@article{SerbunBornmannNavitskietal., author = {Serbun, Pavel and Bornmann, Benjamin and Navitski, Aliaksandr and M{\"u}ller, G{\"u}nter and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Stable field emission of single B-doped Si tips and linear current scaling of uniform tip arrays for integrated vacuum microelectronic devices}, series = {Journal of Vacuum Science \& Technology B Nanotechnology and Microelectronics}, volume = {31}, journal = {Journal of Vacuum Science \& Technology B Nanotechnology and Microelectronics}, number = {2}, publisher = {AIP Publishing}, doi = {10.1116/1.4765088}, abstract = {Advanced Si-based semiconductor technology is most suitable to fabricate uniform nanostructures as integrated field emitter arrays for novel vacuum electronic devices. In order to improve the field emission homogeneity and stability of p-type silicon tip arrays for pulsed sensor applications, the authors have systematically studied the influence of the fabrication parameters on the tip shape and on the specific operating conditions. Based on detailed design calculations of the field enhancement, they have fabricated two series of hexagonal arrays of B-doped Si-tips in a triangular arrangement. The first (second) type contains three (four) patches with different number of tips (1, 91, 547 and 1, 19, 1027, 4447 for the first and second type, respectively) of about 1 (2.5) μm height, ∼20 (20) nm apex radius, and 20 (10) μm pitch. The field emission properties of both individual tips and complete arrays were investigated with a field emission scanning microscope at a pressure of 10-9 mbar. The current plateau of these tips typically occurs at about 10 (3) nA and around 65 (25) V/μm field level. In this carrier saturation range, single tips provide the highest current stability (<5\%) and optical current switching ratio (∼2.5). Fairly homogeneous emission of the tip arrays leads to an undershooting of the expected linear scaling of the mean plateau current as well as to a much improved current stability (<1\%).}, language = {en} } @article{SchelsEdlerHerdletal., author = {Schels, Andreas and Edler, Simon and Herdl, Florian and Hansch, Walter and Bachmann, Michael and Ritter, Daniela and Dudeck, Markus and Duesberg, Felix and Meyer, Manuel and Pahlke, Andreas and Hausladen, Matthias and Buchner, Philipp and Schreiner, Rupert}, title = {In situ quantitative field emission imaging using a low-cost CMOS imaging sensor}, series = {Journal of Vacuum Science \& Technology B}, volume = {40}, journal = {Journal of Vacuum Science \& Technology B}, number = {1}, publisher = {AIP Publishing}, doi = {10.1116/6.0001551}, abstract = {Spatially resolved field emission measurements represent an important factor in further development of existing field emitter concepts. In this work, we present a novel approach that allows quantitative analysis of individual emission spots from integral current-voltage measurements using a low-cost and commercially available CMOS camera. By combining different exposure times to extrapolate oversaturated and underexposed pixels, a near congruence of integral current and image brightness is shown. The extrapolation also allows parallel investigation of all individual tips participating in the total current with currents ranging from a few nanoampere to one microampere per tip. The sensitivity, which is determined by the integral brightness-to-current ratio, remains unchanged within the measurement accuracy even after ten full measurement cycles. Using a point detection algorithm, the proportional current load of each individual tip of the field emitter array is analyzed and compared at different times during the initial measurement cycle. Together with the extracted I-V curves of single emission spots from the integral measurement, the results indicate the effect of premature burnout of particularly sharp tips during conditioning of the emitter.}, language = {en} } @article{EdlerSchelsHerdletal., author = {Edler, Simon and Schels, Andreas and Herdl, Florian and Hansch, Walter and Bachmann, Michael and Dudeck, Markus and Duesberg, Felix and Pahlke, Andreas and Hausladen, Matthias and Buchner Philipp, and Schreiner, Rupert}, title = {Origin of the current saturation level of p-doped silicon field emitters}, series = {Journal of Vacuum Science \& Technology B}, volume = {40}, journal = {Journal of Vacuum Science \& Technology B}, number = {1}, publisher = {AIP Publishing}, doi = {10.1116/6.0001554}, abstract = {Using p-type semiconductors for field emitters is one simple way to realize an integrated current limiter to improve the lifetime of the cathode. In this work, the origin of the current saturation of p-type silicon emitters is investigated in detail. Single emitters are electrically characterized and compared to simulation results. With a simulation model considering a high surface generation rate and elevated tip temperature, a good agreement to the measured data is found. This observation is supported further by alteration of the surface experimentally. Electrical measurements after different treatments in hydrofluoric acid as well as heated and subsequent operation at room temperature are well explained by the influence of surface generation. Furthermore, it is shown that the field penetration leads to a small voltage drop and a strong geometry-dependent reduction of the field enhancement factor.}, language = {en} } @inproceedings{TschurtschenthalerKrenkelSchreiner, author = {Tschurtschenthaler, Karl and Krenkel, Lars and Schreiner, Rupert}, title = {Mechano-optical micro pillar sensor for biofluidmechanic wall shear stress measurements}, series = {25th Congress of the European Society of Biomechanics (ESB), July 7-10, 2019, Vienna, Austria}, booktitle = {25th Congress of the European Society of Biomechanics (ESB), July 7-10, 2019, Vienna, Austria}, language = {en} } @article{BiekerRoustaieSchlaaketal., author = {Bieker, Johannes and Roustaie, Farough and Schlaak, Helmut F. and Langer, Christoph and Schreiner, Rupert and Lotz, Marcel and Wilfert, Stefan}, title = {Field emission characterization of in situ deposited gold nanocones with variable cone densities}, series = {Journal of Vacuum Science and Technology B}, volume = {36}, journal = {Journal of Vacuum Science and Technology B}, number = {2}, publisher = {AIP Publishing}, doi = {10.1116/1.5009504}, abstract = {For the fabrication of field emitter cathodes with metallic nanocones, an in situ fabrication technique based on electrodeposition in an ion track etched polymer template was used. Three samples with nanocones made of gold and different cone densities were deposited on a circular electrode with a diameter of 2.5 mm, using templates with pore density of 6 × 104, 4 × 105, and 1 × 106 cones/cm2. The cones had a height of 24 μm, a base diameter between 3 and 3.75 μm, and a tip diameter below 500 nm. Integral field emission measurements revealed onset fields of down to 3.1 V/μm and average field enhancement factors of up to 1240. For one sample, the maximum emission current from the cathode reached 142.2 μA at an applied voltage of 338 V between cathode and extraction grid, which had a distance of 50 μm. To investigate the stability of the field emission current, cumulative long-term measurements were performed for over 50 h. A stable emission current of (31.0 ± 1.3) μA at an average applied voltage of 290 V (E = 5.8 V/μm) was observed. For currents above 100 μA, a decrease of the current and therefore a degradation of the emitter structures occurred.}, language = {en} } @inproceedings{DamsSchreiner, author = {Dams, Florian and Schreiner, Rupert}, title = {A high thermal resistance MEMS-based Pirani vacuum sensor chip}, series = {Smart sensors, actuators and MEMS VI : 24 - 26 April 2013, Grenoble, France / [part of SPIE microtechnologies]}, booktitle = {Smart sensors, actuators and MEMS VI : 24 - 26 April 2013, Grenoble, France / [part of SPIE microtechnologies]}, publisher = {SPIE}, address = {Bellingham, Wash.}, doi = {10.1117/12.2017345}, abstract = {The performance of thermal conductivity vacuum gauges can be improved by a well-designed geometry. The lower measurement range limit is determined by the size of the active sensing area and the thermal conduction heat losses through the supporting structures. The upper measurement range is limited by the distance between the heated element and the cold reference plane. Silicon based MEMS-technology gives the possibility to fabricate both sensing structures with suitable areas out of low thermal conductive materials and narrow gaps in order to extend the measurement range in both directions. In this work we present a MEMS-process to fabricate high thermal resistance sensor structures. The rectangular sensitive areas are anchored by four beams and are structured out of low thermal conductive PECVD-siliconnitride films with 1 µm in thickness. The metallic heating structure is completely embedded in the SiN-layer. Both sensitive area and its support beams were released from the silicon bulk material by anisotropic underetching. In this way a free-supporting structure with a gap of 150 μm to the silicon substrate was formed. The influence of the filament geometry and temperature was systematically investigated to determine the properties of the chips as thermal conductivity vacuum gauges. The temperature of the sensitive area was held constant by a self-balancing bridge circuit and the heating power was measured by a Δ-Σ-ADC. The average solid state thermal conductivity is in the order of 106WK1. The measuring range of the most sensitive structures covers 8 orders of magnitude from 105 mbar to 1000mbar.}, language = {en} } @misc{DuesbergBachmannEdleretal., author = {D{\"u}sberg, Felix and Bachmann, Michael and Edler, Simon and Pahlke, Andreas and Langer, Christoph and Prommesberger, Christian and Schreiner, Rupert and Bunert, Erik and Wendt, Cornelius and Zimmermann, Stefan}, title = {Novel Non-Radiative Electron Source}, series = {43rd International Symposium of Capillary Chromatography \& 16h GC x GC Symposium 2019}, journal = {43rd International Symposium of Capillary Chromatography \& 16h GC x GC Symposium 2019}, abstract = {Recently a non-radioactive electron capture detector based on a thermionic electron emitter has been demonstrated [1]. Using field emitter arrays (FEAs) would yield non-radioactive portable low power devices with fast switching capability. By combining FEAs with a vacuum-sealed housing and an electron transparent membrane window, such electron sources can be operated in an ambient pressure environment.}, language = {en} } @inproceedings{BerndtLindnerSchreineretal., author = {Berndt, Dominik and Lindner, Matthias and Schreiner, Rupert and Pipa, Andrei V. and Hink, R{\"u}diger and Brandenburg, Ronny and Foest, R{\"u}diger and Geils, Judith and Sander, Aljoscha and Hoffmann, Florian and Matz, Daniel and Baars, Albert and Kesel, Antonia and Max, Alexander and Caspari, Ralf}, title = {Realization of Multifunctional Surfaces Containing MEMS-based DBD Plasma Actuators and Biomimetic Structures for Flow Manipulation}, series = {AIAA Aviation 2019 Forum, 2019, Dallas}, booktitle = {AIAA Aviation 2019 Forum, 2019, Dallas}, publisher = {American Institute of Aeronautics and Astronautics, Inc}, doi = {10.2514/6.2019-2999}, language = {en} } @inproceedings{PrommesbergerLangerSchreiner, author = {Prommesberger, Christian and Langer, Christoph and Schreiner, Rupert}, title = {Stable and low noise field emission from single p-type Si-tips}, series = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, booktitle = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, publisher = {IEEE}, doi = {10.1109/IVNC.2018.8520018}, pages = {1-2}, abstract = {Single gated p-type Si-tips with two different tip radii were fabricated. An emission current of 2.40 μA was measured for the sharp-edged tip at a voltage of 170 V. In contrast, a stable and reproducible emission behavior was observed with an increased tip radius resulting in a pronounced saturation region between 90 V and 150 V, but merely an emission current of 0.55 μA at 150 V. More remarkable is the stable emission behavior with fluctuation of ± 4 \% during a measurement period of 30 minutes. The integral emission current in a homogeneous tip array (16 emitters) showed nearly the same I-V characteristics compared to the single tip and is therefore, most dominated by only a stable single tip in the array.}, language = {en} } @inproceedings{LindnerBerndtPrommesbergeretal., author = {Lindner, Matthias and Berndt, Dominik and Prommesberger, Christian and Langer, Christoph and Schreiner, Rupert}, title = {Field emission assisted micro plasma discharges at vacuum and atmospheric pressures}, series = {31st International Vacuum Nanoelectronics Conference (IVNC), 2018, Kyoto, Japan}, booktitle = {31st International Vacuum Nanoelectronics Conference (IVNC), 2018, Kyoto, Japan}, doi = {10.1109/IVNC.2018.8520181}, pages = {2}, abstract = {Spatially confined non-equilibrium plasmas at vacuum and atmospheric pressure in the dimensions from a few microns to one millimeter are a promising approach to the generation and maintenance of stable glow discharges. The realization of these micro-discharges or micro-plasmas enable more accurate investigations in the field of micro plasma research. We report on field emission assisted micro plasmas excited by an alternating current with frequencies up to 1 kHz. Due to the field enhancement caused by an array of Si nano-tip structures the ignition voltage of stable plasma discharges can be reduced by 30\%.}, language = {en} } @inproceedings{BerndtLindnerTschurtschenthaleretal., author = {Berndt, Dominik and Lindner, Matthias and Tschurtschenthaler, Karl and Langer, Christoph and Schreiner, Rupert}, title = {Miniaturized Plasma Actuator Flow Measurements by MEMS-Based Thermal Conductivity Sensors}, series = {MDPI Proceedings of Eurosensors 2018, 9-12 September, Graz}, volume = {Vol.13}, booktitle = {MDPI Proceedings of Eurosensors 2018, 9-12 September, Graz}, number = {2}, doi = {10.3390/proceedings2130939}, abstract = {The gasflow created by a minaturized dielectric barrier discharge (DBD) plasma actuator is measured by a MEMS-based thermal conductivity gas sensor giving an indication of flow velocity and flow direction. The possiblity of several sensors in a small area gives a far better accuracy of local flow phenomena compared to conventional sensors. This is important for a better understanding of plasma- induced flow characteristics.}, language = {en} } @inproceedings{EdlerHanschPrommesbergeretal., author = {Edler, Simon and Hansch, Walter and Prommesberger, Christian and Schreiner, Rupert}, title = {Influence of adsorbates on the performance of a field emitter array in a high voltage triode setup}, series = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, booktitle = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, publisher = {IEEE}, doi = {10.1109/IVNC.2018.8520214}, pages = {1-2}, abstract = {The influence of residual gas pressure on the characteristics of black-Silicon field emitter arrays in a high voltage triode setup is investigated. I-Vcharacteristics at different pressure levels show a decrease of emission current with rising pressure. This can be explained by an increase of the work function and charging of the emitter surface due to adsorbates. The initial characteristics can be restored by heating the FEA up to 110 °C during electron emission. This regeneration procedure enables an extension of the lifetime from about 20 h to 440 h at a residual gas pressure of 10 -5 mbar.}, language = {en} } @article{BerndtMuggliWittweretal., author = {Berndt, Dominik and Muggli, Josef and Wittwer, Franz and Langer, Christoph and Heinrich, Stephan and Knittel, Thorsten and Schreiner, Rupert}, title = {MEMS-based thermal conductivity sensor for hydrogen gas detection in automotive applications}, series = {Sensors and Actuators A: Physical}, volume = {305}, journal = {Sensors and Actuators A: Physical}, number = {April}, publisher = {Elsevier}, doi = {10.1016/j.sna.2019.111670}, abstract = {Accurate detection of hydrogen gas in vehicle interiors is very important for the future of a fuel cell car. Since this type of gas is highly volatile and flammable, the measurement methods have to be very reliable and precise due to safety reasons. In this paper a thermal conductivity sensor for hydrogen gas detection is presented, exhibiting a lower detection limit of 2000 ppm hydrogen in laboratory air. The sensor element is realized by micro-fabrication techniques on silicon wafers. The heated filament is exposed by a selective wet etching process creating a micro-hotplate on a thin membrane. In order to minimize power consumption, the sensor is operated in pulsed mode. Hydrogen gas detection was carried out using a synthetic gas testbench. Measurements of hydrogen contents ranging from 0\% to 4\% with an increment of 0.5\% were successfully performed for ambient gas temperatures between -15°C and 84°C. Including humidity, high moisture contents have the greatest influence on thermal conductivity. This was predicted in theoretical investigations and confirmed in experiments. For evaluation, both the change in resistance ΔR as well as the time constant τ were taken as sensor output. For both quantities, the previously established theoretical relationship with thermal conductivity could be confirmed.