@article{ŁawrowskiBachmannSchreiner, author = {Ławrowski, Robert Damian and Bachmann, Michael and Schreiner, Rupert}, title = {Field emission arrays from graphite fabricated by laser micromachining}, series = {Journal of Vacuum Science \& Technology B}, volume = {40}, journal = {Journal of Vacuum Science \& Technology B}, number = {2}, publisher = {AIP Publishing}, doi = {10.1116/6.0001547}, abstract = {Laser micro structuring allows the manufacturing of conical shaped emitters on a graphitized carbon substrate without any additional treatment. Integral field emission measurements were performed in a diode configuration with a 50 µm mica spacer and a metalized Si-grid in a vacuum chamber at pressures of about 10-9 mbar. Emission currents up to 10 µA at a voltage of 1000 V (11 MV/m) with a positive current drift were observed for an array of 16 emitters. A strong modification of the emitter tip is noticeable after individual measurements. A comparable alteration of the surface is also achieved by an electrochemical treatment of the samples with a potassium hydroxide solution. However, the IV-measurements of such samples show higher onset voltages, but also higher integral emission currents. For all arrays an ideal FN behaviour is only noticeable at applied voltages below 625 V (7 MV/m). Numerical calculations indicate that the deviation in the FN-plot for higher voltage values is caused by the change of the effective work function.}, language = {en} } @article{ŁawrowskiPrommesbergerLangeretal., author = {Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Improvement of Homogenity and Aspect Ratio of Silicon Tips for Field Emission by Reactive-Ion Etching}, series = {Advances in materials science and engineering}, volume = {2014}, journal = {Advances in materials science and engineering}, publisher = {Hindawi}, doi = {10.1155/2014/948708}, abstract = {The homogeneity of emitters is very important for the performance of field emission (FE) devices. Reactive-ion etching (RIE) and oxidation have significant influences on the geometry of silicon tips. The RIE influences mainly the anisotropy of the emitters. Pressure has a strong impact on the anisotropic factor. Reducing the pressure results in a higher anisotropy, but the etch rate is also lower. A longer time of etching compensates this effect. Furthermore an improvement of homogeneity was observed. The impact of uprating is quite low for the anisotropic factor, but significant for the homogeneity. At low power the height and undercut of the emitters are more constant over the whole wafer. The oxidation itself is very homogeneous and has no observable effect on further variation of the homogeneity. This modified fabrication process allows solving the problem of inhomogeneity of previous field emission arrays.}, language = {en} } @article{ŁawrowskiPrommesbergerLangeretal., author = {Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Improvement of Homogeneity and Aspect Ratio of Silicon Tips for Field Emission by Reactive-Ion Etching}, series = {Advances in Materials Science and Engineering. Special issue: Advances in Smart Materials and Applications}, volume = {2014}, journal = {Advances in Materials Science and Engineering. Special issue: Advances in Smart Materials and Applications}, publisher = {Hindawi}, issn = {1687-8442}, doi = {10.1155/2014/948708}, pages = {1 -- 6}, abstract = {The homogeneity of emitters is very important for the performance of field emission (FE) devices. Reactive-ion etching (RIE) and oxidation have significant influences on the geometry of silicon tips. The RIE influences mainly the anisotropy of the emitters. Pressure has a strong impact on the anisotropic factor. Reducing the pressure results in a higher anisotropy, but the etch rate is also lower. A longer time of etching compensates this effect. Furthermore an improvement of homogeneity was observed. The impact of uprating is quite low for the anisotropic factor, but significant for the homogeneity. At low power the height and undercut of the emitters are more constant over the whole wafer. The oxidation itself is very homogeneous and has no observable effect on further variation of the homogeneity. This modified fabrication process allows solving the problem of inhomogeneity of previous field emission arrays.