@inproceedings{BerndtLindnerTschurtschenthaleretal., author = {Berndt, Dominik and Lindner, Matthias and Tschurtschenthaler, Karl and Langer, Christoph and Schreiner, Rupert}, title = {Miniaturized Plasma Actuator Flow Measurements by MEMS-Based Thermal Conductivity Sensors}, series = {MDPI Proceedings of Eurosensors 2018, 9-12 September, Graz}, volume = {Vol.13}, booktitle = {MDPI Proceedings of Eurosensors 2018, 9-12 September, Graz}, number = {2}, doi = {10.3390/proceedings2130939}, abstract = {The gasflow created by a minaturized dielectric barrier discharge (DBD) plasma actuator is measured by a MEMS-based thermal conductivity gas sensor giving an indication of flow velocity and flow direction. The possiblity of several sensors in a small area gives a far better accuracy of local flow phenomena compared to conventional sensors. This is important for a better understanding of plasma- induced flow characteristics.}, language = {en} } @incollection{FrommeldWeber, author = {Frommeld, Debora and Weber, Karsten}, title = {Aufkl{\"a}rung, Risiko, Datennutzung: Ergebnisse einer MEESTAR-Befragung zu Telepr{\"a}senzrobotern}, series = {Digitale Technik f{\"u}r ambulante Pflege und Therapie III - Nutzung Akzeptanz Wirkung und Lebensqualit{\"a}t}, booktitle = {Digitale Technik f{\"u}r ambulante Pflege und Therapie III - Nutzung Akzeptanz Wirkung und Lebensqualit{\"a}t}, editor = {Weber, Karsten and Haug, Sonja and Lauer, Norina and Mohr, Christa}, publisher = {transcript}, address = {Bielefeld}, isbn = {978-3-8376-6728-8}, doi = {10.14361/9783839467282-011}, pages = {241 -- 272}, language = {de} } @incollection{FrommeldWeber, author = {Frommeld, Debora and Weber, Karsten}, title = {Telepr{\"a}senzroboter zur Unterst{\"u}tzung von Pflege und Therapie}, series = {Digitale Technik f{\"u}r ambulante Pflege und Therapie III: Nutzung Akzeptanz Wirkung und Lebensqualit{\"a}t}, booktitle = {Digitale Technik f{\"u}r ambulante Pflege und Therapie III: Nutzung Akzeptanz Wirkung und Lebensqualit{\"a}t}, editor = {Weber, Karsten and Haug, Sonja and Lauer, Norina and Mohr, Christa}, publisher = {transcript}, address = {Bielefeld}, isbn = {978-3-8376-6728-8}, doi = {10.14361/9783839467282-013}, pages = {307 -- 328}, language = {de} } @article{HellwigSchrollDecker, author = {Hellwig, Michael and Schroll-Decker, Irmgard}, title = {Wirksamkeit wissenschaftlicher Weiterbildung aus Sicht von Stakeholdern}, series = {ZHWB - Zeitschrift Hochschule und Weiterbildung}, journal = {ZHWB - Zeitschrift Hochschule und Weiterbildung}, number = {2}, doi = {10.4119/zhwb-2369}, pages = {22 -- 31}, abstract = {Die Weiterbildung an Hochschulen ist an evidenzbasierten Daten interessiert, um Aussagen {\"u}ber die Wirksamkeit von eigenen Angeboten treffen zu k{\"o}nnen. Oftmals unklar ist, was unter Wirksamkeit verstanden werden kann und welche Voraussetzungen gegeben sein m{\"u}ssen, damit die Weiterbildungen Wirkung entfalten. Der Beitrag stellt eine Studie vor, die beide Aspekte adressiert und Aussagen unterschiedlicher Beteiligter am Weiterbildungsgeschehen wiedergibt. Angebotsseitig wurden Weiterbildungsverantwortliche sowie Lehrpersonen der Hochschule befragt. Nachfrageseitig wurden Teilnehmende berufsbegleitender Studieng{\"a}nge und Unternehmensvertreter*innen aus ausgew{\"a}hlten Branchen einbezogen. Die erhobenen qualitativen Daten wurden inhaltsanalytisch analysiert und induktiv zu Kategorien zusammengefasst. Die Ergebnisse zeigen insgesamt f{\"u}nf Oberkategorien auf, die die Wirksamkeit abbilden: (1) Erfolgreicher Praxistransfer; (2) Erwerb von Kenntnissen, F{\"a}higkeiten und Kompetenzen; (3) Strategischer Nutzen; (4) Sozialer/kultureller Nutzen und (5) Resonanz der Teilnehmenden auf die wissenschaftliche Weiterbildung. Die Voraussetzungen lassen sich ebenfalls in f{\"u}nf Kategorien abbilden: (a) teilnehmenden-, (b) unternehmens-, (c) angebots-, (d) hochschul- und (e) markt-/umfeldbezogene Faktoren. Im Beitrag werden nach der Darstellung der Studienergebnisse Schlussfolgerungen f{\"u}r die Weiterbildungspraxis in Hinblick auf die Themen Evaluation, Theorie-Praxis-Transfer und Marketing/Zielgruppenspezifische Kommunikation diskutiert.}, subject = {Wissenschaftliche Weiterbildung}, language = {de} } @article{MaiwaldEnglmaierHierl, author = {Maiwald, Frederik and Englmaier, Stephan and Hierl, Stefan}, title = {Online pyrometry for weld seam localization in absorber-free laser transmission welding of transparent polymers}, series = {Journal of Laser Micro/Nanoengineering}, volume = {Vol. 16}, journal = {Journal of Laser Micro/Nanoengineering}, number = {1}, publisher = {Japan Laser Processing Society}, issn = {1880-0688}, doi = {10.2961/jlmn.2021.01.2002}, pages = {8 -- 13}, abstract = {Production of optical and medical devices makes high demands on cleanliness, precision, visual appearance and reliability. Advantages of laser transmission welding - contactless input of energy, high precision, no adhesives and no particle formation - can be fully exploited for this use. For absorber-free welding, lasers emitting in the polymers' intrinsic absorption spectrum between 1.6 μm and 2 μm are used. Focusing the laser beam with high NA provides large intensity gradients inside the specimen and enables selective fusing of the joining zone without affecting the surface. Since a molten upper surface leads to visible and palpable irregularities and causes warpage, the verticalexpansion of the weld seam is crucial. To meet the high quality and reliability required in the medical and optical industry, online monitoring of the seam is necessary. The aim of this work is the localization and evaluation of the weld seam using pyrometry. First, the emitted thermal radiation is computed, enabling signal analysis regarding origin and spectrum. Thus, assessment of measurement spectrum and forecast of the signal in dependence on seam shape and position is possible. Finally, welding tests with Topas 8007-04 are performed at 200 mm/s feed rate and monitored with 100 kHz. The comparison of tracked data with thin-cuts demonstrates that weld seam localization by pyrometry is possible, enabling online assessment of the process.}, subject = {Laserdurchstrahlschweissen}, language = {en} } @inproceedings{KaesbauerSchmailzlPrehmetal., author = {K{\"a}sbauer, Johannes and Schmailzl, Anton and Prehm, Jens and Loose, Tobias and Hierl, Stefan}, title = {Simulation of Quasi-Simultaneous Laser Transmission Welding of Plastics}, series = {Procedia CIRP}, volume = {94}, booktitle = {Procedia CIRP}, publisher = {Elsevier}, doi = {10.1016/j.procir.2020.09.136}, pages = {737 -- 741}, abstract = {Thermo-mechanical simulation offers great opportunities to optimize welding processes of plastics. For realistic simulation, the temperature dependent mechanical properties need to be implemented from ambient temperature to temperatures above the flow temperature. Standard test methods are insufficient for characterization in the entire temperature range because close to the flow temperature the material is too soft for tensile tests and too stiff for rheometry. Therefore, an optimization strategy is developed, that determines unknown material parameters by testing in welding simulations. The unknown parameters are iteratively adjusted to minimize the mismatch between computed and measured set-paths. Thus, important process characteristics are calculated realistically, enabling the computer aided assessment of the weld quality.}, subject = {Kunststoffschweißen}, language = {en} } @inproceedings{MaiwaldEnglmaierHierl, author = {Maiwald, Frederik and Englmaier, Stephan and Hierl, Stefan}, title = {Absorber-free Laser Transmission Welding of Transparent Polymers using Fixed Focus Optics and 3D Laser Scanner}, series = {Procedia CIRP}, volume = {94}, booktitle = {Procedia CIRP}, publisher = {Elsevier}, doi = {10.1016/j.procir.2020.09.117}, pages = {686 -- 690}, abstract = {Laser transmission welding is a well-known joining technology for thermoplastics, providing reliable and hermetical sealing without adhesives or particle formation. The main advantages of laser-based energy input - high precision, no additional adhesive and no particle emission - are essential for medical and optical applications. To obtain sufficient absorption in visually transparent polymers, thulium fibre lasers emitting in the polymers' intrinsic absorption spectrum are used. Optics with high numerical aperture provide large intensity gradients inside the specimen, enabling selective fusing in the joining zone. Although the basic feasibility has already been demonstrated, the welding process lacks stability and productivity. Aim of this work is the determination of optimized settings for a fast and reliable welding process. Thus, the interplay of process parameters as well as their impact on the seam are analysed by thermal simulations. Calculated settings are verified by welding tests with COC, PA6 and PETG, using a fixed-focus optics and a 3D laser scanner with up to 200 mm/s feed rate.