegende Untersuchungen der physikalischen Prozessabl{\"a}ufe von R100 bei der Einspritzung werden an einem hydraulischen Druckanstiegsanalysator (HDA) und einer Hochdruck-Hochtemperatur-Kammer (HDHT-Kammer) durchgef{\"u}hrt. Unterschiede im Z{\"u}nd- und Brennverhalten werden in einer Konstantvolumenbrennkammer untersucht. Abschließend werden die Erkenntnisse am Motorenpr{\"u}fstand auf einen DEUTZ-Motor {\"u}bertragen, dessen Einspritzsystem auch bei den grundlegenden Untersuchungen verwendet wurde. Die Ergebnisse zeigen, dass das Einspritzverhalten von R100 eine h{\"o}here Sensitivit{\"a}t gegen{\"u}ber Kraftstofftemperaturvariationen aufweist als Dieselkraftstoff. Bei niedrigen raftstofftemperaturen sind mit R100 ein l{\"a}ngerer {\"O}ffnungsverzug und eine geringere Einspritzmenge festzustellen. Um diesen Einfluss bei der Einspritzstrategie zu kompensieren, ist die Kenntnis der Kraftstofftemperatur im Injektor notwendig. Eine weitere Herausforderung stellt die Gemischaufbereitung dar, hier f{\"u}hren unter anderem die h{\"o}here Viskosit{\"a}t und h{\"o}here Siedetemperaturen von R100 zu einem schm{\"a}leren Spritzwinkel und verz{\"o}gerter Verdampfung im Vergleich zum Dieselkraftstoff. Eine Erh{\"o}hung des Einspritzdrucks und h{\"o}here Temperaturen und Dr{\"u}cke in der Brennkammer verbessern die Gemischaufbereitung. Bei Bedingungen von mittlerer und hoher Last ist der Z{\"u}ndverzug von R100 k{\"u}rzer und das Verbrennungsverhalten {\"a}hnlich zum Dieselkraftstoff. Eine geringere W{\"a}rmefreisetzung von R100 wird durch den geringeren Heizwert verursacht. Unter Bedingungen von niedriger Last und Motorstart ist ein l{\"a}ngerer Z{\"u}ndverzug von R100 im Vergleich zum Dieselkraftstoff festzustellen. Eine Steigerung des Einspritzdrucks und h{\"o}here Brennkammerdr{\"u}cke und -temperaturen f{\"u}hren bei beiden Kraftstoffen zu k{\"u}rzeren Z{\"u}ndverz{\"u}gen, der Einfluss dieser Parameter ist jedoch f{\"u}r R100 st{\"a}rker als f{\"u}r Dieselkraftstoff. Voreinspritzungen f{\"u}hren bei beiden Kraftstoffen zu einer Verk{\"u}rzung des Z{\"u}ndverzugs der Haupteinspritzung und zu einer geringeren W{\"a}rmefreisetzungsrate. Am Motorpr{\"u}fstand ist bei gleicher Motorapplikation mit R100 eine geringere Leistung als mit Dieselkraftstoff festzustellen. Nach Angleichung der Motorleistung durch Anhebung der Einspritzmenge von R100 sind im Rohabgas Stickstoffoxid (NOX)- und Kohlenstoffmonoxidemissionen auf gleichem Niveau zu Dieselkraftstoff zu beobachten sowie geringere Partikelemissionen. Unter Verwendung eines DoE Vorgehens kann der Partikel-NOX - trade-off von R100 optimiert und Einstellparameter gefunden werden, in denen sowohl niedrigere NOX als auch niedrigere Partikelemissionen im Vergleich zum Dieselkraftstoff resultieren. Das installierte Abgasnachbehandlungssystem, bestehend aus einem Dieseloxidationskatalysator (DOC), Dieselpartikelfilter (DPF) und selektivem katalytischem Reduktionssystem (SCR), arbeitet f{\"u}r beide Kraftstoffe {\"a}hnlich und es scheint keine Anpassung der Dosierungsstrategie der w{\"a}ssrigen Harnstoffl{\"o}sung notwendig zu sein. Eine Regeneration des Partikelfilters mit R100 war nach Optimierung der Einstellparameter der Drosselklappe m{\"o}glich. Motorkaltstart und Leerlauf sind herausfordernde Betriebsphasen, die f{\"u}r R100 einer weiteren Optimierung bed{\"u}rfen. Eine Temperierung von R100 im Injektor auf 50-60 °C sowie eine Kompensation der Einspritzmenge in Abh{\"a}ngigkeit von der Kraftstofftemperatur sind m{\"o}gliche Verbesserungsmaßnahmen. Zudem kann durch einen fr{\"u}heren Einspritzbeginn von R100 das Verbrennungsverhalten angepasst werden. Die Motorpr{\"u}fstandsuntersuchungen best{\"a}tigen qualitativ die Erkenntnisse die mit dem hydraulischen Druckanstiegsanalysator (HDA), der Hochdruck-Hochtemperatur-Kammer (HDHT-Kammer) und der Konstantvolumenbrennkammer gewonnen wurden. Weitere Untersuchungen sind notwendig, um die Ergebnisse auf einen baugleichen, in einer mobilen Arbeitsmaschine eingebauten Motor zu transferieren, damit Informationen zur Dauerhaltbarkeit unter realen Bedingungen erhalten werden k{\"o}nnen. Weiterf{\"u}hrende Forschungsarbeiten sind im Bereich der Betriebsphasen des Motorkaltstarts und Leerlaufs mit Raps{\"o}lkraftstoff n{\"o}tig, um einen dauerhaft st{\"o}rungsfreien Betrieb in diesen Betriebsphasen zu erreichen. Die erzielten Erkenntnisse deuten darauf hin, dass hier noch viel Verbesserungspotenzial vorhanden ist.}, subject = {Biokraftstoff}, language = {de} } @inproceedings{SchneiderHotsLuftetal., author = {Schneider, Sebastian and Hots, Jan and Luft, Tommy and Rottengruber, Hermann and Verhey, Jesko L. and Rabl, Hans-Peter}, title = {Entwicklung einer empirischen Formel zur Bewertung der Tickerger{\"a}uschanteile von Motorger{\"a}uschen}, series = {DAGA 2019 - 45. Jahrestagung f{\"u}r Akustik, 8.-21. M{\"a}rz 2019, Rostock}, volume = {45}, booktitle = {DAGA 2019 - 45. Jahrestagung f{\"u}r Akustik, 8.-21. M{\"a}rz 2019, Rostock}, publisher = {Deutsche Gesellschaft f{\"u}r Akustik e.V.}, isbn = {978-3-939296-14-0}, pages = {643 -- 646}, language = {de} } @inproceedings{RiegerMuehlbauerWeberetal., author = {Rieger, Anna and M{\"u}hlbauer, Christian and Weber, Rainer and Rabl, Hans-Peter}, title = {Measures to Address the Dissonance Perception of Multiple Tonal Components in Sounds}, series = {DAGA 2019 - 45. Jahrestagung f{\"u}r Akustik, 18.-21. M{\"a}rz 2019, Rostock}, volume = {45}, booktitle = {DAGA 2019 - 45. Jahrestagung f{\"u}r Akustik, 18.-21. M{\"a}rz 2019, Rostock}, publisher = {Deutsche Gesellschaft f{\"u}r Akustik e.V.}, pages = {375 -- 378}, language = {en} } @misc{SchwanzerDietrichGadereretal., author = {Schwanzer, Peter and Dietrich, Markus and Gaderer, Matthias and Rabl, Hans-Peter}, title = {Monitoring von Partikelfiltern f{\"u}r den Einsatz in Fahrzeugen mit direkt- einspritzenden Ottomotoren mit einer Radio-Frequenz (RF-) Antenne}, series = {Kolloquium des Bayerischen Wissenschaftsforum}, journal = {Kolloquium des Bayerischen Wissenschaftsforum}, language = {de} } @misc{SchwanzerDietrichHaftetal., author = {Schwanzer, Peter and Dietrich, Markus and Haft, Gerhard and Gaderer, Matthias and Rabl, Hans-Peter}, title = {Oxidation Kinetics Determination of GDI Engine Soot by a Radio-Frequency Sensor}, series = {23rd Conference on Combustion Generated Nanoparticles 2019, June 17-20, Z{\"u}rich, Switzerland}, journal = {23rd Conference on Combustion Generated Nanoparticles 2019, June 17-20, Z{\"u}rich, Switzerland}, language = {en} } @inproceedings{Becke, author = {Becke, Mark}, title = {On Modeling and Least Squares Fitting of Cylinders from Single and Multiple Views Using Contour Line Features}, series = {Intelligent Robotics and Applications}, volume = {9246}, booktitle = {Intelligent Robotics and Applications}, editor = {Liu, Honghai and Kubota, Naoyuki and Zhu, Xiangyang and Dillmann, R{\"u}diger}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-22872-3}, doi = {10.1007/978-3-319-22873-0_33}, pages = {372 -- 385}, abstract = {In this paper, a new method for a minimum-error pose estimation of cylinder axes based on apparent contour line features from multiple views is presented. Novel model equations for both single and particularly multiple views are derived, and based upon these, an algorithm for least squares fitting the model to imaged cylinder contour line features is introduced. The good performance of the proposed algorithm is shown by solving an exemplary fitting problem.}, language = {en} } @inproceedings{HacklHirschbergLexetal., author = {Hackl, Andreas and Hirschberg, Wolfgang and Lex, Cornelia and Rill, Georg}, title = {Tyre Dynamics: Model Validation and Parameter Identification}, series = {Proceedings of the European Automotive Congress EAEC-ESFA 2015}, volume = {45}, booktitle = {Proceedings of the European Automotive Congress EAEC-ESFA 2015}, editor = {Andreescu, Cristian and Clenci, Adrian}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-27275-7}, doi = {10.1007/978-3-319-27276-4_20}, pages = {219 -- 232}, abstract = {The present paper deals with the experimental validation of tyre dynamics approaches as it is widely applied in tyre models for vehicle dynamics and handling. Firstly it gives a brief derivation of two modelling principles regarding the deflection velocity in the considered direction of the tyre's deformation. This is than followed by a brief description of the performed measurement procedure. From the measurements, a set of model parameters of the considered tyre, depending on different manoeuvre speeds and frequencies, is identified, where no particular fitting parameters for the tyre dynamics are needed. Based on these model parameters, the related dynamic simulations are carried out. The comparisons show that the applied first-order model describes the behaviour quite well within a certain operation range, whereas the second-order approach cannot deliver better results in spite of the longer computational time. However, for investigations within an enlarged frequency range of the steer input and at high slip angles, a more detailed model is recommended.}, language = {en} } @inproceedings{DiamantidisLenziSykora, author = {Diamantidis, Dimitris and Lenzi, Daniele and S{\´y}kora, Miroslav}, title = {Optimal decisions based on monitoring - case study of steel roof}, series = {Proceedings of the Joint COST TU1402-TU1406 - IABSE WC1 Workshop, Zagreb 2-3 March 2017}, booktitle = {Proceedings of the Joint COST TU1402-TU1406 - IABSE WC1 Workshop, Zagreb 2-3 March 2017}, doi = {10.5592/CO/BSHM2017.4.7}, pages = {4.7-1 -- 4.7-7}, abstract = {Monitoring of structures and related decisions based on cost optimization are discussed in this contribution. Many research publications and experimental data are currently available on inspection and on monitoring and they represent the outcome of the remarkable work done. Not all the topics of interest are widely debated and implemented in standards. The current state-of-practice in standards is summarized and aspects to be included in future recommendations are proposed. The implementation of risk-based decisions is illustrated in a case study dealing with a stadium roof in Northern Italy. Snow actions are important especially in northern and mountainous regions where heavy snowfalls and related accumulation result to considerable loads. As the roof structure fails to comply with the requirements of Eurocodes, a permanent monitoring system has been installed to allow for real time evaluation of the reliability level of the structure. The system supplies the necessary information supporting immediate decisions on closure of the stadium in case of an extraordinary snow load. Cost-optimal decisions regarding the closure of the stadium are analysed based on a limit state function, on probabilistic models for the influencing parameters including measurement uncertainty, economic losses related to closure and failure consequences. The results demonstrate the potential of the use of the monitoring systems and probabilistic reliability analysis in order to support decisions and highlight the need for their implementation in future standards.}, language = {en} } @inproceedings{Neidhart, author = {Neidhart, Thomas}, title = {Bodenphysikalische und bodenmechanische Anforderungen an ZFSV (Fl{\"u}ssigboden) als Bettungsmaterialien erdverlegter Hochspannungsleitungen}, series = {Rohrleitungen in digitalen Arbeitswelten : Tagungsband zum 31. Oldenburger Rohrleitungsforum 2017}, booktitle = {Rohrleitungen in digitalen Arbeitswelten : Tagungsband zum 31. Oldenburger Rohrleitungsforum 2017}, editor = {Wegener, Thomas}, publisher = {Vulkan Verlag}, address = {Essen}, isbn = {978-3-8027-2865-5}, pages = {337}, language = {de} } @article{UhlarHeyderKoenig, author = {Uhlar, Stefan and Heyder, Florian and Koenig, Thomas}, title = {Assessment of two physical tyre models in relation to their NVH performance up to 300 Hz}, series = {Vehicle system dynamics}, volume = {59}, journal = {Vehicle system dynamics}, number = {3}, publisher = {Taylor\&Francis}, doi = {10.1080/00423114.2019.1681475}, pages = {331 -- 351}, abstract = {The prediction of structure-borne noise using numerical methods has a crucial influence during the development process of modern passenger cars. In order to minimise the dynamic forces from the chassis transferred to the body structure, multibody simulation (MBS) can be used. The link between the road surface and the chassis is established by the tyre and its own structural dynamic characteristics. Therefore, it is substantial and the main goal of the present paper to investigate the Noise, Vibration and Harshness (NVH) performance of two commercial physical tyre models available and commonly used in the market. The intention is to point out what kind of results (up-to-date) a user of these structural dynamic tyre models, namely FTire and CDtire/3D, will get with a focus on NVH. The authors strictly follow the established process of how to obtain the fitted tyre property files, as any other user of FTire and CDTire currently does. This process includes a measurement campaign of the real tyre and a subsequent fitting of the tyre property file. The fitting in this case is provided by the tyre model developers themselves, namely cosin and Fraunhofer ITWM. The tyre models are then integrated into the MBS software MSC.Adams where their performance will be assessed based on measured wheel-hub forces in the time and frequency domain up to 300 Hz.}, language = {en} } @misc{OetjenRiegerRabletal., author = {Oetjen, Arne and Rieger, Anna and Rabl, Hans-Peter and van de Par, Steven}, title = {The role of dissonance in the sound quality perception for electric vehicles}, series = {The Journal of the Acoustical Society of America}, volume = {148}, journal = {The Journal of the Acoustical Society of America}, number = {4}, publisher = {Acoustical Society of America}, doi = {10.1121/1.5147356}, abstract = {Tonal components can be regarded as one of the most relevant components for interior sound quality of electric vehicles, especially at low speeds. Sources for these tones are for example the vehicles' drivetrains but also other technical components. Depending on the driving conditions, due to the interaction of various dominant sources, audible tone complexes can occur. Similar to musical intervals, the different frequency ratios within these complexes can result in consonant or dissonant sensations. The strength of this sensation does not only depend on the frequency relation of the tones but also on their relative levels. In this study, different musical intervals were subjectively rated in terms of their specific consonant or dissonant character. Using an adaptive procedure, sound pairs, each consisting of a two-tone signal, where adjusted to equal dissonance by varying the level of the second tone of one of the two-tone signals. Using the same paradigm, also pairs of equal vehicle sound quality were obtained. With these results, it is possible to quantify dissonance, and theinfluence of dissonance on sound quality expressed in terms of level differences of two-tone signals. These results can help to make the concept of dissonance more useful for sound-engineering applications.}, language = {en} } @article{SindersbergerPremMonkman, author = {Sindersberger, Dirk and Prem, Nina and Monkman, Gareth J.