@inproceedings{OttawaRomanoEhrlichetal., author = {Ottawa, Patrycja and Romano, Marco and Ehrlich, Ingo and Wagner, Marcus and Gebbeken, Norbert}, title = {The influence of ondulation in fabric reinforced composites on dynamic properties in a mesoscopic scale}, series = {11. LS-DYNA Forum, 9. - 10. Oktober 2012, Ulm}, booktitle = {11. LS-DYNA Forum, 9. - 10. Oktober 2012, Ulm}, pages = {171 -- 172}, abstract = {Structural mechanic properties of fiber reinforced plastics depend on the single components' properties, namely matrix and fiber [5]. Simple micromechanic homogenization theories reach a limit when a laminate consists of fabric reinforced layers instead of unidirectional layers. The ondulations of warp and fill yarn caused by the textile semi-finished product are the reason why the mesoscopic scale, which is in between the microscopic and the macroscopic scale, has to be taken into account when mechanically characterizing fabric reinforced composites [3]. In this scale a mesomechanic kinematic can be derived analytically. Especially, when considering free damped vibrations of structures the repeated acting of the kinematic correlation significantly affects the damping behaviour to higher values compared to theoretically predicted damping ratios. The model is investigated using Finite-Element-Analyses and basically validated experimentally.}, language = {en} } @phdthesis{Romano, author = {Romano, Marco}, title = {Charakterisierung von gewebeverst{\"a}rkten Einzellagen aus kohlenstofffaserverst{\"a}rktem Kunststoff (CFK) mit Hilfe einer mesomechanischen Kinematik sowie strukturdynamischen Versuchen}, publisher = {Shaker}, address = {Aachen}, isbn = {978-3-8440-5177-3}, doi = {10.2370/9783844051773}, pages = {254}, abstract = {Die vorliegende Arbeit behandelt die analytische und numerische Identifikation einer mesomechanischen Kinematik in gewebeverst{\"a}rkten Einzellagen sowie deren Validierung {\"u}ber die Strukturdynamik von flachen stabf{\"o}rmigen Probek{\"o}rpern aus kohlenstofffaserverst{\"a}rktem Kunststoff (CFK). Unter der Voraussetzung, dass das wiederholte Wirken der Kinematik Energie dissipiert, tr{\"a}gt sie bei zyklischer viskoelastischer Deformation zus{\"a}tzlich zur reinen viskoelastischen Werkstoffd{\"a}mpfung in gewebeverst{\"a}rkten Einzellagen bei. Die analytischen und numerischen Untersuchungen beschr{\"a}nken sich auf die Betrachtung des ebenen, zweidimensionalen Zusammenhangs einer vollst{\"a}ndigen Ondulation bzw. einer repr{\"a}sentativen Sequenz in Dickenrichtung. Zur Parameteridentifikation werden die geometrischen Abmessungen in definierten Schritten variiert. Daf{\"u}r wird der Grad der Ondulation in gewebeverst{\"a}rkten Einzellagen {\~O}=A/L als dimensionslose Kennzahl eingef{\"u}hrt. Zur Validierung der d{\"a}mpfungserh{\"o}henden Wirkung der in den analytischen und numerischen Untersuchung identifizierten mesomechanischen Kinematik in gewebeverst{\"a}rkten Einzellagen werden in experimentellen strukturdynamischen Untersuchungen frei abklingende Transversalschwingungen von einseitig fest eingespannten Probek{\"o}rpern untersucht. Im Detail werden flache stabf{\"o}rmige Probek{\"o}rper aus kohlenstofffaserverst{\"a}rktem Epoxidharz mit Lagenaufbauten aus 0°-unidirektionalen und gewebeverst{\"a}rkten Einzellagen untersucht. Die Ergebnisse der experimentellen strukturdynamischen Untersuchungen dienen schließlich der Validierung des analytischen Modells und der numerischen Berechnungen. Die d{\"a}mpfungserh{\"o}hende Wirkung der identifizierten mesomechanischen Kinematik wird schließlich in Abh{\"a}ngigkeit des eingef{\"u}hrten Grades der Ondulation {\~O} quantifiziert.