}, language = {en} } @incollection{ŁawrowskiPrommesbergerLangeretal., author = {Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Feldemissionselektronenquellen basierend auf Siliziumemittern mit hohen Aspektverh{\"a}ltnis}, series = {Forschungsbericht der OTH Regensburg 2013}, booktitle = {Forschungsbericht der OTH Regensburg 2013}, address = {Regensburg}, pages = {47 -- 48}, language = {de} } @article{LindnerPipaBrandenburgetal., author = {Lindner, Matthias and Pipa, Andrei V. and Brandenburg, Ronny and Schreiner, Rupert}, title = {Expansion of surface barrier discharge scrutinized}, series = {Plasma Sources Science and Technology}, volume = {31}, journal = {Plasma Sources Science and Technology}, number = {10}, publisher = {IOP Publishing}, doi = {10.1088/1361-6595/ac95bf}, abstract = {Developing the fundamentals for the electrical diagnostics of surface dielectric barrier discharges (SDBDs) is of enormous importance for several applications, for example, flow control and gas cleaning. The main challenge is to account for the discharge expansion along the dielectric surface. Typically, a linear expansion with the amplitude of the applied voltage is observed. In this work, we report on a step-wise SDBD expansion along the Al 2 O 3 dielectric surface. More specific, the discharge occupied a certain area after ignition, which remained constant until the voltage exceeded the critical amplitude V L . This absence of expansion is seen as a linear dependence of the discharge power on the applied voltage and it was additionally confirmed by photographs with long exposure times. This novel phenomenon is more pronounced for thicker dielectrics. It is suggested that the derivative of the charge-voltage characteristics can be used for the determination of all essential parameters of the simplest equivalent circuit of SDBDs. Moreover, it was shown that the derivative of the charge-voltage characteristics for the positive half-cycle of the discharge agrees numerically with the voltage dependence of the reactor capacitance derived from photographs. This agreement between both measurement methods indicates a similar step-wise expansion of the SDBD even if a voltage amplitude above V L is applied. …}, language = {en} } @article{BornmannMingelsDamsetal., author = {Bornmann, Benjamin and Mingels, Stephan and Dams, Florian and Prommesberger, Christian and Schreiner, Rupert and L{\"u}tzenkirchen-Hecht, Dirk and M{\"u}ller, G{\"u}nter}, title = {Electron spectrometer in adjustable triode configuration for photo-induced field emission measurements}, series = {The Review of scientific instruments}, volume = {83}, journal = {The Review of scientific instruments}, number = {1}, publisher = {American Institute of Physics}, address = {Melville, NY}, doi = {10.1063/1.3673475}, abstract = {We have constructed a new ultrahigh vacuum apparatus with a triode configuration for the systematic investigation of photo-induced field emission (PFE) from metallic or semiconducting cathodes. These are exposed to electric fields up to 400 MV∕m and laser irradiation by means of hole or mesh gates. Cathodes and gates are in situ exchangeable and adjustable with high precision to ensure a homogeneous extraction of electrons which are partially transmitted to the fixed electron spectrometer. Its hemispherical sector analyzer provides an energy resolution limit of 8 meV. The commissioning of the measurement system has been performed with a tungsten needle. Its temperature showed up in the high-energy tail of the electron spectrum, while its work function was derived from the spectral low-energy part combined with the integral current-voltage curve. First PFE measurements on B-doped Si-tip arrays yielded a small field emission current increase under green laser illumination. A shift and splitting of the energy spectra was observed which revealed different emission regimes as well as the photosensitivity of the cathode due to carrier excitation into the conduction band. For the full exploitation of the PFE system, a tunable laser over a wide eV-range is required.}, language = {en} } @article{ŁawrowskiPirkerKanekoetal., author = {Ławrowski, Robert Damian and Pirker, Luka and Kaneko, Keita and Kokubo, Hiroki and Bachmann, Michael and Ikuno, Takashi and Remskar, Maja and Schreiner, Rupert}, title = {Field emission from nanotubes and flakes of transition metal dichalcogenides}, series = {Journal of Vacuum Science and Technology B}, volume = {38}, journal = {Journal of Vacuum Science and Technology B}, number = {3}, publisher = {AIP Publishing}, doi = {10.1116/1.5140474}, pages = {032801}, abstract = {Transition metal dichalcogenides such as MoS2 and WS2 are low-dimensional semiconductor materials. MoS2 and WS2 nanotubes and flakes were grown by a chemical transport reaction under a temperature gradient. I2 was used as a transport agent for previously synthesized MoS2 and WS2, respectively. These multilayered nanotubes are indirect bandgap semiconductors with a bandgap depending on their diameter. WS2 flakes