}, title = {Self-assembling structure formation in low-density magnetoactive polymers}, series = {Journal of Applied Polymer Science}, volume = {137}, journal = {Journal of Applied Polymer Science}, number = {3}, publisher = {Wiley}, doi = {10.1002/app.48291}, abstract = {The formation of microstructures in magnetoactive polymers (MAPs) is a recently discovered phenomenon found only with very low filler particle concentrations (less than 3 wt \%). Due to the degassing process, filler particles collect around an ascending bubble, which dissolves at a certain point leaving particulate rings within the matrix. The formation of toroidal microstructures commences as filler concentration approaches 1 wt \%. The development of coherent parallel aligned rings with a compact order continues as particle concentrations increase toward 2 wt \%. Between 2 and 3 wt \% capillary doublets develop, while mass percentages higher than 3\% result in increasing entropy as the random order of particle agglomeration found in higher concentration MAP dominates. Self-structured samples of different filler material and concentrations between 1 and 3 wt \% have been investigated using X-ray tomography, where the emerging structures can be observed and visualized. The ring structures resulting from this research represent microinductivities which can be fabricated in a targeted manner, thus enabling new applications in the high-frequency radio field. Furthermore, these anisotropic, but well-organized, structures have magnetic field-dependent implications for optical, thermal, acoustic, and medical applications.}, language = {en} } @inproceedings{ReindlMeierNiemetz, author = {Reindl, Andrea and Meier, Hans and Niemetz, Michael}, title = {Software Framework for the Simulation of a Decentralized Battery Management System Consisting of Intelligent Battery Cells}, series = {2019 IEEE Student Conference on Research and Development (SCOReD), 15-17 Oct. 2019, Bandar Seri Iskandar, Malaysia}, booktitle = {2019 IEEE Student Conference on Research and Development (SCOReD), 15-17 Oct. 2019, Bandar Seri Iskandar, Malaysia}, doi = {10.1109/SCORED.2019.8896284}, pages = {75 -- 80}, abstract = {Conventional battery management systems typically adopt hierarchical master-slave architectures. With regard to an uninterruptible power supply, the most significant disadvantage of central structures is the dependency of the errorfree function of the superior master board. The decentralized battery management system presented in this paper, consisting of consumers, generators and intelligent battery cells, is controlled without any central coordination authority. For this purpose, an intelligent control algorithm and a leader election algorithm are implemented on the microcontrollers of the battery cells. To test different control and election strategies, a software framework is presented for the complete simulation of the decentralized battery management system consisting of equal participants.}, language = {en} } @inproceedings{HopkinsHopfenspergerMellor, author = {Hopkins, Andrew and Hopfensperger, Bernhard and Mellor, Phil}, title = {DC-link Capacitor Reduction in Low Voltage and High Power Integrated Modular Motor Drives}, series = {2019 IEEE Energy Conversion Congress and Exposition (ECCE), 29 Sept.-3 Oct. 2019, Baltimore, MD, USA}, booktitle = {2019 IEEE Energy Conversion Congress and Exposition (ECCE), 29 Sept.-3 Oct. 2019, Baltimore, MD, USA}, doi = {10.1109/ECCE.2019.8913213}, pages = {3208 -- 3214}, abstract = {The development of 48V high power (>15 kW) automotive propulsion drives demands close integration of the power electronics and the electrical machine. Due to the large operating currents distributed multi-phase topologies are needed and physically separating the power converter from the e-machine would involve heavy cabling and costly connections. The volume and cost of the filter capacitor represents a major challenge in closely integrated high power integrated modular motor drives and techniques are needed to minimize this. The DC-link capacitor requires a large ripple current handling capability and cost, size and reliability limitations result in suitable candidate technologies being those with low volumetric energy densities. Use of interleaved multi three-phase machines are attractive due to the associated capacitor ripple current reduction. Discontinuous modulation schemes may also be employed as a technique for reducing the current ripple. In this paper techniques for capacitor ripple reduction are assessed through simulation and compared.}, language = {en} } @inproceedings{ScharfenbergElisHofmann, author = {Scharfenberg, Georg and Elis, Ludek and Hofmann, Gerhard}, title = {New Design Methodology - Using VHDL-AMS Models to Consider Aging Effects in Automotive Mechatronic Circuits for Safety Relevant Functions}, series = {2019 International Conference on Applied Electronics (AE), 10-11 Sept. 2019, Pilsen, Czech Republic}, booktitle = {2019 International Conference on Applied Electronics (AE), 10-11 Sept. 2019, Pilsen, Czech Republic}, doi = {10.23919/AE.2019.8867034}, pages = {1 -- 5}, abstract = {In this paper a design method for mechatronic functions in an early design phase under consideration of the requirements of functional safety is proposed [14]. The goal of the method is to discover threats for the safety goals and to prove or optimize the diagnostic mechanisms. At the current design process a lifetime endurance test is performed in a late project phase. In order to avoid unexpected late design changes the method should be applied in an early design phase. The method is an additional way to avoid design failures for E/E functions with special focus on aging in the field of functional safety applications. The method is developed out of three standards VDI 2221 methodology for development and construction of technical systems and products [1]), VDI 2206 design methodology for mechatronic systems [2] and the ISO 26262 road vehicles - Functional Safety [3] by using the V-Model. Furthermore, a core element of the design method is simulating aging effects by applying VHDL - AMS. To demonstrate the design methodology a sensor out of the EGAS function is chosen as a safety relevant automotive system. The limitation is the availability of aging data for electrical components.}, language = {en} } @inproceedings{BrkicCeranElmoghazyetal., author = {Brkic, Jovan and Ceran, Muaz and Elmoghazy, Mohamed and Kavlak, Ramazan and Haumer, Anton and Kral, Christian}, title = {Open Source PhotoVoltaics Library for Systemic Investigations}, series = {Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany}, booktitle = {Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany}, publisher = {Link{\"o}ing University Electronic Press}, doi = {10.3384/ecp1915741}, pages = {41 -- 50}, abstract = {For the planning of photovoltaic power plants standard software tools are used. Most of these software tools use statistical solar data to determine the overall energy harvest of a photovoltaic plant over one year. The calculations rely on stationary location and ideal boundary conditions, e.g., constant ambient temperature. Even though, for example, shadowing may be considered by standard software, the investigation of untypical configurations and problems cannot be performed by such software, as most configurations cannot be changed by the user. The presented PhotoVoltaics library was developed with the intention to provide a flexible framework for standard and non-standard problems. Particularly, the PhotoVoltaics library can be coupled with other Modelica libraries to perform systemic investigations. An application library, PhotoVoltaics_TGM, is provided as add-on, where measured data of two photovoltaic pants of the TGM in Vienna can be compared with simulation results. This add-on library serves as validation of the PhotoVoltaics library.}, language = {en} } @inproceedings{AlexanderHaumer, author = {Alexander, Grimm and Haumer, Anton}, title = {Parametrization Of A Simplified Physical Battery Model}, series = {Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany}, booktitle = {Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany}, publisher = {Link{\"o}ing University Electronic Press}, doi = {10.3384/ecp19157215}, pages = {215 -- 220}, abstract = {The importance of batteries is increasing, especially in the field of the high power requirement systems like electric driven vehicles. Mobile energy storage makes it possible to accelerate with incredible torque, without any accruing air pollution. Due to the high costs of real components, it is of great use to simulate battery driven systems before building them. Transient processes within a cell are highly dependent on the operating point of the complete system, which makes it difficult to create equations and model arameterizations. This paper shows which data is important for cell modeling and how to parameterize simplified physical cell models.}, language = {en} } @article{SelmairMaurerLaietal., author = {Selmair, Maximilian and Maurer, Tobias and Lai, Chun-Han and Grant, David}, title = {Enhancing the efficiency of charging \& parking processes for Autonomous Mobile Robot fleets}, series = {Journal of Power Sources}, volume = {521}, journal = {Journal of Power Sources}, number = {3}, publisher = {Elsevier}, doi = {10.1016/j.jpowsour.2021.230894}, abstract = {The allocation of tasks to Autonomous Mobile Robots in a production setting in combination with the most efficient parking and charging processes are the focus of this paper. This study presents a simulative evaluation of the theoretical allocation methods developed in Selmair and Maurer (2020) combined with either hard or dynamic availability rules to ascertain the most efficient parameters of an Autonomous Mobile Robot System. In order to quantify this efficiency, the following Key Performance Indicator (KPI) were considered: number of delayed orders, driven fleet metres and the percentage of available Autonomous Mobile Robot as determined by their state of charge. Additionally, as an alternative energy source, a fast-charging battery developed by Battery Streak Inc. was included in this study. The results show that, in comparison to a conventional and commonly used trivial strategy, our developed strategies provide superior results in terms of the relevant KPI.}, language = {en} } @article{SykoraHolickyJungetal., author = {S{\´y}kora, Miroslav and Holicky, Milan and Jung, Karel and Diamantidis, Dimitris}, title = {Human safety criteria for risk-based structural design}, series = {International Journal of Safety and Security Engineering}, volume = {8}, journal = {International Journal of Safety and Security Engineering}, number = {2}, publisher = {WIT Press}, doi = {10.2495/SAFE-V8-N2-287-298}, pages = {287 -- 298}, abstract = {Risk and reliability criteria are well established in many industrial sectors such as the offshore, chemi- cal or nuclear industries. Comparative risk thresholds have been specified to allow a responsible organization or regulator to identify activities, which impose an acceptable level of risk concerning the participating individuals, or society as a whole. The scope of this contribution is to present target reliability criteria based on acceptable human safety levels. Application of theoretical principles is illustrated by examples of railway engineering structures. Initially it is shown how civil engineering structures for which human safety criteria play a role are classified according to Eurocodes. Examples include bridges, tunnels or station buildings. The general concepts for risk acceptance are then briefly reviewed, particularly in their relation to the target reliability criteria. The distinction between the two types of criteria is made: group risk and the acceptance criterion based on the Life Quality Index LQI approach introduced by ISO 2394:2015. The differences between the criteria for new and existing structures are discussed. The application is illustrated by an example of a bridge crossing an important railway line. It appears that while benefits and costs of a private stakeholder or public authority are reflected by economic optimisation, the society should define the limits for human safety to achieve uniform risks for various daily-life activities and across different industrial sectors. Keywords: group risk, human safety, individual risk, Life Quality Index, railway, risk acceptance, structure, target reliability}, language = {en} } @article{DiamantidisSykoraLenzi, author = {Diamantidis, Dimitris and S{\´y}kora, Miroslav and Lenzi, Daniele}, title = {Optimising Monitoring: Standards, Reliability Basis and Application to Assessment of Roof Snow Load Risks}, series = {Structural Engineering International}, volume = {28}, journal = {Structural Engineering International}, number = {3}, publisher = {Taylor\&Francis}, doi = {10.1080/10168664.2018.1462131}, pages = {269 -- 279}, abstract = {This paper addresses the optimisation of monitoring and decision-making criteria regarding the future use of structures. The current state of practice in standards and reliability framework are initially summarised. A general methodology for obtaining cost-optimal decisions is then presented on the basis of limit state design, probabilistic reliability analysis and cost estimates. The implementation of the risk-based approach is illustrated in a case study dealing with the roof of a stadium located in northern Italy. As the roof fails to comply with the requirements of the Eurocodes, the installation of a permanent monitoring system is recommended to allow for a real-time reliability assessment. The results demonstrate the potential of monitoring systems and probabilistic reliability analysis for supporting decisions regarding safety measures such as snow removal or temporary closure of the stadium, as well as reflecting the need to implement the discussed procedures in future standards.}, language = {en} } @inproceedings{DiamantidisSykora, author = {Diamantidis, Dimitris and S{\´y}kora, Miroslav}, title = {Implementing Information Gained through Structural Health Monitoring - Proposal for Standards}, series = {13th International Conference on Applications of Statistics and Probability in Civil Engineering, Mai 2019, Seoul, Korea}, booktitle = {13th International Conference on Applications of Statistics and Probability in Civil Engineering, Mai 2019, Seoul, Korea}, abstract = {With exception of a few issues such as design by testing, current standards do not include guidelines on the use and the quantification of value of additional information gained through Structural Health Monitoring (SHM). This contribution summarizes a recently developed draft of the guideline for practicing engineers in the framework of the EU-COST project 1402 and illustrates its application in engineering decision-making. Besides continuous and periodic monitoring, visual inspection, non-destructive evaluation and proof loading are included herein as a simple form of SHM. The guideline is independent of a type of structure, construction materials, loading, and of environmental conditions. It aims at a wide field of application including design of new structures, assessment of existing structures and type specific monitoring of a population of structures. The decision process related to the use of SHM is presented first together with relevant decision objectives and variables. Performance indicators are summarized and discussed with respect to the performance objectives. The evaluation of monitoring strategies based on life cycle costs is exposed and the selection of optimal intervention actions including safety measures is shown in representative case studies. The results demonstrate the potential of the use of monitoring to support engineering decisions and reflect though the practical benefits from the application of the guideline.