@article{BachmannDuesbergLangeretal., author = {Bachmann, Michael and D{\"u}sberg, Felix and Langer, Christoph and Herdl, Florian and Bergbreiter, Lukas and Dams, Florian and Miyakawa, Natuski and Eggert, Tobias and Pahlke, Andreas and Edler, Simon and Prommesberger, Christian and Ławrowski, Robert Damian and Hausladen, Matthias and Schreiner, Rupert}, title = {Vacuum-sealed field emission electron gun}, series = {Journal of Vacuum Science \& Technology B}, volume = {38}, journal = {Journal of Vacuum Science \& Technology B}, number = {2}, publisher = {AIP Publishing}, doi = {10.1116/1.5139316}, abstract = {A compact vacuum-sealed field emission electron gun with an operation voltage below 5 kV is presented. With a 150 nm thick pyrolytic carbon membrane, a transmission of 40\% at 5 kV is obtained. For more than 2500 h of continuous operation at an emission current of 100 nA, no significant increase (<50V ) and almost no degradation were found. From this measurement, a lifetime of more than 10 000 h at continuous operation with approximately a linear increase of the extraction voltage from about 545 V to about 730 V is predicted. This electron source enables application of field emitter arrays in poor vacuum or even ambient pressure. ACKNOWLEDGMENT This work was supported by the German Federal Ministry for Economic Affairs and Energy under Project No. ZF4081502GM8. C.P., R.L., M.H., and R.S. were supported by Grant No. ZF4562901GM8.}, language = {en} } @article{LangerPrommesbergerŁawrowskietal., author = {Langer, Christoph and Prommesberger, Christian and Ławrowski, Robert Damian and Dams, Florian and Schreiner, Rupert}, title = {Simulation and Fabrication of Silicon Field Emission Cathodes for Cold Electron Sources}, series = {Advanced Materials Research}, volume = {1024}, journal = {Advanced Materials Research}, doi = {10.4028/www.scientific.net/amr.1024.48}, pages = {48 -- 51}, abstract = {We report on the simulation and fabrication of nanostructured silicon surfaces for field emission (FE) applications, e.g. ionization sensors and x-ray tubes. For the design and optimization of field-emitting silicon structures, the influence of the geometric parameters like tip height, apex radius, aperture angle and curvature shape on the field enhancement factor was investigated by simulation using finite element method. A universal geometric model which describes the real geometry of our silicon structures sufficiently accurate was taken for modeling a variety of different silicon tip structures as well as ridge structures. While a high dependency of the field enhancement on the aspect ratio and the aperture angle was found, the simulations show that the elliptic curvature affects the field enhancement only marginally. Finally, an improved process for fabrication of such silicon structures on n-type as well as p-type substrate is described, using reactive ion etching with adjustable anisotropy, wet thermal oxidation and wet etching.}, language = {en} } @article{ŁawrowskiBachmannSchreiner, author = {Ławrowski, Robert Damian and Bachmann, Michael and Schreiner, Rupert}, title = {Field emission arrays from graphite fabricated by laser micromachining}, series = {Journal of Vacuum Science \& Technology B}, volume = {40}, journal = {Journal of Vacuum Science \& Technology B}, number = {2}, publisher = {AIP Publishing}, doi = {10.1116/6.0001547}, abstract = {Laser micro structuring allows the manufacturing of conical shaped emitters on a graphitized carbon substrate without any additional treatment. Integral field emission measurements were performed in a diode configuration with a 50 µm mica spacer and a metalized Si-grid in a vacuum chamber at pressures of about 10-9 mbar. Emission currents up to 10 µA at a voltage of 1000 V (11 MV/m) with a positive current drift were observed for an array of 16 emitters. A strong modification of the emitter tip is noticeable after individual measurements. A comparable alteration of the surface is also achieved by an electrochemical treatment of the samples with a potassium hydroxide solution. However, the IV-measurements of such samples show higher onset voltages, but also higher integral emission currents. For all arrays an ideal FN behaviour is only noticeable at applied voltages below 625 V (7 MV/m). Numerical calculations indicate that the deviation in the FN-plot for higher voltage values is caused by the change of the effective work function.