}, language = {en} } @inproceedings{SilberbauerLindnerSchreiner, author = {Silberbauer, Theodor and Lindner, Matthias and Schreiner, Rupert}, title = {Charakterisierung der dielektrischen Barrierenentladung von Mikroplasmaaktuatoren in Abh{\"a}ngigkeit der Substratdicke}, series = {Intelligente Systeme und ihre Komponenten: Forschung und industrielle Anwendung : Fachbeitr{\"a}ge 2. Symposium Elektronik und Systemintegration ESI 2020}, booktitle = {Intelligente Systeme und ihre Komponenten: Forschung und industrielle Anwendung : Fachbeitr{\"a}ge 2. Symposium Elektronik und Systemintegration ESI 2020}, address = {Landshut}, pages = {64 -- 72}, language = {de} } @article{KrysztofMieraUrbańskietal., author = {Krysztof, Michał and Miera, Paweł and Urbański, Paweł and Grzebyk, Tomasz and Hausladen, Matthias and Schreiner, Rupert}, title = {Integrated silicon electron source for high vacuum microelectromechanical system devices}, series = {Journal of Vacuum Science \& Technology B}, volume = {42}, journal = {Journal of Vacuum Science \& Technology B}, number = {2}, publisher = {AIP Publishing}, issn = {2166-2746}, doi = {10.1116/6.0003385}, abstract = {The article presents the process of developing a silicon electron source designed for high-vacuum microelectromechanical system (HV MEMS) devices, i.e., MEMS electron microscope and MEMS x-ray source. Technological constraints and issues of such an electron source are explained. The transition from emitters made of carbon nanotubes to emitters made of pure silicon is described. Overall, the final electron source consists of a silicon tip emitter and a silicon gate electrode integrated on the same glass substrate. The source generates an electron beam without any carbon nanotube coverage. It generates a high and stable electron current and works after the final bonding process of an HV MEMS device.}, language = {en} } @article{SchreinerNaegeleKoerbletal., author = {Schreiner, Rupert and Naegele, Peter and K{\"o}rbl, M. and Groning, A. and Gentner, Jean-Louis and Schweizer, Heinz C.}, title = {Monolithically integrated tunable laterally coupled distributed-feedback lasers}, series = {Photonics Technology Letters}, volume = {13}, journal = {Photonics Technology Letters}, number = {12}, publisher = {IEEE}, doi = {10.1109/68.969880}, pages = {1277 -- 1279}, abstract = {A new method for fabrication of tunable InGaAsP-InP single-mode lasers without epitaxial overgrowth is reported. These devices show the advantage of a considerably simplified fabrication process compared to conventional tunable laser types. The lasers comprise an active Bragg reflector integrated with an uncorrugated separately pumped gain region. By adjusting the current through the Bragg reflector, the wavelength can be tuned between 1590.8 and 1595.2 nm.}, language = {en} } @inproceedings{BuchnerKaiserHausladenetal., author = {Buchner, Philipp and Kaiser, Alexander and Hausladen, Matthias and Bartl, Mathias and Bachmann, Michael and Schreiner, Rupert}, title = {Silicon Nanowire Field Emitters with Integrated Extraction Gates Using Benzocyclobutene as an Insulator}, series = {37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic}, booktitle = {37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic}, publisher = {IEEE}, doi = {10.1109/IVNC63480.2024.10652314}, pages = {1 -- 2}, abstract = {We are continuously improving the performance of our field emission electron sources. In this work a geometrically optimized design of electron sources with silicon nanowire field emitters on pillars was fabricated. This new design increased the packing density of the emitters by using a hexagonal arrangement of the pillars and a pillar spacing of 40 µm. Benzocyclobutene was used as the insulator material for an integrated (Cr/Ni) extraction gate. A modified fabrication process for the field emitters further improved reproducibility and reliability. An emission current of about 0.4 mA was measured for 30 minutes at an extraction voltage of 250 V and an anode voltage of 500 V. Electron transmission through the gate reached almost 100\%.}, language = {en} } @article{BerndtMuggliHeckeletal., author = {Berndt, Dominik and Muggli, Josef and Heckel, Robert and Rahiman, Mohd Fuad and Lindner, Matthias and Heinrich, Stephan and Pl{\"o}chinger, Heinz and Schreiner, Rupert}, title = {A Robust Miniaturized Gas Sensor for H₂ and CO₂ Detection Based on the 3ω Method}, series = {Sensors}, volume = {22}, journal = {Sensors}, number = {2}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/s22020485}, pages = {1 -- 17}, abstract = {Gas concentration monitoring is essential in industrial or life science areas in order to address safety-relevant or process-related questions. Many of the sensors used in this context are based on the principle of thermal conductivity. The 3ω-method is a very accurate method to determine the thermal properties of materials. It has its origin in the thermal characterization of thin solid films. To date, there have been very few scientific investigations using this method to determine the thermal properties of gases and to apply it to gas measurement technology. In this article, we use two exemplary gases (H2 and CO2) for a systematical investigation of this method in the context of gas analysis. To perform our experiments, we use a robust, reliable sensing element that is already well established in vacuum measurement technology. This helix-shaped thin wire of tungsten exhibits high robustness against chemical and mechanical influences. Our setup features a compact measurement environment, where sensor operation and data acquisition are integrated into a single device. The experimental results show a good agreement with a simplified analytical model and FEM simulations. The sensor exhibits a lower detection limit of 0.62\% in the case of CO2, and only 0.062\% in case the of H2 at an excitation frequency of 1 Hz. This is one of the lowest values reported in literature for thermal conductivity H2 sensors.}, language = {en} } @article{SchreinerKoerblGraebeldingeretal., author = {Schreiner, Rupert and K{\"o}rbl, M. and Gr{\"a}beldinger, H. and Gentner, Jean-Louis and Schweizer, H.}, title = {Laterally gain-coupled 1.57 [micro sign]m DFB lasers with chromium surface grating and self-aligned Ti/Pt/Au ohmic contact}, series = {Electronics Letters}, volume = {36}, journal = {Electronics Letters}, number = {7}, publisher = {The Institution of Engineering and Technology, IET}, issn = {0013-5194}, doi = {10.1049/el:20000500}, pages = {636 -- 637}, abstract = {A simple method for fabricating gain coupled DFB lasers with lateral surface chromium Bragg gratings and self-aligned low capacitance ohmic contacts is reported. These InGaAsP/InP lasers show monomode emission with a sidemode suppression ratio of 40 dB. For 243 µm long devices a continuous wave threshold current of 17 mA was measured at room temperature.}, language = {en} } @article{SchreinerLangerPrommesbergeretal., author = {Schreiner, Rupert and Langer, Christoph and Prommesberger, Christian and Dams, Florian}, title = {Compact and Energy-Efficient Field Emission Cathodes for Sensor Applications}, series = {Advanced Materials Research}, volume = {1024}, journal = {Advanced Materials Research}, publisher = {Scientific.net}, doi = {10.4028/www.scientific.net/amr.1024.372}, pages = {372 -- 375}, abstract = {We report on miniaturized silicon field emitter arrays for the application in compact and energy-saving vacuum-microelectronic devices, e.g. sensors or x-ray tubes. Since standard silicon semiconductor technology has been used for the fabrication, they may be easily integrated with other silicon based circuits and devices on the same chip. The silicon tip geometry and the operating conditions were optimized in order to obtain highly uniform and stable electron field emission from large area cathode arrays. A series of uniform hexagonal tip arrays containing each 547 tips were fabricated and characterized. The electron emission properties of both individual tips as well as of complete emitter arrays were investigated. A saturation level in the voltage-current characteristics was found, which can be explained by the limitation of the supply of electrons due to the p-type silicon wafer material. When operating the arrays in the current saturation regime at an emission current of ~ 1 nA per tip, a highly stable and low noise emission can be observed.}, language = {en} } @inproceedings{HausladenBomkeBuchneretal., author = {Hausladen, Matthias and Bomke, Vitali and Buchner, Philipp and Bachmann, Michael and Knapek, Alexandr and Schreiner, Rupert}, title = {Influence of Geometrical Arrangements of Si Tip Arrays Fabricated by Laser Micromachining on their Emission Behaviour}, series = {2021 34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France}, booktitle = {2021 34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France}, publisher = {IEEE}, address = {Piscataway, N.J.}, isbn = {978-1-6654-2589-6}, issn = {2380-6311}, doi = {10.1109/IVNC52431.2021.9600717}, abstract = {ensely packed emitters on a field emission array lead typically to mutual shielding. Taking biology as a role model for geometric arrangements could be a way to reduce this effect. For comparison, two electron sources, one with a spiral and a second with conventional rectangular (orthogonal) arranged emitters, were fabricated and investigated. Emission currents of 6 µA in the spiral ordered array and 120 µA in the rectangular array were reached with an extraction voltage of 400 V. From a mid-term measurement over 1 h a current stability of ±8.8 \% (spiral) respectively ±5.7 \% (rectangular) with a mean degradation of -3.0 µA/h (spiral) and -0.12 µA/h (rectangular) could be observed.}, language = {en} } @inproceedings{BuchnerBomkeHausladenetal., author = {Buchner, Philipp and Bomke, Vitali and Hausladen, Matthias and Edler, Simon and Bachmann, Michael and Schreiner, Rupert}, title = {Investigation on the Emission Behaviour of p-doped Silicon Field Emission Arrays with Individually Controllable Single Tips}, series = {2021 34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France}, booktitle = {2021 34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France}, publisher = {IEEE}, isbn = {978-1-6654-2589-6}, doi = {10.1109/IVNC52431.2021.9600756}, pages = {1 -- 2}, abstract = {Four individually controllable emission tips consisting of <111> p-Type silicon, were structured on a glass substrate by laser ablation. A matching extraction grid was manufactured in the same manner and aligned with the emitters. The resulting samples were characterized in ultra-high vacuum. As expected, the individual currents show a strong saturation and in the saturation region a considerably lower current fluctuation than n-type silicon due to charge carrier depletion. The individual tips behave completely independent behaviour from each other and the overall emission can be deduced from the sum of the currents through the individual tips.}, language = {en} } @inproceedings{HechtBauereiβSellmairetal., author = {Hecht, Fabian and Bauereiβ, Florian and Sellmair, Josef and Buchner, Philipp and Hausladen, Matthias and Schreiner, Rupert}, title = {Electron Beam Induced Growth of Carbon Nanotips on Tungsten and Silicon Fieldemitters}, series = {2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA}, booktitle = {2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA}, publisher = {IEEE}, isbn = {979-8-3503-0143-4}, doi = {10.1109/IVNC57695.2023.10188960}, pages = {160 -- 162}, abstract = {In our experiments we grew electron emitting carbon nanostructures on tungsten tips. Subsequently, we transferred the growth process to pre-structured phosphorus-doped n-type silicon and obtained emitting carbon nanostructures directly grown on silicon. After growth of the nanostructures, the silicon field emitters showed increased emission currents of 76 nA at 1.1 kV (compared to 6 nA under the same conditions before growth).}, language = {en} } @inproceedings{AllahamBuchnerSchreineretal., author = {Allaham, Mohammad M. and Buchner, Philipp and Schreiner, Rupert and Kn{\´a}pek, Alexandr}, title = {Testing the performance of Murphy-Good plots when applied to current-voltage characteristics of Si field electron emission tips}, series = {2021 34th International Vacuum Nanoelectronics Conference (IVNC): 5-9 July 2021, Lyon, France}, booktitle = {2021 34th International Vacuum Nanoelectronics Conference (IVNC): 5-9 July 2021, Lyon, France}, publisher = {IEEE}, doi = {10.1109/IVNC52431.2021.9600690}, pages = {1 -- 2}, abstract = {Murphy-Good plots are the most recent type of the analysis methods in the field electron emission theory, this type of plots has several useful characteristics such as: having the very-nearly straight line to represent the current-voltage characteristics and the absence of the correction factors in the mathematical procedure of the analysis process. In this study, n-type <111> and <100> Si chips containing four individual emitters are used as base emitters and mounted in a diode configuration field emission setup where the experiments are operated in an ultra-high vacuum ( 10-7 Pa). Each chip has four individual controllable emitters with 5 µm distance between the Si tips and the same material grid. Laser micromachining and subsequent wet chemical etching technique is used to structure and polish the tips. Murphy-Good plots are used to study the behavior of the Si individual tips and compare the results with the array current by extracting the field emission characterization parameters of the emitters.}, language = {en} } @inproceedings{ZhengFuhrmannXuetal., author = {Zheng, Jihong and Fuhrmann, Thomas and Xu, Boqing and Schreiner, Rupert and Jia, Hongzhi and Zhang, Wei and Wang, Ning and Seebauer, Gudrun and Zhu, Jiyan}, title = {Curriculum design and German student exchange for Sino-German Bachelor program majored in optoelectronics engineering}, series = {14th Conference on Education and Training in Optics and Photonics (ETOP 2017), 29-31.05.2017, Hangzhou, China, 29-31.05.2017}, booktitle = {14th Conference on Education and Training in Optics and Photonics (ETOP 2017), 29-31.05.2017, Hangzhou, China, 29-31.05.2017}, publisher = {SPIE}, doi = {10.1117/12.2269574}, pages = {134}, abstract = {Different higher education backgrounds in China and Germany led to challenges in the curriculum design at the beginning of our cooperative bachelor program in Optoelectronics Engineering. We see challenges in different subject requirements from both sides and in the German language requirements for Chinese students. The curriculum was optimized according to the AS IIN criteria, which makes it acceptable and und erstandable by both countries. German students are integrated into the Chinese class and get the sa me lectures like their Chinese colleagues. Intercultural and curriculum challenges are successfully solved. The results are summarized to provide an example for other similar international programs.}, language = {en} } @inproceedings{BiekerRoustaieLangeretal., author = {Bieker, Johannes and Roustaie, Farough and Langer, Christoph and Schreiner, Rupert and Schlaak, Helmut F.}, title = {Innovatives Verfahren zur Herstellung und Integration metallischer Nanokonen f{\"u}r die Feldemission}, series = {MikroSystemTechnik Kongress 2017 : MEMS, Mikroelektronik, Systeme 23.-25. Oktober 2017 in M{\"u}nchen}, booktitle = {MikroSystemTechnik Kongress 2017 : MEMS, Mikroelektronik, Systeme 23.-25. Oktober 2017 in M{\"u}nchen}, number = {CD-ROM}, publisher = {VDE-Verlag}, address = {M{\"u}nchen}, isbn = {978-3-8007-4491-6}, pages = {797 -- 800}, abstract = {In den letzten Jahren wurde am Institut f{\"u}r Elektromechanische Konstruktionen die Fabrikation und Integration von metallischen Nanodr{\"a}hten und Nanokonen mittels Template-basierter Abscheidung erforscht. Diese Variante der in-situ Abscheidung von metallischen Nanostrukturen bietet eine Vielzahl von Anwendungsm{\"o}glichkeiten. Im Rahmen dieses Beitrags werden das Herstellungsverfahren zur Herstellung metallischer Nanokonen vorgestellt. Dies beinhaltet sowohl die Templatepr{\"a}paration mittels asymmetrischen {\"A}tzens als auch die anschließende Integration mittels galvanischer Abscheidung. Eine Anwendung der metallischen Nanokonen stellt die Verwendung als Feldemitter in der Vakuumelektronik dar. Es werden erste Messungen der Langzeitstabilit{\"a}t des Feldemissionsstromes der metallischen Konen pr{\"a}sentiert.}, language = {de} } @inproceedings{RahimanBerndtSchreiner, author = {Rahiman, Mohd Fuad and Berndt, Dominik and Schreiner, Rupert}, title = {Micro-wire Pirani with temperature-stabilized Environment}, series = {3. Symposium Elektronik und Systemintegration ESI 2022: 06. April 2022, Hochschule Landshut}, booktitle = {3. Symposium Elektronik und Systemintegration ESI 2022: 06. April 2022, Hochschule Landshut}, isbn = {978-3-9818439-7-2}, pages = {52 -- 59}, language = {en} } @misc{Schreiner, author = {Schreiner, Rupert}, title = {Miniaturized sensor and actuator elements based on the heat transport in gases or the ionization of gas particles}, series = {16th International Conference on Optical and Electronic Sensors, COE'2020, 29 March - 2 April 2020, Krakow, Poland (online)}, journal = {16th International Conference on Optical and Electronic Sensors, COE'2020, 29 March - 2 April 2020, Krakow, Poland (online)}, language = {en} } @inproceedings{KleshchSerbunOrekhovetal., author = {Kleshch, Victor I. and Serbun, Pavel and Orekhov, Anton and L{\"u}tzenkirchen-Hecht, Dirk and Obraztsov, Alexander N. and Prommesberger, Christian and Langer, Christoph and Schreiner, Rupert and Lutzenkirchen-Hecht, Dirk}, title = {Field emission properties of p-type silicon tips decorated with tungsten nanoparticles}, series = {2017 30th International Vacuum Nanoelectronics Conference (IVNC), 10-14 July 2017, Regensburg, Germany}, booktitle = {2017 30th International Vacuum Nanoelectronics Conference (IVNC), 10-14 July 2017, Regensburg, Germany}, publisher = {IEEE}, doi = {10.1109/IVNC.2017.8051580}, pages = {138 -- 139}, abstract = {An array of conical-shaped p-type silicon tips was fabricated by using reactive ion etching and sharpening oxidation. The apex of each tip was decorated by a tungsten hemispherical nanoparticle. Field emission properties of the tips were measured by a tungsten-needle anode positioned above the tip apex. Tips decorated with tungsten nanoparticles demonstrated a smaller saturation region in current-voltage characteristics compared to the pristine tips. An emission activation process, which consisted in sudden current increase at certain value of applied voltage, was observed for the decorated silicon tips. This behavior was explained by the formation of vertical protrusions extending from the metal particles revealed by scanning electron microscopy after field emission experiments.