}, language = {en} } @inproceedings{Briem, author = {Briem, Ulrich}, title = {Neue Methode zur Bestimmung der Biegesteifigkeit von Drahtseilen}, series = {Der Kran - Leistungssteigerung, Leichtbau und Automatisierung : 27. Internationale Kranfachtagung 2019 : Begleitband zur Kranfachtagung am 07. M{\"a}rz 2019 in Bochum}, booktitle = {Der Kran - Leistungssteigerung, Leichtbau und Automatisierung : 27. Internationale Kranfachtagung 2019 : Begleitband zur Kranfachtagung am 07. M{\"a}rz 2019 in Bochum}, editor = {Scholten, Jan}, publisher = {Selbstverlag der Ruhr-Universit{\"a}t Bochum}, address = {Bochum}, isbn = {3-89194-226-5}, pages = {103 -- 112}, language = {de} } @inproceedings{Briem, author = {Briem, Ulrich}, title = {Lebensdauerverhalten verdichteter Seildr{\"a}hte}, series = {Ilmenauer Drahttag 2019}, booktitle = {Ilmenauer Drahttag 2019}, publisher = {ISLE Steuerungstechnik und Leistungselektronik}, address = {Ilmenau}, isbn = {978-3- 938843-96-3}, pages = {73 -- 82}, language = {de} } @inproceedings{DiamantidisSykoraBertacca, author = {Diamantidis, Dimitris and S{\´y}kora, Miroslav and Bertacca, Elena}, title = {Obsolescence Rate: Framework, Analysis and Influence on Risk Acceptance Criteria}, series = {6th International Symposium on Life-Cycle Civil Engineering (IALCCE), Ghent, Belgium}, booktitle = {6th International Symposium on Life-Cycle Civil Engineering (IALCCE), Ghent, Belgium}, abstract = {Buildings are major long lasting assets of the society and business enterprises and form a significant part of infrastructure management. They require continual maintenance and in many cases they can become inap-propriate for their original purpose due to obsolescence and are demolished. The present contribution ex-plores the obsolescence of buildings and in particular the definitions of obsolescence, the related influenc-ing factors and the associated uncertainties. Thereby definitions of the obsolescence rate based on the physi-cal and useful (service) life are clarified. The experienced useful life of buildings in Finland, Germany and North America is statistically analysed, utilizing available databases, and comparisons with the design (minimum) working life specified in standards are made. The probability of not exceeding the required min-imum service life is evaluated and discussed. Whereas many factors affecting the obsolescence rate are be-yond the control of civil engineers, particular attention needs to be paid to cases where the service life of the structure is determined by physical aspects related to deterioration. These cases are identified and recom-mendations to improve structural design are offered. The service life and the related renewal rate is influ-encing the risk acceptance criteria as given in ISO 2394. Such criteria are derived on the basis of economic optimization and the LQI marginal safety costs principle. A statistical model for the renewal rate is obtained and its influence on the target reliability is investigated for a representative failure limit state. The influence of the obsolescence rate is quantified and critically disputed.}, language = {en} } @article{FrazzicaPalombaDawoudetal., author = {Frazzica, Andrea and Palomba, Valeria and Dawoud, Belal and Gull{\`i}, Giuseppe and Brancato, Vincenza and Sapienza, Alessio and Vasta, Salvatore and Freni, Angelo and Costa, Fabio and Restuccia, Giovanni}, title = {Design, realization and testing of an adsorption refrigerator based on activated carbon/ethanol working pair}, series = {Applied Energy}, volume = {174}, journal = {Applied Energy}, publisher = {Elsevier}, doi = {10.1016/j.apenergy.2016.04.080}, pages = {15 -- 24}, abstract = {In the present paper design, realization and testing of a novel small scale adsorption refrigerator prototype based on activated carbon/ethanol working pair is described. Firstly, experimental activity has been carried out for identification of the best performing activated carbon available on the market, through the evaluation of the achievable thermodynamic performance both under air conditioning and refrigeration conditions. Once identified the best performing activated carbon, the design of the adsorber was developed by experimental dynamic performance analysis, carried out by means of the Gravimetric-Large Temperature Jump (G-LTJ) apparatus available at CNR ITAE lab. Finally, the whole 0.5 kW refrigerator prototype was designed and built. First experimental results both under reference air conditioning and refrigeration cycles have been reported, to check the achievable performance. High Specific Cooling Powers (SCPs), 95 W/kg and 50 W/kg, for air conditioning and refrigeration respectively, were obtained, while the COP ranged between 0.09 and 0.11, thus showing an improvement of the current state of the art. (C) 2016 Elsevier Ltd. All rights reserved.}, language = {en} } @article{ChatzitakisDawoud, author = {Chatzitakis, Paris and Dawoud, Belal}, title = {An alternative approach towards absorption heat pump working pair screening}, series = {Renewable Energy}, volume = {110}, journal = {Renewable Energy}, publisher = {Pergamon-Elsevier}, organization = {PERGAMON-ELSEVIER SCIENCE LTD}, doi = {10.1016/j.renene.2016.08.014}, pages = {47 -- 58}, abstract = {The successful market penetration of modern absorption heat pumps (AHP) today is critically dependent on their thermodynamic performance as well as other key factors like cost, reliability and inherent safety. Conventional AHPs have a proven record in the first two aspects but crucial shortcomings in the last two. For this reason it has been imperative to search for alternative working pairs that could potentially provide comparable performance while also satisfying the rest of the conditions to the best extent possible. As part of a systematic approach towards this direction, a detailed cycle analysis was performed, utilizing an idealized AHP system containing a real working pair, which enabled the identification of five dimensionless parameters and key thermophysical properties that influence the system's thermodynamic efficiency and the circulation ratio. In order to validate those findings, these parameters were calculated and compared between conventional and alternative AHP refrigerants. It turned out that low molecular weight ratios between absorbent and refrigerant have a beneficial effect on both coefficient of performance and the circulation ratio. Furthermore, both the refrigerant acentric factor and the absorbent vaporization enthalpy shall be minimized to obtain better performance. (C) 2016 Elsevier Ltd. All rights reserved.}, language = {en} } @article{DechantFedulovChashinetal., author = {Dechant, Eduard and Fedulov, Feodor and Chashin, Dmitri V. and Fetisov, Leonid Y. and Fetisov, Yuri K. and Shamonin (Chamonine), Mikhail}, title = {Low-frequency, broadband vibration energy harvester using coupled oscillators and frequency up-conversion by mechanical stoppers}, series = {Smart Materials and Structures}, volume = {26}, journal = {Smart Materials and Structures}, number = {6}, publisher = {IOP Publishing}, doi = {10.1088/1361-665X/aa6e92}, abstract = {The frequencies of ambient vibrations are often low (below 30 Hz). A broadband (3 dB bandwidth is larger than 10 Hz at an acceleration amplitude of 9.81 m s(-2)) vibration based energy harvester is proposed for transducing mechanical energy at such low frequencies into electrical energy. The mechanical setup converts low frequency mechanical vibrations into high frequency resonance oscillations of the transducer. This conversion is done by mechanical impacts on two mechanical stoppers. The originality of the presented design is that both low-frequency and high-frequency oscillators are permanently mechanically coupled. In the equivalent mechanical circuit, this coupling is achieved by connecting the ends of the stiff spring to both seismic masses, whereas one seismic mass (collison member) is also attached to the soft spring used as the constitutive element of a low-frequency oscillator. Further, both mechanical oscillators are not realized as conventional cantilever beams. In particular, the high frequency oscillator with the natural frequency of 340 Hz is a disc-shaped diaphragm with attached piezoelectric elements and a seismic mass. It is shown that it is possible to convert mechanical vibrations with acceleration amplitude of 9.81 m s(-2) in the region between approximately 7 and 25 Hz into electrical power larger than 0.1 mW with the maximum value of 0.8 mW. A simplified mathematical model based on piecewise linear coupled oscillators shows good agreement with experimental results. The ways to enhance the performance of the harvester and improve agreement with experiments are discussed.}, language = {en} } @article{daSilvaMotaHinckelRoccoetal., author = {da Silva Mota, Fabio Antonio and Hinckel, Jose Nivaldo and Rocco, Evandro Marconi and Schlingloff, Hanfried}, title = {Modeling and Analysis of a LOX/Ethanol Liquid Rocket Engine}, series = {Journal of Aerospace Technology and Management}, volume = {10}, journal = {Journal of Aerospace Technology and Management}, publisher = {Inst Aeronautica \& Espaco-IAE}, doi = {10.5028/jatm.v10.914}, abstract = {This work studies the performance and dry mass of the under development LOX/Ethanol L75 liquid rocket engine. To this end, an object-oriented program written in C++ was developed. The program is intended to be versatile and easily extensible in order to analyze different configurations of liquid rocket engines. The UML (Unified Modeling Language) tool is used to model the architecture of the codes. UML diagrams help to visualize the code structure and the communication between objects, enabling a high degree of abstraction. The cryogenics Vulcain and HM7B engines power cycles along with the staged-combustion SSME engine perform the verification of the codes. Finally, the influence of changes in design parameters on the performance and dry mass of the L75 rocket engine is analyzed.}, language = {en} } @article{Dawoud, author = {Dawoud, Belal}, title = {On the development of an innovative gas-fired heating appliance based on a zeolite-water adsorption heat pump; system description and seasonal gas utilization efficiency}, series = {Applied Thermal Engineering}, volume = {72}, journal = {Applied Thermal Engineering}, number = {2}, publisher = {Elsevier}, doi = {10.1016/j.applthermaleng.2014.09.008}, pages = {323 -- 330}, abstract = {The main objective of this work is to introduce an innovative hybrid heating appliance incorporating a gas condensing boiler and a zeolite-water adsorption heat pump. The condensing boiler is applied to drive the zeolite-water heat pump for the heating base-load and to assist the heat pump in the so called "mixed operation" mode, in which both the heat pump and the condensing boiler are working in series to cover medium heating demands. Peak heating demands are covered by the condensing boiler in the so called "direct heating" mode. The three operation modes of the hybrid heating appliance have been technically described. In addition, the laboratory test conditions for estimating the seasonal heating performance according to the German Guideline VDI 4650-2 have been introduced. For both heating systems 35/28 °C and 55/45 °C, which represent the typical operating conditions of floor and high temperature radiating heating systems in Europe, seasonal heating gas utilization efficiencies of 1.34 and 1.26 have been measured, respectively with a ground heat source. In two field test installations in one-family houses in Germany, the introduced heating appliance showed 27\% more seasonal gas utilization efficiency for heating and domestic hot water production, which is equivalent to a CO2-emission reduction of 20\% compared to the gas condensing boiler technology.}, language = {en} } @article{PalombaDawoudSapienzaetal., author = {Palomba, Valeria and Dawoud, Belal and Sapienza, Alessio and Vasta, Salvatore and Frazzica, Andrea}, title = {On the impact of different management strategies on the performance of a two-bed activated carbon/ethanol refrigerator: An experimental study}, series = {Energy conversion and management}, volume = {142}, journal = {Energy conversion and management}, publisher = {Elsevier}, doi = {10.1016/j.enconman.2017.03.055}, pages = {322 -- 333}, abstract = {In the present work, an experimental study on a lab-scale adsorption refrigerator, based on activated carbon/ethanol working pair is reported. An extensive testing campaign has been carried out at the CNR ITAE laboratory, with multiple aims. First, the performance has been evaluated in terms of both COP and Specific Cooling Power (SCP), under different boundary conditions, including both air conditioning and refrigeration applications. Attractive SCPs, up to 180 W/kg and 70 W/kg for air conditioning and refrigeration, respectively, were measured. Under the same conditions, COP between 0.17 and 0.08 were obtained. In addition, different management strategies, namely, heat recovery between adsorbers and re-allocation of phase durations, were evaluated to identify their influence on the system. Both strategies confirmed the possibility of increasing COP and SCP up to 40\% and 25\%, respectively. Moreover, a design analysis based on the experimental results has been carried out, to suggest possible improvements of the system. The obtained results demonstrated the possibility of employing a non-toxic refrigerant like ethanol reaching performance comparable with other harmful refrigerants like ammonia and methanol. (C) 2017 Elsevier Ltd. All rights reserved.}, language = {en} } @article{NiemetzHaenninenSchoepe, author = {Niemetz, Michael and H{\"a}nninen, Risto and Schoepe, Wilfried}, title = {On the Transition from Potential Flow to Turbulence Around a Microsphere Oscillating in Superfluid 4He}, series = {Journal of low temperature physics}, volume = {187}, journal = {Journal of low temperature physics}, number = {3-4}, publisher = {Springer Nature}, doi = {10.1007/s10909-017-1745-7}, pages = {195 -- 220}, abstract = {The flow of superfluid around a translationally oscillating sphere, levitating without mechanical support, can either be laminar or turbulent, depending on the velocity amplitude. Below a critical velocity that scales as and is temperature independent below 1 K, the flow is laminar (potential flow). Below 0.5 K, the linear drag force is caused by ballistic phonon scattering that vanishes as until background damping, measured in the empty cell, becomes dominant for K. Increasing the velocity amplitude above leads to a transition from potential flow to turbulence, where the large turbulent drag force varies as . In a small velocity interval \% above , the flow is unstable below 0.5 K, switching intermittently between both patterns. From time series recorded at constant temperature and driving force, the lifetimes of both phases are analyzed statistically. We observe metastable states of potential flow which, after a mean lifetime of 25 min, ultimately break down due to vorticity created by natural background radioactivity. The lifetimes of the turbulent phases have an exponential distribution, and the mean increases exponentially with . We investigate the frequency at which the vortex rings are shed from the sphere. Our results are compared with recent data of other authors on vortex shedding by moving a laser beam through a Bose-Einstein condensate. Finally, we show that our observed transition to turbulence belongs to the class of "supertransient chaos" where lifetimes of the turbulent states increase faster than exponentially.