}, language = {en} } @incollection{HaugVetter, author = {Haug, Sonja and Vetter, Miriam}, title = {{\"A}ltere Menschen im Wohnquartier Margaretenau in Regensburg - aktuelle Situation und zuk{\"u}nftiger Bedarf}, series = {Wohnen und Gesundheit im Alter}, booktitle = {Wohnen und Gesundheit im Alter}, editor = {Teti, Andrea}, publisher = {Springer VS}, address = {Wiesbaden}, isbn = {978-3-658-34385-9}, doi = {10.1007/978-3-658-34386-6_14}, pages = {215 -- 227}, abstract = {Der Beitrag zeigt Ergebnisse einer Begleitstudie zur Restaurierung und energetischen Modernisierung des historischen genossenschaftlichen Wohnquartiers Margaretenau in Regensburg im Projekt MAGGIE. Bei der Gestaltung von Wohnungen und Gelegenheiten f{\"u}r die soziale Einbettung im Quartier wird eine altersgerechte Perspektive eingenommen. Die Darstellung der schriftlichen standardisierten Haushaltsbefragung (n = 195) nimmt die Lebenssituation {\"a}lterer Menschen ab 65 Jahren in den Fokus. Dazu werden die Themenbereiche Haushaltsstruktur, altersgerechtes Wohnen und Gemeinschaftseinrichtungen pr{\"a}sentiert. Neben der aktuellen Wohnsituation wurden Pl{\"a}ne und W{\"u}nsche f{\"u}r das zuk{\"u}nftige Wohnen abgefragt. Im Alter schwindet die Bereitschaft f{\"u}r Ver{\"a}nderungen, was sich am Wunsch zum Altern in der bisherigen Wohnung und Verbleib im Wohnquartier zeigt. Das Interesse am barrierereduzierten Wohnen ist bei {\"a}lteren Haushalten geringer als bei j{\"u}ngeren. Es zeigt sich ein {\"u}berdurchschnittlich hohes Maß an lokalem Sozialkapital, wobei kein signifikanter Unterschied zwischen j{\"u}ngeren und {\"a}lteren Haushalten besteht.}, language = {de} } @incollection{Weber, author = {Weber, Karsten}, title = {Altersgerechte Assistenzsysteme. Ein {\"U}berblick}, series = {Gute Technik f{\"u}r ein gutes Leben im Alter? Akzeptanz, Chancen und Herausforderungen altersgerechter Assistenzsysteme}, booktitle = {Gute Technik f{\"u}r ein gutes Leben im Alter? Akzeptanz, Chancen und Herausforderungen altersgerechter Assistenzsysteme}, editor = {Frommeld, Debora and Scorna, Ulrike and Haug, Sonja and Weber, Karsten}, publisher = {transcript}, address = {Bielefeld}, isbn = {978-3-8376-5469-1}, doi = {10.1515/9783839454695-002}, pages = {27 -- 62}, subject = {Altenpflege}, language = {de} } @incollection{HaugScharf, author = {Haug, Sonja and Scharf, Anna}, title = {Berufsbegleitend Studieren aus der Perspektive von Studieninteressierten, Dozierenden und Beratungsstellen: Bedarf im Bereich virtuelle Lehre und Diversit{\"a}t der Studierenden}, series = {Akademische Weiterbildung f{\"u}r soziale Berufe. Theoretische, empirische und praktische Aspekte}, booktitle = {Akademische Weiterbildung f{\"u}r soziale Berufe. Theoretische, empirische und praktische Aspekte}, editor = {Sch{\"o}pf, Nicolas}, publisher = {WBV Media}, address = {Bielefeld}, isbn = {978-3-7639-6646-2}, pages = {107 -- 126}, abstract = {Die sozialwissenschaftliche Begleitforschung zum Projekt WANTED (Wissens-management, Aktualit{\"a}t, Netzwerk,Transfer, Entwicklung, Diversit{\"a}t) an der OTH Regensburg zielte auf die inhaltlichen Schwerpunkte Flexibilisierung bzw. Digitalisie-rung und Diversit{\"a}t der Zielgruppen, insbesondere im Hinblick auf Personen mit Migrationshintergrund. Zur Erhebung und Bewertung des Bedarfs und der Passgenauigkeit der geplanten Angebote wurden vier Erhebungen mit verschiedenen Stake-holdern durchgef{\"u}hrt: Weiterbildungsinteressierte, Dozierende berufsbegleitender Bachelorstudieng{\"a}nge sowie Beratungsstellen f{\"u}r (Weiter-)Bildung. Bei der quantitativen und qualitativen Analyse zeigt sich ein Bedarf nach Vereinbarkeit von Familie, Beruf und Studium sowie eine Erweiterung des Angebots an Auswahlm{\"o}glichkeiten, digitaler Lehre, Modularisierung und verbesserter Informationsverbreitung.}, language = {de} } @incollection{HaugCurrleFrommeldetal., author = {Haug, Sonja and Currle, Edda and Frommeld, Debora and Weber, Karsten}, title = {Telepr{\"a}senzroboter f{\"u}r die Pflege und Unterst{\"u}tzung von Schlaganfallpatientinnen und -patienten: Das Forschungsdesign f{\"u}r die sozialwissenschaftliche Begleitforschung}, series = {Digitale Technik f{\"u}r ambulante Pflege und Therapie: Herausforderungen, L{\"o}sungen, Anwendungen und Forschungsperspektiven}, booktitle = {Digitale Technik f{\"u}r ambulante Pflege und Therapie: Herausforderungen, L{\"o}sungen, Anwendungen und Forschungsperspektiven}, editor = {Weber, Karsten and Haug, Sonja and Lauer, Norina and Meussling-Sentpali, Annette and Mohr, Christa and Pfingsten, Andrea and Raptis, Georgios and Bahr, Gudrun}, publisher = {Transcript}, address = {Bielefeld}, isbn = {978-3-8376-6235-1}, doi = {10.14361/9783839462355-009}, pages = {175 -- 193}, language = {de} } @inproceedings{CurrleHaug, author = {Currle, Edda and Haug, Sonja}, title = {Acceptance of Telepresence Robotics, Telecare and Teletherapy Among Stroke Patients, Relatives and Therapy Staff}, series = {dHealth 2024: proceedings of the 18th annual conference on Health Informatics meets Digital Health conference}, booktitle = {dHealth 2024: proceedings of the 18th annual conference on Health Informatics meets Digital Health conference}, publisher = {IOS Press}, isbn = {978-1-64368-517-5}, issn = {0926-9630}, doi = {10.3233/SHTI240005}, pages = {15 -- 21}, abstract = {Background: Stroke as a cause of disability in adulthood causes an increasing demand for therapy and care services, including telecare and teletherapy. Objectives: Aim of the study is to analyse the acceptance of telepresence robotics and digital therapy applications. Methods: Longitudinal study with a before and after survey of patients, relatives and care and therapy staff. Results: Acceptance of the technology analysed is high in all three groups. Although acceptance among patients declined in parts of the cases in the second survey after having used telerobotics, all in all approval ratings remained high. With regard to patients no significant correlation was found between the general technology acceptance and the acceptance of use of telerobotics. Conclusion: Accepted new telecare and teletherapies can be offered with the help of telepresence robotics. This requires knowledge of and experience with the technology.}, language = {en} } @incollection{Haug, author = {Haug, Sonja}, title = {Digitale Technik f{\"u}r ambulante Pflege und Therapie II - zukunftsweisende Wege}, series = {Digitale Technik f{\"u}r ambulante Pflege und Therapie II - Impulse f{\"u}r die Praxis}, booktitle = {Digitale Technik f{\"u}r ambulante Pflege und Therapie II - Impulse f{\"u}r die Praxis}, editor = {Weber, Karsten and Haug, Sonja and Lauer, Norina and Mohr, Christa and Pfingsten, Andrea and Raptis, Georgios and Bahr, Gudrun}, publisher = {transcript}, address = {Bielefeld}, isbn = {978-3-8394-6727-5}, doi = {10.14361/9783839467275-002}, pages = {11 -- 19}, language = {de} } @incollection{Weber, author = {Weber, Karsten}, title = {Der Einsatz von Telepr{\"a}senzrobotern als normatives Gebot: Ein Pl{\"a}doyer f{\"u}r mehr Technikoffenheit und Technikeinsatz in Pflege und Gesundheit}, series = {Digitale Technik f{\"u}r ambulante Pflege und Therapie: Herausforderungen, L{\"o}sungen, Anwendungen und Forschungsperspektiven}, booktitle = {Digitale Technik f{\"u}r ambulante Pflege und Therapie: Herausforderungen, L{\"o}sungen, Anwendungen und Forschungsperspektiven}, editor = {Weber, Karsten and Haug, Sonja and Lauer, Norina and Meussling-Sentpali, Annette and Mohr, Christa and Pfingsten, Andrea and Raptis, Georgios and Bahr, Gudrun}, publisher = {Transcript}, address = {Bielefeld}, isbn = {978-3-8376-6235-1}, doi = {10.14361/9783839462355-014}, pages = {317 -- 334}, language = {de} } @incollection{Weber, author = {Weber, Karsten}, title = {DeinHaus 4.0 Oberpfalz - Feldstudie, Schaufenster und Stolpersteine}, series = {Digitale Technik f{\"u}r ambulante Pflege und Therapie}, booktitle = {Digitale Technik f{\"u}r ambulante Pflege und Therapie}, editor = {Weber, Karsten and Haug, Sonja and Lauer, Norina and Meussling-Sentpali, Annette and Mohr, Christa and Pfingsten, Andrea and Raptis, Georgios and Bahr, Gudrun}, publisher = {Transcript}, address = {Bielefeld}, isbn = {978-3-8376-6235-1}, doi = {10.14361/9783839462355}, pages = {9 -- 17}, language = {de} } @inproceedings{AltenbuchnerMueckeHaug, author = {Altenbuchner, Amelie and M{\"u}cke, Vanessa and Haug, Sonja}, title = {Comparing monitoring results of two motion trackers for geriatric patients}, series = {dHealth 2020: biomedical informatics for health and care, proceedings of the 14th Health Informatics Meets Digital Health Conference}, booktitle = {dHealth 2020: biomedical informatics for health and care, proceedings of the 14th Health Informatics Meets Digital Health Conference}, editor = {Schreier, G{\"u}nter}, publisher = {IOS Press}, address = {Amsterdam}, isbn = {978-1-64368-085-9}, doi = {10.3233/SHTI200078}, pages = {77 -- 84}, abstract = {Background: Fitbit and Garmin motion tracker devices are highly used in research. The validity and reliability of these devices is proven for healthy adults between 18 and 64. Objectives: Comparing data output of two devices. Methods: Observational case study on a test track and in the domestic environment of a 80- year-old female multimorbide geriatric patient. Results: High significant correlation of the devices on the test track [r=.776, p≤.001, Bca-CI-95\% (.618;.874), N=33], but significant different in the domestic environment over time (z=4.840, p≤.001). Conclusion: The dominant/non-dominant body side and further sources of error may play a role in monitoring steps with these devices.