}, language = {en} } @inproceedings{WickLindnerZimmeretal., author = {Wick, Michael and Lindner, Gerhard and Zimmer, Katja and Schreiner, Rupert and Fuhrmann, Thomas and Seebauer, Gudrun and Xu, Boqing and Zheng, Jihong and Wang, Ning}, title = {German-Chinese cooperative Bachelor in engineering physics/optoelectronics}, series = {14th Conference on Education and Training in Optics and Photonics: ETOP 2017; Hangzhou, China 29.05.2017 - 31.05.2017}, booktitle = {14th Conference on Education and Training in Optics and Photonics: ETOP 2017; Hangzhou, China 29.05.2017 - 31.05.2017}, editor = {Liu, Xu and Zhang, Xi-Cheng}, publisher = {SPIE}, isbn = {9781510613812}, doi = {10.1117/12.2269943}, abstract = {The University of Shanghai for Science and Technology (USST), the Coburg University of Applied Sciences and Arts (CUASA) and the OTH Regensburg, University of Applied Sciences (OTHR) established an English taught international cooperative bachelor program in the area of Engineering Physics/Optoelectronics. Students from China study their first four semesters at USST. They continue their studies in Germany for the last three semesters, including an internship and a bachelor thesis, graduating with a Chinese and a German bachelor degree. Students from Germany study their third and fourth semester at USST to gain international experience. While the first cohort of Chinese students is currently in Germany, the second cohort of German students is in Shanghai. Up to now the feedback regarding this study program is completely positive, thus it is planned to develop it further.}, language = {en} } @inproceedings{KnappLangerPrommesbergeretal., author = {Knapp, Wolfram and Langer, Christoph and Prommesberger, Christian and Lindner, Matthias and Schreiner, Rupert}, title = {Investigations of the transition from field electron emission to stable plasma discharge in a micro electron source at vacuum pressure}, series = {2017 30th International Vacuum Nanoelectronics Conference (IVNC), 10-14 July 2017, Regensburg, Germany}, booktitle = {2017 30th International Vacuum Nanoelectronics Conference (IVNC), 10-14 July 2017, Regensburg, Germany}, publisher = {IEEE}, doi = {10.1109/IVNC.2017.8051594}, pages = {166 -- 167}, abstract = {We report on the transition from field electron emission to plasma discharges. During an experiment with a miniaturized field emission electron source a plasma discharge accompanied by a luminous effect was observed. A novel graphical evaluation method was used to interpret and to compare the observed phenomenon.}, language = {en} } @article{SchreinerSchweizer, author = {Schreiner, Rupert and Schweizer, Heinz C.}, title = {High-frequency operation of 1.57-μm laterally coupled distributed feedback lasers with self-aligned ohmic contacts and nickel surface gratings}, series = {IEEE Journal of Selected Topics in Quantum Electronics}, volume = {9}, journal = {IEEE Journal of Selected Topics in Quantum Electronics}, number = {5}, publisher = {IEEE}, doi = {10.1109/JSTQE.2003.819469}, pages = {1179 -- 1182}, abstract = {Laterally coupled distributed feedback lasers with self-aligned ohmic contacts show the advantage of a considerably simplified fabrication process. These lasers exhibit superior spectral properties with full benefit from the gain coupling mechanism. Side-mode suppression ratios up to 55- and 3-dB bandwidths beyond 15 GHz were obtained for these devices.}, language = {en} } @article{DamsSchreiner, author = {Dams, Florian and Schreiner, Rupert}, title = {Influencing factors on the sensitivity of MEMS-based thermal conductivity vacuum gauges}, series = {Journal of vacuum science \& technology A}, volume = {32}, journal = {Journal of vacuum science \& technology A}, number = {3}, publisher = {AVS}, doi = {10.1116/1.4867486}, abstract = {The measurement range of thermal conductivity vacuum gauges is mainly influenced by the sensitivity of the sensing element to variations in pressure. An enhanced definition of sensitivity shows its theoretical dependence on the geometric measures of the sensor element at the whole pressure range. This value gives the possibility of direct comparison between different types of sensor structures without the influence of the operating conditions. To study the influencing factors, sensor chips with heated surfaces in the order of some tens of mm 2 were realized by microelectromechanical systems-based fabrication techniques. By a silicon-glass hybrid process two cold planes were formed in a distance of 150 mu m above and below the heated element. The thermal conductance of devices with different geometric measures was determined in constant temperature operating mode by usage of embedded measurement equipment. In this configuration the sensor signals were sensitive to pressure in a region from 10(-5) mbar. The sensitivity was extracted by a fit of the theoretical model to the measurement data and showed the predicted dependencies on the geometric measures. (C) 2014 American Vacuum Society.}, language = {en} } @article{DamsNavitskiPrommesbergeretal., author = {Dams, Florian and Navitski, Aliaksandr and Prommesberger, Christian and Serbun, Pavel and Langer, Christoph and M{\"u}ller, G{\"u}nter and Schreiner, Rupert}, title = {Homogeneous Field Emission Cathodes With Precisely Adjustable Geometry Fabricated by Silicon Technology}, series = {IEEE Transactions on Electron Devices}, volume = {59}, journal = {IEEE Transactions on Electron Devices}, number = {10}, publisher = {IEEE}, issn = {0018-9383}, doi = {10.1109/TED.2012.2206598}, pages = {2832 -- 2837}, abstract = {Silicon-based cathodes with precisely aligned field emitter arrays of sharp tips applicable for miniaturized electron sources were successfully fabricated and characterized. This was made possible by an improved fabrication process using wet thermal oxidation, wet etching, and reactive-ion etching steps with adjustable anisotropy. As substrate materials, both p-doped silicon and n-doped silicon were used. The cathode chips contain about 3 × 10 5 Si tips/cm 2 in a triangular array with tip heights of 2.5 μm, tip radii of less than 30 nm, and spacing of 20 μm. Well-aligned field emission (FE) and excellent homogeneity from all tips (i.e., 100\% efficiency) and maximum stable currents of typically 0.1 μA (0.6 μA) for p (n)-type Si were reproducibly achieved. The current-voltage characteristics of the p-Si tips exhibit the expected saturation at around 10 nA with around ten times better current stability, whereas the n-Si tips show the usual Fowler-Nordheim behavior. Additional coating of the Si tips with 5-nm Cr and 10-nm Au layers resulted in improved stability and at least five times higher average FE current limits (about 3 μA) at about 30\% higher operation voltage.}, language = {en} } @article{TanYeapChowetal., author = {Tan, Pi Lin and Yeap, Guan Yeow and Chow, Wen Shyang and Schreiner, Rupert and Cheong, Kuan Yew}, title = {Effect of Thickness of Porphyrin on Electrical Properties of Organic Devices}, series = {Advanced Materials Research (AMR)}, volume = {1024}, journal = {Advanced Materials Research (AMR)}, publisher = {Trans Tech Publications Ltd.}, address = {Baech}, issn = {1662-8985}, doi = {10.4028/www.scientific.net/AMR.1024.381}, pages = {381 -- 384}, abstract = {The study on electrical properties for both 2,3,7,8,12,13,17,18-octaethyl-21,23H-porphine Cu (II) (Cu-porphyrin) and 2,3,7,8,12,13,17,18-octaethyl-21,23H-porphine (porphyrin) thin film, which were fabricated using spin coating method was conducted. Porphyrins were diluted with chloroform of various concentrations (0.05 mg/ml, 0.1 mg/ml, 0.5 mg/ml, 2.0 mg/ml and 3.0 mg/ml). The solution was spin coated on top of glass substrates. A layer of aluminum was evaporated on top of the organic thin film through thermal evaporation and shadow mask was placed on top of the organic thin film where two electrodes with a gap of 50 μm were formed. Surface morphology of the organic thin film was observed by scanning electron microscope (SEM) and profilometer. Different concentrations of organic solutions greatly affected the molecular packing and arrangement order of the organic thin film and thickness of the organic layer and eventually affected electrical properties of the devices.}, language = {en} } @article{LangerBerndtSchreiner, author = {Langer, Christoph and Berndt, Dominik and Schreiner, Rupert}, title = {Sensitivity of thermal conductivity vacuum gauges for constant current and constant temperature operation}, series = {Journal of Vacuum Science and Technology B: Nanotechnology and Microelectronics}, volume = {40}, journal = {Journal of Vacuum Science and Technology B: Nanotechnology and Microelectronics}, number = {5}, publisher = {AIP Publishing}, doi = {10.1116/6.0001964}, abstract = {To optimize the measurement range of thermal conductivity vacuum gauges, an expression for the sensitivity is required that takes into account all geometrical, material-specific, and operating parameters. Therefore, equations of the sensor output signal as a function of the pressure for the constant current and the constant temperature mode have been developed analytically. Based on these equations, the sensitivity of the vacuum gauge and its influencing parameters was investigated and discussed. For comparable conditions, the constant temperature operation shows a significantly higher sensitivity for high pressures, while the constant current operation shows higher sensitivity at low pressures. The sensitivity in both the constant current and the constant temperature mode depends on the ratio of the filament surface area and the parasitic thermal conductance. In addition, for the constant current operation, the sensitivity also depends on the current value and the temperature coefficient of the filament resistor. For the constant temperature operation, the sensitivity additionally depends on the distance of the filament and the reference plane. However, to extend the measurement range of a thermal conductivity vacuum gauge toward low pressures, a reduction of the parasitic thermal conductance is mandatory for both the constant current and the constant temperature mode.}, language = {en} } @inproceedings{DamsPrommesbergerSchreiner, author = {Dams, Florian and Prommesberger, Christian and Schreiner, Rupert}, title = {Fabrication process of silicon-tip-arrays for field emission applications}, series = {24th International Vacuum Nanoelectronics Conference (IVNC), 2011 : 18 - 22 July 2011, Historische Stadthalle Wuppertal, Germany}, booktitle = {24th International Vacuum Nanoelectronics Conference (IVNC), 2011 : 18 - 22 July 2011, Historische Stadthalle Wuppertal, Germany}, publisher = {IEEE}, isbn = {978-3-00-035081-8}, issn = {2380-6311}, pages = {49 -- 50}, abstract = {A micromachined process to assemble homogeneous and reproducible tip arrays for field emission applications is developed and characterized. As substrate material p- as well as n-doped silicon is used. Lateral position of the tips is defined by structuring silicon dioxide to discs in a photolithographic process. Vertical structure of the tips is defined by a combination of RIE dry etching with controlled anisotropy and thermally oxidization of silicon in order to sharpen the tips. Hence field emitter arrays (FEAs) can be assembled both as bare and coated cathodes. To assemble field emission diodes, this fabrication process allows placing a metal anode in a micrometer order distance to the tips by a self-aligning procedure. The anode is placed in an evaporation process whereupon sharpening oxide is used as isolator between anode and cathode. Electrical characterization of the cathodes showed very good homogeneity, well alignment and stability over time of emission current from all tips (i.e. 100\% efficiency).}, language = {en} } @inproceedings{SchreinerMulotWiedmannetal., author = {Schreiner, Rupert and Mulot, M. and Wiedmann, J{\"o}rg and Coenning, W. and Porsche, J. and Gentner, Jean-Louis and Berroth, Manfred and Scholz, Ferdinand and Schwizer, H.}, title = {Dynamic measurements on narrow linewidth complex coupled 1.55 μm DFB lasers with gain and index grating in antiphase}, series = {Conference Proceedings. Eleventh International Conference on Indium Phosphide and Related Materials (IPRM'99), 16-20 May 1999, Davos, Switzerland}, booktitle = {Conference Proceedings. Eleventh International Conference on Indium Phosphide and Related Materials (IPRM'99), 16-20 May 1999, Davos, Switzerland}, publisher = {IEEE}, address = {Piscataway}, isbn = {0-7803-5562-8}, doi = {10.1109/ICIPRM.1999.773626}, pages = {25 -- 28}, abstract = {We report on dynamic measurements on antiphase complex coupled 1.55 /spl mu/m DFB lasers. The antiphase complex coupling mechanism is realized by periodically etching the active layer and quarternary InGaAsP overgrowth. This new fabrication approach results in very narrow linewidths measured on devices with rather short resonator lengths. The minimum linewidth for a 375 /spl mu/m long ridge waveguide laser was only 250 kHz at an optical output power of 4 mW. The RC-limited 3dB-bandwidth for those devices was /spl sim/6 GHz. Using circuit model corrections, the intrinsic bandwidth limitation of those lasers was found to be 17.4 GHz.}, language = {en} } @inproceedings{SchreinerNaegeleKoerbletal., author = {Schreiner, Rupert and Naegele, Peter and Koerbl, Michael and Groening, Albert and Gentner, Jean-Louis and Schweizer, Heinz C.}, title = {Monolithically integrated tunable laterally-coupled distributed feedback lasers with self-aligned Ti/Pt/Au ohmic contacts}, series = {Proceedings Volume 4871, Semiconductor Lasers and Optical Amplifiers for Lightwave Communication SystemsSemiconductor Lasers and Optical Amplifiers for Lightwave Communication Systems}, booktitle = {Proceedings Volume 4871, Semiconductor Lasers and Optical Amplifiers for Lightwave Communication SystemsSemiconductor Lasers and Optical Amplifiers for Lightwave Communication Systems}, editor = {Mirin, Richard P. and Menoni, Carmen S.}, publisher = {SPIE}, doi = {10.1117/12.457281}, pages = {160}, abstract = {We present a new method for fabrication of tunable InGaAsP-InP single mode lasers without epitaxial overgrowth. These devices show the advantage of a considerably simplified fabrication process compared to conventional tunable laser types. The lasers comprise an active Bragg reflector integrated with an uncorrugated separately pumped gain region. To overcome the extensive and expensive overgrowth step we realized a surface grating on both sides of the ridge mesa, which provides DFB operation. By adjusting the current through the Bragg reflector, the wavelength can be tuned between 1590.8 nm and 1595.2 nm. A maximum of 11 wavelength channels with an average spacing of ~0.5 nm and a constant optical output power of ~0.5 mW are addressable.}, language = {en} } @article{CheongAwKarimovetal., author = {Cheong, Kuan Yew and Aw, Kean and Karimov, Khasan S. and Zhao, Feng and Mahroof-Tahir, Mohammad and Schreiner, Rupert}, title = {Advances in Smart Materials and Applications}, series = {Advances in Materials Science and Engineering}, journal = {Advances in Materials Science and Engineering}, publisher = {Hindawi}, doi = {10.1155/2014/517342}, abstract = {This is one of a series of special issues published in Advances in Materials Science and Engineering, focusing on the latest advances of smart materials and their applications. Evolution of engineering materials is strongly depending on the growing transformation of complexity in engineering products. New materials being designed are required to provide specific properties and demonstrate certain functional characteristics by manipulating their dimension, chemistry, and structure through various advanced technologies. Therefore, "smartness" of a material has become the topic of interest. Properties of smart materials may change accordingly to the applied external stimuli. Under the direction of the editorial team, we showcase advances of organic and inorganic based smart materials and their applications in areas of specific interest such as energy, environment, and health. A total of 9 articles are published in this special issue. Six articles are focused on production, synthesis, and optimization of smart materials; and the remaining are dedicated to application of smart materials.}, language = {en} } @inproceedings{SaravananGerlachPeschkeetal., author = {Saravanan, Brem Kumar and Gerlach, Philipp and Peschke, Martin and Knoedl, Thomas and Schreiner, Rupert and Hanke, Christian and Stegmueller, Bernhard}, title = {Integrated DFB laser electro-absorption modulator based on identical MQW-double stack active layer for high-speed modulation beyond 10 GBIT/S}, series = {16th IPRM. 2004 International Conference on Indium Phosphide and Related Materials, 31 May - 04 June 2004, Kagoshima, Japan}, booktitle = {16th IPRM. 2004 International Conference on Indium Phosphide and Related Materials, 31 May - 04 June 2004, Kagoshima, Japan}, publisher = {IEEE}, isbn = {0-7803-8595-0}, doi = {10.1109/ICIPRM.2004.1442656}, pages = {236 -- 238}, abstract = {Integrated DFBLD-EAM-SOA devices utilizing an identical MQW active region have been realized in the AlGaInAs/InP material system. A fiber-coupled optical power of >6 mW with a 10 dB static extinction, 44 dB SMSR single-mode spectrum and a 3 dBe cutoff frequency of 25 GHz was measured.