were prepared by the sulfurization of thin WOx flakes. To increase the field enhancement of such low-dimensional structures by a higher aspect ratio, two approaches were examined: (a) the MoS2 and WS2 nanotubes were attached individually by a focused ion beam with Pt on dry etched n-type Si pillars and (b) the WS2 flakes were grown directly on the surface of the (n-type and p-type) Si pillars. Integral field emission measurements were performed in a diode configuration with a 50 μm mica spacer in a vacuum chamber at pressures of about 10-9 mbar. At a voltage of 900 V (18 MV/m), the integral emission current from the nanotubes is up to 11 μA for the lateral mounted MoS2 and about 1.3 μA (1.0 μA) for the upright mounted WS2 (MoS2). The onset voltage for a current of 1 nA is about 550 V for MoS2 and 500 V for WS2, respectively. The voltage conversion factor is in the range of 6 × 104-8 × 104 cm-1 for the nanotubes. The mounted MoS2 flakes show a field emission current of about 6 μA at 18 MV/m in contrast to the directly grown WS2 flakes, which show a pronounced saturation regime and, therefore, a lower emission current of about 0.5 μA is reached at 1500 V (25 MV/m). The WS2 flakes show a two times higher (1 × 105 cm-1) voltage conversion factor in comparison to the MoS2 flakes (5 × 104 cm-1). The extracted characteristics of the current-limiting part show a difference in the behavior of the extracted current-limiting characteristics between the lateral (linear) and upright mounted (exponential) nanotubes and the MoS2 flakes. In contrast, the WS2 flakes show charge carrier depletion effects.}, language = {en} } @article{KleshchSerbunLuetzenkirchenHechtetal., author = {Kleshch, Victor I. and Serbun, Pavel and L{\"u}tzenkirchen-Hecht, Dirk and Orekhov, Anton and Ivanov, Victor E. and Prommesberger, Christian and Langer, Christoph and Schreiner, Rupert and Obraztsov, Alexander N.}, title = {A Comparative Study of Field Emission from Pristine, Ion-treated and Tungsten Nanoparticle-decorated p-type Silicon Tips}, series = {Physica Status Solidi B}, volume = {256}, journal = {Physica Status Solidi B}, number = {9}, publisher = {Wiley}, doi = {10.1002/pssb.201800646}, abstract = {The field electron emission characteristics of individual tips of a silicon field emitter array are analyzed. The array of conical-shaped tips is fabricated on a p-type silicon wafer by using reactive ion etching and sharpening oxidation. The tips are decorated with single tungsten nanoparticles at their apexes. Furthermore, the focused ion beam is also used to increase surface conductivity of some of the tips. Comparative measurements of field emission are performed by using the scanning anode probe field emission microscopy technique. All types of tips demonstrated emission activation consisting of a sudden current increase at a certain value of the applied voltage. Compared to the pristine tips, a noticeable reduction of the saturation effect in the current-voltage characteristics and a smaller light sensitivity for the decorated tips is found. For ion-treated tips, saturation effects and light sensitivity are completely suppressed. Scanning electron microscopy observations reveal the formation of single nanoscale protrusions extending from the metal particles and from the apexes of bare ion-treated tips after exposure under strong electric fields during the field emission measurements. The influence of protrusions growth on characteristics of silicon field emitter arrays is discussed.}, language = {en} } @article{MingelsPorshynPrommesbergeretal., author = {Mingels, Stephan and Porshyn, Vitali and Prommesberger, Christian and Langer, Christoph and Schreiner, Rupert and L{\"u}tzenkirchen-Hecht, Dirk and M{\"u}ller, G{\"u}nter}, title = {Photosensitivity of p-type black Si field emitter arrays}, series = {Journal of Applied Physics}, volume = {119}, journal = {Journal of Applied Physics}, number = {16}, doi = {10.1063/1.4948328}, abstract = {We have investigated the properties of black Si field emitter arrays under strong electric fields and laser illumination. A low onset field of 1.8 MV/m for an emission current of 1 nA was obtained. A pronounced saturation region of the dark and photo-enhanced current was observed, which provided a short-term stability of 0.1\% at 0.4 μA and 0.7\% at 1.0 μA, respectively. As maximum value for the photosensitivity, an on-off current switching ratio of 43 reaching about 13 μA was achieved at a laser power of 15 mW. Electron spectra in the dark and under laser illumination are presented, showing a current and light-sensitive voltage drop across the emitters as well as hints for hot electron emission.