}, language = {en} } @article{HaugVetterWeber, author = {Haug, Sonja and Vetter, Miriam and Weber, Karsten}, title = {Geb{\"a}udesanierung zwischen Energieeffizienz und Sozialvertr{\"a}glichkeit}, series = {TATuP - Zeitschrift f{\"u}r Technikfolgenabsch{\"a}tzung in Theorie und Praxis}, volume = {29}, journal = {TATuP - Zeitschrift f{\"u}r Technikfolgenabsch{\"a}tzung in Theorie und Praxis}, number = {3}, publisher = {oekom-Verlag}, issn = {2567-8833}, doi = {10.14512/tatup.29.3.56}, pages = {56 -- 63}, abstract = {Die Akzeptanz unter Bewohnern und Bewohnerinnen gewinnt bei hoch komplexen, technisch anspruchsvollen energetischen Sanierungen als „Innovationsmotor" zunehmend an Relevanz. Der Beitrag basiert auf zwei Fallstudien zur partizipativen Nutzereinbindung bei energetischen Sanierungen im genossenschaftlichen Wohnbau historischer Stadtquartiere in Regensburg. Neben einer sozialvertr{\"a}glichen Sanierung wurde jeweils ein hohes Maß an Energieeffizienz bei den technischen L{\"o}sungen ange-strebt. Haushaltsbefragungen und qualitative Interviews zeigen die hohe Akzeptanz von Sanierungsmaßnahmen, sofern die Senkung der Energiekosten die erh{\"o}hte Miete kompensiert. Abschließend werden Akzeptanzfaktoren wie Partizipation, Vertrauen, Sozialvertr{\"a}glichkeit und Autarkie er{\"o}rtert.}, subject = {Altbaumodernisierung}, language = {de} } @article{HaugMilewski, author = {Haug, Sonja and Milewski, Nadja}, title = {Women's attitudes towards assisted reproductive technologies}, series = {Comparative Population Studies. Special Collection on "New aspects in fertility of migrant and minority populations in Europe: The role of attitudes and intentions in family planning"}, volume = {Vol. 43}, journal = {Comparative Population Studies. Special Collection on "New aspects in fertility of migrant and minority populations in Europe: The role of attitudes and intentions in family planning"}, organization = {Federal Institute for Population Research     }, doi = {10.12765/CPoS-2019-06}, pages = {343 -- 370}, abstract = {This study examines attitudes toward assisted reproductive technologies (ART) among immigrant women and non-migrants in Germany. The social relevance of ART is increasing in Western countries due to overall low birth rates, a high rate of childlessness, and a gap between the desired and the actual numbers of children. Previous literature has been scarce, however, on attitudes toward ART, and immigrant minorities have rarely been included in studies on ART. Our working hypotheses are drawn from theoretical considerations on political socialisation and cultural integration. The analysis is based on data collected in a pilot study in 2014 and 2015. The sample includes 960 women aged 18 to 50 living in Germany. About 81 percent of the sample are immigrants who originate from Turkey, Poland, the Balkan countries, or countries of the (Russian) Commonwealth of Independent States (CIS). We study the social norm to use ART to have a child, the personal attitude of whether a woman would use ART herself, and the methods that they would consider for their own use. Our results show that ART is overall socially acceptable, and the majority of women said that they would use it if necessary. There is significant variation between the origin groups, however. Non-migrants show the lowest acceptance rates and migrants from Poland and Turkey the highest approval. There is also variation in the ART procedures considered for use with the migrants more approving of heterologous methods than non-migrants. The differences between the origin groups diminish only partly when controlling for further explanatory variables, i.e. gender-role attitudes, religiosity, and socio-demographic characteristics of the respondents. We conclude that attitudes toward ART are shaped less by socio-demographic characteristics, but rather by cultural factors and the socialization in the migrants' countries of origin. The diversity in attitudes toward ART by cultural background should be acknowledged in research and public discourses on ART as well as in regulating policies.}, language = {en} } @article{SnarskiiKalitaShamoninChamonine, author = {Snarskii, Andrei A. and Kalita, Viktor M. and Shamonin (Chamonine), Mikhail}, title = {Renormalization of the critical exponent for the shear modulus of magnetoactive elastomers}, series = {Scientific Reports}, volume = {8}, journal = {Scientific Reports}, publisher = {Nature}, doi = {10.1038/s41598-018-22333-6}, pages = {1 -- 8}, abstract = {It is shown that the critical exponent for the effective shear modulus of a composite medium where a compliant polymer matrix is filled with ferromagnetic particles may significantly depend on the external magnetic field. The physical consequence of this dependence is the critical behavior of the relative magnetorheological effect.}, language = {en} } @article{PrantlEigenbergerReinhardetal., author = {Prantl, Lukas and Eigenberger, Andreas and Reinhard, Ruben and Siegmund, Andreas and Heumann, Kerstin and Felthaus, Oliver}, title = {Cell-Enriched Lipotransfer (CELT) Improves Tissue Regeneration and Rejuvenation without Substantial Manipulation of the Adipose Tissue Graft}, series = {Cells}, volume = {11}, journal = {Cells}, number = {19}, publisher = {MDPI}, doi = {10.3390/cells11193159}, pages = {1 -- 11}, abstract = {The good availability and the large content of adult stem cells in adipose tissue has made it one of the most interesting tissues in regenerative medicine. Although lipofilling is one of the most frequent procedures in plastic surgery, the method still struggles with high absorption rates and volume losses of up to 70\%. Therefore, many efforts have been made to optimize liposuction and to process the harvested tissue in order to increase fat graft retention. Because of their immunomodulatory properties, their cytokine secretory activity, and their differentiation potential, enrichment with adipose tissue-derived stem cells was identified as a promising tool to promote transplant survival. Here, we review the important parameters for lipofilling optimization. Finally, we present a new method for the enrichment of lipoaspirate with adipose tissue-derived stem cells and discuss the parameters that contribute to fat graft survival.}, language = {en} } @article{LaumerKargSchmidt, author = {Laumer, Tobias and Karg, Michael Cornelius Hermann and Schmidt, Michael}, title = {Laser Beam Melting of Multi-Material Components}, series = {Physics Procedia}, volume = {39}, journal = {Physics Procedia}, publisher = {Elsevier}, issn = {1875-3892}, doi = {10.1016/j.phpro.2012.10.068}, pages = {518 -- 525}, abstract = {First results regarding the realisation of multi-material components manufactured by Laser Beam Melting of polymers and metals are published. For realising composite structures from polymer powders by additive manufacturing, at first relevant material properties regarding compatibility have to be analysed. The paper shows the main requirements for compatibility between different materials and offers first results in form of a compatibility matrix of possible combinations for composite structures.For achieving gradient properties of additively manufactured metal parts by using composite materials the composition of alloying components in the powder and adapted process strategies are varied. As an alternative to atomizing pre-alloyed materials, mixtures of different powders are investigated.}, language = {en} } @article{WidbillerKeimSchlichtingetal., author = {Widbiller, Matthias and Keim, Lukas and Schlichting, Ralf and Striegl, Birgit and Hiller, Karl-Anton and Jungbauer, Rebecca and Buchalla, Wolfgang and Galler, Kerstin M.}, title = {Debris Removal by Activation of Endodontic Irrigants in Complex Root Canal Systems}, series = {Applied Sciences}, volume = {11}, journal = {Applied Sciences}, number = {16}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/app11167331}, pages = {1 -- 14}, abstract = {Aim of the study was to develop a standardized model system to investigate endodontic irrigation techniques and assess the efficiency of different activation methods on the removal of hard tissue debris in complex root canal systems. Mesial roots of mandibular molars were firstly scanned by micro-computed tomography (µCT) and allocated to three groups of irrigant activation: sonic activation (EDDY, VDW, Munich, Germany), laser activation (AutoSWEEPS, FOTONA, Ljubljana, Slovenia) and conventional needle irrigation (control). Roots were fixed in individual 3D-printed holders to facilitate root canal enlargement under constant irrigation with NaOCl (5\%). To enable standardized quantification of remaining debris, BaSO4-enriched dentine powder was compacted into the canals, followed by another µCT-scan. The final irrigation was performed using 17\% ethylenediaminetetraacetic acid (EDTA) and 5\% sodium hypochlorite (NaOCl) with the respective activation method, and the volume of remaining artificial debris was quantified after a final µCT-scan. The newly developed model system allowed for reliable, reproducible and standardized assessment of irrigation methods. Activation of the irrigant proved to be significantly more effective than conventional needle irrigation regarding the removal of debris, which persisted particularly in the apical third of the root canal in the control group. The efficiency of irrigation was significantly enhanced with laser- and sonic-based activation, especially in the apical third.