}, language = {en} } @article{ZahnerSchreinerStierstorferetal., author = {Zahner, Th and Schreiner, Rupert and Stierstorfer, R. and Kus, O. and Li, S. T. and Roessler, R. and Pedarnig, J. D. and B{\"a}uerle, D. and Lengfellner, H.}, title = {Off-diagonal Seebeck effect and anisotropic thermopower in Bi2Sr2CaCu2O8 thin films}, series = {Europhysics Letters}, volume = {40}, journal = {Europhysics Letters}, number = {6}, publisher = {IOP Sciences}, doi = {10.1209/epl/i1997-00521-4}, pages = {673 -- 678}, abstract = {The anisotropy ΔS of the thermopower in thin films of the high-Tc superconductor Bi2Sr2CaCu2O8 is investigated using off-c-axis epitaxial film growth and the off-diagonal Seebeck effect. The measurements represent a new method for the investigation of anisotropic transport properties in solids, taking advantage of the availability of oriented grown crystalline thin films instead of using bulk crystals. First results for the temperature dependence ΔS(T) in Bi2Sr2CaCu2O8 thin films are presented and described within a two-band model. Subjecting the films to heat treatments in different gases at relatively low temperatures, ΔS could reversibly be changed in a wide range.}, language = {en} } @inproceedings{KnodlHankeSaravananetal., author = {Knodl, Thomas and Hanke, Christian and Saravanan, Brem Kumar and Peschke, Martin and Schreiner, Rupert and Stegmuller, Bernhard}, title = {Integrated 1.3-μm InGaAlAs-InP laser-modulator with double-stack MQW layer structure}, series = {Proceedings Volume 5451, Integrated Optics and Photonic Integrated Circuits}, booktitle = {Proceedings Volume 5451, Integrated Optics and Photonic Integrated Circuits}, editor = {Righini, Giancarlo C. and Honkanen, Seppo}, publisher = {SPIE}, doi = {10.1117/12.544610}, pages = {1}, abstract = {We present first experimental results of the successful transfer of our monolithic integrated double-stack multi quantum well laser-modulator approach from the traditional InGaAsP/InP to the more promising InGaAlAs/InP material system. In continuous wave operation at room temperature, the devices achieved threshold currents of <21 mA, fiber coupled optical power levels up to 570 μW and static extinction ratios in the range of 15 dB/V. The measured small-signal modulation bandwidth of about 10 GHz is capacitance limited due to a conservative device layout.}, language = {en} } @inproceedings{SchreinerGrabeldingerWiedmannetal., author = {Schreiner, Rupert and Grabeldinger, H. and Wiedmann, J. and Wunstel, K. and Porsche, J. and Scholz, Ferdinand and Schweizer, H.}, title = {Complex coupled 1.55 mu m tunable super-grating DFB lasers and photonic filters}, series = {Compound semiconductors 1999 : proceedings of the Twenty-Sixth International Symposium on Compound Semiconductors held in Berlin, Germany, 22 - 26 August 1999}, booktitle = {Compound semiconductors 1999 : proceedings of the Twenty-Sixth International Symposium on Compound Semiconductors held in Berlin, Germany, 22 - 26 August 1999}, publisher = {Inst. of Physics Publ.}, address = {Bristol [u.a.]}, isbn = {0-7503-0704-8}, abstract = {We report on the investigation and realization of photonic filters based on the combination of fractional compositions of a few basic grating periods. Using a minimum set of two basic periods Lambda(1) and Lambda(2) we demonstrate comb-like few mode photonic band gap structures with arbitrary numbers of bands and frequency spacing between the bands. Optically integrated filters of different comb periods result in switchable wavelength filters for channel selection in WDM applications.}, language = {en} } @inproceedings{SchreinerSchweizer, author = {Schreiner, Rupert and Schweizer, Heinz C.}, title = {High frequency operation of 1.57 μm laterally gain coupled DFB lasers with self aligned ohmic contacts and nickel surface gratings}, series = {IEEE 18th International Semiconductor Laser Conference; 29 Sept.-3 Oct. 2002, Garmisch, Germany}, booktitle = {IEEE 18th International Semiconductor Laser Conference; 29 Sept.-3 Oct. 2002, Garmisch, Germany}, publisher = {IEEE}, isbn = {0-7803-7598-X}, doi = {10.1109/ISLC.2002.1041099}, pages = {21 -- 22}, abstract = {Laterally coupled DFB lasers with self-aligned ohmic contacts show the advantage of a, considerably simplified fabrication process. Side-mode-suppresion-ratios up to 55 dB and 3 dB-bandwidths beyond 15 GHz were obtained for these devices.}, language = {en} } @inproceedings{PodstranskyHausladenZlamaletal., author = {Podstr{\´a}nsk{\´y}, J{\´a}chym and Hausladen, Matthias and Zl{\´a}mal, Jakub and Kn{\´a}pek, Alexandr and Schreiner, Rupert}, title = {Single Column Multiple Electron Beam Imaging from N-Type Silicon}, series = {37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic}, booktitle = {37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic}, publisher = {IEEE}, isbn = {979-8-3503-7976-1}, doi = {10.1109/IVNC63480.2024.10652470}, pages = {1 -- 2}, abstract = {This work is aimed at measuring the electron emission from multiple cathodes formed by n-doped silicon and imaging the electron beams focused by an einzel lens on a CMOS camera. The experimental results are compared with computer simulation to understand the electron emission from the semiconductor cathode and the observed imaging imperfections. Finally, modifications to the experimental setup are suggested that should lead to improvement in the extraction current and spot size of focused electron beams and also better understanding of the processes taking place in the experiment.}, language = {en} } @article{SchmidtDenkerDashielletal., author = {Schmidt, Oliver G. and Denker, Ullrich and Dashiell, Michael W. and Jin-Phillipp, Neng Yun and Eberl, Karl and Schreiner, Rupert and Gr{\"a}beldinger, Hedwig and Schweizer, Heinz C. and Christiansen, Silke H. and Ernst, Frank}, title = {Laterally aligned Ge/Si islands: a new concept for faster field-effect transistors}, series = {Materials Science and Engineering B}, volume = {89}, journal = {Materials Science and Engineering B}, number = {1-3}, publisher = {Elsevier}, address = {New York, NY}, issn = {1873-4944}, doi = {10.1016/S0921-5107(01)00810-8}, pages = {101 -- 105}, abstract = {Self-assembled and coherently strained Ge dots were grown on a Si/SiGe superlattice, which was deposited on a flat Si(001) substrate surface patterned with a regular array of straight trenches. The superlattice translates the surface modulation of the substrate into a strain-field modulation, which causes the Ge dots on its surface to form along straight lines above the buried trenches. This approach provides self-assembled Ge dots with excellent lateral periodicity, which might be useful for fabricating dot-based field-effect-transistors (DotFETs). Here, we propose the concept of a modulation-doped p-channel DotFET (p-MOD-DotFET). The p-MOD-DotFET relies on embedded Ge-rich nanostructures, which provide p-channels through the Ge-rich dots. A high Ge concentration in the dots is desirable in order to exploit the high hole mobility of Ge-rich material. We show that the commonly observed Si-Ge intermixing during Si capping of Ge dots can be suppressed by overgrowing the islands at low temperature.}, language = {en} } @inproceedings{EilerHoeglLindneretal., author = {Eiler, Julian and H{\"o}gl, Christina and Lindner, Matthias and Bachmann, Michael and Schreiner, Rupert}, title = {Miniaturized Surface Dielectric Barrier Discharge Plasma Actuators for Application in Chemical Analysis Systems}, series = {2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA}, booktitle = {2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA}, publisher = {IEEE}, isbn = {979-8-3503-0143-4}, doi = {10.1109/IVNC57695.2023.10188884}, pages = {40 -- 42}, abstract = {A new concept for a miniaturized planar ion source based on a surface dielectric barrier discharge (SDBD) is presented. A fabrication method based on a stamping process is described, and the plasma actuators are characterized based on their power in dependence of the applied voltage. The voltage for plasma ignition is approx. 1 kV with a maximum plasma power of 40 W/m at 3,4 kV.}, language = {en} } @inproceedings{BartlBuchnerHausladenetal., author = {Bartl, Mathias and Buchner, Philipp and Hausladen, Matthias and Asgharzadehkhorasani, Ali and Bachmann, Michael and Schreiner, Rupert}, title = {Simulations and Investigations of Silicon Nanowire Field Emitters}, series = {37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic}, booktitle = {37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic}, publisher = {IEEE}, doi = {10.1109/IVNC63480.2024.10652355}, pages = {1 -- 2}, abstract = {The emission behavior of field emission electron sources consisting of a silicon nanowire cathode, an extraction grid electrode and a planar anode was investigated based on a particle tracing simulation using FEM. The focus was on the influence of the grid geometry as well as the positioning of the grid relative to the emitters on the electron transmission. The highest transmission can be achieved with the emitter tips protruding 10 µm trough the extraction grid openings. The transmission decreases more rapidly with increasing distance between the tip and the grid the thicker the grid is.}, language = {en} } @article{HausladenBuchnerBartletal., author = {Hausladen, Matthias and Buchner, Philipp and Bartl, Mathias and Bachmann, Michael and Schreiner, Rupert}, title = {Integrated multichip field emission electron source fabricated by laser-micromachining and MEMS technology}, series = {Journal of Vacuum Science \& Technology B}, volume = {42}, journal = {Journal of Vacuum Science \& Technology B}, number = {1}, publisher = {AIP Publishing}, doi = {10.1116/6.0003233}, abstract = {In this work, high-current field emission electron source chips were fabricated using laser-micromachining and MEMS technology. The resulting chips were combined with commercially available printed circuit boards (PCBs) to obtain a multichip electron source. By controlling the separate electron sources using an external current control circuit, we were able to divide the desired total current evenly across the individual chips deployed in the PCB-carrier. In consequence, we were able to show a decreased degradation due to the reduced current load per chip. First, a single electron source chip was measured without current regulation. A steady-state emission current of 1 mA with a high stability of ±1.3\% at an extraction voltage of 250 V was observed. At this current level, a mean degradation slope of -0.7 μA/min with a nearly perfect transmission ratio of 99\% ± 0.4\% was determined. The measurements of a fully assembled multichip PCB-carrier electron source, using a current control circuit for regulation, showed that an even distribution of the desired total current led to a decreased degradation. This was determined by the increase in the required extraction voltage over time. For this purpose, two current levels were applied to the electron source chips of the PCB-carrier using an external current control circuit. First, 300 μA total current was evenly distributed among the individual electron source chips followed by the emission of 300 μA per electron source chip. This allows the observation of the influence of a distributed and nondistributed total current, carried by the electron source chips. Thereby, we obtained an increase in the mean degradation slope from +0.011 V/min (300 μA distributed) to +0.239 V/min (300 μA per chip), which is approximately 21 times higher. Moreover, our current control circuit improved the current stability to under 0.1\% for both current levels, 300 μA distributed and 300 μA per chip.}, language = {en} } @article{RemškarJelencCzepurnyietal., author = {Remškar, Maja and Jelenc, Janez and Czepurnyi, Nikolai and Malok, Matjaž and Pirker, Luka and Schreiner, Rupert and H{\"u}ttel, Andreas K.}, title = {Modulations of the work function and morphology of a single MoS2 nanotube by charge injection}, series = {Nanoscale Advances}, journal = {Nanoscale Advances}, publisher = {Royal Society of Chemistry (RSC)}, issn = {2516-0230}, doi = {10.1039/d4na00490f}, abstract = {Both the miniaturization of transistor components and the ongoing investigation of material systems with potential for quantum information processing have significantly increased current interest of researchers in semiconducting inorganic nanotubes. Here we report on an additional outstanding aspect of these nanostructures, namely the intrinsic coupling of electronic and mechanical properties. We observe electronic and morphology changes in a single MoS2 nanotube, exposed to charge injections by means of an atomic-force-microscopy tip. An elliptic deformation of the nanotube and helical twisting of the nanotube are visible, consistent with the reverse piezoelectric effect. Work-function changes are found to be dependent on the polarity of the injected carriers. An unexpected long-term persistence of the shape deformations is observed and explained with accumulation of structural defects and the resultant strain, which could cause a memory-like charge confinement and a long lasting modulation of the work function.}, language = {en} } @article{LindnerPipaKarpenetal., author = {Lindner, Matthias and Pipa, Andrei V. and Karpen, Norbert and Hink, R{\"u}diger and Berndt, Dominik and Foest, R{\"u}diger and Bonaccurso, Elmar and Weichwald, Robert and Friedberger, Alois and Caspari, Ralf and Brandenburg, Ronny and Schreiner, Rupert}, title = {Icing Mitigation by MEMS-Fabricated Surface Dielectric Barrier Discharge}, series = {Applied Sciences}, volume = {11}, journal = {Applied Sciences}, number = {23}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/app112311106}, pages = {1 -- 17}, abstract = {Avoiding ice accumulation on aerodynamic components is of enormous importance to flight safety. Novel approaches utilizing surface dielectric barrier discharges (SDBDs) are expected to be more efficient and effective than conventional solutions for preventing ice accretion on aerodynamic components. In this work, the realization of SDBDs based on thin-film substrates by means of micro-electro-mechanical-systems (MEMS) technology is presented. The anti-icing performance of the MEMS SDBDs is presented and compared to SDBDs manufactured by printed circuit board (PCB) technology. It was observed that the 35 mu m thick electrodes of the PCB SDBDs favor surface icing with an initial accumulation of supercooled water droplets at the electrode impact edges. This effect was not observed for 0.3 mu m thick MEMS-fabricated electrodes indicating a clear advantage for MEMS-technology SDBDs for anti-icing applications. Titanium was identified as the most suitable material for MEMS electrodes. In addition, an optimization of the MEMS-SDBDs with respect to the dielectric materials as well as SDBD design is discussed.}, language = {en} } @misc{ScharfenbergMottokArtmannetal., author = {Scharfenberg, Georg and Mottok, J{\"u}rgen and Artmann, Christina and Hobelsberger, Martin and Paric, Ivan and Großmann, Benjamin and Pohlt, Clemens and Wackerbarth, Alena and Pausch, Uli and Heidrich, Christiane and Fadanelli, Martin and Elsner, Michael and P{\"o}cher, Daniel and Pittroff, Lenz and Beer, Stefan and Br{\"u}ckl, Oliver and Haslbeck, Matthias and Sterner, Michael and Thema, Martin and Muggenthaler, Nicole and Lenck, Thorsten and G{\"o}tz, Philipp and Eckert, Fabian and Deubzer, Michael and Stingl, Armin and Simsek, Erol and Kr{\"a}mer, Stefan and Großmann, Benjamin and Schlegl, Thomas and Niedersteiner, Sascha and Berlehner, Thomas and Joblin, Mitchell and Mauerer, Wolfgang and Apel, Sven and Siegmund, Janet and Riehle, Dirk and Weber, Joachim and Palm, Christoph and Zobel, Martin and Al-Falouji, Ghassan and Prestel, Dietmar and Scharfenberg, Georg and Mandl, Roland and Deinzer, Arnulf and Halang, W. and Margraf-Stiksrud, Jutta and Sick, Bernhard and Deinzer, Renate and Scherzinger, Stefanie and Klettke, Meike and St{\"o}rl, Uta and Wiech, Katharina and Kubata, Christoph and Sindersberger, Dirk and Monkman, Gareth J. and Dollinger, Markus and Dembianny, Sven and K{\"o}lbl, Andreas and Welker, Franz and Meier, Matthias and Thumann, Philipp and Swidergal, Krzysztof and Wagner, Marcus and Haug, Sonja and Vernim, Matthias and Seidenst{\"u}cker, Barbara and Weber, Karsten and Arsan, Christian and Schone, Reinhold and M{\"u}nder, Johannes and Schroll-Decker, Irmgard and Dillinger, Andrea Elisabeth and Fuchshofer, Rudolf and Monkman, Gareth J. and Shamonin (Chamonine), Mikhail and Geith, Markus A. and Koch, Fabian and {\"U}hlin, Christian and Schratzenstaller, Thomas and Saßmannshausen, Sean Patrick and Auchter, Eberhard and Kriz, Willy and Springer, Othmar and Thumann, Maria and Kusterle, Wolfgang and Obermeier, Andreas and Udalzow, Anton and Schmailzl, Anton and Hierl, Stefan and Langer, Christoph and Schreiner, Rupert}, title = {Forschungsbericht 2015}, editor = {Baier, Wolfgang}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg}, isbn = {978-3-00-048589-3}, doi = {10.35096/othr/pub-1386}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-13867}, language = {de} } @inproceedings{KrysztofUrbańskiGrzebyketal., author = {Krysztof, Michał and Urbański, Paweł and Grzebyk, Tomasz and Hausladen, Matthias and Schreiner, Rupert}, title = {MEMS X-Ray Source: Electron Emitter Development}, series = {2022 21st International Conference on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS): 12-15 Dec. 2022, Salt Lake City, UT, USA}, booktitle = {2022 21st International Conference on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS): 12-15 Dec. 2022, Salt Lake City, UT, USA}, publisher = {IEEE}, doi = {10.1109/PowerMEMS56853.2022.10007563}, pages = {248 -- 251}, abstract = {The article presents a fabrication process and characterization of silicon emitters designed for MEMS X-ray source. The emitters, made of p-type and n-type silicon, were prepared by a modified laser micromachining process. Both types of emitters worked without any carbon nanotube coverage, which was the case in the previous realization of electron emitters. The p-type emitter gave smaller electron beam currents (<50 nA) with stable emission in a saturation region. The n-type emitter provides higher emission currents (>1 µA) not limited by saturation region, but with higher fluctuations. The final choice of emitter will be adjusted for different applications.