}, language = {en} } @article{ŁawrowskiPrommesbergerLangeretal., author = {Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Improvement of Homogenity and Aspect Ratio of Silicon Tips for Field Emission by Reactive-Ion Etching}, series = {Advances in materials science and engineering}, volume = {2014}, journal = {Advances in materials science and engineering}, publisher = {Hindawi}, doi = {10.1155/2014/948708}, abstract = {The homogeneity of emitters is very important for the performance of field emission (FE) devices. Reactive-ion etching (RIE) and oxidation have significant influences on the geometry of silicon tips. The RIE influences mainly the anisotropy of the emitters. Pressure has a strong impact on the anisotropic factor. Reducing the pressure results in a higher anisotropy, but the etch rate is also lower. A longer time of etching compensates this effect. Furthermore an improvement of homogeneity was observed. The impact of uprating is quite low for the anisotropic factor, but significant for the homogeneity. At low power the height and undercut of the emitters are more constant over the whole wafer. The oxidation itself is very homogeneous and has no observable effect on further variation of the homogeneity. This modified fabrication process allows solving the problem of inhomogeneity of previous field emission arrays.}, language = {en} } @misc{BiekerSchlaakWilfertetal., author = {Bieker, Johannes and Schlaak, Helmut F. and Wilfert, Stefan and Ławrowski, Robert Damian and Hausladen, Matthias and Schreiner, Rupert}, title = {Development of FE-based electron sources for XHVion gauges in cryogenic vacuum environments}, series = {32nd International Vacuum Nanoelectronics Conference (IVNC 2019), 22.-26.07.2019, Cincinnati, USA}, journal = {32nd International Vacuum Nanoelectronics Conference (IVNC 2019), 22.-26.07.2019, Cincinnati, USA}, language = {en} } @misc{ŁawrowskiHausladenSchreiner, author = {Ławrowski, Robert Damian and Hausladen, Matthias and Schreiner, Rupert}, title = {Individually Addressable Silicon Field Emission Cathodes Fabricated by Laser Micromachining}, series = {7th ITG International Vacuum Electronics Workshop (IVEW) 2020 and 13th International Vacuum Electron Sources Conference (IVeSC) 2020, 26. - 29.5.2020, Bad Honnef}, journal = {7th ITG International Vacuum Electronics Workshop (IVEW) 2020 and 13th International Vacuum Electron Sources Conference (IVeSC) 2020, 26. - 29.5.2020, Bad Honnef}, language = {en} } @misc{HausladenŁawrowskiSchreiner, author = {Hausladen, Matthias and Ławrowski, Robert Damian and Schreiner, Rupert}, title = {Fast Pulse Source for Field Emission Applications}, series = {7th ITG International Vacuum Electronics Workshop (IVEW) 2020 and 13th International Vacuum Electron Sources Conference (IVeSC) 2020, 26. - 29.5.2020, Bad Honnef}, journal = {7th ITG International Vacuum Electronics Workshop (IVEW) 2020 and 13th International Vacuum Electron Sources Conference (IVeSC) 2020, 26. - 29.5.2020, Bad Honnef}, language = {en} } @inproceedings{PrommesbergerLangerŁawrowskietal., author = {Prommesberger, Christian and Langer, Christoph and Ławrowski, Robert Damian and Muller, F. and Dams, Florian and Schreiner, Rupert and Serbun, Pavel and M{\"u}ller, G{\"u}nter}, title = {Comparison of integral and local field-emission properties of Mo-coated p-Si tip arrays}, series = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, booktitle = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, publisher = {IEEE}, doi = {10.1109/IVNC.2015.7225579}, pages = {192 -- 193}, abstract = {Silicon tip arrays were fabricated by means of reactive ion etching followed by oxidation for final sharpening and molybdenum thin film coating. The field-emission (FE) properties of these Mo-coated p-Si tip arrays were systemically investigated by different measurement techniques. Integral measurements in diode configuration yielded a turn-on field (for 1 nA) of 22 V/μm and nearly stable FE currents up to 6.6 μA at 38 V/μm. The effective field enhancements factor extracted from the FN plots is about 180. Detailed investigations of these FE arrays were also performed by means of field emission scanning microscopy combined with electron microscopy. A rather limited efficiency of the tips (50\% at 1500 V) and FE homogeneity (180 nA at 700 V) might be correlated with the varying morphology of the tips and the presence of oxides. Local I-V measurements of selected single tips revealed both activation and deactivation effects, which finally resulted in nearly reproducible I-V curves. Current stability measurements at a constant voltage showed rather large fluctuations (0.1-1 μA) of the FE current, which could be reduced up to 1.7\% by using of a PID-regulated voltage source. SEM images showed unchanged tip shape after the current processing.}, language = {en} } @inproceedings{ŁawrowskiLangerPrommesbergeretal., author = {Ławrowski, Robert Damian and Langer, Christoph and Prommesberger, Christian and Dams, Florian and Bachmann, Michael and Schreiner, Rupert}, title = {Fabrication and simulation of silicon structures with high aspect ratio for field emission devices}, series = {2014 27th International Vacuum Nanoelectronics Conference (IVNC), 6-10 July 2014, Engelberg, Switzerland}, booktitle = {2014 27th International Vacuum Nanoelectronics Conference (IVNC), 6-10 July 2014, Engelberg, Switzerland}, publisher = {IEEE}, doi = {10.1109/IVNC.2014.6894805}, pages = {193 -- 194}, abstract = {To obtain higher field enhancement factors of Si-tip structures, we present an improved fabrication process utilizing reactive-ion etching (RIE) with an inductively coupled plasma (ICP). In our design, a pillar under the tips is realized by a combination of RIE with ICP. With adjusted power settings (≈ 240 W) and step times (<; 5 s), vertical slopes with a low roughness of approximately 10 nm to 20 nm are possible. The remaining silicon is oxidized thermally to sharpen the emitters. A final tip radius of R <; 20 nm is obtained for the tips of the emitters. The pillar height HP can be mainly adjusted by the duration of the ICP-etching step. A total emitter height of H ≈ 6 μm with a pillar height of HP ≈ 5 μm is achieved. Simulations with COMSOL Multiphysics® are applied to calculate the field enhancement factor β. A two-dimensional model is used in rotational symmetry. In addition to the previous model, a pillar with a varying diameter {\O}P and height HP is added. A conventional emitter (H = 1 μm and R = 20 nm) placed on a pillar of the height HP ≈ 5 μm approximately results in a three times higher β-factor (β≈ 105). By decreasing the diameter {\O}P a slight increase of the β-factor is observed. However, the aspect ratio of the emitter mainly influences on the β-factor.}, language = {en} } @inproceedings{LangerPrommesbergerŁawrowskietal., author = {Langer, Christoph and Prommesberger, Christian and Ławrowski, Robert Damian and M{\"u}ller, F. and Schreiner, Rupert and Serbun, Pavel and M{\"u}ller, G{\"u}nter}, title = {Enhanced field emission from p-doped black silicon on pillar structures}, series = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, booktitle = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, publisher = {IEEE}, doi = {10.1109/IVNC.2015.7225547}, pages = {104 -- 105}, abstract = {Aligned square arrays of black silicon (b-Si) on top of pillars were fabricated on