}, language = {en} } @incollection{Giese, author = {Giese, Constanze}, title = {Roboter als Hoffnungstr{\"a}ger in der Pflege: Pflegeethische Zug{\"a}nge zur Einsch{\"a}tzung k{\"u}nftiger Einsatzm{\"o}glichkeiten}, series = {Digitale Technik f{\"u}r ambulante Pflege und Therapie II - Impulse f{\"u}r die Praxis}, booktitle = {Digitale Technik f{\"u}r ambulante Pflege und Therapie II - Impulse f{\"u}r die Praxis}, editor = {Weber, Karsten and Haug, Sonja and Mohr, Christa and Lauer, Norina and Pfingsten, Andrea and Raptis, Georgios and Bahr, Gudrun}, publisher = {transcript}, address = {Bielefeld}, doi = {10.14361/9783839467275-010}, pages = {115 -- 130}, language = {de} } @article{OsmanlicWudyLaumeretal., author = {Osmanlic, Fuad and Wudy, Katrin and Laumer, Tobias and Schmidt, Michael and Drummer, Dietmar and K{\"o}rner, Carolin}, title = {Modeling of Laser Beam Absorption in a Polymer Powder Bed}, series = {Polymers}, volume = {10}, journal = {Polymers}, number = {7}, publisher = {MDPI}, doi = {10.3390/polym10070784}, pages = {1 -- 11}, abstract = {In order to understand the absorption characteristic, a ray trace model is developed by taking into account the reflection, absorption and refraction. The ray paths are resolved on a sub-powder grid. For validation, the simulation results are compared to analytic solutions of the irradiation of the laser beam onto a plain surface. In addition, the absorptance, reflectance and transmittance of PA12 powder layers measured by an integration sphere setup are compared with the numerical results of our model. It is shown that the effective penetration depth can be lower than the penetration depth in bulk material for polymer powders and, therefore, can increase the energy density at the powder bed surface. The implications for modeling of the selective laser sintering (SLS) process and the processability of fine powder distributions and high powder bed densities are discussed.}, language = {en} } @misc{RollerRudolphEcketal., author = {Roller, Katrin and Rudolph, Clarissa and Eck, Sandra and Schneider, Kyra and Vischer, Nina}, title = {Wohnen, Care, Geschlecht - Theorie und Praxis kollektiven Wohnens aus Geschlechterperspektive}, publisher = {Westf{\"a}lisches Dampfboot}, address = {M{\"u}nster}, isbn = {978-3-98634-175-6}, doi = {10.56715/398634175}, language = {de} } @article{HaynackSekandarJithenderetal., author = {Haynack, Alexander and Sekandar, Zadran and Jithender, J. Timothy and Gambarelli, Serena and Kr{\"a}nkel, Thomas and Thiel, Charlotte and Ozbolt, Josko and Gehlen, Christoph}, title = {Can a Hend-Held 3D Scanner Capture Temperature-Induced Strain of Mortar Samples? Comparison between Experimental Measurements and Numerical Simulations}, series = {mathematics}, volume = {11}, journal = {mathematics}, number = {17}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/math11173672}, abstract = {The expected lifespan of cement-based materials, particularly concrete, is at least 50 years. Changes in the pore structure of the material need to be considered due to external influences and associated transport processes. The expansion behaviour of concrete and mortar during freeze-thaw attacks, combined with de-icing salt agents, is crucial for both internal and external damage. It is essential to determine and simulate the expansion behaviour of these materials in the laboratory, as well as detect the slow, long-term expansion in real structures. This study measures the expansion of mortar samples during freeze-thaw loading using a high-resolution hand-held 3D laser scanner. The specimens are prepared with fully or partially saturated pore structures through water storage or drying. During freeze-thaw experiments, the specimens are exposed to pure water or a 3\% sodium chloride solution (NaCl). Results show contraction during freezing and subsequent expansion during thawing. Both test solutions exhibit similar expansion behaviour, with differences primarily due to saturation levels. Further investigations are required to explore the changing expansion behaviour caused by increasing microcracking resulting from continuous freeze-thaw cycles. A numerical analysis using a 3D coupled hygro-thermo-mechanical (HTM) model is conducted to examine the freeze-thaw behaviour of the mortar. The model accurately represents the freezing deformation during the freeze-thaw cycle.}, language = {en} } @article{KruegerFischerManoonpongetal., author = {Kr{\"u}ger, Norbert and Fischer, Kerstin and Manoonpong, Poramate and Palinko, Oskar and Bodenhagen, Leon and Baumann, Timo and Kj{\ae}rum, Jens and Rano, Ignacio and Naik, Lakshadeep and Juel, William Kristian and Haarslev, Frederik and Ignasov, Jevgeni and Marchetti, Emanuela and Langedijk, Rosalyn Melissa and Kollakidou, Avgi and Jeppesen, Kasper Camillus and Heidtmann, Conny and Dalgaard, Lars}, title = {The SMOOTH-Robot: A Modular, Interactive Service Robot}, series = {Frontiers in Robotics and AI}, volume = {8}, journal = {Frontiers in Robotics and AI}, publisher = {Frontiers}, doi = {10.3389/frobt.2021.645639}, abstract = {The SMOOTH-robot is a mobile robot that-due to its modularity-combines a relatively low price with the possibility to be used for a large variety of tasks in a wide range of domains. In this article, we demonstrate the potential of the SMOOTH-robot through three use cases, two of which were performed in elderly care homes. The robot is designed so that it can either make itself ready or be quickly changed by staff to perform different tasks. We carefully considered important design parameters such as the appearance, intended and unintended interactions with users, and the technical complexity, in order to achieve high acceptability and a sufficient degree of utilization of the robot. Three demonstrated use cases indicate that such a robot could contribute to an improved work environment, having the potential to free resources of care staff which could be allocated to actual care-giving tasks. Moreover, the SMOOTH-robot can be used in many other domains, as we will also exemplify in this article.}, language = {en} } @article{AlvarezMoretObermeierPohletal., author = {Alvarez Moret, Judit and Obermeier, Tina and Pohl, Fabian and L{\"o}schel, Rainer and K{\"o}lbl, Oliver and Dobler, Barbara}, title = {Second cancer risk after radiation therapy of ependymoma using the flattening filter free irradiation mode of a linear accelerator}, series = {Journal of Applied Clinical Medical Physics}, volume = {19}, journal = {Journal of Applied Clinical Medical Physics}, number = {5}, publisher = {Wiley}, organization = {American Association of Physicists in Medicine}, doi = {10.1002/acm2.12438}, pages = {632 -- 639}, abstract = {Pediatric patients suffering from ependymoma are usually treated with cranial or craniospinal three-dimensional (3D) conformal radiotherapy (3DCRT). Intensity-modulated techniques spare dose to the surrounding tissue, but the risk for second malignancies may be increased due to the increase in low-dose volume. The aim of this study is to investigate if the flattening filter free (FFF) mode allows reducing the risk for second malignancies compared to the mode with flattening filter (FF) for intensity-modulated techniques and to 3DCRT. A reduction of the risk would be advantageous for treating pediatric ependymoma. 3DCRT was compared to intensity-modulated radiation therapy (IMRT) and volumetric-modulated arc therapy (VMAT) with and without flattening filter. Dose-volume histograms (DVHs) were compared to evaluate the plan quality and used to calculate the excess absolute risk (EAR) to develop second cancer in the brain. Dose verification was performed with a two-dimensional (2D) ionization chamber array and the out-of-field dose was measured with an ionization chamber to determine the EAR in peripheral organs. Delivery times were measured. Both VMAT and IMRT achieved similar plan quality in terms of dose sparing in the OAR and higher PTV coverage as compared to 3DCRT. Peripheral dose in low-dose region, which is proportional to the EAR in organs located in this region, for example, gonads, bladder, or bowel, could be significantly reduced using FFF. The lowest peripheral EAR and lowest delivery times were hereby achieved with VMATFFF . The EAR calculated based on DVH in the brain could not be reduced using FFF mode. VMATFFF improved the target coverage and homogeneity and kept the dose in the OAR similar compared to 3DCRT. In addition, delivery times were significantly reduced using VMATFFF . Therefore, for radiotherapy of ependymoma patients, VMATFFF may be considered advantageous for the combination of Elekta Synergy linac and Oncentra External Beam planning system used in this study.