}, language = {en} } @article{BraunGebhardMatysiketal., author = {Braun, Peter and Gebhard, J{\"u}rgen and Matysik, Frank-Michael and Rabl, Hans-Peter}, title = {Potential Technical Approaches for Improving Low-Temperature NOx Conversion of Exhaust Aftertreatment Systems}, series = {Chemie Ingenieur Technik}, volume = {90}, journal = {Chemie Ingenieur Technik}, number = {6}, publisher = {WILEY-VCH}, doi = {10.1002/cite.201700122}, pages = {762 -- 773}, abstract = {Lean-burn engines, such as diesel engines, are widely used in mobile and stationary applications. Operation of lean-burn engines leads to formation of distinct amounts of nitrogen oxides (NO and NO2). Efficient aftertreatment is mandatory to meet legal requirements, especially at low exhaust temperatures, as for the future a decline of the exhaust temperature level can be predicted due to improved engine efficiencies. Within this review, potential technical solutions to enhance the DeNO(x)-aftertreatment efficiency at low exhaust temperatures are presented.}, language = {en} } @article{KasparRablMayer, author = {Kaspar, Marcel and Rabl, Hans-Peter and Mayer, Wolfgang}, title = {Ion-Molecule Reaction for the Selective Detection of Hydrocarbons in Diesel Exhaust Gas}, series = {Chemie Ingenieur Technik}, volume = {90}, journal = {Chemie Ingenieur Technik}, number = {6}, publisher = {WILEY-VCH}, doi = {10.1002/cite.201700075}, pages = {826 -- 834}, abstract = {The hydrocarbons present in the diesel exhaust gas are analyzed. A mass spectrometer is used for the measurements, and it operates on the basis of an ion-molecule reaction. This method is especially suitable because it is selective, is as free of fragments as possible, and is highly sensitive to the species that need to be measured. The study shows that numerous hydrocarbons in diesel exhaust gas can be identified. In particular, three molecules, ethyne, ethene and propene, were analyzed online in-depth on an engine test bench under different engine operating conditions.}, language = {en} } @article{BarzSeligerMarxetal., author = {Barz, Tilman and Seliger, Dominik and Marx, Klemens and Sommer, Andreas and Walter, Sebastian F. and Bock, Hans Georg and Koerkel, Stefan}, title = {State and state of charge estimation for a latent heat storage}, series = {Control Engineering Practice}, volume = {72}, journal = {Control Engineering Practice}, publisher = {Pergamon-Elsevier d.}, doi = {10.1016/j.conengprac.2017.11.006}, pages = {151 -- 166}, abstract = {A nonlinear state observer is designed for a thermal energy storage with solid/liquid phase change material (PCM). Using a physical 2D dynamic model, the observer reconstructs transient spatial temperature fields inside the storage and estimates the stored energy and the state of charge. The observer has been successfully tested with a lab-scale latent heat storage with a single pass tube bundle and the phase change material located in a shell around each tube. It turns out that the observer robustly tracks the real process data with as few as four internal PCM temperature sensors. © 2017 Elsevier Ltd. All rights reserved.}, language = {en} } @article{Roesel, author = {R{\"o}sel, Birgit}, title = {Just-in-Time Teaching f{\"u}r einen Grundkurs Regelungstechnik - Ergebnisse und Auswirkungen der Profistufe des Zertifikats Hochschullehre}, series = {Didaktiknachrichten}, journal = {Didaktiknachrichten}, number = {06}, publisher = {Zentrum f{\"u}r Hochschuldidaktik (DiZ)}, pages = {66 -- 71}, language = {de} } @incollection{MuehlbauerRablRottengruber, author = {M{\"u}hlbauer, Christian and Rabl, Hans-Peter and Rottengruber, Hermann}, title = {Acoustic Optimization of Mechatronic Direct Injection Systems and Analysis of the Effects on Robustness in System Operation}, series = {SAE International Journal of Advances and Current Practices in Mobility}, volume = {4}, booktitle = {SAE International Journal of Advances and Current Practices in Mobility}, number = {1}, publisher = {SAE International, Warrendale, PA, United States}, issn = {2641-9645}, doi = {10.4271/2021-01-0671}, pages = {68 -- 77}, abstract = {The tightening of the emission legislation and political and social demands for sustainable mobility are forcing the automotive industry to develop complex, high precision mechatronic drive systems. The increasing precision of mechatronic components generally leads to an increase in structural excitation and thus to a rise in noise. The so-called ticking of the fuel injection system has a rather low sound pressure level compared to the residual engine noise. Nevertheless, the impulsive and high frequency noise character leads to a decline concerning the perception of comfort and sound quality. In order to identify the sound quality of fuel injection systems as a frontloading measure, a system test bench has been developed which represents the structure-borne and airborne sound radiation of the stand-alone injection system in a close to series configuration. In this paper, measures for the acoustic optimization of injection systems and their effects on the robustness of the system are discussed. The focus is on engine idling, since at this operating point the ticking of the injectors and high-pressure pump can be perceived most clearly due to the low masking effects of other noise sources. For this purpose, the injection parameters were measured during full engine operation and transferred to the system test bench. By using a special development control unit, it was possible to modify the parameters, quantify their influence on the acoustic behavior and, based on this, define NVH optimized control strategies. For the robustness evaluation of the NVH optimized control strategies, key functions of the injection system were analyzed under varying boundary conditions in system operation on an injection rate test bench.}, language = {en} } @incollection{WalterSchwanzerHagenetal., author = {Walter, Stefanie and Schwanzer, Peter and Hagen, Gunter and Haft, Gerhard and Dietrich, Markus and Rabl, Hans-Peter and Moos, Ralf}, title = {Hochfrequenzsensorik zur direkten Beladungserkennung von Benzinpartikelfiltern}, series = {Automobil-Sensorik 3}, booktitle = {Automobil-Sensorik 3}, editor = {Tille, Thomas}, publisher = {Springer Vieweg}, address = {Berlin}, isbn = {978-3-662-61259-0}, doi = {10.1007/978-3-662-61260-6_7}, pages = {185 -- 208}, abstract = {In Folge der Versch{\"a}rfung der gesetzlichen Abgasnormen wurden f{\"u}r direkt-einspritzende Benzinmotoren Partikelfilter notwendig. Zur Beladungs{\"u}berwachung k{\"o}nnen aufgrund stark unterschiedlicher Rahmenbedingungen die aus Dieselmotoren bekannten Systeme, wie dem Differenzdrucksensor, nur eingeschr{\"a}nkt {\"u}bernommen werden. Ein hochfrequenzbasiertes Verfahren koppelt mittels Antennen elektromagnetische Wellen in das Filtergeh{\"a}use ein, deren Ausbreitungsverhalten durch die dielektrischen Eigenschaften des eingelagerten Rußes beeinflusst wird. Hierdurch kann bei Auswertung von Transmissionsd{\"a}mpfung oder Resonanzfrequenzen die Rußbeladung direkt detektiert werden.}, language = {en} } @misc{SchwanzerMieslingerRabletal., author = {Schwanzer, Peter and Mieslinger, Johann and Rabl, Hans-Peter and Dietrich, Markus and Haft, Gerhard and Walter, Stefanie and Hagen, Gunter and Moos, Ralf and Gaderer, Matthias}, title = {Monitoring of a Particulate Filter for Gasoline Direct Injection Engines with a Radio-Frequency-Sensor}, series = {11th International Exhaust Gas and Particulate Emissions Forum, 3.-4.3.2020, Ludwigsburg, Germany}, journal = {11th International Exhaust Gas and Particulate Emissions Forum, 3.-4.3.2020, Ludwigsburg, Germany}, abstract = {In order to comply with future emission regulations, the use of particulate filters in vehicles with direct injection gasoline engines is essential. The current amount of soot and ash in the filter is calculated by a soot load model in the electronic control unit in combination with a differential pressure sensor determining the pressure drop over the particulate filter. Active regeneration is initiated if the calculated amount of soot or the measured differential pressure is too high. This is associated with additional fuel consumption. An on-board diagnosis for the particulate filter is currently not part of the Euro 6d emission standard. For future exhaust emission standards, on-board diagnosis or active monitoring of the particulate filter is conceivable. One of the benefits of monitoring is the fact that unnecessary active regenerations can be avoided. As a result, there is no additional fuel consumption due to misinterpretations of the amount of soot in the filter. For active monitoring of the particulate filter, a radiofrequency (RF-) sensor, that detects the soot loading of the filter with electromagnetic waves directly, can be used. Such a system has the advantage that by utilizing the filter as a sensor more precise information about the current state of the filter, e.g. a possible damage, can be provided. Worst-case considerations of filter damages, tested at an engine test bench show the advantages which are entailed by a system like that. By means of partial regeneration of the particulate filter it is demonstrated how the remaining amount of soot in the filter can be detected in a better way in comparison to the differential pressure sensor by using the RF-sensor.}, language = {en} } @techreport{EmmertGlueckFreilingeretal., author = {Emmert, Michael and Gl{\"u}ck, Sven and Freilinger, Eva and Brandl, Dominik and Schindler, Sebastian and Kaul, Nicolas and Rasp, Franziska and Akstaller, Monika and Wetzel, Daniel and Jupke, Michael and Bodensteiner, Michael and Hohlfeld, Philipp and B{\"o}hm, Kevin and Brem, Theresa and Hammer, Pascal and Singer, Thomas and Karing, Maria and Schneider, Viola and Ostermeier, Tobias}, title = {FMS-Berichte (Mai 2021)}, editor = {Meier, Hans and Niemetz, Michael and Reindl, Andrea}, address = {Regensburg}, doi = {10.35096/othr/pub-1915}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-19155}, pages = {99}, abstract = {Dieser Bericht entstand auf Initiative der Studierenden des 2020 neu gegr{\"u}ndeten Masterstudiengangs „Elektro- und Informationstechnik (MEI)", die an der Pflichtlehrveranstaltung „Forschungsmethoden und Seminar (FMS)" im Wintersemester 2020/21 teilnahmen. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuf{\"u}hren. Daher war geeignete Literatur zu einem individuellen Thema zu recherchieren, Ver{\"o}ffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erarbeiten und diese in einem Vortrag zu pr{\"a}sentieren. Parallel dazu erfolgte im Theorieteil die entsprechende Hinf{\"u}hrung zu den verschiedenen Elementen der Wissenschaftskommunikation: • Bedeutung der Wissenschaftskommunikation f{\"u}r die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualit{\"a}t aufgefundener Fachliteratur, Auswahl geeigneter Materialien f{\"u}r die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertsch{\"a}tzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschul{\"o}ffentlicher Pr{\"a}sentation der Ergebnisse • F{\"u}hren m{\"u}ndlicher wissenschaftlicher Diskurse Nachdem die Masterstudierenden in der Regel {\"u}ber noch keine eigene wissenschaftliche Forschungserfahrung bzw. -inhalte verf{\"u}gen, lag der w{\"a}hlbare Schwerpunkt der Literatursuche auf der Bearbeitung von vorgegeben aktuellen technischen oder gesellschaftspolitischen Forschungsthemen.}, language = {de} } @techreport{OPUS4-2062, title = {Energienutzungsplan f{\"u}r die Gemeinde Sinzing}, editor = {Neuleitner, Nikolaus and Steffens, Oliver}, organization = {Hochschule f{\"u}r ANgewandte Wissenschaften Regensburg}, language = {de} } @article{Briem, author = {Briem, Ulrich}, title = {Die neue VDI 2500 : Faserseilwissen kompakt}, series = {Logistik f{\"u}r Unternehmen}, journal = {Logistik f{\"u}r Unternehmen}, number = {11-12}, pages = {36 -- 37}, abstract = {Die Richtlinie VDI 2500 „Faserseile" hat 1990 erstmals zusammenfassend den Stand der Technik auf dem Gebiet der Faserseile dargestellt und wertvolle Infor-mationen {\"u}ber Aufbau, Auswahl, Konfek-tionierung und {\"U}berwachung von Faser-seilen gegeben. Die jetzt erscheinende zweite Auflage enth{\"a}lt eine Vielzahl wichtiger technischer Neuerungen f{\"u}r die Praxis. Zu nennen sind hier die hochfesten Fasern und deren Beschichtung sowie die erstmals systematisch aufgef{\"u}hrten Sei-lendverbindungen und ein Ausblick auf die zuk{\"u}nftig bedeutsamen sogenannten Hybridseile. Eine Checkliste hilft bei der richtigen Auswahl und Bemessung von Faserseilen. Bei den Normen wurde - soweit m{\"o}glich - auf europ{\"a}ische Normen verwiesen.}, language = {de} } @article{Briem, author = {Briem, Ulrich}, title = {Umlaufbiegewechselzahl von verdichteten Seildr{\"a}hten}, series = {Draht}, journal = {Draht}, number = {6}, pages = {14 -- 15}, language = {de} } @inproceedings{BuettnerBohigasBoladerasGottschalketal., author = {B{\"u}ttner, Johannes and Bohigas Boladeras, Pere and Gottschalk, Philipp and Kucera, Markus and Waas, Thomas}, title = {Performance Isolation of Co-located Workload in a Container-based Architecture for Automobile}, series = {9th International Conference on Ambient Computing, Applications, Services and Technologies 2019, 22-26.09.2019, Porto, Portugal}, booktitle = {9th International Conference on Ambient Computing, Applications, Services and Technologies 2019, 22-26.09.2019, Porto, Portugal}, isbn = {978-1-61208-739-9}, pages = {31 -- 37}, abstract = {As the development in the automotive sector is facing upcoming challenges, the demand for in-vehicle computing power capacity increases and the need for flexible hardware and software structures arises, allowing dynamic managament of resources. In this new scenario, software components are to be added, removed, updated and migrated between computing units. To isolate the software components from each other and allow its orchestration, a container-based virtualization approach is being tested throughout this research. The analysis focuses on the question if this virtualization technology could be an option to ensure an interference-free operation. Four different sample applications from the automotive environment are tested for their susceptibility to resource contention. The research on the one hand shows that CPU and memory used by an application can be largely isolated with this technology, but on the other hand, it becomes apparent that support for I/O-heavy usage is currently not implemented sufficiently for container engines.