}, language = {de} } @article{BohmannSchlampEhrlich, author = {Bohmann, T. and Schlamp, Matthias and Ehrlich, Ingo}, title = {Acoustic emission of material damages in glass fibre-reinforced plastics}, series = {Composites Part B: Engineering}, volume = {155}, journal = {Composites Part B: Engineering}, number = {December}, publisher = {Elsevier}, doi = {10.1016/j.compositesb.2018.09.018}, pages = {444 -- 451}, abstract = {The aim of this study is to compare two different standardized testing procedures, tensile testing and Mode-I double cantilever beam (DCB) testing, to evaluate a possible correlation between the dominant failure in glass fibre-reinforced plastics and their according acoustic emissions (AE). AE is processed by using a burst collection of all recorded transient signals and is further analysed with the k-means clustering algorithm. To generate damage related AE, a series of experiments for tensile testing and Mode-I DCB testing is performed on 16-layer glass fibre/epoxy specimens with a cross-ply lay-up for tensile and an unidirectional lay-up for Mode-I DCB testing. Three sensors at tensile testing and one sensor at Mode-I DCB testing gather AE data. The results of clustered burst signals show a good accordance between both testing procedures, with a similar weighted peak frequency (WPF) range in each classified cluster. In total, three different clusters are determined. An assignment of these three clusters to the three dominant damage mechanisms, visually observed by microscopy, is suggested.}, language = {en} } @techreport{ValentinoRomanoEhrlichetal., author = {Valentino, Piergiorgio and Romano, Marco and Ehrlich, Ingo and Furgiuele, Franco and Gebbeken, Norbert}, title = {Mechanische Charakterisierung von basaltfaser-verst{\"a}rkten Kunststoffen mit Gewebeverst{\"a}rkung - Numerische und experimentelle Untersuchungen}, series = {Forschungsbericht 2013}, journal = {Forschungsbericht 2013}, publisher = {inixmedia GmbH Marketing \& Medienberatung}, organization = {Ostbayerische Technische Hochschule Regensburg}, language = {de} } @inproceedings{Afanasev, author = {Afanasev, Anna}, title = {Force-oriented 3D printing of continuous fiber-reinforced plastic structures}, series = {Applied Research Conference 2019 - ARC 2019, 08 July 2019, Regensburg}, booktitle = {Applied Research Conference 2019 - ARC 2019, 08 July 2019, Regensburg}, editor = {Mottok, J{\"u}rgen and Reichenberger, Marcus}, publisher = {Pro Business GmbH}, address = {Berlin}, isbn = {978-3-96409-182-6}, pages = {213 -- 218}, subject = {Faserverbundwerkstoff}, language = {en} } @inproceedings{BaumerKastenmeierEhrlich, author = {Baumer, A. and Kastenmeier, Andreas and Ehrlich, Ingo}, title = {Investigation of Bolted Composite Joints with Different Reinforcement Elements at the Bolt Hole}, series = {4th Applied Research Conference, 5th July 2014, Ingolstadt}, booktitle = {4th Applied Research Conference, 5th July 2014, Ingolstadt}, editor = {Ziemann, Olaf and Mottok, J{\"u}rgen and Pforr, Johannes}, publisher = {Shaker}, pages = {255 -- 258}, language = {en} } @inproceedings{FritzSchmidEhrlich, author = {Fritz, B. and Schmid, Vinzent and Ehrlich, Ingo}, title = {Analytical and numerical shear stress analysis of adhesive structural bonded joints under tension load}, series = {Applied Research Conference 2014 - ARC 2014, 5th July 2014, Ingolstadt}, booktitle = {Applied Research Conference 2014 - ARC 2014, 5th July 2014, Ingolstadt}, editor = {Ziemann, Olaf and Mottok, J{\"u}rgen and Pforr, Johannes}, publisher = {Shaker}, address = {Aachen}, pages = {266 -- 271}, language = {de} } @inproceedings{BaumerKastenmeierEhrlich, author = {Baumer, A. and Kastenmeier, Andreas and Ehrlich, Ingo}, title = {A Numerical Study of Reinforced Bolted Composite Joints}, series = {Applied Research Conference 2015: ARC 2015 - N{\"u}rnberg, 3rd July 