}, language = {en} } @article{MikhaeilGadererDawoud, author = {Mikhaeil, Makram and Gaderer, Matthias and Dawoud, Belal}, title = {Experimental Investigation of the Adsorption and Desorption Kinetics on an Open-Structured Asymmetric Plate Heat Exchanger; Matching Between Small-Scale and Full-Scale Results}, series = {Frontiers in Energy Research}, volume = {10}, journal = {Frontiers in Energy Research}, publisher = {Frontiers}, doi = {10.3389/fenrg.2022.818486}, pages = {1 -- 15}, abstract = {This paper introduces the results of an experimental study on the adsorption and desorption kinetics of a commercially available, open-structured asymmetric plate heat exchanger adapted to act as an adsorber/desorber for the application in adsorption heat transformation processes. In addition, a volumetric large temperature jump (V-LTJ) kinetic setup was applied to measure the adsorption and desorption kinetics of a small-scale adsorbent sample prepared dedicatedly to be representative for the adsorbent domain inside the investigated adsorber plate heat exchanger (APHE). All kinetic results of the small-scale adsorbent sample and the APHE were fitted into exponential forms with a single characteristic time constant (τ) with a coefficient of determination (R2) better than 0.9531. A very good matching between the small-scale and full-scale adsorption kinetic measurements was obtained, with an average relative deviation of 12.3\% in the obtained τ-values. In addition, the kinetic data of the small-scale adsorbent sample were utilized for estimating the expected specific instantaneous and moving average powers of the evaporator/condenser heat exchanger. The average relative deviation (ARD) between the moving average specific evaporator powers obtained from the small-scale and the full-scale measurements amounts between 5.4 and 15.1\%.}, language = {en} } @article{CurbachLanderDierksetal., author = {Curbach, Janina and Lander, Jonas and Dierks, Marie-Luise and Grepmeier, Eva-Maria and von Sommoggy, Julia}, title = {How do health professionals translate evidence on early childhood allergy prevention into health literacy-responsive practice?}, series = {BMJ OPEN}, volume = {11}, journal = {BMJ OPEN}, publisher = {BMJ}, doi = {10.1136/bmjopen-2020-047733}, pages = {1 -- 8}, abstract = {Introduction Paediatricians, general practitioners (GPs) and midwives in primary care are important sources of information for parents on early childhood allergy prevention (ECAP). Research has shown that preventive counselling by health professionals can be effective in improving patients' health literacy (HL) and health behaviour. Providing effective advice relies on two factors. First, health professionals need be up-to-date with research evidence on ECAP, to consider popular misconceptions and fears and to translate this knowledge into clear recommendations for parents (knowledge translation). Second, they need to know and apply counselling techniques and create a practice setting which accommodates parental HL needs (health literacy-responsive care). The objective of this study is to explore and assess how German health professionals take up and translate ECAP evidence into appropriate recommendations for parents, how they consider HL in counselling and practice organisation and what barriers and enablers they find in their performance of HL-responsive ECAP. Methods and analysis The study has a sequential mixed-method design, in two phases. In the first phase, qualitative semi-structured expert interviews will be conducted with health professionals (paediatricians, GPs and midwives) at primary care level and professional policy level. Data collection is ongoing until January 2022. In the second phase, based on the qualitative results, a standardised questionnaire will be developed, and pilot-tested in a wider population of German health professionals. The findings of both phases will be integrated. Ethics and dissemination The study has received ethical approval from the Ethics Committee of the University of Regensburg (18-1205-101). The results will be published in international peer-reviewed open access journals and via presentations at scientific conferences. The results will also be shared with German health professionals, decision-makers and potential funders of interventions.}, language = {en} } @article{BerndtMuggliHeckeletal., author = {Berndt, Dominik and Muggli, Josef and Heckel, Robert and Rahiman, Mohd Fuad and Lindner, Matthias and Heinrich, Stephan and Pl{\"o}chinger, Heinz and Schreiner, Rupert}, title = {A Robust Miniaturized Gas Sensor for H₂ and CO₂ Detection Based on the 3ω Method}, series = {Sensors}, volume = {22}, journal = {Sensors}, number = {2}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/s22020485}, pages = {1 -- 17}, abstract = {Gas concentration monitoring is essential in industrial or life science areas in order to address safety-relevant or process-related questions. Many of the sensors used in this context are based on the principle of thermal conductivity. The 3ω-method is a very accurate method to determine the thermal properties of materials. It has its origin in the thermal characterization of thin solid films. To date, there have been very few scientific investigations using this method to determine the thermal properties of gases and to apply it to gas measurement technology. In this article, we use two exemplary gases (H2 and CO2) for a systematical investigation of this method in the context of gas analysis. To perform our experiments, we use a robust, reliable sensing element that is already well established in vacuum measurement technology. This helix-shaped thin wire of tungsten exhibits high robustness against chemical and mechanical influences. Our setup features a compact measurement environment, where sensor operation and data acquisition are integrated into a single device. The experimental results show a good agreement with a simplified analytical model and FEM simulations. The sensor exhibits a lower detection limit of 0.62\% in the case of CO2, and only 0.062\% in case the of H2 at an excitation frequency of 1 Hz. This is one of the lowest values reported in literature for thermal conductivity H2 sensors.}, language = {en} } @article{SteiningerGadererSteffensetal., author = {Steininger, Peter and Gaderer, Matthias and Steffens, Oliver and Dawoud, Belal}, title = {Experimental and Numerical Study on the Heat Transfer Characteristics of a Newly-Developed Solar Active Thermal Insulation System}, series = {Buildings}, volume = {11}, journal = {Buildings}, number = {3}, publisher = {MDPI}, doi = {10.3390/buildings11030123}, pages = {1 -- 22}, abstract = {A newly-developed solar active thermal insulation system (SATIS) is introduced with the main objective to accomplish a highly-dependent total solar transmittance on the irradiation angle. SATIS is also designed to obtain the maximum transmittance at a prescribed design irradiation angle and to reduce it remarkably at higher irradiation angles. A purely mineral thermal insulation plaster with micro hollow glass spheres is applied to manufacture the investigated SATIS prototype. Light-conducting elements (LCEs) have been introduced into SATIS and suitable closing elements have been applied. The SATIS prototype has been investigated both experimentally and numerically. It turned out that the contributions of conduction, radiation and convection to the effective thermal conductivity of SATIS, without the closing elements (49 mWmK), amount to 86.2\%, 13.2\% and 0.6\%, respectively. The angle-dependent short-wave radiation exchange within the LCE has been investigated via ray tracing. At the incidence angle of 19\% (design angle), 27\% of the radiation within the LCE is absorbed by the absorber plate, resulting in measured and computed total solar energy transmittances of 11.2\%/11.7\%, respectively. For a typical summer irradiation angle of 60\%, 98\% of the incident radiation is absorbed by the surfaces at the entrance of the LCE. The corresponding total solar energy transmittance amounts to 2.9\%.