}, language = {en} } @article{PirkerŁawrowskiSchreineretal., author = {Pirker, Luka and Ławrowski, Robert Damian and Schreiner, Rupert and Remškar, Maja and Višić, Bojana}, title = {MoₓWₓ₋₁S₂ Nanotubes for Advanced Field Emission Application}, series = {Advanced Functional Materials}, journal = {Advanced Functional Materials}, publisher = {Wiley}, issn = {1616-3028}, doi = {10.1002/adfm.202213869}, pages = {1 -- 8}, abstract = {Transition metal dichalcogenide (TMDC) nanotubes complement the field of low-dimensional materials with their quasi-1D morphology and a wide set of intriguing properties. By introducing different transition metals into the crystal structure, their properties can be tailored for specific purpose and applications. Herein, the characterization and a subsequent preparation of single-nanotube field emission devices of MoxWx-1S2 nanotubes prepared via the chemical vapor transport reaction is presented. Energy-dispersive X-ray spectroscopy, Raman spectroscopy, and X-ray diffraction indicate that the molybdenum and tungsten atoms are randomly distributed within the crystal structure and that the material is highly crystalline. High resolution transmission electron microscopy and electron diffraction (ED) patterns further corroborate these findings. A detailed analysis of the ED patterns from an eight-layer nanotube reveal that the nanotubes grow in the 2H structure, with each shell consists of one bilayer. The work function of the nanotubes is comparable to that of pure MoS2 and lower of pure WS2 NTs, making them ideal candidates for field emission applications. Two devices with different geometrical setup are prepared and tested as field emitters, showing promising results for single nanotube field emission applications.}, language = {en} } @article{SchelsHerdlHausladenetal., author = {Schels, Andreas and Herdl, Florian and Hausladen, Matthias and Wohlfartsst{\"a}tter, Dominik and Edler, Simon and Bachmann, Michael and Pahlke, Andreas and Schreiner, Rupert and Hansch, Walter}, title = {Quantitative Field Emission Imaging for Studying the Doping-Dependent Emission Behavior of Silicon Field Emitter Arrays}, series = {Micromachines}, volume = {14}, journal = {Micromachines}, number = {11}, publisher = {MDPI}, doi = {10.3390/mi14112008}, abstract = {Field emitter arrays (FEAs) are a promising component for novel vacuum micro- and nanoelectronic devices, such as microwave power amplifiers or fast-switching X-ray sources. However, the interrelated mechanisms responsible for FEA degradation and failure are not fully understood. Therefore, we present a measurement method for quantitative observation of individual emission sites during integral operation using a low-cost, commercially available CMOS imaging sensor. The emission and degradation behavior of three differently doped FEAs is investigated in current-regulated operation. The measurements reveal that the limited current of the p-doped emitters leads to an activation of up to 55\% of the individual tips in the array, while the activation of the n-type FEA stopped at around 30\%. This enhanced activation results in a more continuous and uniform current distribution for the p-type FEA. An analysis of the individual emitter characteristics before and after a constant current measurement provides novel perspectives on degradation behavior. A burn-in process that trims the emitting tips to an integral current-specific ideal field enhancement factor is observed. In this process, blunt tips are sharpened while sharp tips are dulled, resulting in homogenization within the FEA. The methodology is described in detail, making it easily adaptable for other groups to apply in the further development of promising FEAs.}, language = {en} } @article{BachmannDuesbergPahlkeetal., author = {Bachmann, Michael and D{\"u}sberg, Felix and Pahlke, Andreas and Edler, Simon and Schels, Andreas and Herdl, Florian and Hausladen, Matthias and Buchner, Philipp and Schreiner, Rupert}, title = {The "LED-version" of the electron gun: An electron source for operation in ambient pressure environments based on silicon field emitter arrays}, series = {Vakuum in Forschung und Praxis}, volume = {35}, journal = {Vakuum in Forschung und Praxis}, number = {3}, publisher = {Wiley}, doi = {10.1002/vipr.202300801}, pages = {32 -- 37}, abstract = {We report on our progress to develop and optimize electron sources for practical applications. A simple fabrication process is introduced based on a wafer dicing saw and a wet chemical etch step without the need for a clean room. Due to the formation of crystal facets the samples show a homogeneous geometry throughout the array. Characterization techniques are developed to systematically compare various arrays. A very defined measurement procedure based on current controlled IV-sweeps as well as lifetime measurements at various currents is proposed. To investigate the current distribution in the array a commercial CMOS detector is used and shows the potential for in depth analysis of the arrays. Finally, a compact hermetically sealed housing is presented enabling electron generation in atmospheric pressure environments.