2015}, booktitle = {Applied Research Conference 2015: ARC 2015 - N{\"u}rnberg, 3rd July 2015}, editor = {Mottok, J{\"u}rgen and Reichenberger, Marcus and Scharfenberg, J. and Ziemann, Olaf}, publisher = {Book-on-demand-Verlag}, pages = {278 -- 282}, language = {en} } @inproceedings{WaetzigSchmidEhrlich, author = {W{\"a}tzig, A. and Schmid, Vinzent and Ehrlich, Ingo}, title = {Damage Modelling of Adhesive Joints Using the Cohesive Zone Model}, series = {Applied Research Conference 2016 - ARC 2016, Augsburg, 24 June 2016}, booktitle = {Applied Research Conference 2016 - ARC 2016, Augsburg, 24 June 2016}, editor = {Mottok, J{\"u}rgen and Reichenberger, Marcus and Stolle, Reinhard}, publisher = {Pro Business Verlag}, address = {Berlin}, language = {en} } @inproceedings{DinnebierEhrlich, author = {Dinnebier, Heinrich and Ehrlich, Ingo}, title = {The Effects of Severe Temperature Changes and High Humidity on Porous CFRP}, series = {Proceedings of the 15th International Materials Symposium (IMSP´2014), Pamukkale University (Denizli, Turkey), 15./17. October 2014}, booktitle = {Proceedings of the 15th International Materials Symposium (IMSP´2014), Pamukkale University (Denizli, Turkey), 15./17. October 2014}, editor = {Meran, C.}, pages = {433 -- 440}, abstract = {Purpose: A route to manufacture porous carbon fiber reinforced plastic (CFRP) for study purposes is described. Design/methodology/approach: The porous CFRP is characterized using standard techniques such as matrix digestion as well as the more sophisticated method of high resolution Microfocus X-Ray Tomography (μCT). A comparison of the results of those methods is presented. The mass gains of specimens with a wide range of porosity have been measured both in constant humidity and in alternating environments. Findings: It could be shown that severe temperature changes can temporarily increase the moisture content of porous CFRP. However, after the return to a constant environment, the moisture content returns back to saturation levels. Furthermore, it could be shown by X-Ray Tomography that even under severe climatic conditions no permanent liquid water condensates inside the pores. Research limitations/implications: Using Microfocus Computed Tomography it could be shown that even after nearly a year under hot-wet conditions and more than 150 severe temperature cycles there is no liquid water detectable inside the pores. Originality/value: In this paper the effects of severe temperature changes and high humidity on porous CFRP.}, language = {en} } @inproceedings{EhrlichDinnebierJost, author = {Ehrlich, Ingo and Dinnebier, Heinrich and Jost, C.}, title = {Comparison of Impact Delaminations in CFRP Using Ultrasonic Testing, Microfocus Computed X-Ray Tomography and Micrographic Cross-Section}, series = {Proceeding of the 15th International Materials Symposium (IMSP´2014), Pamukkale University (Denizli, Turkey), 15./17. October 2014}, booktitle = {Proceeding of the 15th International Materials Symposium (IMSP´2014), Pamukkale University (Denizli, Turkey), 15./17. October 2014}, editor = {Meran, C.}, pages = {441 -- 450}, language = {en} } @inproceedings{Wenzl, author = {Wenzl, C.}, title = {Comparison of Analytical and Numerical Results for the Deformation of Circular Curved Structures under Pressure Load}, series = {Applied Research Conference 2018 - ARC 2018, 10 July 2018 Deggendorf}, booktitle = {Applied Research Conference 2018 - ARC 2018, 10 July 2018 Deggendorf}, editor = {Mottok, J{\"u}rgen and Reichenberger, Marcus and Bogner, Werner}, publisher = {Pro Business GmbH}, address = {Berlin}, isbn = {978-3-96409-018-8}, pages = {150 -- 155}, language = {en} } @inproceedings{FaberKastenmeierEhrlich, author = {Faber, M. and Kastenmeier, Andreas and