p-type silicon substrate by a deep-etching step combined with a b-Si process. Two 10×10 arrays with pillar heights of 8 μm and 20 μm and one b-Si reference sample without pillars were investigated. Integral field emission (FE) measurements of the arrays yielded rather low onset-fields between 6.4 V/μm and 13.5 V/μm and field enhancement factors between 430 and 800. The I-V curves showed typical Fowler-Nordheim behavior for low fields, whereas a saturation region was observed at higher fields. The maximum integral current in the saturation region was 8 μA at a field of 20 V/μm. The stability of the emission current was investigated over 3 hours and revealed moderate fluctuations of ± 8\% in the saturation region. Voltage scans showed well-aligned FE from nearly all pillars.}, language = {en} } @inproceedings{PrommesbergerŁawrowskiLangeretal., author = {Prommesberger, Christian and Ławrowski, Robert Damian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Realisierung von Siliziumspitzenarrays mit integrierter Gate-Elektrode f{\"u}r Anwendungen in der Vakuumsensorik}, series = {4. Landshuter Symposium Mikrosystemtechnik, Mikrosystemtechnik als Schl{\"u}sseltechnologie der Systemintegration, Tagungsband zum Symposium 12./13. M{\"a}rz 2014, Hochschule Landshut}, booktitle = {4. Landshuter Symposium Mikrosystemtechnik, Mikrosystemtechnik als Schl{\"u}sseltechnologie der Systemintegration, Tagungsband zum Symposium 12./13. M{\"a}rz 2014, Hochschule Landshut}, address = {Landshut}, isbn = {978-3-9812696-5-9}, pages = {36 -- 41}, abstract = {Bei der Feldemission (kalte Emission) k{\"o}nnen Elektronen durch ein starkes elektrisches Feld eine glatte und leitende Oberfl{\"a}che verlassen. Die Elektronen tunneln dabei durch eine Potentialbarriere, deren Breite durch ein {\"a}ußeres elektrisches Feld verkleinert wird. Durch das Hinzuf{\"u}gen einer integrierten Gate-Elektrode um eine Siliziumspitze kann die notwendige Einsatzspannung f{\"u}r Feldemission deutlich gesenkt werden. Zwischen Si-Kathode und Gate-Elektrode befindet sich dabei eine Isolationsschicht, die h{\"o}chste Anforderungen bez{\"u}glich der elektrischen Durchbruchsfestigkeit erf{\"u}llen muss. Mit einer Kombination aus Trocken- (Schichtdicke 50 nm) und Feuchtoxid (Schichtdicke 950 nm) konnte eine Isolationsschicht entwickelt werden, die im integrierten Aufbau eine minimale Durchbruchsfeldst{\"a}rke von 3,2 MV/cm aufweist. F{\"u}r die Realisierung von Siliziumkathoden mit integrierter Gate-Elektrode wurde ein bereits bestehender Herstellungsprozess um zus{\"a}tzliche Prozessschritte erweitert. Die {\"U}bertragung der lateralen Position der Spitze erfolgt durch Strukturierung des Umkehrlacks AZ5214 und einer RIE-{\"A}tzung der zuvor hergestellten SiO2-Schicht. Nach dem Entfernen der Lackschicht wird die vertikale Struktur der Siliziumspitzen durch einen RIE-{\"A}tzprozess mit den Prozessgasen SF6 und O)2 realisiert. Aus einer thermischen Oxidation bei 940 °C resultiert anschließend die Isolationsschicht zwischen Si-Kathode und Gate-Elektrode . Gleichzeitig wird diese Ansch{\"a}rfeoxidation auch zur Realisierung der endg{\"u}ltigen Spitzengeometrie verwendet. Durch die lithographische Strukturierung des Photolacks AZ5214 kann dabei die Fl{\"a}che der aufgedampften Gate-Elektrode festgelegt werden. Die Gate-Elektrode wird in einem selbstjustierenden Prozessschritt exakt konzentrisch um die Si-Spitze aufgedampft. Der gerichtete Aufdampfprozess bewirkt eine Abschattung, so dass das Oxidpl{\"a}ttchen nicht komplett von Metall ummantelt wird. Die Opferschicht aus Photolack wird mit den nicht ben{\"o}tigten Metallfl{\"a}chen in einem Lift-off-Prozess entfernt.}, language = {de} } @inproceedings{ŁawrowskiDemlVargheseetal., author = {Ławrowski, Robert Damian and Deml, Sonja and Varghese, T. and Schimpke, T.}, title = {Leuchtdiodenchips mit dreidimensional epitaktisch gewachsenen kristallinen GaN S{\"a}ulen}, series = {7. MikroSystemTechnik Kongress "MEMS, Mikroelektronik, Systeme", 23.