@article{RillSchuderer, author = {Rill, Georg and Schuderer, Matthias}, title = {A Second-Order Dynamic Friction Model Compared to Commercial Stick-Slip Models}, series = {Modelling}, volume = {4}, journal = {Modelling}, number = {3}, publisher = {MDPI}, issn = {2673-3951}, doi = {10.3390/modelling4030021}, pages = {366 -- 381}, abstract = {Friction has long been an important issue in multibody dynamics. Static friction models apply appropriate regularization techniques to convert the stick inequality and the non-smooth stick-slip transition of Coulomb's approach into a continuous and smooth function of the sliding velocity. However, a regularized friction force is not able to maintain long-term stick. That is why dynamic friction models were developed in recent decades. The friction force depends herein not only on the sliding velocity but also on internal states. The probably best-known representative, the LuGre friction model, is based on a fictitious bristle but realizes a too-simple approximation. The recently published second-order dynamic friction model describes the dynamics of a fictitious bristle more accurately. It is based on a regularized friction force characteristic, which is continuous and smooth but can maintain long-term stick due to an appropriate shift in the regularization. Its performance is compared here to stick-slip friction models, developed and launched not long ago by commercial multibody software packages. The results obtained by a virtual friction test-bench and by a more practical festoon cable system are very promising. Thus, the second-order dynamic friction model may serve not only as an alternative to the LuGre model but also to commercial stick-slip models.}, language = {en} } @unpublished{RillSchuderer, author = {Rill, Georg and Schuderer, Matthias}, title = {A Second Order Dynamic Friction Model Compared to Commercial Stick-Slip Models}, doi = {10.20944/preprints202306.1233.v1}, abstract = {Friction has long been an important issue in multibody dynamics. Static friction models apply appropriate regularization techniques to convert the stick inequality and the non-smooth stick-slip transition of Coulomb's approach into a continuous and smooth function of the sliding velocity. However, a regularized friction force is not able to maintain long-term stick. That is why, dynamic friction models were developed in the last decades. The friction force depends herein not only on the sliding velocity but also on internal states. The probably best known representative, the LuGre friction model, is based on a fictitious bristle but realizes a too simple approximation. The recently published second order dynamic friction model describes the dynamics of a fictitious bristle more accurately. Its performance is compared here to stick-slip friction models, developed and launched not long ago by commercial multibody software packages.}, language = {en} } @article{SchudererRillSchaefferetal., author = {Schuderer, Matthias and Rill, Georg and Schaeffer, Thomas and Schulz, Carsten}, title = {Friction modeling from a practical point of view}, series = {Multibody System Dynamics}, journal = {Multibody System Dynamics}, publisher = {Springernature}, issn = {1384-5640}, doi = {10.1007/s11044-024-09978-0}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-72513}, pages = {18}, abstract = {AbstractRegularized static friction models have been used successfully for many years. However, they are unable to maintain static friction in detail. For this reason, dynamic friction models have been developed and published in the literature. However, commercial multibody simulation packages such as Adams, RecurDyn, and Simpack have developed their own specific stick-slip models instead of adopting one of the public domain approaches. This article introduces the fundamentals of these commercial models and their behavior from a practical point of view. The stick-slip models were applied to a simple test model and a more sophisticated model of a festoon cable system using their standard parameters.}, language = {en} } @unpublished{RillSchaefferSchuderer, author = {Rill, Georg and Schaeffer, Thomas and Schuderer, Matthias}, title = {LuGre or not LuGre}, doi = {10.21203/rs.3.rs-2266522/v1}, abstract = {The LuGre model is widely used in the analysis and control of systems with friction. Recently, it has even been made available in the commercial multibody dynamics simulation software system Adams. However, the LuGre model exhibits well-known drawbacks like, too low and force rate dependent break-away forces, drift problems during sticking periods, and significant differences in non-stationary situations between the pre-defined friction law and the one produced by the LuGre model. In the present literature, these problems are supposed to come from the model dynamics or its nonlinear nature. However, most of these drawbacks are not simple side effects of a dynamic friction model but are caused in the LuGre approach, as shown here, by a too simple and inconsistent model of the bristle dynamics. Standard examples and a more practical application demonstrate, that the LuGre model is not a "what you see is what you get" approach. A dynamic friction model with accurate bristle dynamics and consistent friction force is set up here. It provides insight into the physical basis of the LuGre model dynamics. However, it results in a nonlinear and implicit differential equation, whose solution will not be easy because of the ambiguity of the friction characteristics. The standard workaround, a static model based on a simple regularized characteristics, produces reliable and generally satisfactory results, but definitely cannot maintain stick. The paper presents a second order dynamic friction model, which may serve as an alternative. It can maintain stick and produces realistic and reliable results.}, language = {en} } @article{RillSchaefferSchuderer, author = {Rill, Georg and Schaeffer, Thomas and Schuderer, Matthias}, title = {LuGre or not LuGre}, series = {Multibody System Dynamics}, journal = {Multibody System Dynamics}, publisher = {Springer}, doi = {10.1007/s11044-023-09909-5}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-65653}, pages = {28}, abstract = {The LuGre model is widely used in the analysis and control of systems with friction. Recently, it has even been made available in the commercial multibody dynamics simulation software system Adams. However, the LuGre model exhibits well-known drawbacks like too low and force rate-dependent break-away forces, drift problems during sticking periods, and significant differences in non-stationary situations between the pre-defined friction law and the one produced by the LuGre model. In the present literature, these problems are supposed to come from the model dynamics or its nonlinear nature. However, most of these drawbacks are not simple side effects of a dynamic friction model but are caused in the LuGre approach, as shown here, by a too simple and inconsistent model of the bristle dynamics. Standard examples and a more practical application demonstrate that the LuGre model is not a "what you see is what you get" approach. A dynamic friction model with accurate bristle dynamics and consistent friction force is set up here. It provides insight into the physical basis of the LuGre model dynamics. However, it results in a nonlinear and implicit differential equation, whose solution will not be easy because of the ambiguity of the friction characteristics. The standard workaround, a static model based on simple regularized characteristics, produces reliable and generally satisfactory results but definitely cannot maintain a stick. The paper presents a second-order dynamic friction model, which may serve as an alternative. It can maintain a stick and produces realistic and reliable results.}, language = {en} } @misc{SchudererRillSchaefferetal., author = {Schuderer, Matthias and Rill, Georg and Schaeffer, Thomas and Schulz, Carsten}, title = {Friction modeling from a practical point of view}, series = {MULTIBODY2023: 11th ECCOMAS Thematic Conference on Multibody Dynamics, Tampa, 24th-28th May 2023}, journal = {MULTIBODY2023: 11th ECCOMAS Thematic Conference on Multibody Dynamics, Tampa, 24th-28th May 2023}, language = {en} }