}, language = {en} } @misc{BeimlerLeisslEbneretal., author = {Beimler, Josef and Leißl, Caroline and Ebner, Lena and Elsner, Michael and M{\"u}hlbauer, Gerhard and Kohlert, Dieter and Schubert, Martin J. W. and Weiß, Andreas P. and Sterner, Michael and Raith, Thomas and Afranseder, Martin and Krapf, Tobias and Mottok, J{\"u}rgen and Siemers, Christian and Großmann, Benjamin and H{\"o}cherl, Johannes and Schlegl, Thomas and Schneider, Ralph and Milaev, Johannes and Rampelt, Christina and Roduner, Christian and Glowa, Christoph and Bachl, Christoph and Schliekmann, Claus and Gnan, Alfons and Grill, Martin and Ruhland, Karl and Piehler, Thomas and Friers, Daniel and Wels, Harald and Pflug, Kenny and Kucera, Markus and Waas, Thomas and Schlachetzki, Felix and Boy, Sandra and Pemmerl, Josef and Leis, Alexander and Welsch, Andreas F.X. and Graf, Franz and Zenger, Gerhard and Volbert, Klaus and Waas, Thomas and Scherzinger, Stefanie and Klettke, Meike and St{\"o}rl, Uta and Heyl, C. and Boldenko, A. and Monkman, Gareth J. and Kujat, Richard and Briem, Ulrich and Hierl, Stefan and Talbot, Sebastian and Schmailzl, Anton and Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert and Valentino, Piergiorgio and Romano, Marco and Ehrlich, Ingo and Furgiuele, Franco and Gebbeken, Norbert and Eisenried, Michael and Jungbauer, Bastian and Hutterer, Albert and Bauhuber, Michael and Mikrievskij, Andreas and Argauer, Monika and Hummel, Helmut and Lechner, Alfred and Liebetruth, Thomas and Schumm, Michael and Joseph, Saskia and Reschke, Michael and Soska, Alexander and Schroll-Decker, Irmgard and Putzer, Michael and Rasmussen, John and Dendorfer, Sebastian and Weber, Tim and Al-Munajjed, Amir Andreas and Verkerke, Gijsbertus Jacob and Renkawitz, Tobias and Haug, Sonja and Rudolph, Clarissa and Zeitler, Annika and Schaubeck, Simon and Steffens, Oliver and Rechenauer, Christian and Schulz-Brize, Thekla and Fleischmann, Florian and Kusterle, Wolfgang and Beer, Anne and Wagner, Bernd and Neidhart, Thomas}, title = {Forschungsbericht 2013}, editor = {Baier, Wolfgang}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg}, doi = {10.35096/othr/pub-799}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-7990}, pages = {80}, language = {de} } @misc{MauererRexhepajMonkmanetal., author = {Mauerer, Wolfgang and Rexhepaj, Tanja and Monkman, Gareth J. and Sindersberger, Dirk and Diermeier, Andreas and Neidhart, Thomas and Wolfrum, Dominik and Sterner, Michael and Heberl, Michael and Nusko, Robert and Maier, Georg and Nagl, Klaus and Reuter, Monika and Hofrichter, Andreas and Lex, Thomas and Lesch, Florian and Kieninger, B{\"a}rbel and Szalo, Alexander Eduard and Zehner, Alexander and Palm, Christoph and Joblin, Mitchell and Apel, Sven and Ramsauer, Ralf and Lohmann, Daniel and Westner, Markus and Strasser, Artur and Munndi, Maximilian and Ebner, Lena and Elsner, Michael and Weiß, Nils and Segerer, Matthias and Hackenberg, Rudolf and Steger, Sebastian and Schmailzl, Anton and Dostalek, Michael and Armbruster, Dominik and Koch, Fabian and Hierl, Stefan and Thumann, Philipp and Swidergal, Krzysztof and Wagner, Marcus and Briem, Ulrich and Diermeier, Andreas and Spreitzer, Stefan and Beiderbeck, Sabrina and Hook, Christian and Zobel, Martin and Weber, Tim and Groß, Simon and Penzkofer, Rainer and Dendorfer, Sebastian and Schillitz, Ingo and Bauer, Thomas and Rudolph, Clarissa and Schmidt, Katja and Liebetruth, Thomas and Hamer, Markus and Haug, Sonja and Vernim, Matthias and Weber, Karsten and Saßmannshausen, Sean Patrick and Books, Sebastian and Neuleitner, Nikolaus and Rechenauer, Christian and Steffens, Oliver and Kusterle, Wolfgang and G{\"o}mmel, Roland and Wellnitz, Felix and Stierstorfer, Johannes and Stadler, Dominik and Hofmann, Matthias J. and Motschmann, Hubert and Shamonin (Chamonine), Mikhail and Bleicher, Veronika and Fischer, Sebastian and Hackenberg, Rudolf and Horn, Anton and Kawasch, Raphael and Petzenhauser, Michael and Probst, Tobias and Udalzow, Anton and Dams, Florian and Schreiner, Rupert and Langer, Christoph and Prommesberger, Christian and Ławrowski, Robert Damian}, title = {Forschungsbericht 2016}, editor = {Baier, Wolfgang}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg}, doi = {10.35096/othr/pub-1384}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-13840}, language = {de} } @misc{LautenschlaegerLeisDendorferetal., author = {Lautenschl{\"a}ger, Toni and Leis, Alexander and Dendorfer, Sebastian and Palm, Christoph and Schreiner, Rupert and Langer, Christoph and Prommesberger, Christian and Ławrowski, Robert Damian and Dams, Florian and Bornmann, Benjamin and Navitski, Aliaksandr and Serbun, Pavel and M{\"u}ller, G{\"u}nter and Liebetruth, Thomas and Kohlert, Dieter and Pernsteiner, Jochen and Schreier, Franz and Heerklotz, Sabrina and Heerklotz, Allwin and Boos, Alexander and Herwald, Dominik and Monkman, Gareth J. and Treiber, Daniel and Mayer, Matthias and H{\"o}rner, Eva and Bentz, Alexander and Shamonin (Chamonine), Mikhail and Johansen, S{\o}ren Peter and Reichel, Marco and Stoll, Andrea and Briem, Ulrich and Dullien, Silvia and Renkawitz, Tobias and Weber, Tim and Dendorfer, Sebastian and Grifka, Joachim and Penzkofer, Rainer and Barnsteiner, K. and Jovanovik, M. and Wernecke, P. and V{\"o}gele, A. and Bachmann, T. and Pl{\"o}tz, Martin and Schliekmann, Claus and Wels, Harald and Helmberger, Paul and Kaspar, Marcel and H{\"o}nicka, M. and Schrammel, Siegfried and Enser, Markus and Schmidmeier, Monika and Schroll-Decker, Irmgard and Haug, Sonja and Gelfert, Verena and Vernim, Matthias}, title = {Forschungsbericht 2012}, editor = {Baier, Wolfgang}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg}, doi = {10.35096/othr/pub-783}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-7834}, pages = {64}, language = {de} } @misc{AppelhansKampmannMottoketal., author = {Appelhans, Marie-Luise and Kampmann, Matthias and Mottok, J{\"u}rgen and Riederer, Michael and Nagl, Klaus and Steffens, Oliver and D{\"u}nnweber, Jan and Wildgruber, Markus and Roth, Julius and Stadler, Timo and Palm, Christoph and Weiß, Martin Georg and Rochholz, Sandra and Bierl, Rudolf and Gschossmann, Andreas and Haug, Sonja and Schmidbauer, Simon and Koch, Anna and Westner, Markus and Bary, Benedikt von and Ellermeier, Andreas and V{\"o}gele, Daniel and Maiwald, Frederik and Hierl, Stefan and Schlamp, Matthias and Ehrlich, Ingo and Siegl, Marco and H{\"u}ntelmann, Sven and Wildfeuer, Matthias and Br{\"u}ckl, Oliver and Sterner, Michael and Hofrichter, Andreas and Eckert, Fabian and Bauer, Franz and Dawoud, Belal and Rabl, Hans-Peter and Gamisch, Bernd and Schmidt, Ottfried and Heberl, Michael and Thema, Martin and Mayer, Ulrike and Eller, Johannes and Sippenauer, Thomas and Adelt, Christian and Haslbeck, Matthias and Vogl, Bettina and Mauerer, Wolfgang and Ramsauer, Ralf and Lohmann, Daniel and Sax, Irmengard and Gabor, Thomas and Feld, Sebastian and Linnhoff-Popien, Claudia and Ławrowski, Robert Damian and Langer, Christoph and Schreiner, Rupert and Sellmair, Josef}, title = {Forschung 2019}, editor = {Baier, Wolfgang}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg}, isbn = {978-3-9818209-7-3}, doi = {10.35096/othr/pub-789}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-7890}, pages = {72}, abstract = {Bericht mit Forschungsprojekten aus verschiedenen Bereichen der OTH Regensburg mit dem Schwerpunktthema "K{\"u}nstliche Intelligenz" und einem Gespr{\"a}ch zur "Medizin der Zukunft"}, subject = {Forschung}, language = {de} } @inproceedings{LangerPrommesbergerDamsetal., author = {Langer, Christoph and Prommesberger, Christian and Dams, Florian and Schreiner, Rupert}, title = {Theoretical investigations into the field enhancement factor of silicon structures}, series = {25th International Vacuum Nanoelectronics Conference (IVNC) - Jeju, Korea (South), 09.- 13.07.2012}, booktitle = {25th International Vacuum Nanoelectronics Conference (IVNC) - Jeju, Korea (South), 09.- 13.07.2012}, publisher = {IEEE}, address = {Piscataway, N.J.}, isbn = {978-1-4673-1984-3}, issn = {2380-6311}, doi = {10.1109/IVNC.2012.6316886}, abstract = {In order to optimize our field-emitting silicon structures, the influence of geometric parameters like aspect ratio, aperture angle and curvature on the field enhancement factor was investigated by finite element simulations. A universal geometric model consisting of a rounded triangle and elliptic curvatures was taken for modeling a variety of different silicon tip as well as ridge structures. Whereas, a high dependency of the field enhancement on the aperture angle was found, the simulations show that the elliptic curvature affects the field enhancement only marginal.}, language = {en} } @article{PrommesbergerBachmannDuesbergetal., author = {Prommesberger, Christian and Bachmann, Michael and D{\"u}sberg, Felix and Langer, Christoph and Ławrowski, Robert Damian and Hofmann, Martin and Pahlke, Andreas and Schreiner, Rupert}, title = {Regulation of the Transmitted Electron Flux in a Field-Emission Electron Source Demonstrated on Si Nanowhisker Cathodes}, series = {IEEE Transactions on Electron Devices}, volume = {64}, journal = {IEEE Transactions on Electron Devices}, number = {12}, publisher = {IEEE}, issn = {5128-5133}, doi = {10.1109/TED.2017.2763239}, abstract = {We report on a method to stabilize the transmitted electron flux in a field-emission electron source using an external regulation circuit. The electron source was realized with an array of silicon (Si) nanowhiskers on the top of elongated pillar structures, a mica spacer, and an extraction grid made of Si. As for most applications, the emitted electron current from the cathode is not as crucial as the transmitted electron flux through the extraction grid toward the anode. We investigated a method which allows the regulation directly by the emitted electron flux and not merely on the cathode current. By using this method, we were able to stabilize the emitted electron flux of our electron source down to values below 1\%. Simultaneously, it was shown that there is the possibility to stabilize the influencing value in the real application as well. The effectiveness of this method was demonstrated successfully with an X-ray source setup. The measured X-ray photon count rate was stabilized to a standard deviation of 0.30\% at a pressure of 1 × 10 -7 mbar. Even in harsh environment of 2 × 10 -5 mbar, a stabilization of the X-ray photon count rate down to a value of 0.63\% was achieved.}, language = {en} } @article{LangerBomkeHausladenetal., author = {Langer, Christoph and Bomke, Vitali and Hausladen, Matthias and Ławrowski, Robert Damian and Prommesberger, Christian and Bachmann, Michael and Schreiner, Rupert}, title = {Silicon Chip Field Emission Electron Source Fabricated by Laser Micromachining}, series = {Journal of Vacuum Science \& Technology B}, volume = {38}, journal = {Journal of Vacuum Science \& Technology B}, number = {1}, publisher = {AIP Publishing}, doi = {10.1116/1.5134872}, abstract = {The components for a silicon chip electron source were fabricated by laser micromachining using pulsed laser ablation and wet chemical cleaning and etching dips. The field emission electron source consists of a silicon field emission cathode with 4 × 4 conical shaped emitters with a height of 250 μm and a tip radius of about 50 nm, a 50 μm thick laser-structured mica spacer, and a silicon grid electrode with a grid periodicity of 200 μm and a bar width of 50 μm. These three components are combined to a single chip with the size of 14 × 10 mm2 and the thickness of 1 mm to form the electron source. Several of these devices were characterized in ultrahigh vacuum. Onset voltages of about 165 V and cathode currents of about 15 μA for voltages lower than 350 V were observed. Operating the electron source with an anode voltage of 500 V and an extraction grid voltage of 300 V yielded a cathode current of 4.5 μA ± 8.9\%, an anode current of 4.0 μA ± 9.6\%, and a corresponding grid transmittance of 89\%. Regulating the anode current by the extraction grid voltage, an extremely stable anode current of 5.0 μA ± 0.017\% was observed. A long-term measurement over 120 h was performed, and no significant degradation or failure was observed.}, language = {en} } @article{BreuerBachmannDuesbergetal., author = {Breuer, Janis and Bachmann, Michael and D{\"u}sberg, Felix and Pahlke, Andreas and Edler, Simon and Langer, Christoph and Prommesberger, Christian and Ławrowski, Robert Damian and Schreiner, Rupert and Serbun, Pavel and L{\"u}tzenkirchen-Hecht, Dirk}, title = {Extraction of the current distribution out of saturated integral measurement data of p-type silicon field emitter arrays}, series = {Journal of Vacuum Science and Technology B}, volume = {36}, journal = {Journal of Vacuum Science and Technology B}, number = {5}, publisher = {AIP Publishing}, doi = {10.1116/1.5035189}, abstract = {At the moment, only complicated techniques are known for the determination of array properties of field emitter arrays such as the number of active tips, the current distribution, or the individual tip radii. In this work, a method for extracting these parameters from integral measurement data is presented. A model describing the characteristics of a single emitter, including the saturation as a function of the applied voltage and the emitter radius, is developed. It is shown that experimental data of field emitter arrays can be represented as the sum of these functions and the characteristic parameters can be fitted to field emission data of an array. Using this method, the values of the radii as well as the parameters of distribution models can be determined directly. Analysis of experimental data from p-type Si emitter arrays shows that only 1-2\% of the tips contribute significantly.}, language = {en} } @article{EdlerBachmannBreueretal., author = {Edler, Simon and Bachmann, Michael and Breuer, Janis and Dams, Florian and D{\"u}sberg, Felix and Hofmann, Martin and Jakšič, Jasna and Pahlke, Andreas and Langer, Christoph and Ławrowski, Robert Damian and Prommesberger, Christian and Schreiner, Rupert}, title = {Influence of adsorbates on the performance of a field emitter array in a high voltage triode setup}, series = {Journal of Applied Physics}, volume = {122}, journal = {Journal of Applied Physics}, doi = {10.1063/1.4987134}, abstract = {In the present work, black-silicon field emitter arrays (FEAs) are investigated regarding the influence of residual gas pressure on the characteristics and lifetime in the high voltage triode setup. Current-voltage-characteristics at different pressure levels are recorded and show a decreasing emission current with rising pressure. This decrease can be explained by an increase of the work function and charging of the emitter surface caused by adsorbates. The emission current can be restored to its initial value by heating of the FEA up to 110 °C during active emission. With this regeneration procedure, an extended lifetime from about 20 h to 440 h at a residual gas pressure of 10-5 mbar is achieved.}, language = {en} } @article{LangerPrommesbergerŁawrowskietal., author = {Langer, Christoph and Prommesberger, Christian and Ławrowski, Robert Damian and Schreiner, Rupert and Serbun, Pavel and M{\"u}ller, G{\"u}nter and D{\"u}sberg, Felix and Hofmann, Martin and Bachmann, Michael and Pahlke, Andreas}, title = {Field emission properties of p-type black silicon on pillar structures}, series = {Journal of Vacuum Science \& Technology B}, volume = {34}, journal = {Journal of Vacuum Science \& Technology B}, number = {2}, doi = {10.1116/1.4943919}, abstract = {Arrays of black silicon field emission pillar structures were fabricated on p-type silicon substrates. Two types of samples with the same number of pillars (arrays of 10 × 10) but different pillar heights (8 and 20 μm) were prepared as well as a black silicon reference sample without pillars. The field emission properties of these cathodes were investigated both by means of integral current-voltage measurements and by field emission scanning microscopy. Samples with a pillar height of 20 μm revealed onset fields as low as 6.4 V/μm, field enhancement factors up to 800, and emission currents up to 8 μA at an applied field of 20 V/μm. Due to the p-type material, a saturation of the emission current for fields above 11 V/μm was observed. This saturation leads to a stable operation with a current fluctuation of less than ±8\%. It was found that samples with a pillar height of 20 μm showed improved emission characteristics compared to samples with a pillar height of 8 μm or without pillars. The voltage maps revealed an increased emission homogeneity after a "burn-in" sequence of the sample. The current map showed that a few of the pillars dominate the emission. Integral current stability measurements were performed under different vacuum pressures, in order to investigate altered emission behavior and a potential degradation of the emitters. At pressures above 10-6 mbar, the sample starts to degrade irreversibly. Nevertheless, even after a harsh treatment over 30 min at 5 × 10-5 mbar and at an applied field of 23 V/μm, the cathode was still operating, and did not fail during further operation over 20 h at 5 × 10-8 mbar and at an applied field of 28 V/μm.