Ehrlich, Ingo}, title = {Three-dimensional finite element analysis of a composite tube with multi-row bolted joints}, series = {Applied Research Conference 2016 - ARC 2016, Augsburg, 24 June 2016}, booktitle = {Applied Research Conference 2016 - ARC 2016, Augsburg, 24 June 2016}, editor = {Mottok, J{\"u}rgen and Reichenberger, Marcus and Stolle, Reinhard}, publisher = {Pro Business Verlag}, address = {Berlin}, language = {de} } @inproceedings{Gebhardt, author = {Gebhardt, Jakob}, title = {Low Velocity Impact of GFRP Laminate - Experimental Observations and Numerical Modelling}, series = {Applied Research Conference 2018 - ARC 2018, 10 July 2018 Deggendorf}, booktitle = {Applied Research Conference 2018 - ARC 2018, 10 July 2018 Deggendorf}, editor = {Mottok, J{\"u}rgen and Reichenberger, Marcus and Bogner, Werner}, publisher = {Pro Business GmbH}, address = {Berlin}, isbn = {978-3-96409-018-8}, pages = {211 -- 215}, language = {en} } @inproceedings{IbanezGomezKastenmeierEhrlich, author = {Ibanez Gomez, D. and Kastenmeier, Andreas and Ehrlich, Ingo}, title = {Development and construction of a winding machine for the production of composite tubes}, series = {4th Applied Research Conference - ARC 2014, 5th July 2014, Ingolstadt}, booktitle = {4th Applied Research Conference - ARC 2014, 5th July 2014, Ingolstadt}, editor = {Ziemann, Olaf and Mottok, J{\"u}rgen and Pforr, Johannes}, publisher = {Shaker}, address = {Aachen}, pages = {315 -- 318}, language = {en} } @inproceedings{BrulandSchmidEhrlich, author = {Bruland, Matthias and Schmid, Vinzent and Ehrlich, Ingo}, title = {Analyzing and Testing of a Single Solution of Self-cutting Thread Inserts in Composites}, series = {Applied Research Conference 2014 - ARC 2014, 5th July 2014, Ingolstadt}, booktitle = {Applied Research Conference 2014 - ARC 2014, 5th July 2014, Ingolstadt}, editor = {Ziemann, Olaf and Mottok, J{\"u}rgen and Pforr, Johannes}, publisher = {Shaker}, pages = {286 -- 288}, language = {en} } @article{SchimmerLadewigMotschetal., author = {Schimmer, Florian and Ladewig, Sven and Motsch, Nicole and Hausmann, Joachim M. and Ehrlich, Ingo}, title = {Comparison of Low-Velocity Impact Damage Behavior of Unidirectional Carbon Fiber-Reinforced Thermoset and Thermoplastic Composites}, series = {Key Engineering Materials}, volume = {809}, journal = {Key Engineering Materials}, publisher = {Trans Tech Publications}, issn = {1662-9795}, doi = {10.4028/www.scientific.net/KEM.809.9}, pages = {9 -- 14}, abstract = {This paper investigates the damage behavior of thermoset and thermoplastic fiber-reinforced composites. The specimens were subjected to low-velocity impacts (LVI) to produce barely visible impact damages (BVID). To compare the dependency of the matrix system and the laminate lay-up on the impact damage, four test series were set up. Therefore, laminates with an epoxy (EP) and a polyether ether ketone (PEEK) matrix in a quasi-isotropic (QI) [+45/0/-45/90]2s and an orthotropic (OT) fiber lay-up [0/90]4s were manufactured. To eliminate the influence of variant fiber systems, the thermoplastic tape and the thermoset prepreg contain similar carbon fibers (CF). After impact testing with three different impact energies, inner damages were investigated by using ultrasonic analyses. To get a deeper understanding of the interior damage mechanisms, cross sections of the damaged areas were examined via reflected light microscopy. By using these destructive and non-destructive test methods, significant differences in the damage behavior of composites with thermoplastic and thermoset matrix systems were identified for both laminate lay-ups.