}, language = {en} } @misc{Waas, author = {Waas, Thomas}, title = {Energy Monitoring and Saving in Medium-Sized Companies}, series = {5th International Congress on Energy Efficiency \& Energy Related Materials (ENEFM 2019), Gebze Technical University, Turkey, Book of Abstracts}, journal = {5th International Congress on Energy Efficiency \& Energy Related Materials (ENEFM 2019), Gebze Technical University, Turkey, Book of Abstracts}, editor = {Ahmet, Yavuz Oral and Zehra, Banu Oral and Mehmet, Sezer and Mehmet, Emre Ak{\"o}z and Seda, Kol and Onur, Alp and Aksan, Vala and Can, A{\c{s}}kan and Gamze, Sekicek}, pages = {21}, language = {en} } @inproceedings{BrunnerRoederKuceraetal., author = {Brunner, Stefan and R{\"o}der, J{\"u}rgen and Kucera, Markus and Waas, Thomas}, title = {Automotive E/E-architecture enhancements by usage of ethernet TSN}, series = {13th Workshop on Intelligent Solutions in Embedded Systems (WISES), 12-13 June 2017, Hamburg, Germany}, booktitle = {13th Workshop on Intelligent Solutions in Embedded Systems (WISES), 12-13 June 2017, Hamburg, Germany}, publisher = {IEEE}, doi = {10.1109/WISES.2017.7986925}, pages = {9 -- 13}, abstract = {A huge upheaval emerges from the transition to autonomous vehicles in the domain of road vehicles, ongoing with a change in the vehicle architecture. Many sensors and Electronic Control Units are added to the current vehicle architecture and further safety requirements like reliability become even more necessary. In this paper we present a potential evolution of the Electrical/Electronic-Architecture, including a Zone Architecture, to enable future functionality. We reveal the impact on the communication network concerning these architectures and present a potential communication technology to facilitate such architectures.}, subject = {Kraftfahrzeug}, language = {en} } @misc{SchrollDecker, author = {Schroll-Decker, Irmgard}, title = {Rezension zu: Ethik des Wissens. Freiheit und Verantwortung der Wissenschaft in Zeiten des Klimawandels. oekom Verlag (M{\"u}nchen) 2019. ISBN 978-3-96238-163-9}, series = {socialnet Rezensionen}, journal = {socialnet Rezensionen}, issn = {2190-9245}, language = {de} } @article{BraunRablMatysik, author = {Braun, Peter and Rabl, Hans-Peter and Matysik, Frank-Michael}, title = {Investigations on the Liquid-Phase Decomposition of AdBlue Urea for the Selective Catalytic Reduction Process}, series = {Chemie Ingenieur Technik}, volume = {91}, journal = {Chemie Ingenieur Technik}, number = {7}, publisher = {Wiley}, doi = {10.1002/cite.201800055}, pages = {961 -- 968}, abstract = {Difficulties in decomposing AdBlue to ammonia limit the applicability of selective catalytic reduction systems at low exhaust temperatures. Investigations on the decomposition of AdBlue in the liquid phase under elevated pressure at temperatures up to 165 degrees C were carried out. Besides effects of inorganic catalysts, the impact of pH on urea decomposition was examined. After dissolution in aqueous phase, the compounds ZnO, WO3, and MoO3 were found to be effective in liquid-phase AdBlue decomposition. However, the efficiency was dropping significantly over few hours. Decomposition of AdBlue urea was also found to be favored for alkaline and acidic conditions.}, language = {en} } @article{BraunDurnerRabletal., author = {Braun, Peter and Durner, Bernhard and Rabl, Hans-Peter and Matysik, Frank-Michael}, title = {Investigations on the decomposition of AdBlue urea in the liquid phase at low temperatures by an electrochemically induced pH shift}, series = {Monatshefte f{\"u}r Chemie}, volume = {150}, journal = {Monatshefte f{\"u}r Chemie}, number = {9}, publisher = {Springer}, doi = {10.1007/s00706-019-02406-6}, pages = {1633 -- 1641}, abstract = {Ammonia-based selective catalytic reduction (SCR) systems are the most widely used technology for reduction of nitrogen oxide emissions from lean-burn engines such as diesel engines. However, at low exhaust temperatures, the SCR process is limited by difficulties in the decomposition of the ammonia precursor urea, which is carried on-board using an aqueous solution "AdBlue". In this study, the decomposition of AdBlue urea induced by electrical current and the resulting associated pH shifts were investigated in a divided cell configuration in the liquid phase. The decomposition was found to be favored in both electrochemical compartments, anodic and cathodic, at temperatures of 60-80 degrees C compared to a reference without electrochemical treatment. In addition to the determination of ammonia contents using an ammonia sensor, IC/HPLC analyses were carried out for each sample. Different side products such as biuret, nitrate, cyanuric acid, ammelide, and others were formed. In the anodic compartment, nitrate formation could be observed due to oxidation of ammonia at the electrode surface. [GRAPHICS] .}, language = {en} } @misc{Weiss, author = {Weiss, Nils}, title = {Vulnerabilities of OBD2 Dongles}, series = {RCAR Annual Conference, 2018, Munich, Germany}, journal = {RCAR Annual Conference, 2018, Munich, Germany}, language = {en} } @misc{Weiss, author = {Weiss, Nils}, title = {Vulnerabilities of Connected Cars and beyond}, series = {Applied Research Colloquium, 2019, Universit{\`a} Padua, Italy}, journal = {Applied Research Colloquium, 2019, Universit{\`a} Padua, Italy}, language = {en} } @inproceedings{MaeuleRabl, author = {M{\"a}ule, Paul and Rabl, Hans-Peter}, title = {Correlation of Oil Emissions with Particulate Emissions of Gasoline Engines}, series = {Internationales AVL-Forum Abgas- und Partikelemissionen, 20. und 21. Februar 2018, Ludwigsburg}, booktitle = {Internationales AVL-Forum Abgas- und Partikelemissionen, 20. und 21. Februar 2018, Ludwigsburg}, publisher = {AVL Deutschland}, address = {Mainz}, pages = {1 -- 9}, abstract = {Recent developments in exhaust gas legislation make it necessary to focus the research at the particulate emissions from gasoline engines and technologies for their reduction. In addition to the particulates resulting from the combustion of the fuel, the oil emissions represent another possible source for particulate emissions. This paper presents a measurement method which can be used to quantify stationary as well as dynamic oil emissions of gasoline engines. Furthermore, the correlation between the oil emissions and the particulate emissions is the focus of the investigations. Conventional methods for the determination of the oil emissions, such as the gravimetric and the volumetric measurement, are unsuitable since they require long engine operation times to provide useful results. These methods therefore do not allow a fast online measurements during the dynamic operation. For this reason, a new measuring method was used, which allows for a time-resolved online measurement of the oil emissions. This measurement method is based on the sulfur tracer method, which uses the sulfur that is naturally contained in the engine oil as a tracer. The sulfur concentration in the exhaust gas is determined by using an Ion-Molecule-Reaction mass spectrometer. The determination of the particulate emissions corresponds to the PMP regulation. The studies carried out under steady state and dynamic conditions show a clear correlation between the oil consumption and the number of particulates in the exhaust gas. In the case of the dynamic measurements it could also be shown that time-resolved measurements of the oil consumption are possible with the used measurement setup. In addition, it was shown that the number of particulates does not influence the measurement of the SO2-concentration. Furthermore, the different effects of burned and unburned oil emissions have been evaluated by the dosing of the oil into the exhaust gas. The overall conclusion of the measurements shows a strong influence of the oil emissions on the particulate emissions. Therefore, it is crucial to reduce the oil emissions. Possible approaches for this reduction can be improved turbocharger sealing concepts, new piston ring designs or more efficient oil separators for the crankcase ventilation system.}, language = {en} } @inproceedings{SmolareckFaisstSchneider, author = {Smolareck, Elisabeth and Faisst, Holger and Schneider, Ralph}, title = {Modellbasierte Korrektur von Inertialsensor-Signalen - Ein Schritt auf dem Weg zum hochautomatisierten Fahren}, series = {Konferenz: AALE 2018 - 15. Fachkonferenz, Das Forum f{\"u}r Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft 01.03.2018 - 02.03.2018 in K{\"o}ln, Deutschland}, booktitle = {Konferenz: AALE 2018 - 15. Fachkonferenz, Das Forum f{\"u}r Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft 01.03.2018 - 02.03.2018 in K{\"o}ln, Deutschland}, publisher = {VDE-Verlag}, address = {Berlin}, isbn = {978-3-8007-4522-7}, pages = {1 -- 10}, abstract = {Infolge neuer Zielsetzungen im Automobilbereich, wie z. B. der Weiterentwicklung von Fahrerassistenzsystemen hin zum hochautomatisierten Fahren (HAF), ergeben sich erh{\"o}hte Anforderungen an die Signalg{\"u}te der im Fahrzeug eingesetzten Inertialsensoren f{\"u}r Drehraten und Beschleunigungen. Da deren Erf{\"u}llung {\"u}ber einen hardwarebasierten Ansatz nicht immer m{\"o}glich und sinnvoll ist, strebt die Firma Continental eine Software-L{\"o}sung zur modellbasierten Verbesserung dieser Sensorsignale an.}, language = {de} } @article{GaertnerRablZink, author = {G{\"a}rtner, Uwe and Rabl, Hans-Peter and Zink, Uwe}, title = {Exhaust Gas Aftertreatment of the Future}, series = {MTZ worldwide}, volume = {79}, journal = {MTZ worldwide}, number = {7-8}, publisher = {Springer}, doi = {10.1007/s38313-018-0060-2}, pages = {70 -- 75}, language = {en} } @article{KuepperArtmannPischingeretal., author = {K{\"u}pper, Carsten and Artmann, Christina and Pischinger, Stefan and Rabl, Hans-Peter}, title = {Lube-Oil Dilution of Gasoline Direct-Injection Engines with Ethanol Fuels}, series = {MTZ worldwide}, volume = {74}, journal = {MTZ worldwide}, number = {9}, publisher = {Springer}, address = {Berlin}, doi = {10.1007/s38313-013-0090-8}, pages = {64 -- 69}, language = {en} } @inproceedings{EberhartChungHaumeretal., author = {Eberhart, Philip and Chung, Tek Shan and Haumer, Anton and Kral, Christian}, title = {Open Source Library for the Simulation of Wind Power Plants}, series = {Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015}, booktitle = {Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015}, address = {Link{\"o}ping}, doi = {10.3384/ecp15118929}, pages = {929 -- 936}, abstract = {This paper presents the new open source Modelica libraryWindPowerPlants. For the economic assessment of either a wind power plant or an entire wind park, the accurate prediction of the energy output is essential. Such prediction is usually performed by means of calculations based on statistical wind data. The proposed WindPowerPlants library is capable of assessing the energy output both for statistical and real wind data based on time domain simulations. In the presented version of the library wind turbine models are modeled with pitch control. The generator models have variable speed and an optional connector to the mains. The entire library is based on power balance conditions and losses are fully neglected. Yet, the library can be extended towards more detailed models considering different types of losses. The structure and components of the library are presented. Simulations examples are shown and compared with reference data. The applicability of the proposed WindPowerPlants library is demonstrated and possible enhancements are discussed.}, language = {en} } @article{KurzweilScheuerpflug, author = {Kurzweil, Peter and Scheuerpflug, Wolfgang}, title = {State-of-charge monitoring and battery diagnosis of different lithium ion chemistries using impedance spectroscopy}, series = {Batteries}, volume = {7}, journal = {Batteries}, number = {1}, doi = {10.3390/batteries7010017}, pages = {16}, abstract = {For lithium iron phosphate batteries (LFP) in aerospace applications, impedance spectroscopy is applicable in the flat region of the voltage-charge curve. The frequency-dependent pseudocapacitance at 0.15 Hz is presented as useful state-of-charge (SOC) and state-of-health (SOH) indicator. For the same battery type, the prediction error of pseudocapacitance is better than 1\% for a quadratic calibration curve, and less than 36\% for a linear model. An approximately linear correlation between pseudocapacitance and Ah battery capacity is observed as long as overcharge and deep discharge are avoided. We verify the impedance method in comparison to the classical constant-current discharge measurements. In the case of five examined lithium-ion chemistries, the linear trend of impedance and SOC is lost if the slope of the discharge voltage curve versus SOC changes. With nickel manganese cobalt (NMC), high impedance modulus correlates with high SOC above 70\%.}, language = {en} } @article{RomeisKostrovKramarenkoetal., author = {Romeis, Dirk and Kostrov, Sergei A. and Kramarenko, Elena Yu and Stepanov, Gennady V. and Shamonin (Chamonine), Mikhail and Saphiannikova, M.}, title = {Magnetic-field-induced stress in confined magnetoactive elastomers}, series = {Soft Matter}, volume = {16}, journal = {Soft Matter}, number = {39}, publisher = {Royal Society of Chemistry}, address = {Cambridge}, doi = {10.1039/D0SM01337D}, pages = {9047 -- 9058}, abstract = {We present a theoretical approach for calculating the state of stress induced by a uniform magnetic field in confined magnetoactive elastomers of arbitrary shape. The theory explicitly includes the magnetic field generated by magnetizable spherical inclusions in the sample interior assuming a non-linear magnetization behavior. The initial spatial distribution of particles and its change in an external magnetic field are considered. This is achieved by the introduction of an effective demagnetizing factor where both the sample shape and the material microstructure are taken into account. Theoretical predictions are fitted to the stress data measured using a specifically designed experimental setup. It is shown that the theory enables the quantification of the effect of material microstructure upon introducing a specific microstructural factor and its derivative with respect to the extensional strain in the undeformed state. The experimentally observed differences between isotropic and anisotropic samples, compliant and stiff elastomer matrices are explained.}, language = {en} } @article{BelyaevaKramarenkoShamoninChamonine, author = {Belyaeva, Inna A. and Kramarenko, Elena Yu and Shamonin (Chamonine), Mikhail}, title = {Magnetodielectric effect in magnetoactive elastomers: Transient response and hysteresis}, series = {POLYMER}, volume = {127}, journal = {POLYMER}, publisher = {ELSEVIER}, doi = {10.1016/j.polymer.2017.08.056}, pages = {119 -- 128}, abstract = {Magnetodielectric properties of magnetoactive elastomers comprising micrometer-sized iron particles dispersed in compliant elastomer matrices are experimentally studied in stepwise time-varying dc magnetic fields. It is found that imposition of magnetic field significantly increases both the effective lossless permittivity of these composite materials as well as their effective conductivity. These magnetodielectric effects are more pronounced for larger concentrations of soft-magnetic filler particles and softer elastomer matrices. The largest observed relative change of the effective dielectric constant in the maximum magnetic field of 0.57 T is of the order of 1000\%. The largest observed absolute change of the loss tangent is approximately 0.8. The transient response of the magnetodielectric effect to a step magnetic-field excitation can be rather complex. It changes from a simple monotonic growth with time for small magnetic-field steps (<0.1 T) to a non-monotonic behavior with a significant rapidly appearing overshoot for large magnetic-field steps (>0.3 T). The settling time to the magnetic-field step excitation can reach roughly 1000 s and it depends on the applied magnetic field and sample composition. There is also significant hysteresis of the magnetodielectric effect on the externally applied magnetic field. These findings are attributed to the rearrangement of ferromagnetic filler particles in external magnetic fields. The results will be useful for understanding and predicting the transient behavior of magnetoactive elastomers in applications where the control magnetic field is time dependent. (C) 2017 Elsevier Ltd. All rights reserved.