}, language = {en} } @article{BachmannDamsDuesbergetal., author = {Bachmann, Michael and Dams, Florian and D{\"u}sberg, Felix and Hofmann, Martin and Pahlke, Andreas and Langer, Christoph and Ławrowski, Robert Damian and Prommesberger, Christian and Schreiner, Rupert and Serbun, Pavel and L{\"u}tzenkirchen-Hecht, Dirk and M{\"u}ller, G{\"u}nter}, title = {Extraction of the characteristics of current-limiting elements from field emission measurement data}, series = {Journal of Vacuum Science \& Technology B}, volume = {35}, journal = {Journal of Vacuum Science \& Technology B}, number = {2}, doi = {10.1116/1.4971768}, abstract = {In this contribution, the authors will present an algorithm to extract the characteristics of nonideal field emission circuit elements from saturation-limited field emission measurement data. The method for calculating the voltage drop on current-limiting circuit elements is based on circuit theory as well as Newton's method. Since the only assumption the authors make on the current-limiting circuit is a connection in series, this method is applicable to most field emission data showing saturation. To be able to determine the significance of any parameter output, the uncertainties of data and extracted parameters as well as the parameter correlations are fully taken into account throughout the algorithm. N-type silicon samples with varying external serial resistors are analyzed. All results show a good agreement to the nominal resistor values. Additionally, several p-type samples are analyzed, showing a diodelike behavior. The extracted current-limiting characteristics of the p-type samples are in good agreement with a pn-junction model. The stability of the emission current of the p-type samples is measured by constant voltage measurements and compared to the extracted current-limiting characteristics. The application of the algorithm to measurement data shows that the given algorithm is a valuable tool to analyze field emission measurement data influenced by nonemissive processes.}, language = {en} } @inproceedings{LangerHausladenPrommesbergeretal., author = {Langer, Christoph and Hausladen, Matthias and Prommesberger, Christian and Ławrowski, Robert Damian and Bachmann, Michael and D{\"u}sberg, Felix and Pahlke, Andreas and Shamonin (Chamonine), Mikhail and Schreiner, Rupert}, title = {Field emission current investigation of p-type and metallized silicon emitters in the frequency domain}, series = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, booktitle = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, publisher = {IEEE}, doi = {10.1109/IVNC.2018.8520127}, pages = {1-2}, abstract = {We investigated two different field emitter arrays consisting of 10×10 p-type and 10×10 undoped Au-coated high aspect ratio silicon tips. The I-V characterization of the p-type sample showed a pronounced saturation for voltages higher than 500 V and a maximum emission current of 39 nA. The metallized sample revealed a FN-like emission up to several μA. The metallized and the p-type sample operating below the saturation region showed high current fluctuations of ±16\%. Whereas, the metallized sample with current regulation and the p-type sample in the saturation yielded a current stability of ±0.4\% and ±0.3\%, respectively. Investigations in the frequency domain revealed the for field emission typical 1/f-noise. By operating in the saturation region (p-type sample) or using an emission current regulation (metallized sample) the noise level was reduced by at least 20 dB. Finally, the p-type sample was illuminated by a light emitting diode to increase and modulate the emission current in the saturation region. The emission current was increased by a factor of 3.7 to 145 nA. With this configuration we emulated an unstable emission behavior and evaluated the performance of our emission current regulation circuit.}, language = {en} } @article{PrommesbergerLangerŁawrowskietal., author = {Prommesberger, Christian and Langer, Christoph and Ławrowski, Robert Damian and Schreiner, Rupert}, title = {Investigations on the long-term performance of gated p-type silicon tip arrays with reproducible and stable field emission behavior}, series = {Journal of Vacuum Science \& Technology B}, volume = {35}, journal = {Journal of Vacuum Science \& Technology B}, number = {1}, doi = {10.1116/1.4972519}, abstract = {The authors report on the fabrication and characterization of p-type Si tip arrays with an integrated gate electrode for applications as field emission electron sources. After the reactive ion etching of the emitters, the combined thermal dry and wet oxidation was used for both the sharpening of the emitters and for the realization of an enhanced insulation layer. Au was evaporated in a self-aligned process as gate electrode. Arrays of 16 Si tips were fabricated with tip heights of about 3 μm and tip radii of about 20 nm with integrated gate electrode concentrically positioned ≈2 μm below the tip apex. Integral measurements with an additional anode showed improved field emission properties with a reproducible and stable emission behavior. A fast activation of the tips, low onset voltages of about 30 V, and moderate field emission currents up to 0.55 μA were noticed. The field emission parameters were calculated using the Fowler-Nordheim characteristics. A pronounced saturation regime was observed, and current fluctuations of less than ±1\% were investigated for 30 min. Long-term measurements were carried out for a period of more than 8 h. In the first 6 h of operation, the authors observed a drift of the emission current from 0.35 to 0.55 μA caused by an increased emission surface.}, language = {en} } @inproceedings{ŁawrowskiHausladenSchreiner, author = {Ławrowski, Robert Damian and Hausladen, Matthias and Schreiner, Rupert}, title = {Individually Addressable Fully Integrated Field Emission Electron Source Fabricated by Laser Micromachining of Silicon}, series = {33rd International Vacuum Nanoelectronics Conference (IVNC): 6-10 July 2020, Lyon}, booktitle = {33rd International Vacuum Nanoelectronics Conference (IVNC): 6-10 July 2020, Lyon}, publisher = {IEEE}, isbn = {978-1-7281-9454-7}, doi = {10.1109/IVNC49440.2020.9203470}, pages = {1 -- 2}, abstract = {A cathode with individually addressable Si tips allows the observation of the activation procedure and emission behaviour of each field emission emitter at any time of the measurement. The cathode consists of an array of 2x2 conically shaped emitter structures, which were fabricated by laser micromachining and wet etching of a Si substrate bonded on a glass carrier. Using the same process, a Si extractions grid was fabricated and mounted onto the emitter. Integral field emission measurements were performed in a diode configuration in a vacuum chamber at pressures of about 10- 9 mbar. The emitters show an onset voltage between 200 V and 300 V. The emission current for each emitter on the cathode was regulated to a given value (1.0 μA, 2.5μA, 5.0μA) by an external regulating circuit and was recorded individually during the measurement. With such approach, the relation between the emission behaviour and the geometry of emitters can be studied in detail. In addition, the current stabilization of each emitters of an array can be investigated, which led to a current stability of better than 0.5\%.}, language = {en} } @inproceedings{PrommesbergerŁawrowskiLangeretal., author = {Prommesberger, Christian and Ławrowski, Robert Damian and Langer, Christoph and Mecani, Mirgen and Huang, Yifeng and She, Juncong and Schreiner, Rupert}, title = {Field emission properties of ring-shaped Si ridges with DLC coating}, series = {Proc. SPIE 10248, Nanotechnology VIII, 102480H (30 May 2017)}, volume = {102480H}, booktitle = {Proc. SPIE 10248, Nanotechnology VIII, 102480H (30 May 2017)}, editor = {Tiginyanu (Ed.), Ion M.}, publisher = {Society of Photo-Optical Instrumentation Engineers (SPIE)}, doi = {10.1117/12.2265627}, abstract = {We report on the fabrication and the emission characterization of single ring-shaped Si ridges with a coating of diamond-like carbon (DLC). The reactive ion etching and the subsequent inductively coupled plasma step were adjusted to realize ring-shaped Si ridges with a height of 7.5 μm respectively 15 μm and an apex radius of 20 - 25 nm. The samples were coated with a DLC layer (thickness ≈ 2 - 5 nm) by a filtered cathodic vacuum arc deposition system in order to lower the work function of the emitter and to improve the field emission characteristics. The field emission characterizations were done in diode configuration with cathode and anode separated by a 50 μm thick mica spacer. A higher emission current was carried out for the ring-shaped Si ridge in comparison to the point-shaped Si tips due to the increased emission area. The highest emission current of 0.22 μA at 1000 V was measured on a DLC-coated sample with the highest aspect ratio. No degradation of the emission current was observed in the plateau regime during a measurement period of 6 h. Finally, no decreasing performance of the field emission properties was found due to changes in the geometry or destructions.}, language = {en} } @inproceedings{ŁawrowskiLangerPrommesbergeretal., author = {Ławrowski, Robert Damian and Langer, Christoph and Prommesberger, Christian and Schreiner, Rupert}, title = {Field emission from three-dimensional epitaxial grown GaN-microrods}, series = {29th International Vacuum Nanoelectronics Conference (IVNC), 2016, 11-15 July, Vancouver, BC, Canada}, booktitle = {29th International Vacuum Nanoelectronics Conference (IVNC), 2016, 11-15 July, Vancouver, BC, Canada}, publisher = {IEEE}, issn = {2380-6311}, doi = {10.1109/IVNC.2016.7551477}, pages = {87 -- 88}, abstract = {A novel three-dimensional epitaxial technique allows on patterned substrates the realization of gallium nitride pillars, also known as nano- and microrods. The typical dimensions of the microrods are in the range of one micron for the radius of the hexagonal footprint and about 10 μm in height. The microrods consist of a semiconductor heterostructure with an n GaN core, a n-GaN shell, a p GaN shell and an intermediate quantum well layer. The field emission properties were investigated in diode configuration by integral field emission measurements in a vacuum chamber at pressures around 10 -9 mbar. The spacer was mica with a thickness of 50 μm. A metallized fine-meshed nitride grid (or a metallized Si-grid) was used as anode. A current of about 1 μA at a voltage of 1250 V (1750 V) was measured. An onset field of about 12.5 MV/m (20 MV/m) and field enhancement factors in the range of 200 to 500 (150 to 300) were found. The investigation with the fine-meshed grid showed an expected pronounced saturation region.}, language = {en} } @inproceedings{PrommesbergerLangerŁawrowskietal., author = {Prommesberger, Christian and Langer, Christoph and Ławrowski, Robert Damian and Schreiner, Rupert}, title = {Field emission from black silicon structures with integrated gate electrode}, series = {29th International Vacuum Nanoelectronics Conference (IVNC), 2016, 11-15 July, Vancouver, BC, Canada}, booktitle = {29th International Vacuum Nanoelectronics Conference (IVNC), 2016, 11-15 July, Vancouver, BC, Canada}, publisher = {IEEE}, issn = {2380-6311}, doi = {10.1109/IVNC.2016.7551532}, pages = {219 -- 220}, abstract = {Black silicon structures with integrated gate electrode were realized by using an improved fabrication process. An enhanced insulation layer was achieved by a combination of dry and wet oxidation, and a gold layer was evaporated as gate electrode. The black silicon structures were prepared with a RIE/ICP etching process at room temperature. Arrays of 16 and 100 apertures with buried p-doped black silicon whiskers have been fabricated. These structures have an emitter height of approximately 1.5 μm with tip radii between 5 nm and 30 nm. The whiskers are surrounded by the gate electrode in a distance of 1.5 μm. Integral field emission measurements yielded an onset voltage of 92 V for 16 apertures and 60 V for 100 apertures for an emission current of 1 nA. Maximum emission currents up to 0.2 μA were observed for the array with 100 apertures at a cathode voltage of 200 V. Stability measurements showed a current fluctuation of ± 21\% at a mean value of the emission current of 12 nA over a period of 30 minutes for 16 apertures with b-Si whiskers.}, language = {en} } @inproceedings{ŁawrowskiLangerPrommesbergeretal., author = {Ławrowski, Robert Damian and Langer, Christoph and Prommesberger, Christian and Schreiner, Rupert}, title = {Microrods and microlines by three-dimensional epitaxially grown GaN for field emission cathodes}, series = {International Vacuum Nanoelectronics Conference (IVNC), 30th, 2017, Regensburg}, booktitle = {International Vacuum Nanoelectronics Conference (IVNC), 30th, 2017, Regensburg}, publisher = {IEEE}, doi = {10.1109/IVNC.2017.8051576}, pages = {130 -- 131}, abstract = {The three-dimensional epitaxial technique allows the realization of gallium nitride lines in addition to the rods. To optimize the properties of GaN-based field emission cathodes further investigations and an improvement of the epitaxial process were performed. The microrods and microlines consist of a one-order higher n-doped gallium nitride in comparison to the gallium nitride layer on the sapphire substrate. The typical height of the microrods and -lines is about 5 μm. The field emission properties of these structures were investigated in diode configuration by integral field emission measurements at pressures below 10 -9 mbar. For the microrods (microlines) a voltage of 1100 V (2000 V) was measured for a field emission current of about 0.5 μA with an onset field of about 12 MV/m (24 MV/m). Furthermore, the field enhancement factors for microrods and -lines are in the range of 300 and 200, respectively.}, language = {en} } @inproceedings{BachmannDamsDuesbergetal., author = {Bachmann, Michael and Dams, Florian and D{\"u}sberg, Felix and Hofmann, Martin and Pahlke, Andreas and Langer, Christoph and Ławrowski, Robert Damian and Prommesberger, Christian and Schreiner, Rupert}, title = {Extraction of the characteristics of limiting elements from field emission measurement data}, series = {29th International Vacuum Nanoelectronics Conference (IVNC), 2016, 11-15 July, Vancouver, BC, Canada}, booktitle = {29th International Vacuum Nanoelectronics Conference (IVNC), 2016, 11-15 July, Vancouver, BC, Canada}, publisher = {IEEE}, issn = {2380-6311}, doi = {10.1109/IVNC.2016.7551474}, pages = {81 -- 82}, abstract = {In this contribution we will present an algorithm to extract the characteristics of non-Fowler-Nordheim (FN) circuit elements from saturation limited field emission (FE) measurement data. The method for calculating the voltage drop on limiting circuit elements is based on circuit theory as well as Newton's method. Since no assumption on the limiting circuit is made, this method is applicable to any FE data showing saturation. To be able to determine the significance of any parameter output, the uncertainties of data and extracted parameters are fully taken into account throughout the algorithm. External serial resistors and a limiting p-doped substrate are analyzed, where the latter shows a diode-like behavior.}, language = {en} } @inproceedings{LangerPrommesbergerŁawrowskietal., author = {Langer, Christoph and Prommesberger, Christian and Ławrowski, Robert Damian and Schreiner, Rupert and Huang, Yifeng and She, Juncong}, title = {Gated p-Si field emission cathode applied in an ionization vacuum gauge}, series = {29th International Vacuum Nanoelectronics Conference (IVNC), 2016, 11-15 July, Vancouver, BC, Canada}, booktitle = {29th International Vacuum Nanoelectronics Conference (IVNC), 2016, 11-15 July, Vancouver, BC, Canada}, publisher = {IEEE}, issn = {2380-6311}, doi = {10.1109/IVNC.2016.7551500}, pages = {145 -- 146}, abstract = {A commercial Bayard-Alpert ionization vacuum gauge was equipped with a field emission electron source based on a cathode consisting of an array of 16 gated, p-doped, and DLC-coated Si-tips and characterized. An anode current of about 1.3 μA led to an ion current of 7 fA at 3×10 -7 mbar and 0.8 pA at 4×10 -5 mbar. Whereas at pressures higher than 4×10 -5 mbar the emission current of the electron source decreased, the ratio of ion and anode current remained linear. A nearly constant sensitivity of ~ 17 mbar -1 of the ionization vacuum gauge within the investigated pressure range was depicted.