}, language = {en} } @inproceedings{SieglRiegerKovariketal., author = {Siegl, Marco and Rieger, David and Kov{\´a}r{\´i}k, Tom{\´a}š and Ehrlich, Ingo}, title = {Long-Term Behavior of Thermoplastics under UV Light tested by a self-build Device}, series = {3. OTH-Clusterkonferenz, 13. April 2018, Weiden, Tagungsband; Festschrift, 5 Jahre OTH-Verbund}, booktitle = {3. OTH-Clusterkonferenz, 13. April 2018, Weiden, Tagungsband; Festschrift, 5 Jahre OTH-Verbund}, organization = {Ostbayerische Technische Hochschule}, pages = {118 -- 122}, abstract = {This article presents first results of artificial aging experi-ments by ultraviolet (UV) irradiation on thermoplasticmaterials conducted as an intent of the research project Thermoplastic Composite Structures (TheCoS) in colla-boration of the Ostbayerische Technische Hochschule(OTH) Regensburg and the University of West Bohemia(UWB) in Pilsen as part of a cross-border cooperation. In technical applications, thermoplastic materials are oftenaffected by aging and a related deterioration of the mechanical properties. Therefore, it is necessary to identifythe aging behavior of thermoplastic materials. For this,experiments were performed for three thermoplasticmaterials, namely polypropylene (PP), ultra high mole -cular weight polyethylene (UHMWPE) and high impactstrength polystyrene (HIPS). For these experiments, a UV chamber was constructed according to the internationalstandard EN ISO 4892-3 for simulation of exposurebehind window glass. The results are evaluated by testing the flexural strength and the dynamic mechanicalresponse after a selected period of time under UV lightand then compared to untreated test specimens.}, language = {en} } @inproceedings{ValentinoRomanoEhrlichetal., author = {Valentino, Piergiorgio and Romano, Marco and Ehrlich, Ingo and Furgiuele, Franco and Gebbeken, Norbert}, title = {Mechanical characterization of basalt fibre reinforced plastic with different fabric reinforcements - Tensile tests and FE-calculations with representative volume elements (RVEs)}, series = {Acta Fracturae - XXll Convegno Nazionale IGF (Italiano Gruppo Frattura)}, booktitle = {Acta Fracturae - XXll Convegno Nazionale IGF (Italiano Gruppo Frattura)}, editor = {Iacovello, F. and Risitano, G. and Susmel, L.}, abstract = {This paper describes the results of tensile tests and finite element (FE) calculations with representative volume elements (RVEs) of basalt fibre reinforced plastic with two different types of fabric reinforcements. As fabric reinforcements show repeating ondulations of warp and fill yarn, simple mixtures laws reach their limits. That is the reason why the mesoscopic dimension, lying between the microscopic and the macroscopic dimension, has to be taken into account when a mechanical characterization of fabric reinforced composites is carried out. The aim of this work is to determine the stiffness of a fabric reinforced composite in warp and fill direction with numerical investigations. The simulations are based on FE-calculation with two different RVEs. The tensile tests and the FE-calculations have been carried out for two different types of basalt fabrics, namely twill 2/2 and twill 1/3. The comparison between the experimental data and the results of the FE-calculations are provided in order to support the validity of the proposed model.}, language = {en} } @inproceedings{Seppenhauser, author = {Seppenhauser, P.}, title = {Examinations of the Printer Head Prototype for UV Resins with Continous Fiber-Reinforcement}, series = {Applied Research Conference 2019 - ARC 2019, 8 July 2019, Regensburg}, booktitle = {Applied Research Conference 2019 - ARC 2019, 8 July 2019, Regensburg}, editor = {Mottok, J{\"u}rgen and Reichenberger, Marcus}, publisher = {Pro Business GmbH}, address = {Berlin}, isbn = {978-3-96409-182-6}, pages = {241 -- 248}, subject = {3D-Druck}, language = {en} }