}, language = {en} } @article{SorokinBelyaevaShamoninChamonineetal., author = {Sorokin, Vladislav V. and Belyaeva, Inna A. and Shamonin (Chamonine), Mikhail and Kramarenko, Elena Yu}, title = {Magnetorheological response of highly filled magnetoactive elastomers from perspective of mechanical energy density: Fractal aggregates above the nanometer scale?}, series = {Physical Review E}, volume = {95}, journal = {Physical Review E}, number = {6}, publisher = {Amer Physical Soc}, doi = {10.1103/PhysRevE.95.062501}, abstract = {The dynamic shear modulus of magnetoactive elastomers containing 70 and 80 mass \% of carbonyl iron microparticles is measured as a function of strain amplitude via dynamic torsion oscillations in various magnetic fields. The results are presented in terms of the mechanical energy density and considered in the framework of the conventional Kraus model. The form exponent of the Kraus model is further related to a physical model of Huber et al. [Huber et al., J. Phys.: Condens. Matter 8, 409 (1996)] that uses a realistic representation for the cluster network possessing fractal structure. Two mechanical loading regimes are identified. At small strain amplitudes the exponent beta of the Kraus model changes in an externally applied magnetic field due to rearrangement of ferromagnetic-filler particles, while at large strain amplitudes, the exponent beta seems to be independent of the magnetic field. The critical mechanical energy characterizing the transition between these two regimes grows with the increasing magnetic field. Similarities between agglomeration and deagglomeration of magnetic filler under simultaneously applied magnetic field and mechanical shear and the concept of jamming transition are discussed. It is proposed that the magnetic field should be considered as an additional parameter to the jamming phase diagram of rubbers filled with magnetic particles.}, language = {en} } @article{DechantFedulovFetisovetal., author = {Dechant, Eduard and Fedulov, Feodor and Fetisov, Leonid Y. and Shamonin (Chamonine), Mikhail}, title = {Bandwidth Widening of Piezoelectric Cantilever Beam Arrays by Mass-Tip Tuning for Low-Frequency Vibration Energy Harvesting}, series = {Applied Science}, volume = {7}, journal = {Applied Science}, number = {12}, publisher = {MDPI}, organization = {MDPI AG}, doi = {10.3390/app7121324}, abstract = {Wireless sensor networks usually rely on internal permanent or rechargeable batteries as a power supply, causing high maintenance efforts. An alternative solution is to supply the entire system by harvesting the ambient energy, for example, by transducing ambient vibrations into electric energy by virtue of the piezoelectric effect. The purpose of this paper is to present a simple engineering approach for the bandwidth optimization of vibration energy harvesting systems comprising multiple piezoelectric cantilevers (PECs). The frequency tuning of a particular cantilever is achieved by changing the tip mass. It is shown that the bandwidth enhancement by mass tuning is limited and requires several PECs with close resonance frequencies. At a fixed frequency detuning between subsequent PECs, the achievable bandwidth shows a saturation behavior as a function of the number of cantilevers used. Since the resonance frequency of each PEC is different, the output voltages at a particular excitation frequency have different amplitudes and phases. A simple power-transfer circuit where several PECs with an individual full wave bridge rectifier are connected in parallel allows one to extract the electrical power close to the theoretical maximum excluding the diode losses. The experiments performed on two- and three-PEC arrays show reasonable agreement with simulations and demonstrate that this power-transfer circuit additionally influences the frequency dependence of the harvested electrical power.}, language = {en} } @inproceedings{SykoraDiamantidisMarkovaetal., author = {S{\´y}kora, Miroslav and Diamantidis, Dimitris and Markova, J. and Masciotta, Maria Giovanna}, title = {Optimizing in-situ testing for historic masonry structures: a case study}, series = {International Conference on Sustainable Materials, Systems and Structures (SMSS 2019) : Durability, Monitoring and Repair of Structures, 20-22 March 2019, Rovinj, Croatia}, booktitle = {International Conference on Sustainable Materials, Systems and Structures (SMSS 2019) : Durability, Monitoring and Repair of Structures, 20-22 March 2019, Rovinj, Croatia}, editor = {Baričević, Ana and Jelčić Rukavina, Marija and Damjanović, Domagoi and Guadagnini, Maurizio}, publisher = {RILEM Publications}, isbn = {978-1-5108-9296-5}, pages = {684 -- 691}, language = {en} } @article{SchwanzerRablLodersetal., author = {Schwanzer, Peter and Rabl, Hans-Peter and Loders, S. and Seifert, P. and Himmelstoss, S. and Gaderer, Matthias}, title = {Difference in the Tailpipe Particle Number by Consideration of Sub-23-nm Particles for Different Injection Settings of a GDI Engine}, series = {Emission control science and technology}, volume = {5}, journal = {Emission control science and technology}, number = {1}, publisher = {Springer Nature}, doi = {10.1007/s40825-019-0114-1}, pages = {7 -- 22}, abstract = {The purpose of this study was to investigate the characteristic of nanoparticles under consideration of sub-23-nm particles from a 1.8-l direct injection (DI) gasoline engine under stoichiometric air/fuel conditions in the exhaust gas system. For future CO2 challenges, the usage of DI-instead of port fuel injection (PFI)-gasoline engines is unavoidable. Therefore, a state of the art particle management program-particle number (PN) system, the Horiba SPCS (2100) with an integrated CPC (condensation particle counter), was recalibrated from a 50\% cutoff (D-50\%) at 23 nm down to a cutoff at 10 nm and the PCRF (particle concentration reduction factor) for sizes smaller than 23 nm was checked. Two different modal points, out of a representative Real Driving Emission (RDE) cycle, were investigated with both calibrations, D-50\%=10 nm and D-50\%=23 nm. For these different load points, the fuel pressure (FUP) and the start of injection (SOI) were varied, to represent the difference in the structure and the ratio conc((10 nm))/conc((23 nm)) of the nanoparticle emissions. The particle characterization includes the particle number (PN), the particle size distribution (PSD), and the particle mass (PM). The particle number was measured with Horiba SPCS (2100). The particle size distribution was analyzed with a Grimm differential mobility analyzer (DMA) in combination with a Faraday cup electrometer (FCE). Micro Soot and Pegasor were used to determine the PM, and an optical characterization was done with a 120-kV Phillips CM12 transmission electron microscope (TEM). The position of all particle measurement systems was downstream the three-way catalyst (TWC). The results of this investigation showed that a higher injection pressure decreases the PN (without consideration of sub-23-nm particles) in general. The ratio conc((10 nm))/conc((23 nm)) was therefore higher, because smaller particles, especially ash particles, were less reduced from the FUP. This means higher FUP tends to a higher ratio. For the SOI, the main reasons of the ratio differences were explained by an encroachment between the injection jet and the piston, the valve and the wall.}, language = {en} } @article{KalitaSnarskiiShamoninChamonineetal., author = {Kalita, Viktor M. and Snarskii, Andrei A. and Shamonin (Chamonine), Mikhail and Zorinets, Denis}, title = {Effect of single-particle magnetostriction on the shear modulus of compliant magnetoactive elastomers}, series = {Physical review E}, volume = {95}, journal = {Physical review E}, number = {3}, publisher = {American Physical Society}, doi = {10.1103/PhysRevE.95.032503}, abstract = {The influence of an external magnetic field on the static shear strain and the effective shear modulus of a magnetoactive elastomer (MAE) is studied theoretically in the framework of a recently introduced approach to the single-particle magnetostriction mechanism [V. M. Kalita et al., Phys. Rev. E 93, 062503 (2016)]. The planar problem of magnetostriction in an MAE with magnetically soft inclusions in the form of a thin disk (platelet) having the magnetic anisotropy in the plane of this disk is solved analytically. An external magnetic field acts with torques on magnetic filler particles, creates mechanical stresses in the vicinity of inclusions, induces shear strain, and increases the effective shear modulus of these composite materials. It is shown that the largest effect of the magnetic field on the effective shear modulus should be expected in MAEs with soft elastomer matrices, where the shear modulus of the matrix is less than the magnetic anisotropy constant of inclusions. It is derived that the effective shear modulus is nonlinearly dependent on the external magnetic field and approaches the saturation value in magnetic fields exceeding the field of particle anisotropy. It is shown that model calculations of the effective shear modulus correspond to a phenomenological definition of effective elastic moduli and magnetoelastic coupling constants. The obtained theoretical results compare well with known experimental data. Determination of effective elastic coefficients in MAEs and their dependence on magnetic field is discussed. The concentration dependence of the effective shear modulus at higher filler concentrations has been estimated using the method of Pade approximants, which predicts that both the absolute and relative changes of the magnetic-field-dependent effective shear modulus will significantly increase with the growing concentration of filler particles.}, language = {en} } @misc{AltmannRablGaderer, author = {Altmann, Robert and Rabl, Hans-Peter and Gaderer, Matthias}, title = {Ph{\"a}nomenologische Untersuchung des Einspritzverhaltens von Pflanzen{\"o}lkraftstoff}, series = {3. Tagung der Fuels Joint Research Group (FJRG) "Kraftstoffe f{\"u}r die Mobilit{\"a}t von Morgen"}, journal = {3. Tagung der Fuels Joint Research Group (FJRG) "Kraftstoffe f{\"u}r die Mobilit{\"a}t von Morgen"}, language = {de} } @misc{AltmannGadererRabl, author = {Altmann, Robert and Gaderer, Matthias and Rabl, Hans-Peter}, title = {Pr{\"u}fstandsuntersuchungen an einem DEUTZ NRMM Motor mit Raps{\"o}lkraftstoff und Optimierung des Betriebs- und Emissionsverhaltens durch statistische Versuchsplanung}, series = {18. Internationaler Fachkongress "Kraftstoffe der Zukunft 2021" - digital \& international vernetzt!, online}, journal = {18. Internationaler Fachkongress "Kraftstoffe der Zukunft 2021" - digital \& international vernetzt!, online}, language = {de} } @article{WalterSchwanzerSteineretal., author = {Walter, Stefanie and Schwanzer, Peter and Steiner, Carsten and Hagen, Gunter and Rabl, Hans-Peter and Dietrich, Markus and Moos, Ralf}, title = {Mixing Rules for an Exact Determination of the Dielectric Properties of Engine Soot Using the Microwave Cavity Perturbation Method and Its Application in Gasoline Particulate Filters}, series = {Sensors}, volume = {22}, journal = {Sensors}, number = {9}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/s22093311}, pages = {1 -- 17}, abstract = {In recent years, particulate filters have become mandatory in almost all gasoline-powered vehicles to comply with emission standards regarding particulate number. In contrast to diesel applications, monitoring gasoline particulate filters (GPFs) by differential pressure sensors is challenging due to lower soot masses to be deposited in the GPFs. A different approach to determine the soot loading of GPFs is a radio frequency-based sensor (RF sensor). To facilitate sensor development, in previous work, a simulation model was created to determine the RF signal at arbitrary engine operating points. To ensure accuracy, the exact dielectric properties of the soot need to be known. This work has shown how small samples of soot-loaded filter are sufficient to determine the dielectric properties of soot itself using the microwave cavity perturbation method. For this purpose, mixing rules were determined through simulation and measurement, allowing the air and substrate fraction of the sample to be considered. Due to the different geometry of filter substrates compared to crushed soot samples, a different mixing rule had to be derived to calculate the effective filter properties required for the simulation model. The accuracy of the determined mixing rules and the underlying simulation model could be verified by comparative measurements on an engine test bench.}, language = {en} } @article{MikhaeilGadererDawoud, author = {Mikhaeil, Makram and Gaderer, Matthias and Dawoud, Belal}, title = {Experimental Investigation of the Adsorption and Desorption Kinetics on an Open-Structured Asymmetric Plate Heat Exchanger; Matching Between Small-Scale and Full-Scale Results}, series = {Frontiers in Energy Research}, volume = {10}, journal = {Frontiers in Energy Research}, publisher = {Frontiers}, doi = {10.3389/fenrg.2022.818486}, pages = {1 -- 15}, abstract = {This paper introduces the results of an experimental study on the adsorption and desorption kinetics of a commercially available, open-structured asymmetric plate heat exchanger adapted to act as an adsorber/desorber for the application in adsorption heat transformation processes. In addition, a volumetric large temperature jump (V-LTJ) kinetic setup was applied to measure the adsorption and desorption kinetics of a small-scale adsorbent sample prepared dedicatedly to be representative for the adsorbent domain inside the investigated adsorber plate heat exchanger (APHE). All kinetic results of the small-scale adsorbent sample and the APHE were fitted into exponential forms with a single characteristic time constant (τ) with a coefficient of determination (R2) better than 0.9531. A very good matching between the small-scale and full-scale adsorption kinetic measurements was obtained, with an average relative deviation of 12.3\% in the obtained τ-values. In addition, the kinetic data of the small-scale adsorbent sample were utilized for estimating the expected specific instantaneous and moving average powers of the evaporator/condenser heat exchanger. The average relative deviation (ARD) between the moving average specific evaporator powers obtained from the small-scale and the full-scale measurements amounts between 5.4 and 15.1\%.