}, language = {en} } @inproceedings{BachmannDamsDuesbergetal., author = {Bachmann, Michael and Dams, Florian and D{\"u}sberg, Felix and Hofmann, Martin and Pahlke, Andreas and Langer, Christoph and Ławrowski, Robert Damian and Prommesberger, Christian and Schreiner, Rupert}, title = {Control of the electron source current}, series = {International Vacuum Nanoelectronics Conference (IVNC), 30th, 2017, Regensburg}, booktitle = {International Vacuum Nanoelectronics Conference (IVNC), 30th, 2017, Regensburg}, publisher = {IEEE}, doi = {10.1109/IVNC.2017.8051550}, pages = {66 -- 67}, abstract = {A control circuit to stabilize the flux of electrons transmitted through an extractor electrode is presented. By controlling the emission current a fluctuation with a standard deviation of 0.015\% is observed. However, the achievable stability of the transmitted electron current is limited due to a variation of the extraction grid current ratio showing a standard deviation of 4.33\%. By regulating the difference of the emission current and the extraction grid current an improved stability of the transmitted electron current down to a standard deviation of 0.280\% is observed. Even with operation at 2 × 10 -5 mbar a standard deviation of 0.558\% is achieved.}, language = {en} } @inproceedings{ŁawrowskiSchreinerLinghuetal., author = {Ławrowski, Robert Damian and Schreiner, Rupert and Linghu, Shuangyi and Gu, Fuxing}, title = {Field Emission Behaviour of Single-Crystal Pd Nanowires}, series = {33rd International Vacuum Nanoelectronics Conference (IVNC): 6-10 July 2020, Lyon, France}, booktitle = {33rd International Vacuum Nanoelectronics Conference (IVNC): 6-10 July 2020, Lyon, France}, publisher = {IEEE}, isbn = {978-1-7281-9454-7}, doi = {10.1109/IVNC49440.2020.9203510}, pages = {1 -- 2}, abstract = {Single-crystal Pd nanowires with typically 100 nm diameters and lengths from several micrometers to tens of micrometers were grown on Al 2 O 3 substrates in a furnace with Ar atmosphere. Integral field emission measurements of such samples after Pd coating (~10 nm) were performed in a diode configuration with a 50 μm mica spacer in a vacuum chamber at pressures of about 10 -9 mbar. The IV measurement of the sample shows an integral emission current up to 2 μA at a voltage of 500 V (10 MV/m) and an onset voltage for a current of 1 nA of about 275 V. The corresponding Fowler-Nordheim plot show a linear behavior, like expected for a metal needle.}, language = {en} } @inproceedings{PrommesbergerLangerŁawrowskietal., author = {Prommesberger, Christian and Langer, Christoph and Ławrowski, Robert Damian and Schreiner, Rupert}, title = {Benzocyclobutene as a novel integrated spacer material in a field emission electron source}, series = {International Vacuum Nanoelectronics Conference (IVNC), 30th, 2017, Regensburg}, booktitle = {International Vacuum Nanoelectronics Conference (IVNC), 30th, 2017, Regensburg}, publisher = {IEEE}, doi = {10.1109/IVNC.2017.8051605}, pages = {192 -- 193}, abstract = {For the realization of a miniaturized field emission electron source we tested benzocyclobutene (BCB) as a new spacer material between cathode and anode. We fabricated black silicon emitters and characterized the emission behavior with an integrated 5 μm thin and large-area spacer of BCB. The integrated BCB layer allows the realization of a compact electron source with only two components consisting of a cathode with BCB and a grid. The comparison with other spacer materials like polyimide (25 μm thickness) or mica (50 μm thickness) revealed for the cathode with BCB a significantly reduced operational voltage of 240 V for a field emission current of 1 μA.}, language = {en} } @inproceedings{ŁawrowskiLangerPrommesbergeretal., author = {Ławrowski, Robert Damian and Langer, Christoph and Prommesberger, Christian and Schreiner, Rupert}, title = {Light emitting diodes based on three-dimensional epitaxial grown crystalline GaN rods}, series = {7. MikroSystemTechnik Kongress "MEMS, Mikroelektronik, Systeme", 23.-25. Oktober 2017, M{\"u}nchen}, booktitle = {7. MikroSystemTechnik Kongress "MEMS, Mikroelektronik, Systeme", 23.-25. Oktober 2017, M{\"u}nchen}, publisher = {VDE-Verlag}, address = {M{\"u}nchen}, isbn = {978-3-8007-4491-6}, pages = {131 -- 134}, language = {en} } @inproceedings{LindnerBerndtTschurtschenthaletal., author = {Lindner, Matthias and Berndt, Dominik and Tschurtschenthal, Karl and Ehrlich, Ingo and Jungbauer, Bastian and Schreiner, Rupert and Pipa, Andrei V. and Hink, R{\"u}diger and Foest, R{\"u}diger and Brandenburg, Ronny and Neuwirth, Daniel and Karpen, Norbert and Bonaccurso, Elmar and Weichwald, Robert and Max, Alexander and Caspari, Ralf}, title = {Aircraft Icing Mitigation by DBD-based Micro Plasma Actuators}, series = {AIAA AVIATION 2020 FORUM: June 15-19, 2020}, booktitle = {AIAA AVIATION 2020 FORUM: June 15-19, 2020}, doi = {10.2514/6.2020-3243}, abstract = {We present the application of plasma actuators as a technology for ice prevention at airfoils. The miniaturized dielectric barrier discharge (DBD) plasma actuators (PA) were fabricated by means of microelectromechanical systems (MEMS). We elucidate how to make the actuator samples scalable and applicable to any desired shape by the use of flexible inorganic zirconia substrates. For this purpose, we applied our developed embedding method to integrate the micro actuators in modern carbon/glass fiber reinforced polymer (CFRP/GFRP) materials. Next, the embedded actuator samples were mounted on a mechanical air profile-like fixture and placed in the icing wind tunnel iCORE. The samples were tested in rime ice conditions at temperatures of -15 to -20° C and air speeds up to 30 m/s. Unlike other groups we used a thin film zirconia substrate as dielectric for the plasma actuator. Due to the low substrate thickness of just 150 µm, an operating voltage of 2 kVRMS is already sufficient enough for a stable plasma formation. The experiments show that the operated actuator was able to prevent the ice formation and first indications of a De-icing function were also found. Hence, we show that it is feasible to realize an anti-icing system with zirconia-based plasma actuators operated at lower voltages compared to conventional ones.}, language = {en} } @article{ŁawrowskiHausladenBuchneretal., author = {Ławrowski, Robert Damian and Hausladen, Matthias and Buchner, Philipp and Schreiner, Rupert}, title = {Silicon Field Emission Electron Source With Individually Controllable Single Emitters}, series = {IEEE Transactions on Electron Devices}, volume = {68}, journal = {IEEE Transactions on Electron Devices}, number = {8}, publisher = {IEEE}, doi = {10.1109/TED.2021.3093374}, pages = {4116 -- 4122}, abstract = {An electron source with an array of individually controllable single tips allows the observation of each emitter current simultaneously as well as the measurement of the integral current. Furthermore, the initial activation process of the individual tips and current distribution of the source can be examined. The Si cathode consists of an array of 2 x 2 conically shaped emitter structures on a borosilicate glass substrate. The emitters were fabricated by laser micromachining and wet etching. Integral field emission (FE) measurements were performed in a diode configuration in a vacuum chamber at pressures of about 10(-9) mbar with a self-aligned Si extraction grid, due to adjustment pins. The total emission current was regulated to a predefined value (4.0, 10, 20, 40, and 50 mu A) by an external regulating circuit and recorded individually during the measurement. The onset voltage for a current of 1 nA varied between 320 and 430 V. The voltage conversion factor is in the range of 7.6 x 10(4) cm(-1) to 1.3 x 10(5) cm(-1). Constant currentmeasurementsover a longer periodof time (1800 values with a sample rate of 0.5 Hz) were performed and show a total current fluctuation less than 0.6\% due to the regulation circuit. Despite the stable total current in regulated operation, it was observed that the individual emitters fluctuate up to 75\% for low (similar to 10(-8) A) and 5\% for high (similar to 10(-5) A) currents.}, language = {en} } @article{BachmannDuesbergPahlkeetal., author = {Bachmann, Michael and D{\"u}sberg, Felix and Pahlke, Andreas and Edler, Simon and Schels, Andreas and Herdl, Florian and Ławrowski, Robert Damian and Schreiner, Rupert}, title = {High current silicon nanowire field emitter arrays}, series = {Journal of Vacuum Science \& Technology B}, volume = {40}, journal = {Journal of Vacuum Science \& Technology B}, number = {1}, publisher = {AIP Publishing}, doi = {10.1116/6.0001639}, abstract = {Arrays of n-doped silicon nanowire field emitters with a high aspect ratio are realized by a novel dry etching technique. Compared to the high current silicon emitters in the literature, the manufacturing process is much simpler and requires only a single photolithography step and two dry etching steps. The cathodes realized with this method exhibit a total current of 20 mA from an active area of 4×4 mm2, which is significantly higher than that for most known structures made from silicon and also represents good performance in comparison with other emitter types, e.g., carbon nanotubes. In addition to characterization in ultrahigh vacuum, measurements at 10-5 mbar are performed and compared with our recent silicon emitters. Compared to these cathodes, the structures with the nanowires exhibit at least two orders of magnitude higher current-carrying capability.}, language = {en} } @article{RemskarHuettelShubinaetal., author = {Remskar, Maja and H{\"u}ttel, Andreas K. and Shubina, Tatiana V. and Seabaugh, Alan and Fathipour, Sara and Ławrowski, Robert Damian and Schreiner, Rupert}, title = {Confinement Related Phenomena in MoS2 Tubular Structures Grown from Vapour Phase}, series = {Israel Journal of Chemistry}, volume = {62}, journal = {Israel Journal of Chemistry}, number = {3-4}, publisher = {Wiley}, issn = {1869-5868}, doi = {10.1002/ijch.202100100}, pages = {1 -- 11}, abstract = {We review recently discovered phenomena observed in the MoS2 tubular structures, which were synthesized by a lasting chemical transport reaction nearly at chemical equilibrium. Such MoS2 nanotubes are distinguished by low density of structural defects, thin walls and a high aspect ratio, which intrinsically provide a confined, edge-free geometry. Quantum confinement with single electron conductance was recorded and a bright exciton photoluminescence with appearance of whispering gallery modes was observed. In addition, the field-effect transistors and field emitters based on single MoS2 nanotubes were demonstrated. These discoveries revitalize research of MoS2 curved structures grown from vapour phase, which were reported several decades ago.}, language = {en} } @inproceedings{ŁawrowskiBachmannSchreiner, author = {Ławrowski, Robert Damian and Bachmann, Michael and Schreiner, Rupert}, title = {Field Emission Arrays from Graphite Fabricated by Laser Micromachining}, series = {34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France}, booktitle = {34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France}, publisher = {IEEE}, isbn = {978-1-6654-2589-6}, doi = {10.1109/IVNC52431.2021.9600736}, pages = {1 -- 2}, abstract = {Arrays of 4x4 conical shaped emitters were directly structured by laser micromaching. Assembled as an electron source with a spacer and Si-grid, they were investigated by means of IV-measurement in ultra-high vacuum. The IV-measurements of the sample show integral emission currents up to 10 µA at a voltage of 1000 V (11 MV/m). Initially, an ideal FN-behaviour is noticeable. The deviation for higher voltage values in the FN-plot is caused by the change of the work function, which was proven by numerical calculations.}, language = {en} } @inproceedings{LindnerBerndtJungbaueretal., author = {Lindner, Matthias and Berndt, Dominik and Jungbauer, Bastian and Ehrlich, Ingo and Schreiner, Rupert and Pipa, Andrei V. and Hink, R{\"u}diger and Foest, R{\"u}diger and Brandenburg, Ronny and Max, Alexander and Caspari, Ralf}, title = {Fabrication, surface integration and testing of miniaturized dielectric barrier discharge plasma actuators for active flow control applications}, series = {AIAA Aviation 2019 Forum, 17-21 June 2019, Dallas, Texas}, booktitle = {AIAA Aviation 2019 Forum, 17-21 June 2019, Dallas, Texas}, doi = {10.2514/6.2019-2998}, language = {en} } @inproceedings{LangerŁawrowskiPrommesbergeretal., author = {Langer, Christoph and Ławrowski, Robert Damian and Prommesberger, Christian and Dams, Florian and Serbun, Pavel and Bachmann, Michael and M{\"u}ller, G{\"u}nter and Schreiner, Rupert}, title = {High aspect ratio silicon tip cathodes for application in field emission electron sources}, series = {2014 27th International Vacuum Nanoelectronics Conference (IVNC), 6-10 July 2014, Engelberg, Switzerland}, booktitle = {2014 27th International Vacuum Nanoelectronics Conference (IVNC), 6-10 July 2014, Engelberg, Switzerland}, publisher = {IEEE}, doi = {10.1109/IVNC.2014.6894824}, pages = {222 -- 223}, abstract = {Precisely aligned arrays of sharp tip structures on top of elongated pillars were realized by using an improved fabrication process including an additional inductively-coupled-plasma reactive-ion etching step. Arrays of n-type and p-type silicon with 271 tips have been fabricated and investigated. Those structures have a total height of 5-6 µm and apex radii less than 20nm. Integral field emission measurements of the arrays yielded low onset-fields in the range of 8-12V=µm and field enhancement factors between 300 and 700. The I-E curves of n-type structures showed the usual Fowler-Nordheim behaviour, whereas p-type structures revealed a significant saturation region due to the limited number of electrons in the conduction band and a further carrier depletion effect caused by the pillar. The maximum integral current in the saturation region was 150 nA at fields above 30V=µm. An excellent stability of the emission current of less than ± 2\% fluctuation was observed in the saturation region. For n-type Si a maximum integral current of 10 µA at 24V=µm and an average current stability with a fluctuation of ± 50\% were measured.}, language = {en} } @article{BachmannDuesbergLangeretal., author = {Bachmann, Michael and D{\"u}sberg, Felix and Langer, Christoph and Herdl, Florian and Bergbreiter, Lukas and Dams, Florian and Miyakawa, Natuski and Eggert, Tobias and Pahlke, Andreas and Edler, Simon and Prommesberger, Christian and Ławrowski, Robert Damian and Hausladen, Matthias and Schreiner, Rupert}, title = {Vacuum-sealed field emission electron gun}, series = {Journal of Vacuum Science \& Technology B}, volume = {38}, journal = {Journal of Vacuum Science \& Technology B}, number = {2}, publisher = {AIP Publishing}, doi = {10.1116/1.5139316}, abstract = {A compact vacuum-sealed field emission electron gun with an operation voltage below 5 kV is presented. With a 150 nm thick pyrolytic carbon membrane, a transmission of 40\% at 5 kV is obtained. For more than 2500 h of continuous operation at an emission current of 100 nA, no significant increase (<50V ) and almost no degradation were found. From this measurement, a lifetime of more than 10 000 h at continuous operation with approximately a linear increase of the extraction voltage from about 545 V to about 730 V is predicted. This electron source enables application of field emitter arrays in poor vacuum or even ambient pressure. ACKNOWLEDGMENT This work was supported by the German Federal Ministry for Economic Affairs and Energy under Project No. ZF4081502GM8. C.P., R.L., M.H., and R.S. were supported by Grant No. ZF4562901GM8.}, language = {en} } @article{LangerPrommesbergerŁawrowskietal., author = {Langer, Christoph and Prommesberger, Christian and Ławrowski, Robert Damian and Dams, Florian and Schreiner, Rupert}, title = {Simulation and Fabrication of Silicon Field Emission Cathodes for Cold Electron Sources}, series = {Advanced Materials Research}, volume = {1024}, journal = {Advanced Materials Research}, doi = {10.4028/www.scientific.net/amr.1024.48}, pages = {48 -- 51}, abstract = {We report on the simulation and fabrication of nanostructured silicon surfaces for field emission (FE) applications, e.g. ionization sensors and x-ray tubes. For the design and optimization of field-emitting silicon structures, the influence of the geometric parameters like tip height, apex radius, aperture angle and curvature shape on the field enhancement factor was investigated by simulation using finite element method. A universal geometric model which describes the real geometry of our silicon structures sufficiently accurate was taken for modeling a variety of different silicon tip structures as well as ridge structures. While a high dependency of the field enhancement on the aspect ratio and the aperture angle was found, the simulations show that the elliptic curvature affects the field enhancement only marginally. Finally, an improved process for fabrication of such silicon structures on n-type as well as p-type substrate is described, using reactive ion etching with adjustable anisotropy, wet thermal oxidation and wet etching.}, language = {en} } @article{ŁawrowskiBachmannSchreiner, author = {Ławrowski, Robert Damian and Bachmann, Michael and Schreiner, Rupert}, title = {Field emission arrays from graphite fabricated by laser micromachining}, series = {Journal of Vacuum Science \& Technology B}, volume = {40}, journal = {Journal of Vacuum Science \& Technology B}, number = {2}, publisher = {AIP Publishing}, doi = {10.1116/6.0001547}, abstract = {Laser micro structuring allows the manufacturing of conical shaped emitters on a graphitized carbon substrate without any additional treatment. Integral field emission measurements were performed in a diode configuration with a 50 µm mica spacer and a metalized Si-grid in a vacuum chamber at pressures of about 10-9 mbar. Emission currents up to 10 µA at a voltage of 1000 V (11 MV/m) with a positive current drift were observed for an array of 16 emitters. A strong modification of the emitter tip is noticeable after individual measurements. A comparable alteration of the surface is also achieved by an electrochemical treatment of the samples with a potassium hydroxide solution. However, the IV-measurements of such samples show higher onset voltages, but also higher integral emission currents. For all arrays an ideal FN behaviour is only noticeable at applied voltages below 625 V (7 MV/m). Numerical calculations indicate that the deviation in the FN-plot for higher voltage values is caused by the change of the effective work function.