}, language = {en} } @article{GamischGadererDawoud, author = {Gamisch, Bernd and Gaderer, Matthias and Dawoud, Belal}, title = {On the Development of Thermochemical Hydrogen Storage: An Experimental Study of the Kinetics of the Redox Reactions under Different Operating Conditions}, series = {Applied Sciences}, volume = {11}, journal = {Applied Sciences}, number = {4}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/app11041623}, pages = {1 -- 15}, abstract = {This work aims at investigating the reduction/oxidation (redox) reaction kinetics on iron oxide pellets under different operating conditions of thermochemical hydrogen storage. In order to reduce the iron oxide pellets (90\% Fe2O3, 10\% stabilizing cement), hydrogen (H2) is applied in different concentrations with nitrogen (N2), as a carrier gas, at temperatures between between 700 ∘C and 900 ∘C, thus simulating the charging phase. The discharge phase is triggered by the flow of a mixture out of steam (H2O) and N2 at different concentrations in the same temperature range, resulting in the oxidizing of the previously reduced pellets. All investigations were carried out in a thermo-gravimetric analyzer (TGA) with a flow rate of 250mL/min. To describe the obtained kinetic results, a simplified analytical model, based on the linear driving force model, was developed. The investigated iron oxide pellets showed a stable redox performance of 23.8\% weight reduction/gain, which corresponds to a volumetric storage density of 2.8kWh/(L bulk), also after the 29 performed redox cycles. Recalling that there is no H2 stored during the storage phase but iron, the introduced hydrogen storage technology is deemed very promising for applications in urban areas as day-night or seasonal storage for green hydrogen.}, language = {en} } @article{PremSindersbergerMonkman, author = {Prem, Nina and Sindersberger, Dirk and Monkman, Gareth J.}, title = {Mini-Extruder for 3D Magnetoactive Polymer Printing}, series = {Advances in Materials Science and Engineering}, journal = {Advances in Materials Science and Engineering}, publisher = {HINDAWI}, doi = {10.1155/2019/8715718}, pages = {1 -- 8}, abstract = {This work describes the development of a new miniature extruder, essential to cavity-free 3D printing of silicone-based smart materials. This makes the 3D printing of magnetoactive and electroactive polymer soft robotic components and devices directly from CAD data possible. The special feature of such an extruder is that it is designed for use with addition-crosslinking RTV-2 silicones, including solid particulate additives. The extruder merges the respective components automatically during extrusion which obviates the need for premixing and vacuum evacuation. Problems associated with inhomogeneities and unwanted cavity production are consequently eliminated. Rheological details necessary to the design, together with some preliminary performance results, are presented.}, language = {en} } @article{DechantFedulovFetisovetal., author = {Dechant, Eduard and Fedulov, Feodor and Fetisov, Leonid Y. and Shamonin (Chamonine), Mikhail}, title = {Bandwidth Widening of Piezoelectric Cantilever Beam Arrays by Mass-Tip Tuning for Low-Frequency Vibration Energy Harvesting}, series = {Applied Science}, volume = {7}, journal = {Applied Science}, number = {12}, publisher = {MDPI}, organization = {MDPI AG}, doi = {10.3390/app7121324}, abstract = {Wireless sensor networks usually rely on internal permanent or rechargeable batteries as a power supply, causing high maintenance efforts. An alternative solution is to supply the entire system by harvesting the ambient energy, for example, by transducing ambient vibrations into electric energy by virtue of the piezoelectric effect. The purpose of this paper is to present a simple engineering approach for the bandwidth optimization of vibration energy harvesting systems comprising multiple piezoelectric cantilevers (PECs). The frequency tuning of a particular cantilever is achieved by changing the tip mass. It is shown that the bandwidth enhancement by mass tuning is limited and requires several PECs with close resonance frequencies. At a fixed frequency detuning between subsequent PECs, the achievable bandwidth shows a saturation behavior as a function of the number of cantilevers used. Since the resonance frequency of each PEC is different, the output voltages at a particular excitation frequency have different amplitudes and phases. A simple power-transfer circuit where several PECs with an individual full wave bridge rectifier are connected in parallel allows one to extract the electrical power close to the theoretical maximum excluding the diode losses. The experiments performed on two- and three-PEC arrays show reasonable agreement with simulations and demonstrate that this power-transfer circuit additionally influences the frequency dependence of the harvested electrical power.}, language = {en} } @article{Diamantidis, author = {Diamantidis, Dimitris}, title = {A Critical View on Environmental and Human Risk Acceptance Criteria}, series = {International Journal of Environmental Science and Development}, volume = {8}, journal = {International Journal of Environmental Science and Development}, number = {1}, doi = {10.18178/ijesd.2017.8.1.921}, pages = {62 -- 66}, abstract = {Natural and technological hazards have a major impact on environmental and human safety. Risk assessment plays an essential role in the risk management of the effects of such hazards. This contribution summarizes first the general formulation of risk depending on two parameters: hazard probability and associated consequences. Problems faced in industrial applications based on the experience of the author are discussed. Risk acceptance criteria for the contributors to risk i.e. human, economic and environment are critically reviewed. Resilience based criteria are also included and conclusions for future developments are provided.}, language = {en} } @article{KreitmeierChashinFetisovetal., author = {Kreitmeier, Florian and Chashin, Dmitri V. and Fetisov, Yuri K. and Fetisov, Leonid Y. and Schulz, Irene and Monkman, Gareth J. and Shamonin (Chamonine), Mikhail}, title = {Nonlinear Magnetoelectric Response of Planar Ferromagnetic-Piezoelectric Structures to Sub-Millisecond Magnetic Pulses}, series = {Sensors}, volume = {12}, journal = {Sensors}, number = {11}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/s121114821}, pages = {14821 -- 14837}, abstract = {The magnetoelectric response of bi- and symmetric trilayer composite structures to pulsed magnetic fields is experimentally investigated in detail. The structures comprise layers of commercially available piezoelectric (lead zirconate titanate) and magnetostrictive (permendur or nickel) materials. The magnetic-field pulses have the form of a half-wave sine function with duration of 450 µs and amplitudes ranging from 500 Oe to 38 kOe. The time dependence of the resulting voltage is presented and explained by theoretical estimations. Appearance of voltage oscillations with frequencies much larger than the reciprocal pulse length is observed for sufficiently large amplitudes (~1-10 kOe) of the magnetic-field pulse. The origin of these oscillations is the excitation of bending and planar acoustic oscillations in the structures. Dependencies of the magnetoelectric voltage coefficient on the excitation frequency and the applied magnetic field are calculated by digital signal processing and compared with those obtained by the method of harmonic field modulation. The results are of interest for developing magnetoelectric sensors of pulsed magnetic fields as well as for rapid characterization of magnetoelectric composite structures.}, language = {en} } @article{ApelsmeierGleixnerMayeretal., author = {Apelsmeier, Andreas and Gleixner, Ramona and Mayer, Matthias and Shamonin (Chamonine), Mikhail and Schmauss, Bernhard}, title = {Intensity referencing in an extrinsic optical fiber temperature sensor}, series = {Procedia Engineering}, volume = {5}, journal = {Procedia Engineering}, publisher = {Elsevier}, doi = {10.1016/j.proeng.2010.09.301}, pages = {1095 -- 1098}, abstract = {Optical fiber sensors based on intensity measurement require some form of intensity referencing to avoid errors arising from parasitic losses. Known techniques of referencing such as balanced bridge, divided beam systems or two-wavelength referencing are not suitable for low-cost applications since they use relatively complicated optical components such as multiple LED sources, couplers, filters etc. In this work a novel method of referencing in an extrinsic optical fiber sensor system utilizing temperature dependence of absorption edge in a semiconductor crystal is described. The sensor system comprises a single LED source and no optical fiber junctions. The emission spectrum of an LED depends on its temperature. The reference is provided by controlling the temperature of an LED source and transmission measurements with different emission spectra. The entire process is controlled by a microprocessor unit. Performance of a sensor system is investigated and it is shown that the losses in connectors may be compensated for.}, language = {en} } @article{MonkmanSindersbergerPremetal., author = {Monkman, Gareth J. and Sindersberger, Dirk and Prem, Nina and Szecsey, Tamara}, title = {Smart Stiction}, series = {Robotics \& Automation Engineering Journal}, volume = {4}, journal = {Robotics \& Automation Engineering Journal}, number = {4}, publisher = {Juniper Publishers}, doi = {10.19080/RAEJ.2019.04.555641}, abstract = {Soft robotics could loosely be described as the engineering science of expanded dexterity through controllable flexibility. The exploitation of controllable compliance through the judicious choice of soft flexible members, as opposed to a finite number of rigid kinematic joints, can result in greater dexterity without compromising simplicity. One example is the replacement of segmented mechanical legs with simple compliant material eruciform prolegs. To achieve this in robotics, without introducing additional mechanical joints, mobile surfaces with switchable coefficients of friction is essential. This paper explains how, using silicone based smart materials, the rapid alternation between kinematic and static friction (stiction) may be achieved.