}, language = {en} } @article{SteiningerGadererDawoud, author = {Steininger, Peter and Gaderer, Matthias and Dawoud, Belal}, title = {Assessment of the Annual Transmission Heat Loss Reduction of a Refurbished Existing Building with an Advanced Solar Selective Thermal Insulation System}, series = {Sustainability}, volume = {13}, journal = {Sustainability}, number = {13}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/su13137336}, pages = {1 -- 19}, abstract = {A numerical parameter sensitivity analysis of the design parameters of the recently published solar selective thermal insulation system (SATIS) has been carried out to enhance its thermal and optical properties. It turned out that the insulation properties of SATIS can be effectively improved by reducing the length of the glass closure element. Increasing the area share of the light conducting elements (LCEs) and decreasing their length-to-diameter (L/D) ratio were identified as key parameters in order to increase the solar gain. Two SATIS variants were compared with the same wall insulation without SATIS in a yearly energetic performance assessment. The SATIS variant with 10 mm length of the closure element, 44.2\% area share of LCE, as well as front and rear diameters of 12 mm/9 mm shows an 11.8\% lower transmission heat loss over the heating period than the wall insulation without SATIS. A new methodology was developed to enable the implementation of the computed solar gains of SATIS in 1D simulation tools. The result is a radiant heat flow map for integration as a heat source in 1D simulation models. A comparison between the 1D and 3D models of the inside wall heat fluxes showed an integral yearly agreement of 98\%.}, language = {en} } @article{SavelievFetisovChashinetal., author = {Saveliev, Dmitry and Fetisov, Leonid Y. and Chashin, Dmitri V. and Fetisov, Yuri K. and Khon, Anastasia and Shamonin (Chamonine), Mikhail}, title = {Effects of ferromagnetic-material thickness on magnetoelectric voltage transformation in a multiferroic heterostructure}, series = {Smart Materials and Structures}, volume = {30}, journal = {Smart Materials and Structures}, number = {6}, publisher = {IOP PUBLISHING}, doi = {10.1088/1361-665X/abf6c0}, abstract = {A magnetoelectric (ME) voltage transformer is fabricated on the basis of a ferromagnetic (FM)-piezoelectric (PE) heterostructure comprising two equally thick laminated layers of an amorphous FM alloy and a piezoceramic lead zirconate-titanate layer sandwiched between them. The structure, placed inside an excitation coil, is electrically poled and magnetized in the direction of the long axis. The primary voltage is applied to the coil and the secondary voltage is measured between the electrodes of the PE material. It is shown for the first time that the change in the total thickness of magnetic layers significantly influences the transformer ' s characteristics. At the largest total thickness of FM layers of 138 mu m, the open-circuit voltage transformation ratio K has a maximum value of about 20, and the power transfer efficiency eta at a matched resistive load of about 20 k omega reaches 45\%. The variation of the control magnetic field in the range of 0-21.6 kA m(-1) makes it possible to change the voltage transformation ratio K from zero to the maximum value. A simple model allows one to calculate the dependence of the characteristics of the ME transformer on the frequency of the primary voltage, thickness of the FM layers, control magnetic field, and the load.}, language = {en} } @article{VerezBorriCrespoetal., author = {V{\´e}rez, David and Borri, Emiliano and Crespo, Alicia and Zsembinszki, Gabriel and Dawoud, Belal and Cabeza, Luisa F.}, title = {Experimental Study of a Small-Size Vacuum Insulated Water Tank for Building Applications}, series = {Sustainability}, volume = {13}, journal = {Sustainability}, number = {10}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/su13105329}, pages = {1 -- 11}, abstract = {Insulation of thermal energy storage tanks is fundamental to reduce heat losses and to achieve high energy storage efficiency. Although water tanks were extensively studied in the literature, the enhancement of the insulation quality is often overlooked. The use of vacuum insulation has the potential to significantly reduce heat losses without affecting the dimension of the storage system. This paper shows for the first time the results of the heat losses tests done for a 0.535 m3 water tank for residential building applications built with a double wall vacuum insulation. The different tests show that the rate of heat losses strictly depends on the temperature distribution inside the tank at the beginning of the experiment. Compared to a conventional water tank insulated with conventional materials, the U-value of the lateral surface was reduced by almost three times (from 1.05 W/K·m2 to 0.38 W/K·m2) using vacuum insulation. However, the bottom part, which is usually used to place the support parts and the piping, is the critical design part of those tanks acting as a thermal bridge with the ambient and enhancing heat losses.}, language = {en} } @article{BelyaevaKleppLemmeletal., author = {Belyaeva, Inna A. and Klepp, J{\"u}rgen and Lemmel, Hartmut and Shamonin (Chamonine), Mikhail}, title = {Feasibility of Probing the Filler Restructuring in Magnetoactive Elastomers by Ultra-Small-Angle Neutron Scattering}, series = {Applied Sciences}, volume = {11}, journal = {Applied Sciences}, number = {10}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/app11104470}, pages = {1 -- 9}, abstract = {Ultra-small-angle neutron scattering (USANS) experiments are reported on isotropic magnetoactive elastomer (MAE) samples with different concentrations of micrometer-sized iron particles in the presence of an in-plane magnetic field up to 350 mT. The effect of the magnetic field on the scattering curves is observed in the scattering vector range between 2.5 x 10(-5) and 1.85 x 10(-4) angstrom(-1). It is found that the neutron scattering depends on the magnetization history (hysteresis). The relation of the observed changes to the magnetic-field-induced restructuring of the filler particles is discussed. The perspectives of employing USANS for investigations of the internal microstructure and its changes in magnetic field are considered.}, language = {en} } @article{GamischGadererDawoud, author = {Gamisch, Bernd and Gaderer, Matthias and Dawoud, Belal}, title = {On the Development of Thermochemical Hydrogen Storage: An Experimental Study of the Kinetics of the Redox Reactions under Different Operating Conditions}, series = {Applied Sciences}, volume = {11}, journal = {Applied Sciences}, number = {4}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/app11041623}, pages = {1 -- 15}, abstract = {This work aims at investigating the reduction/oxidation (redox) reaction kinetics on iron oxide pellets under different operating conditions of thermochemical hydrogen storage. In order to reduce the iron oxide pellets (90\% Fe2O3, 10\% stabilizing cement), hydrogen (H2) is applied in different concentrations with nitrogen (N2), as a carrier gas, at temperatures between between 700 ∘C and 900 ∘C, thus simulating the charging phase. The discharge phase is triggered by the flow of a mixture out of steam (H2O) and N2 at different concentrations in the same temperature range, resulting in the oxidizing of the previously reduced pellets. All investigations were carried out in a thermo-gravimetric analyzer (TGA) with a flow rate of 250mL/min. To describe the obtained kinetic results, a simplified analytical model, based on the linear driving force model, was developed. The investigated iron oxide pellets showed a stable redox performance of 23.8\% weight reduction/gain, which corresponds to a volumetric storage density of 2.8kWh/(L bulk), also after the 29 performed redox cycles. Recalling that there is no H2 stored during the storage phase but iron, the introduced hydrogen storage technology is deemed very promising for applications in urban areas as day-night or seasonal storage for green hydrogen.}, language = {en} } @article{GeilfussDawoud, author = {Geilfuß, Kristina and Dawoud, Belal}, title = {Analytical investigation of a zeolite-NaY-water adsorption heat and cold storage and its integration into a steam power process}, series = {Energy}, volume = {195}, journal = {Energy}, number = {March}, publisher = {Elsevier}, doi = {10.1016/j.energy.2020.116977}, abstract = {tabilizing the effects of greenhouse gas emissions on the atmosphere is a key step towards solving the global climate change problems. Storage technologies play an essential role in compensating the discrepancy between surplus energy and peak times. Sorption processes, in particular, offer an environment friendly way for almost loss-free heat (of adsorption or absorption) and cold storage. This work is dedicated first to analytically investigate the potential of applying NaY-Water/Zeolite as a working pair for heat and cold storage upon utilizing high temperature heat. It turned out that, the mass of the adsorber heat exchanger increases the useful specific heat stored from 229 kWh/tzeolite for the ideal storage to 538 kWh/tzeolite or even higher depending on the thermal capacity of the adsorber heat exchanger (AdsHX). Contrary to that trend, COP will decrease with increasing the thermal capacity of the AdsHX. Sensible heat losses between charging and discharging phases do have a negative effect on both stored heating capacity and COP. In addition, an innovative hybrid steam power cum adsorption storage process is introduced and analytically investigated at different ambient conditions and time scenarios for on-peak and off-peak durations over the day. The introduced hybrid process seems quite promising in achieving electrical power production and efficiency enhancements during peak load durations. The extent of enhancing both performance indicators increases with increasing the ambient temperature difference between peak and off-peak times.}, language = {en} } @article{SnarskiiShamoninChamonineYuskevich, author = {Snarskii, Andrei A. and Shamonin (Chamonine), Mikhail and Yuskevich, Pavel}, title = {Effective medium theory for the elastic properties of composite materials with various percolation thresholds}, series = {Materials}, volume = {13}, journal = {Materials}, number = {5}, publisher = {MPDI}, address = {Basel}, doi = {10.3390/ma13051243}, pages = {1 -- 19}, abstract = {It is discussed that the classical effective medium theory for the elastic properties of random heterogeneous materials is not congruous with the effective medium theory for the electrical conductivity. In particular, when describing the elastic and electro-conductive properties of a strongly inhomogeneous two-phase composite material, the steep rise of effective parameters occurs at different concentrations. To achieve the logical concordance between the cross-property relations, a modification of the effective medium theory of the elastic properties is introduced. It is shown that the qualitative conclusions of the theory do not change, while a possibility of describing a broader class of composite materials with various percolation thresholds arises. It is determined under what conditions there is an elasticity theory analogue of the Dykhne formula for the effective conductivity. The theoretical results are supported by known experiments and show improvement over the existing approach. The introduction of the theory with the variable percolation threshold paves the way for describing the magnetorheological properties of magnetoactive elastomers. A similar approach has been recently used for the description of magneto-dielectric and magnetic properties.}, language = {en} } @article{SnarskiiShamoninChamonineYuskevichetal., author = {Snarskii, Andrei A. and Shamonin (Chamonine), Mikhail and Yuskevich, Pavel and Saveliev, Dmitry V. and Belyaeva, Inna A.}, title = {Induced anisotropy in composite materials with reconfigurable microstructure: Effective medium model with movable percolation threshold}, series = {Physica A: Statistical Mechanics and its Applications}, volume = {560}, journal = {Physica A: Statistical Mechanics and its Applications}, number = {December}, publisher = {Elsevier}, doi = {10.1016/j.physa.2020.125170}, abstract = {In composite materials, with field-dependent restructuring of the filler material (changes in the mutual arrangement of inclusions), the presence of an external magnetic field induces anisotropy of the dielectric properties, even if the composite is isotropic in the absence of an external field. A modified effective medium approximation is proposed for the calculation of the components of effective permittivity within a class of composites with reconfigurable microstructure, where both phases (the filler and the matrix) are isotropic and the inclusions have spherical shape. The effective physical properties are calculated in the parallel and perpendicular directions to an applied field. The appearance of the anisotropy of the permittivity is simulated by the introduction of two not-equal, possibly variable (field-dependent) percolation thresholds. The implications, of the proposed theoretical approach, are demonstrated for the case of the dielectric properties of magnetoactive elastomers (MAEs). In MAEs with soft polymer matrices, the mutual arrangement of micrometer-sized magnetic inclusions can significantly change in an applied magnetic field. A reasonable agreement between theory and experiment at a measurement frequency of 1 kHz is found, and is improved in comparison to the previous models. The components of the effective permittivity tensor, characterizing the dielectric properties along the direction of the applied magnetic field and in the orthogonal direction, grow with an increasing field. This growth is more pronounced for the permittivity component in the field direction. The possible extensions of the theoretical model and future directions of research are discussed. The presented theoretical approach can be useful for the application-driven development of a number of smart materials, in particular electro- and magnetorheological gels, elastomers and fluids.}, language = {en} } @article{SavelievBelyaevaChashinetal., author = {Saveliev, Dmitry V. and Belyaeva, Inna A. and Chashin, Dmitri V. and Fetisov, Leonid Y. and Romeis, Dirk and Kettl, Wolfgang and Kramarenko, Elena Yu and Saphiannikova, M. and Stepanov, Gennady V. and Shamonin (Chamonine), Mikhail}, title = {Giant extensional strain of magnetoactive elastomeric cylinders in uniform magnetic fields}, series = {Materials}, volume = {13}, journal = {Materials}, number = {15}, publisher = {MDPI}, address = {Basel}, issn = {1996-1944}, doi = {10.3390/ma13153297}, pages = {1 -- 17}, abstract = {Elongations of magnetoactive elastomers (MAEs) under ascending-descending uniform magnetic fields were studied experimentally using a laboratory apparatus specifically designed to measure large extensional strains (up to 20\%) in compliant MAEs. In the literature, such a phenomenon is usually denoted as giant magnetostriction. The synthesized cylindrical MAE samples were based on polydimethylsiloxane matrices filled with micrometer-sized particles of carbonyl iron. The impact of both the macroscopic shape factor of the samples and their magneto-mechanical characteristics were evaluated. For this purpose, the aspect ratio of the MAE cylindrical samples, the concentration of magnetic particles in MAEs and the effective shear modulus were systematically varied. It was shown that the magnetically induced elongation of MAE cylinders in the maximum magnetic field of about 400 kA/m, applied along the cylinder axis, grew with the increasing aspect ratio. The effect of the sample composition is discussed in terms of magnetic filler rearrangements in magnetic fields and the observed experimental tendencies are rationalized by simple theoretical estimates. The obtained results can be used for the design of new smart materials with magnetic-field-controlled deformation properties, e.g., for soft robotics.