}, language = {en} } @article{ŁawrowskiPrommesbergerLangeretal., author = {Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Improvement of Homogenity and Aspect Ratio of Silicon Tips for Field Emission by Reactive-Ion Etching}, series = {Advances in materials science and engineering}, volume = {2014}, journal = {Advances in materials science and engineering}, publisher = {Hindawi}, doi = {10.1155/2014/948708}, abstract = {The homogeneity of emitters is very important for the performance of field emission (FE) devices. Reactive-ion etching (RIE) and oxidation have significant influences on the geometry of silicon tips. The RIE influences mainly the anisotropy of the emitters. Pressure has a strong impact on the anisotropic factor. Reducing the pressure results in a higher anisotropy, but the etch rate is also lower. A longer time of etching compensates this effect. Furthermore an improvement of homogeneity was observed. The impact of uprating is quite low for the anisotropic factor, but significant for the homogeneity. At low power the height and undercut of the emitters are more constant over the whole wafer. The oxidation itself is very homogeneous and has no observable effect on further variation of the homogeneity. This modified fabrication process allows solving the problem of inhomogeneity of previous field emission arrays.}, language = {en} } @misc{BiekerSchlaakWilfertetal., author = {Bieker, Johannes and Schlaak, Helmut F. and Wilfert, Stefan and Ławrowski, Robert Damian and Hausladen, Matthias and Schreiner, Rupert}, title = {Development of FE-based electron sources for XHVion gauges in cryogenic vacuum environments}, series = {32nd International Vacuum Nanoelectronics Conference (IVNC 2019), 22.-26.07.2019, Cincinnati, USA}, journal = {32nd International Vacuum Nanoelectronics Conference (IVNC 2019), 22.-26.07.2019, Cincinnati, USA}, language = {en} } @misc{ŁawrowskiHausladenSchreiner, author = {Ławrowski, Robert Damian and Hausladen, Matthias and Schreiner, Rupert}, title = {Individually Addressable Silicon Field Emission Cathodes Fabricated by Laser Micromachining}, series = {7th ITG International Vacuum Electronics Workshop (IVEW) 2020 and 13th International Vacuum Electron Sources Conference (IVeSC) 2020, 26. - 29.5.2020, Bad Honnef}, journal = {7th ITG International Vacuum Electronics Workshop (IVEW) 2020 and 13th International Vacuum Electron Sources Conference (IVeSC) 2020, 26. - 29.5.2020, Bad Honnef}, language = {en} } @misc{HausladenŁawrowskiSchreiner, author = {Hausladen, Matthias and Ławrowski, Robert Damian and Schreiner, Rupert}, title = {Fast Pulse Source for Field Emission Applications}, series = {7th ITG International Vacuum Electronics Workshop (IVEW) 2020 and 13th International Vacuum Electron Sources Conference (IVeSC) 2020, 26. - 29.5.2020, Bad Honnef}, journal = {7th ITG International Vacuum Electronics Workshop (IVEW) 2020 and 13th International Vacuum Electron Sources Conference (IVeSC) 2020, 26. - 29.5.2020, Bad Honnef}, language = {en} } @inproceedings{PrommesbergerLangerŁawrowskietal., author = {Prommesberger, Christian and Langer, Christoph and Ławrowski, Robert Damian and Muller, F. and Dams, Florian and Schreiner, Rupert and Serbun, Pavel and M{\"u}ller, G{\"u}nter}, title = {Comparison of integral and local field-emission properties of Mo-coated p-Si tip arrays}, series = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, booktitle = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, publisher = {IEEE}, doi = {10.1109/IVNC.2015.7225579}, pages = {192 -- 193}, abstract = {Silicon tip arrays were fabricated by means of reactive ion etching followed by oxidation for final sharpening and molybdenum thin film coating. The field-emission (FE) properties of these Mo-coated p-Si tip arrays were systemically investigated by different measurement techniques. Integral measurements in diode configuration yielded a turn-on field (for 1 nA) of 22 V/μm and nearly stable FE currents up to 6.6 μA at 38 V/μm. The effective field enhancements factor extracted from the FN plots is about 180. Detailed investigations of these FE arrays were also performed by means of field emission scanning microscopy combined with electron microscopy. A rather limited efficiency of the tips (50\% at 1500 V) and FE homogeneity (180 nA at 700 V) might be correlated with the varying morphology of the tips and the presence of oxides. Local I-V measurements of selected single tips revealed both activation and deactivation effects, which finally resulted in nearly reproducible I-V curves. Current stability measurements at a constant voltage showed rather large fluctuations (0.1-1 μA) of the FE current, which could be reduced up to 1.7\% by using of a PID-regulated voltage source. SEM images showed unchanged tip shape after the current processing.}, language = {en} } @inproceedings{ŁawrowskiLangerPrommesbergeretal., author = {Ławrowski, Robert Damian and Langer, Christoph and Prommesberger, Christian and Dams, Florian and Bachmann, Michael and Schreiner, Rupert}, title = {Fabrication and simulation of silicon structures with high aspect ratio for field emission devices}, series = {2014 27th International Vacuum Nanoelectronics Conference (IVNC), 6-10 July 2014, Engelberg, Switzerland}, booktitle = {2014 27th International Vacuum Nanoelectronics Conference (IVNC), 6-10 July 2014, Engelberg, Switzerland}, publisher = {IEEE}, doi = {10.1109/IVNC.2014.6894805}, pages = {193 -- 194}, abstract = {To obtain higher field enhancement factors of Si-tip structures, we present an improved fabrication process utilizing reactive-ion etching (RIE) with an inductively coupled plasma (ICP). In our design, a pillar under the tips is realized by a combination of RIE with ICP. With adjusted power settings (≈ 240 W) and step times (<; 5 s), vertical slopes with a low roughness of approximately 10 nm to 20 nm are possible. The remaining silicon is oxidized thermally to sharpen the emitters. A final tip radius of R <; 20 nm is obtained for the tips of the emitters. The pillar height HP can be mainly adjusted by the duration of the ICP-etching step. A total emitter height of H ≈ 6 μm with a pillar height of HP ≈ 5 μm is achieved. Simulations with COMSOL Multiphysics® are applied to calculate the field enhancement factor β. A two-dimensional model is used in rotational symmetry. In addition to the previous model, a pillar with a varying diameter {\O}P and height HP is added. A conventional emitter (H = 1 μm and R = 20 nm) placed on a pillar of the height HP ≈ 5 μm approximately results in a three times higher β-factor (β≈ 105). By decreasing the diameter {\O}P a slight increase of the β-factor is observed. However, the aspect ratio of the emitter mainly influences on the β-factor.}, language = {en} } @inproceedings{PrommesbergerLangerŁawrowskietal., author = {Prommesberger, Christian and Langer, Christoph and Ławrowski, Robert Damian and Dams, Florian and Schreiner, Rupert and Ławrowski, Robert Damian}, title = {Gated p-Si field emitter arrays for sensor applications}, series = {2015 28th International Vacuum Nanoelectronics Conference (IVNC)}, booktitle = {2015 28th International Vacuum Nanoelectronics Conference (IVNC)}, publisher = {IEEE}, doi = {10.1109/IVNC.2015.7225567}, pages = {164 -- 165}, abstract = {We report on gated p-type Si-tip array cathodes for implementation into field emission electron sources for sensor applications. Arrays of 16 and 100 tips with tip heights of 3 μm and tip radii below 30 nm with integrated gate electrodes concentrically positioned 2 μm below the tip apexes were fabricated using an improved process, which leads to an enhanced isolation layer quality with sufficient breakdown field strengths and low leakage currents. Integral measurements with a fixed grid potential of 400 V showed emission currents up to 35 μA for 100 tips at a cathode voltage of 150 V and an almost negligible parasitic gate current. The array with 16 p-type Si-tips showed a significant stabilization of the emission current in the range of 0.3 - 0.4 μA, for cathode voltages between 90 V and 150 V. The current fluctuation in this saturation regime was measured for 10 minutes and a value of less than ± 1\% was observed. No degradation of the cathode was found after 6 hours of operation at a constant cathode voltage of 100 V and a constant grid voltage of 400 V.}, language = {en} } @inproceedings{LangerPrommesbergerŁawrowskietal., author = {Langer, Christoph and Prommesberger, Christian and Ławrowski, Robert Damian and M{\"u}ller, F. and Schreiner, Rupert and Serbun, Pavel and M{\"u}ller, G{\"u}nter}, title = {Enhanced field emission from p-doped black silicon on pillar structures}, series = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, booktitle = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, publisher = {IEEE}, doi = {10.1109/IVNC.2015.7225547}, pages = {104 -- 105}, abstract = {Aligned square arrays of black silicon (b-Si) on top of pillars were fabricated on p-type silicon substrate by a deep-etching step combined with a b-Si process. Two 10×10 arrays with pillar heights of 8 μm and 20 μm and one b-Si reference sample without pillars were investigated. Integral field emission (FE) measurements of the arrays yielded rather low onset-fields between 6.4 V/μm and 13.5 V/μm and field enhancement factors between 430 and 800. The I-V curves showed typical Fowler-Nordheim behavior for low fields, whereas a saturation region was observed at higher fields. The maximum integral current in the saturation region was 8 μA at a field of 20 V/μm. The stability of the emission current was investigated over 3 hours and revealed moderate fluctuations of ± 8\% in the saturation region. Voltage scans showed well-aligned FE from nearly all pillars.}, language = {en} } @inproceedings{PrommesbergerŁawrowskiLangeretal., author = {Prommesberger, Christian and Ławrowski, Robert Damian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Realisierung von Siliziumspitzenarrays mit integrierter Gate-Elektrode f{\"u}r Anwendungen in der Vakuumsensorik}, series = {4. Landshuter Symposium Mikrosystemtechnik, Mikrosystemtechnik als Schl{\"u}sseltechnologie der Systemintegration, Tagungsband zum Symposium 12./13. M{\"a}rz 2014, Hochschule Landshut}, booktitle = {4. Landshuter Symposium Mikrosystemtechnik, Mikrosystemtechnik als Schl{\"u}sseltechnologie der Systemintegration, Tagungsband zum Symposium 12./13. M{\"a}rz 2014, Hochschule Landshut}, address = {Landshut}, isbn = {978-3-9812696-5-9}, pages = {36 -- 41}, abstract = {Bei der Feldemission (kalte Emission) k{\"o}nnen Elektronen durch ein starkes elektrisches Feld eine glatte und leitende Oberfl{\"a}che verlassen. Die Elektronen tunneln dabei durch eine Potentialbarriere, deren Breite durch ein {\"a}ußeres elektrisches Feld verkleinert wird. Durch das Hinzuf{\"u}gen einer integrierten Gate-Elektrode um eine Siliziumspitze kann die notwendige Einsatzspannung f{\"u}r Feldemission deutlich gesenkt werden. Zwischen Si-Kathode und Gate-Elektrode befindet sich dabei eine Isolationsschicht, die h{\"o}chste Anforderungen bez{\"u}glich der elektrischen Durchbruchsfestigkeit erf{\"u}llen muss. Mit einer Kombination aus Trocken- (Schichtdicke 50 nm) und Feuchtoxid (Schichtdicke 950 nm) konnte eine Isolationsschicht entwickelt werden, die im integrierten Aufbau eine minimale Durchbruchsfeldst{\"a}rke von 3,2 MV/cm aufweist. F{\"u}r die Realisierung von Siliziumkathoden mit integrierter Gate-Elektrode wurde ein bereits bestehender Herstellungsprozess um zus{\"a}tzliche Prozessschritte erweitert. Die {\"U}bertragung der lateralen Position der Spitze erfolgt durch Strukturierung des Umkehrlacks AZ5214 und einer RIE-{\"A}tzung der zuvor hergestellten SiO2-Schicht. Nach dem Entfernen der Lackschicht wird die vertikale Struktur der Siliziumspitzen durch einen RIE-{\"A}tzprozess mit den Prozessgasen SF6 und O)2 realisiert. Aus einer thermischen Oxidation bei 940 °C resultiert anschließend die Isolationsschicht zwischen Si-Kathode und Gate-Elektrode . Gleichzeitig wird diese Ansch{\"a}rfeoxidation auch zur Realisierung der endg{\"u}ltigen Spitzengeometrie verwendet. Durch die lithographische Strukturierung des Photolacks AZ5214 kann dabei die Fl{\"a}che der aufgedampften Gate-Elektrode festgelegt werden. Die Gate-Elektrode wird in einem selbstjustierenden Prozessschritt exakt konzentrisch um die Si-Spitze aufgedampft. Der gerichtete Aufdampfprozess bewirkt eine Abschattung, so dass das Oxidpl{\"a}ttchen nicht komplett von Metall ummantelt wird. Die Opferschicht aus Photolack wird mit den nicht ben{\"o}tigten Metallfl{\"a}chen in einem Lift-off-Prozess entfernt.}, language = {de} } @inproceedings{ŁawrowskiLangerPrommesbergeretal., author = {Ławrowski, Robert Damian and Langer, Christoph and Prommesberger, Christian and Dams, Florian and Serbun, Pavel and M{\"u}ller, G{\"u}nter and Schreiner, Rupert}, title = {Spitzen- und Kantenemitter aus Silizium mit einem hohen Aspektverh{\"a}ltnis f{\"u}r Ionisationsgassensoren}, series = {Mikrosystemtechnik als Schl{\"u}sseltechnologie der Systemintegration : 4. Landshuter Symposium Mikrosystemtechnik ; Tagungsband zum Symposium ; 12./13. M{\"a}rz 2014, Hochschule Landshut}, booktitle = {Mikrosystemtechnik als Schl{\"u}sseltechnologie der Systemintegration : 4. Landshuter Symposium Mikrosystemtechnik ; Tagungsband zum Symposium ; 12./13. M{\"a}rz 2014, Hochschule Landshut}, publisher = {Cluster Mikrosystemtechnik}, address = {Landshut}, isbn = {978-3-9812696-5-9}, pages = {28 -- 35}, abstract = {Durch die Optimierung von reaktivem Ionen{\"a}tzen mit induktiv gekoppeltem Plasma ist die Herstellung von verschiedenen Siliziumkathoden mit hoher Anisotropie und hohem Aspektverh{\"a}ltnis f{\"u}r Feldemissionsanwendungen m{\"o}glich. Simulationen mit COMSOL Multiphysics untermauern das Potential von solchen Spitzen- und Kantenfeldemittern. Die Ergebnisse der Simulation zeigen einen zwei- bis sechsfach h{\"o}heren Feld{\"u}berh{\"o}hungsfaktor der tiefge{\"a}tzten Strukturen im Vergleich zu identischen Emittern ohne zus{\"a}tzliche Tiefen{\"a}tzung. Feldemissionsmessungen best{\"a}tigen die Simulationsergebnisse. Der modifizierte Herstellungsprozess der Feldemitter erm{\"o}glicht somit einen zuverl{\"a}ssigen Betrieb von Feldemissionselektronenquellen bei kleineren makroskopischen Feldst{\"a}rken. Außerdem weisen die Messungen des Emissionsstroms im S{\"a}ttigungsbereich eine weitgehende Unabh{\"a}ngigkeit vom elektrischen Feld auf. Lokale Feldemissionsmessungen ergeben dadurch eine deutliche Stromstabilisierung, welche {\"u}ber große Feldst{\"a}rkenbereiche konstant bleibt. Die Nutzung der HAR-Emitter (high aspect ratio) ist damit eine gute Voraussetzung f{\"u}r einen zuverl{\"a}ssigen Betrieb der Emissionskathoden bei kleinen Feldst{\"a}rken f{\"u}r die Anwendung in Ionisationsgassensoren.}, language = {de} } @article{ŁawrowskiPrommesbergerLangeretal., author = {Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Improvement of Homogeneity and Aspect Ratio of Silicon Tips for Field Emission by Reactive-Ion Etching}, series = {Advances in Materials Science and Engineering. Special issue: Advances in Smart Materials and Applications}, volume = {2014}, journal = {Advances in Materials Science and Engineering. Special issue: Advances in Smart Materials and Applications}, publisher = {Hindawi}, issn = {1687-8442}, doi = {10.1155/2014/948708}, pages = {1 -- 6}, abstract = {The homogeneity of emitters is very important for the performance of field emission (FE) devices. Reactive-ion etching (RIE) and oxidation have significant influences on the geometry of silicon tips. The RIE influences mainly the anisotropy of the emitters. Pressure has a strong impact on the anisotropic factor. Reducing the pressure results in a higher anisotropy, but the etch rate is also lower. A longer time of etching compensates this effect. Furthermore an improvement of homogeneity was observed. The impact of uprating is quite low for the anisotropic factor, but significant for the homogeneity. At low power the height and undercut of the emitters are more constant over the whole wafer. The oxidation itself is very homogeneous and has no observable effect on further variation of the homogeneity. This modified fabrication process allows solving the problem of inhomogeneity of previous field emission arrays.}, language = {en} } @inproceedings{ŁawrowskiPrommesbergerLangeretal., author = {Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Influence of reactive ion etching parameters on the geometry of silicon tip cathodes for field emission}, series = {Applied Research Conference 2013, ARC 2013 : 17th and 18th October 2013, Deggendorf}, booktitle = {Applied Research Conference 2013, ARC 2013 : 17th and 18th October 2013, Deggendorf}, publisher = {Shaker}, address = {Aachen}, isbn = {978-3-8440-2274-2}, pages = {67 -- 69}, language = {en} } @incollection{ŁawrowskiPrommesbergerLangeretal., author = {Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Feldemissionselektronenquellen basierend auf Siliziumemittern mit hohen Aspektverh{\"a}ltnis}, series = {Forschungsbericht der OTH Regensburg 2013}, booktitle = {Forschungsbericht der OTH Regensburg 2013}, address = {Regensburg}, pages = {47 -- 48}, language = {de} }