}, language = {en} } @article{HausladenSchelsBuchneretal., author = {Hausladen, Matthias and Schels, Andreas and Buchner, Philipp and Bartl, Mathias and Asgharzade, Ali and Edler, Simon and Wohlfartsst{\"a}tter, Dominik and Bachmann, Michael and Schreiner, Rupert}, title = {Measurement of field emission array current distributions by metal-coated CMOS image sensors}, series = {Journal of Vacuum Science \& Technology B}, volume = {42}, journal = {Journal of Vacuum Science \& Technology B}, number = {6}, publisher = {AIP Publishing}, doi = {10.1116/6.0004074}, abstract = {A CMOS image sensor is utilized to determine the time- and spatially resolved distribution of the total electron emission current of a silicon field emission array. The sensor measures electron emission without the need for phosphorus screens or scintillators as converters. However, in initial experiments, rather low field emission currents of several hundreds of nanoamperes per emitter already damaged the sensor surface, which altered the systems' signal response over the measurement time. In consequence, we coated the CMOS sensor surface with a Cu layer for surface protection. In contrast to the original insulating surface, Cu is an excellent current- and heat-conductor, which avoids lens charging by providing a conductive path for incident electrons and has an improved heat dissipation capability. Measurements using a segmented field emission cathode with four individually addressable tips demonstrate a consistent correlation between the emission current and the sensor signal of the metal-coated image sensor. Furthermore, the characterization of a field emission array showed that single tip emission currents of up to 12 μA per tip are measurable without discernible damage effects of the sensor's surface.}, language = {en} } @article{SchreinerWiedmannCoenningetal., author = {Schreiner, Rupert and Wiedmann, J. and Coenning, W. and Porsche, J. and Gentner, Jean-Louis and Berroth, Manfred and Scholz, Ferdinand and Schweizer, H.}, title = {Fabrication approach for antiphase narrow linewidth complex coupled 1.55 μm DFB lasers}, series = {Electronics Letters}, volume = {35}, journal = {Electronics Letters}, number = {2}, publisher = {The Institution of Engineering and Technology IET}, issn = {0013-5194}, doi = {10.1049/el:19990132}, pages = {146 -- 148}, abstract = {A new method for fabricating narrow linewidth antiphase complex coupled MQW DFB lasers by periodically etching the active layer and quartemary InGaAsP overgrowth is reported. The minimum linewidth for a 375 µm long ridge waveguide laser is only 250 kHz at an optical output power of 4 mW.}, language = {en} } @article{HausladenSchelsAsgharzadeetal., author = {Hausladen, Matthias and Schels, Andreas and Asgharzade, Ali and Buchner, Philipp and Bartl, Mathias and Wohlfartsst{\"a}tter, Dominik and Edler, Simon and Bachmann, Michael and Schreiner, Rupert}, title = {Investigation of Influencing Factors on the Measurement Signal of a CMOS Image Sensor for Measuring Field Emission Currents}, series = {Sensors}, volume = {25}, journal = {Sensors}, number = {5}, publisher = {MDPI}, doi = {10.3390/s25051529}, pages = {17}, language = {en} } @article{EilerWeberGerlesbergeretal., author = {Eiler, Julian and Weber, Stefan and Gerlesberger, Peter and Pl{\"o}chinger, Heinz and Schreiner, Rupert}, title = {Active heat-loss compensated miniaturized pirani sensor chip}, series = {IEEE Sensors Letters}, volume = {9}, journal = {IEEE Sensors Letters}, number = {10}, publisher = {Institute of Electrical and Electronics Engineers (IEEE)}, issn = {2475-1472}, doi = {10.1109/LSENS.2025.3605747}, pages = {4}, abstract = {Due to the limited measuring range of commercial Pirani sensors in lower pressure regimes, attempts are being made to extend the measuring range of the sensors. Our approach to extend the measuring range toward lower pressures is a micro-electromechanical systems (MEMS) Pirani sensor with active heat compensation on the suspensions. The sensor element has the shape of a microhotplate and consists of a nickel heating meander embedded in two silicon nitride layers. The whole structure is built on a silicon wafer. The sensor element is suspended on all four corners of the substrate. On each of the suspensions, there is an additional heating structure that minimizes the heat flux from the hot sensor element toward the substrate. The sensor is driven at a constant temperature through a self-balancing Wheatstone bridge. A constant voltage is applied to the heating structures on the suspensions. It has been demonstrated that with these additional heaters, the sensitivity of the sensor can be increased in the high-vacuum regime. This enables reliable vacuum measurements down to 10-6 mbar.