}, language = {en} } @article{SavelievBelyaevaChashinetal., author = {Saveliev, Dmitry V. and Belyaeva, Inna A. and Chashin, Dmitri V. and Fetisov, Leonid Y. and Shamonin (Chamonine), Mikhail}, title = {Large Wiedemann effect in a magnetoactive elastomer}, series = {Journal of Magnetism and Magnetic Materials}, volume = {511}, journal = {Journal of Magnetism and Magnetic Materials}, number = {October}, publisher = {Elsevier}, doi = {10.1016/j.jmmm.2020.166969}, abstract = {Large twists of a soft tube (hollow cylinder) in helical magnetic fields are presented for the first time. Such a phenomenon is usually denoted as the Wiedemann effect. The tube is fabricated from a soft magnetoactive elastomer material with the shear modulus of about 56 kPa. The composite material comprises 80 mass\% of micrometer-sized iron particles embedded into a polydimethylsiloxane matrix. The circular magnetic field is generated by an electric current in a straight wire passing through the inner hole of the tube. The maximum value of approximately 350″/cm is observed in a longitudinal magnetic field of a few kA/m overlapped with a circumferential magnetic field of about 1.4 kA/m on the surface of the inner hole. A pronounced hysteresis in the dependence of the Wiedemann effect on the circular magnetic field is found. The ways to enhance the Wiedemann twist in magnetoactive elastomers are discussed. The observed large effect is promising for application in magnetic-field controlled torsional actuators, in particular for soft robotics.}, language = {en} } @article{AndersBriemNovaketal., author = {Anders, M. and Briem, Ulrich and Novak, G. and Steinbach, G.}, title = {Inspektionsintervalle im Blick}, series = {Technische Logistik}, journal = {Technische Logistik}, publisher = {Huss-Medien}, address = {Berlin}, pages = {14 -- 17}, language = {de} } @article{BrockKoderRabletal., author = {Brock, Damian and Koder, Alexander and Rabl, Hans-Peter and Touraud, Didier and Kunz, Werner}, title = {Optimising the biodiesel production process: Implementation of glycerol derivatives into biofuel formulations and their potential to form hydrofuels}, series = {Fuel}, volume = {264}, journal = {Fuel}, number = {March}, publisher = {Elsevier}, doi = {10.1016/j.fuel.2019.116695}, abstract = {A new biofuel concept is developed, enabling the usage of vegetable oils and glycerol derivatives in mixtures with biodiesel. This concept significantly enhances the biodiesel production's profitability and thus strongly contributes to the sustainability of future biofuels. After simple addition reactions with building block chemicals, less hydrophilic glycerol derivatives are obtained, which are compatible with biofuels. Even more, the products of the reactions of glycerol with acetone or butyric acid, referred to as solketal and tributyrin, respectively, lead to promising biofuels in mixtures with rapeseed oil and its biodiesel. Due to their low freezing points, they act as cloud and freezing point depressants, when added to vegetable oil/biodiesel blends. Further, since their viscosity is close to common biodiesel, biofuels containing high amounts of vegetable oil and even more glycerol derivatives than they arise during the biodiesel production can be obtained. Thus, this new class of biofuels enables adaptable compositions depending on the application and also the usage as drop-in fuel without any or just few percent of further additives. After optimising the formulations, ignition delay, exhaust gas recirculation, fuel consumption and combustion process measurements were performed in an unmodified upto-date diesel engine. The experiments showed that the properties of the formulated biofuels are either similar to or even better than diesel. The hydrotropy of the glycerol derivatives in these mixtures enables the potential to implement water into biofuels, so-called hydrofuels, reducing nitrogen oxide emissions and leading to further optimised dropin fuels.}, language = {en} } @article{FrazzicaBrancatoDawoud, author = {Frazzica, Andrea and Brancato, Vincenza and Dawoud, Belal}, title = {Unified Methodology to Identify the Potential Application of Seasonal Sorption Storage Technology}, series = {Energies}, volume = {13}, journal = {Energies}, number = {5}, publisher = {MPDI}, address = {Basel}, doi = {10.3390/en13051037}, pages = {1 -- 17}, abstract = {In this study, the definition of a new methodology for a preliminary evaluation of the working boundary conditions under which a seasonal thermal energy storage (STES) system operates is described. The approach starts by considering the building features as well as the reference heating system in terms of solar thermal collectors' technology, ambient heat sinks/source, and space heating distribution systems employed. Furthermore, it is based on a deep climatic analysis of the place where the STES needs to be installed, to identify both winter and summer operating conditions. In particular, the STES energy density is evaluated considering different space heating demands covered by the STES (ranging from 10\% up to 60\%). The obtained results demonstrate that this approach allows for the careful estimation of the achievable STES density, which is varies significantly both with the space heating coverage guaranteed by the STES as well as with the ambient heat source/sink that is employed in the system. This confirms the need for careful preliminary analysis to avoid the overestimation of the STES material volume. The proposed approach was then applied for different climatic conditions (e.g., Germany and Sweden) and the volume of one of the most attractive composite sorbent materials reported in the literature, i.e., multi-wall carbon nanotubes (MWCNT)-LiCl, using water as the working fluid, needed for covering the variable space heating demand in a Nearly Zero Energy Building (NZEB) was calculated. In the case of Swedish buildings, it ranges from about 3.5 m3 when 10\% of the space heating demand is provided by the STES, up to 11.1 m3 when 30\% of the space heating demand is provided by the STES.}, language = {en} } @book{FreniDawoudBonaccorsietal., author = {Freni, Angelo and Dawoud, Belal and Bonaccorsi, Lucio Maria and Chmielewski, Stefanie and Frazzica, Andrea and Calabrese, Luigi and Restuccia, Giovanni}, title = {Characterization of Zeolite-Based Coatings for Adsorption Heat Pumps}, publisher = {Springer}, address = {Berlin}, doi = {10.1007/978-3-319-09327-7}, pages = {96 S.}, abstract = {This book proposes a radically new approach for characterizing thermophysical and mechanical properties of zeolite-based adsorbent coatings for Adsorptive Heat Transformers (AHT). It presents a developed standard protocol for the complete characterization of advanced coated adsorbers. Providing an in-depth analysis of the different procedures necessary for evaluating the performance of adsorbers, it also presents an analysis of their stability under the hydrothermal and mechanical stresses during their entire life cycle. Adsorptive Heat Transformers (AHT), especially adsorption chillers and heat pumps, are considered to be promising technologies to increase thermal energy efficiency. Nevertheless, an overall increase in performance of this apparatus is necessary for them to be considered a mature technology to be used commercially. Development of innovative coated adsorbers can be perceived as a key issue for the enhancement of AHT technology. This procedure relies on the deposition, either by means of a binder or by direct crystallization, of the adsorbent material over a metallic heat exchanger, aiming at the improvement of the heat transfer between the external heat source and the adsorbent itself. This book offers a valuable resource to those working on the development of novel adsorbent materials and advanced adsorbent beds for heating and cooling applications. It is also intended for researchers interested in renewable energy and energy efficiency.}, language = {en} } @inproceedings{SchiedermeierRettnerSteineretal., author = {Schiedermeier, Maximilian and Rettner, Cornelius and Steiner, Marcel and M{\"a}rz, Martin}, title = {Dual-inverter control synchronization strategy to minimize the DC-link capacitor current}, series = {2020 IEEE Vehicle Power and Propulsion Conference (VPPC), 18 November 2020 - 16 December 2020, Gijon, Spain}, booktitle = {2020 IEEE Vehicle Power and Propulsion Conference (VPPC), 18 November 2020 - 16 December 2020, Gijon, Spain}, publisher = {IEEE}, doi = {10.1109/VPPC49601.2020.9330921}, pages = {1 -- 6}, abstract = {This paper proposes the possible switching synchronization strategies of an automotive dual-inverter against the background of minimizing the RMS DC-link capacitor current. The publication mainly focuses on the straight-ahead motion of a rear axle with one electric drive per wheel. In addition to it, a dual-inverter consisting of two subinverters with a common DC-link capacitor is taken into consideration. These sub-inverters each have three phases and are based on a 2-level voltage-source-topology. To control the electrical machines, the continuous Space-Vector-Modulation strategy is used. For this application, different control signal synchronization strategies of the two sub-inverters of the dualinverter are presented. Apart from the existing strategies, this paper proposes a new method, which inherits a compromise between low complexity and high effectiveness. In contrast to previous publications, the resulting capacitor currents are quantified and subsequentlyevaluated. This novel quantification, which is dependent on the dual-inverter's operating point, provides a base for targeted dimensioning of the capacitor. Moreover, this forms the foundation for further investigations of vehicle's cornering, as well as for the possible synchronization of stand-alone inverters. In the context of this publication, the presented results are verified by experimentally determined data of a motor-inverter system.}, language = {en} } @inproceedings{KoderZacherlRabletal., author = {Koder, Alexander and Zacherl, Florian and Rabl, Hans-Peter and Mayer, Wolfgang and Gruber, Georg and Dotzer, Thomas}, title = {Jatropha Oil as an Alternative Fuel for Modern Diesel Engines - Injection Characteristics and EGR-Compatibility}, series = {WCX 17: SAE World Congress 2017}, booktitle = {WCX 17: SAE World Congress 2017}, publisher = {SAE International}, doi = {10.4271/2017-01-5000}, abstract = {An effective way to reduce greenhouse gas emissions (GHGs) is to use rurally produced straight jatropha oil as a substitute for diesel fuel. However, the different physical and chemical properties of straight vegetable oils (SVOs) require a customized setup of the combustion engine, particularly of the injection timing and quantity. Therefore, this study demonstrates the differences in the injection and combustion processes of jatropha oil compared to diesel fuel, particularly in terms of its compatibility with exhaust gas recirculation (EGR). A 2.2 l common-rail diesel engine with a two-stage turbocharging concept was used for testing. To examine the differences in injection rate shaping of diesel fuel and jatropha oil, the injector was tested with an injection rate analyzer using both the fuels. To investigate the combustion process, the engine was mounted at an engine test bench and equipped with a cylinder pressure indication system. All limited emissions, as well as fuel consumption, were measured. Various injection strategies, boost and rail pressure levels were tested at different EGR rates in terms of their impact on the combustion process. EGR in particular offers a great potential in the case of jatropha oil combustion due to its oxygen content. In addition, the investigation of injection rate shaping in combination with cylinder pressure analysis allowed a detailed thermodynamic evaluation of the combustion process. Ignition delay (ID) was also analyzed using a new method to calculate the start of combustion (SOC)}, language = {en} } @article{ChatzitakisSafarovOpferkuchetal., author = {Chatzitakis, Paris and Safarov, Javid and Opferkuch, Frank and Dawoud, Belal and Hassel, Egon}, title = {Vapor pressures and activity coefficients of 2,2,2-trifluoroethanol in binary mixtures with 1,3-dimethyl-2-imidazolidinone and 2-pyrrolidone}, series = {Journal of Molecular Liquids}, volume = {305}, journal = {Journal of Molecular Liquids}, number = {May}, publisher = {Elsevier}, issn = {0167-7322}, doi = {10.1016/j.molliq.2020.112828}, abstract = {The vapor pressures of two binary mixtures containing 2-trifluoroethanol (TFE) + 1,3-dimethyl-2-imidazolidinone (DMI) and TFE + 2-pyrrolidone (PYR), were investigated at temperatures T = (274.15 to 423.15) K using two different static method installations. Both combinations were modelled using an extended Clausius-Clapeyron equation with concentration dependent parameters and the NRTL equation with temperature dependent parameters. The best fit was obtained using the NRTL equation.}, language = {en} } @article{HansenHoeblerPurretal., author = {Hansen, B. and Hoebler, Michael and Purr, S. and Meinhardt, J. and Merklein, M.}, title = {Basics for inline measurement of tribological conditions in series production of car body parts}, series = {IOP Conference Series: Materials Science and Engineering}, volume = {651}, journal = {IOP Conference Series: Materials Science and Engineering}, publisher = {IOP Publishing}, doi = {10.1088/1757-899x/651/1/012050}, abstract = {The quality of car body parts in series production is strongly dependent on the tribological behavior. Fluctuating material properties such as the sheet roughness and the amount of lubricant have an influence on the forming process. On the basis of large amounts of data it is possible to investigate the friction behavior in series production and to make process adjustments if required. Therefore, inline measurement systems have a great potential to detect the sheet roughness during the cutting process of blanks in the coil line. Furthermore, contactless systems are advantageous as they do not damage the surface. Nevertheless, the optical measuring is influenced by the lubricant layer on top of the surface. Therefore, the previously unknown impact of the lubricant on the measuring result is investigated. Within this study, stationary optical roughness measurements have been conducted using different amounts of lubricant on hot-dip galvanized EDT steel. The results demonstrate the influence of different amounts of lubricant on the sheet roughness measurement. Hence, it is possible to correct the inline measuring results and gain knowledge of fluctuating surface roughness. In addition, strip drawing test has been carried out to investigate the effect of fluctuating tribological conditions.}, language = {en} } @article{Briem, author = {Briem, Ulrich}, title = {Biegesteifigkeit von Drahtseilen}, series = {Technische Logistik}, journal = {Technische Logistik}, number = {11-12}, publisher = {Huss-Medien}, address = {Berlin}, pages = {24 -- 25}, language = {de} }