}, language = {en} } @article{Herrmann, author = {Herrmann, Frank}, title = {Human Experience Versus Rule Decision at Krones AG}, series = {Biomedical Journal of Scientific \& Technical Research}, volume = {42}, journal = {Biomedical Journal of Scientific \& Technical Research}, number = {1}, publisher = {Biomedical Research Network+}, issn = {2574 -1241}, doi = {10.26717/BJSTR.2022.42.006691}, pages = {33255 -- 33260}, abstract = {Final assembly at Krones AG must make the best possible use of its production space and meeting the specified customer due dates is critical. Via a self developed simulation tool, the present scheduling procedure is compared with the one by priority rule shortest slack. As a consequence slack should have a higher importance in the planning}, language = {en} } @article{GoeppelFrikelHaltmeier, author = {G{\"o}ppel, Simon and Frikel, J{\"u}rgen and Haltmeier, Markus}, title = {Data-Proximal Complementary ℓ1-TV Reconstruction for Limited Data Computed Tomography}, series = {Mathematics}, volume = {12}, journal = {Mathematics}, number = {10}, publisher = {MDPI}, issn = {2227-7390}, doi = {10.3390/math12101606}, abstract = {In a number of tomographic applications, data cannot be fully acquired, resulting in severely underdetermined image reconstruction. Conventional methods in such cases lead to reconstructions with significant artifacts. To overcome these artifacts, regularization methods are applied that incorporate additional information. An important example is TV reconstruction, which is known to be efficient in compensating for missing data and reducing reconstruction artifacts. On the other hand, tomographic data are also contaminated by noise, which poses an additional challenge. The use of a single regularizer must therefore account for both the missing data and the noise. A particular regularizer may not be ideal for both tasks. For example, the TV regularizer is a poor choice for noise reduction over multiple scales, in which case ℓ1 curvelet regularization methods are well suited. To address this issue, in this paper, we present a novel variational regularization framework that combines the advantages of different regularizers. The basic idea of our framework is to perform reconstruction in two stages. The first stage is mainly aimed at accurate reconstruction in the presence of noise, and the second stage is aimed at artifact reduction. Both reconstruction stages are connected by a data proximity condition. The proposed method is implemented and tested for limited-view CT using a combined curvelet-TV approach. We define and implement a curvelet transform adapted to the limited-view problem and illustrate the advantages of our approach in numerical experiments.}, language = {en} } @article{HuberHeindlSchlosseretal., author = {Huber, Lea and Heindl, Melanie and Schlosser, Marc and Pfitzner, Arno and Dawoud, Belal}, title = {On the Cycle Stability and Macroscopic Structure of Iron Oxide Pellets for Thermochemical Hydrogen Storage: Influence of Water Content during the Pelletizing Process}, series = {Applied Sciences}, volume = {13}, journal = {Applied Sciences}, number = {11}, publisher = {MDPI}, address = {16}, doi = {10.3390/app13116408}, abstract = {Hydrogen storage based on the repeated reduction and oxidation (redox) reactions of iron oxide/iron composites represents a promising technology. This work is dedicated to studying the influence of the amount of water added during the pelletizing process on the cycle stability and structure of iron oxide pellets. The storage composites were prepared from iron oxide (Fe2O3) and 10 wt.-\% support material (cement) with different amounts of water (18 and 33 wt.-\%) in a laboratory-scale pelletizing disk. To evaluate the cycle stability of the composites, the kinetics of the redox reactions were experimentally measured at 800 ∘ C in an atmosphere of 50\% N2 and 50\% H2 (reduction) or 50\% steam (oxidation), respectively. Moreover, the structure of the pellets was analyzed by micro-computed tomography scans. It turned out that pellets with higher water contents attained faster kinetics and a higher cycle stability. The sample with the least water content (18 wt.-\%) needed about 26 min and 19 min to reach a conversion rate of 80\% during the reduction and oxidation reactions of the sixth redox cycle, respectively. In contrast, the sample with the highest water content (33 wt.-\%) could achieve the same conversion rate after 18 min (reduction) and 13 min (oxidation) during the ninth redox cycle.}, language = {en} } @article{Schiek, author = {Schiek, Roland}, title = {Nonlinear refractive index in silica glass}, series = {Optical Materials Expres}, volume = {13}, journal = {Optical Materials Expres}, number = {6}, publisher = {Optica}, doi = {10.1364/ome.489520}, pages = {1727 -- 1740}, abstract = {The third-order nonlinear susceptibility of silica glass is measured via self-phase modulation in standard single mode fibers at a wavelength of 1550 nm. To minimize the influence of polarization state changes along the propagation only meter-long fibers were investigated. With pulse durations of picoseconds a quasi-instantaneous nonlinearity with ultrafast electronic and fast nuclear-vibration contributions produces under conditions of negligible dispersion a classic and clean nonlinear phase shift following exactly the shape of the pulse power. The complex pulse envelope was retrieved from frequency optical gating spectrograms. The nonlinear fiber parameter γ could be determined with an accuracy of 3.7 percent. Considering the mode field structure and the doping influence the nonlinear refractive index of silica glass as the fiber base material was found to be n 2 =2.22⋅10 -16 cm 2 W±6.0\% for picosecond-long pulses. Comparing nonlinear phase shifts from linear and circular polarized light a nuclear-vibration contribution to the cubic fiber nonlinearity of 25 percent was estimated.}, language = {en} } @article{SteiningerGadererDawoud, author = {Steininger, Peter and Gaderer, Matthias and Dawoud, Belal}, title = {Assessment of the Annual Transmission Heat Loss Reduction of a Refurbished Existing Building with an Advanced Solar Selective Thermal Insulation System}, series = {Sustainability}, volume = {13}, journal = {Sustainability}, number = {13}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/su13137336}, pages = {1 -- 19}, abstract = {A numerical parameter sensitivity analysis of the design parameters of the recently published solar selective thermal insulation system (SATIS) has been carried out to enhance its thermal and optical properties. It turned out that the insulation properties of SATIS can be effectively improved by reducing the length of the glass closure element. Increasing the area share of the light conducting elements (LCEs) and decreasing their length-to-diameter (L/D) ratio were identified as key parameters in order to increase the solar gain. Two SATIS variants were compared with the same wall insulation without SATIS in a yearly energetic performance assessment. The SATIS variant with 10 mm length of the closure element, 44.2\% area share of LCE, as well as front and rear diameters of 12 mm/9 mm shows an 11.8\% lower transmission heat loss over the heating period than the wall insulation without SATIS. A new methodology was developed to enable the implementation of the computed solar gains of SATIS in 1D simulation tools. The result is a radiant heat flow map for integration as a heat source in 1D simulation models. A comparison between the 1D and 3D models of the inside wall heat fluxes showed an integral yearly agreement of 98\%.}, language = {en} } @article{SaidEngelhartKirchesetal., author = {Said, Nadia and Engelhart, Michael and Kirches, Christian and K{\"o}rkel, Stefan and Holt, Daniel V.}, title = {Applying mathematical optimization methods to an ACT-R instance-based learning model}, series = {PLoS ONE}, volume = {11}, journal = {PLoS ONE}, number = {7}, publisher = {PLOS}, doi = {10.1371/journal.pone.0158832}, abstract = {Computational models of cognition provide an interface to connect advanced mathematical tools and methods to empirically supported theories of behavior in psychology, cognitive science, and neuroscience. In this article, we consider a computational model of instance-based learning, implemented in the ACT-R cognitive architecture. We propose an approach for obtaining mathematical reformulations of such cognitive models that improve their computational tractability. For the well-established Sugar Factory dynamic decision making task, we conduct a simulation study to analyze central model parameters. We show how mathematical optimization techniques can be applied to efficiently identify optimal parameter values with respect to different optimization goals. Beyond these methodological contributions, our analysis reveals the sensitivity of this particular task with respect to initial settings and yields new insights into how average human performance deviates from potential optimal performance. We conclude by discussing possible extensions of our approach as well as future steps towards applying more powerful derivative-based optimization methods.