}, language = {en} } @article{BuchnerHausladenBartletal., author = {Buchner, Philipp and Hausladen, Matthias and Bartl, Mathias and Bachmann, Michael and Schreiner, Rupert}, title = {High current field emission from Si nanowires on pillar structures}, series = {Journal of Vacuum Science and Technology B: Nanotechnology and Microelectronics}, volume = {42}, journal = {Journal of Vacuum Science and Technology B: Nanotechnology and Microelectronics}, number = {2}, publisher = {AIP}, issn = {2166-2754}, doi = {10.1116/6.0003384}, abstract = {We investigate the influence of the geometry and doping level on the performance of n-type silicon nanowire field emitters on silicon pillar structures. Therefore, multiple cathodes with 50 by 50 pillar arrays (diameter: 5 μm, height: 30 μm, spacing: 50 μm) were fabricated and measured in diode configuration. In the first experiment, we compared two geometry types using the same material. Geometry 1 is black silicon, which is a highly dense surface covering a forest of tightly spaced silicon needles resulting from self-masking during a plasma etching process of single crystal silicon. Geometry 2 are silicon nanowires, which are individual spaced-out nanowires in a crownlike shape resulting from a plasma etching process of single crystal silicon. In the second experiment, we compared two different silicon doping levels [n-type (P), 1-10 and <0.005 Ω cm] for the same geometry. The best performance was achieved with lower doped silicon nanowire samples, emitting 2 mA at an extraction voltage of 1 kV. The geometry/material combination with the best performance was used to assemble an integrated electron source. These electron sources were measured in a triode configuration and reached onset voltages of about 125 V and emission currents of 2.5 mA at extraction voltages of 400 V, while achieving electron transmission rates as high as 85.0\%.}, language = {en} } @article{TanSchreinerHausladenetal., author = {Tan, Jing Jie and Schreiner, Rupert and Hausladen, Matthias and Asgharzade, Ali and Edler, Simon and Bartsch, Julian and Bachmann, Michael and Schels, Andreas and Kwan, Ban-Hoe and Ng, Danny Wee-Kiat and Hum, Yan-Chai}, title = {SiMiC: Context-aware silicon microstructure characterization using attention-based convolutional neural networks for field-emission tip analysis}, series = {Journal of Vacuum Science \& Technology B}, volume = {43}, journal = {Journal of Vacuum Science \& Technology B}, number = {6}, publisher = {AVS}, doi = {10.1116/6.0005068}, abstract = {Accurate characterization of silicon microstructures is essential for advancing microscale fabrication, quality control, and device performance. Traditional analysis using scanning electron microscopy (SEM) often requires labor-intensive, manual evaluation of feature geometry, limiting throughput and reproducibility. In this study, we propose SiMiC: Context-aware Silicon Microstructure Characterization Using Attention-based Convolutional Neural Networks for Field-Emission Tip Analysis. By leveraging deep learning, our approach efficiently extracts morphological features—such as size, shape, and apex curvature—from SEM images, significantly reducing human intervention while improving measurement consistency. A specialized dataset of silicon-based field-emitter tips was developed, and a customized convolutional neural network architecture incorporating attention mechanisms was trained for multiclass microstructure classification and dimensional prediction. Comparative analysis with classical image processing techniques demonstrates that SiMiC achieves high accuracy while maintaining interpretability. The proposed framework establishes a foundation for data-driven microstructure analysis directly linked to field-emission performance, opening avenues for correlating emitter geometry with emission behavior and guiding the design of optimized cold-cathode and SEM electron sources. The related dataset and algorithm repository that could serve as a baseline in this area can be found at https://research.jingjietan.com/?q=SIMIC.}, language = {en} }