@inproceedings{KnappLangerPrommesbergeretal., author = {Knapp, Wolfram and Langer, Christoph and Prommesberger, Christian and Lindner, Matthias and Schreiner, Rupert}, title = {Investigations of the transition from field electron emission to stable plasma discharge in a micro electron source at vacuum pressure}, series = {2017 30th International Vacuum Nanoelectronics Conference (IVNC), 10-14 July 2017, Regensburg, Germany}, booktitle = {2017 30th International Vacuum Nanoelectronics Conference (IVNC), 10-14 July 2017, Regensburg, Germany}, publisher = {IEEE}, doi = {10.1109/IVNC.2017.8051594}, pages = {166 -- 167}, abstract = {We report on the transition from field electron emission to plasma discharges. During an experiment with a miniaturized field emission electron source a plasma discharge accompanied by a luminous effect was observed. A novel graphical evaluation method was used to interpret and to compare the observed phenomenon.}, language = {en} } @inproceedings{PrommesbergerLangerŁawrowskietal., author = {Prommesberger, Christian and Langer, Christoph and Ławrowski, Robert Damian and Muller, F. and Dams, Florian and Schreiner, Rupert and Serbun, Pavel and M{\"u}ller, G{\"u}nter}, title = {Comparison of integral and local field-emission properties of Mo-coated p-Si tip arrays}, series = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, booktitle = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, publisher = {IEEE}, doi = {10.1109/IVNC.2015.7225579}, pages = {192 -- 193}, abstract = {Silicon tip arrays were fabricated by means of reactive ion etching followed by oxidation for final sharpening and molybdenum thin film coating. The field-emission (FE) properties of these Mo-coated p-Si tip arrays were systemically investigated by different measurement techniques. Integral measurements in diode configuration yielded a turn-on field (for 1 nA) of 22 V/μm and nearly stable FE currents up to 6.6 μA at 38 V/μm. The effective field enhancements factor extracted from the FN plots is about 180. Detailed investigations of these FE arrays were also performed by means of field emission scanning microscopy combined with electron microscopy. A rather limited efficiency of the tips (50\% at 1500 V) and FE homogeneity (180 nA at 700 V) might be correlated with the varying morphology of the tips and the presence of oxides. Local I-V measurements of selected single tips revealed both activation and deactivation effects, which finally resulted in nearly reproducible I-V curves. Current stability measurements at a constant voltage showed rather large fluctuations (0.1-1 μA) of the FE current, which could be reduced up to 1.7\% by using of a PID-regulated voltage source. SEM images showed unchanged tip shape after the current processing.}, language = {en} } @inproceedings{ŁawrowskiLangerPrommesbergeretal., author = {Ławrowski, Robert Damian and Langer, Christoph and Prommesberger, Christian and Dams, Florian and Bachmann, Michael and Schreiner, Rupert}, title = {Fabrication and simulation of silicon structures with high aspect ratio for field emission devices}, series = {2014 27th International Vacuum Nanoelectronics Conference (IVNC), 6-10 July 2014, Engelberg, Switzerland}, booktitle = {2014 27th International Vacuum Nanoelectronics Conference (IVNC), 6-10 July 2014, Engelberg, Switzerland}, publisher = {IEEE}, doi = {10.1109/IVNC.2014.6894805}, pages = {193 -- 194}, abstract = {To obtain higher field enhancement factors of Si-tip structures, we present an improved fabrication process utilizing reactive-ion etching (RIE) with an inductively coupled plasma (ICP). In our design, a pillar under the tips is realized by a combination of RIE with ICP. With adjusted power settings (≈ 240 W) and step times (<; 5 s), vertical slopes with a low roughness of approximately 10 nm to 20 nm are possible. The remaining silicon is oxidized thermally to sharpen the emitters. A final tip radius of R <; 20 nm is obtained for the tips of the emitters. The pillar height HP can be mainly adjusted by the duration of the ICP-etching step. A total emitter height of H ≈ 6 μm with a pillar height of HP ≈ 5 μm is achieved. Simulations with COMSOL Multiphysics® are applied to calculate the field enhancement factor β. A two-dimensional model is used in rotational symmetry. In addition to the previous model, a pillar with a varying diameter {\O}P and height HP is added. A conventional emitter (H = 1 μm and R = 20 nm) placed on a pillar of the height HP ≈ 5 μm approximately results in a three times higher β-factor (β≈ 105). By decreasing the diameter {\O}P a slight increase of the β-factor is observed. However, the aspect ratio of the emitter mainly influences on the β-factor.}, language = {en} }