}, language = {en} } @article{SindersbergerPremMonkman, author = {Sindersberger, Dirk and Prem, Nina and Monkman, Gareth J.}, title = {Structure formation in low concentration magnetoactive polymers}, series = {AIP advances}, volume = {9}, journal = {AIP advances}, number = {3}, publisher = {AIP Publishing}, doi = {10.1063/1.5079997}, abstract = {This paper concerns recent research into the autonomous formation of micro-structures in low carbonyl iron powder (CIP) concentration magneto active polymers (MAP). Higher concentrations of CIP show an isotropic distribution of magnetic filler throughout the entire sample, while autonomous structure formation is possible at mass concentrations lower than 3\%. The formation of micro-toroids commences as CIP concentration approaches 1\% wt. Further development of coherent rings with a defined order follow as CIP concentrations increase toward 2\% wt, whilst exceeding 3\% wt leads to the same isotropic distribution found in higher concentration MAP. Structured samples containing between 1\% wt and 3\% wt CIP were investigated using X-Ray tomography where solitary structures could clearly be observed. The ring structures represent microinductivities whose geometries can be manipulated during fabrication. In addition, these structures are magnetic field sensitive. This is not only relevant to applications in the GHz and THz areas but recent research has revealed implications for optical, thermal, acoustic and even chemical MAP sensors. (C) 2019 Author(s).}, language = {en} } @article{FrazzicaBrancatoDawoud, author = {Frazzica, Andrea and Brancato, Vincenza and Dawoud, Belal}, title = {Unified Methodology to Identify the Potential Application of Seasonal Sorption Storage Technology}, series = {Energies}, volume = {13}, journal = {Energies}, number = {5}, publisher = {MPDI}, address = {Basel}, doi = {10.3390/en13051037}, pages = {1 -- 17}, abstract = {In this study, the definition of a new methodology for a preliminary evaluation of the working boundary conditions under which a seasonal thermal energy storage (STES) system operates is described. The approach starts by considering the building features as well as the reference heating system in terms of solar thermal collectors' technology, ambient heat sinks/source, and space heating distribution systems employed. Furthermore, it is based on a deep climatic analysis of the place where the STES needs to be installed, to identify both winter and summer operating conditions. In particular, the STES energy density is evaluated considering different space heating demands covered by the STES (ranging from 10\% up to 60\%). The obtained results demonstrate that this approach allows for the careful estimation of the achievable STES density, which is varies significantly both with the space heating coverage guaranteed by the STES as well as with the ambient heat source/sink that is employed in the system. This confirms the need for careful preliminary analysis to avoid the overestimation of the STES material volume. The proposed approach was then applied for different climatic conditions (e.g., Germany and Sweden) and the volume of one of the most attractive composite sorbent materials reported in the literature, i.e., multi-wall carbon nanotubes (MWCNT)-LiCl, using water as the working fluid, needed for covering the variable space heating demand in a Nearly Zero Energy Building (NZEB) was calculated. In the case of Swedish buildings, it ranges from about 3.5 m3 when 10\% of the space heating demand is provided by the STES, up to 11.1 m3 when 30\% of the space heating demand is provided by the STES.}, language = {en} } @article{HagerSeitzWaas, author = {Hager, Markus and Seitz, Jochen and Waas, Thomas}, title = {Literature Survey on Recent Progress in Inter-Vehicle Communication Simulations}, series = {Journal of Transportation Technologies}, volume = {Vol. 5}, journal = {Journal of Transportation Technologies}, number = {3}, doi = {10.4236/jtts.2015.53015}, pages = {159 -- 168}, abstract = {The vehicular ad hoc network (VANET) technology based on the approved IEEE 802.11p standard and the appendant inter-vehicle communication (IVC) has the potential to dramatically change the way transportation systems work. The fundamental idea is to change the individual behavior of each vehicle by exchanging information among traffic participants to realize a cooperative and more efficient ransportation system. Certainly, the evaluation of such systems is a comprehensive and challenging task in a real world test bed, therefore, simulation frameworks are a key tool to analyze IVC. Several models are needed to emulate the real behavior of a VANET in all aspects as much realistically as necessary. The intention of this survey is to provide a comprehensive overview of publications concerning IVC simulations of the year 2013 and to see how IVC simulation has changed since 2009. Based on this analysis, we will answer the following questions: What simulation techniques are applied to IVC? Which aspects of IVS have been evaluated? What has changed within five years of IVC simulations? We also take a closer look at commonly used software tools and discuss their functionality and drawbacks. Finally, we present open questions concerning IVC simulations.}, language = {en} } @article{WeberHuberBorchseniusetal.2020, author = {Weber, Felix and Huber, Peter and Borchsenius, Fredrik and Braun, Christian}, title = {Performance of TMDI for Tall Building Damping}, series = {Actuators}, volume = {9}, journal = {Actuators}, number = {4}, publisher = {MPDI}, doi = {10.3390/act9040139}, pages = {1 -- 13}, year = {2020}, abstract = {This study investigates the vibration reduction of tall wind-excited buildings using a tuned mass damper (TMD) with an inerter (TMDI). The performance of the TMDI is computed as a function of the floor to which the inerter is grounded as this parameter strongly influences the vibration reduction of the building and for the case when the inerter is grounded to the earth whereby the absolute acceleration of the corresponding inerter terminal is zero. Simulations are made for broadband and harmonic excitations of the first three bending modes, and the conventional TMD is used as a benchmark. It is found that the inerter performs best when grounded to the earth because, then, the inerter force is in proportion to the absolute acceleration of only the pendulum mass, but not to the relative acceleration of the two inerter terminals, which is demonstrated by the mass matrix. However, if the inerter is grounded to a floor below the pendulum mass, the TMDI only outperforms the TMD if the inerter is grounded to a floor within approximately the first third of the building's height. For the most realistic case, where the inerter is grounded to a floor in the vicinity of the pendulum mass, the TMDI performs far worse than the classical TMD.}, language = {en} } @article{AbhijitSenBaumgartnerHeissetal., author = {Abhijit Sen, Kwantlen and Baumgartner, Laura and Heiß, Katharina and Wagner, Cornelia}, title = {DevOps paradigm}, series = {Issues in Information Systems}, volume = {22}, journal = {Issues in Information Systems}, number = {4}, publisher = {International Association for Computer Information Systems}, issn = {1529-7314}, doi = {10.48009/4_iis_2021_117-133}, pages = {110 -- 125}, abstract = {DevOps, the widely used term in software industry, integrates the Development and IT Operations activities to frequently deliver, deploy, and release quality software features. DevOps approach emphasizes collaboration among Developments and IT operations teams throughout System Development Life Cycle (SDLC). The DevOps process is supported by wide variety of tool chains for various phases of SDLC. There exist many DevOps models. However, in this paper authors use a simple four phase pedagogical models to demonstrate principles of DevOps. In this paper authors attempt to show how DevOps principles can effectively be used to manage and implement business problems in classroom setting. Specifically, DevOps methodology is applied to manage develop and implement a small web application. This pedagogical approach is specially aimed at students who do not have prior experiences and skillsets in applying DevOps methodology and associated toolsets to every stages of SDLC. At the conclusion of the project, students gained valuable insights on how to apply DevOps principles to business problems and to select and use commonly used state of the arts tools to plan, manage, build, test, monitor, deploy tasks at every stages of DevOps. The authors also discuss the limitations and practical issues related to implementing DevOps within classroom settings.}, language = {en} }