-25. Oktober 2017, M{\"u}nchen}, booktitle = {7. MikroSystemTechnik Kongress "MEMS, Mikroelektronik, Systeme", 23.-25. Oktober 2017, M{\"u}nchen}, publisher = {VDE-Verlag}, address = {M{\"u}nchen}, isbn = {978-3-8007-4491-6}, pages = {131 -- 134}, abstract = {Um die Eigenschaften von Leuchtdioden zu verbessern und den Herstellungsprozess zu vereinfachen, wurde ein erweitertes Verfahren der metallorganischen Gasphasenepitaxie verwendet, um dichtgepackte dreidimensionale GaN-S{\"a}ulen mit hohen Aspektverh{\"a}ltnis auf Chipoberfl{\"a}chen zu wachsen. Diese selbstorganisierenden dreidimensionalen Strukturen sollen einerseits die lichtabstrahlende Oberfl{\"a}che der Leuchtdiode bei gleichbleibender Chipgr{\"o}ße vergr{\"o}ßern und andererseits durch die nichtpolaren Kristallebenen an den Seiten- und Deckfl{\"a}chen der S{\"a}ulen die Effizienz dieser Bauteile erh{\"o}hen. Messungen an ersten Bauteilen, die mit dieser Methode realisiert wurden, zeigen eine homogene blaue Emission bei Wellenl{\"a}ngen von 450 nm und abgestrahlte Lichtleistungen von bereits mehr als 50 mW bei Stromdichten von 120 A/cm². Diese Ergebnisse sind bereits sehr vielversprechend und lassen eine deutliche Performancesteigerung bei Optimierung der Herstellungstechnologie erwarten.}, language = {de} } @inproceedings{ŁawrowskiLangerPrommesbergeretal., author = {Ławrowski, Robert Damian and Langer, Christoph and Prommesberger, Christian and Dams, Florian and Serbun, Pavel and M{\"u}ller, G{\"u}nter and Schreiner, Rupert}, title = {Spitzen- und Kantenemitter aus Silizium mit einem hohen Aspektverh{\"a}ltnis f{\"u}r Ionisationsgassensoren}, series = {Mikrosystemtechnik als Schl{\"u}sseltechnologie der Systemintegration : 4. Landshuter Symposium Mikrosystemtechnik ; Tagungsband zum Symposium ; 12./13. M{\"a}rz 2014, Hochschule Landshut}, booktitle = {Mikrosystemtechnik als Schl{\"u}sseltechnologie der Systemintegration : 4. Landshuter Symposium Mikrosystemtechnik ; Tagungsband zum Symposium ; 12./13. M{\"a}rz 2014, Hochschule Landshut}, publisher = {Cluster Mikrosystemtechnik}, address = {Landshut}, isbn = {978-3-9812696-5-9}, pages = {28 -- 35}, abstract = {Durch die Optimierung von reaktivem Ionen{\"a}tzen mit induktiv gekoppeltem Plasma ist die Herstellung von verschiedenen Siliziumkathoden mit hoher Anisotropie und hohem Aspektverh{\"a}ltnis f{\"u}r Feldemissionsanwendungen m{\"o}glich. Simulationen mit COMSOL Multiphysics untermauern das Potential von solchen Spitzen- und Kantenfeldemittern. Die Ergebnisse der Simulation zeigen einen zwei- bis sechsfach h{\"o}heren Feld{\"u}berh{\"o}hungsfaktor der tiefge{\"a}tzten Strukturen im Vergleich zu identischen Emittern ohne zus{\"a}tzliche Tiefen{\"a}tzung. Feldemissionsmessungen best{\"a}tigen die Simulationsergebnisse. Der modifizierte Herstellungsprozess der Feldemitter erm{\"o}glicht somit einen zuverl{\"a}ssigen Betrieb von Feldemissionselektronenquellen bei kleineren makroskopischen Feldst{\"a}rken. Außerdem weisen die Messungen des Emissionsstroms im S{\"a}ttigungsbereich eine weitgehende Unabh{\"a}ngigkeit vom elektrischen Feld auf. Lokale Feldemissionsmessungen ergeben dadurch eine deutliche Stromstabilisierung, welche {\"u}ber große Feldst{\"a}rkenbereiche konstant bleibt. Die Nutzung der HAR-Emitter (high aspect ratio) ist damit eine gute Voraussetzung f{\"u}r einen zuverl{\"a}ssigen Betrieb der Emissionskathoden bei kleinen Feldst{\"a}rken f{\"u}r die Anwendung in Ionisationsgassensoren.}, language = {de} } @article{ŁawrowskiPrommesbergerLangeretal., author = {Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Improvement of Homogeneity and Aspect Ratio of Silicon Tips for Field Emission by Reactive-Ion Etching}, series = {Advances in Materials Science and Engineering. Special issue: Advances in Smart Materials and Applications}, volume = {2014}, journal = {Advances in Materials Science and Engineering. Special issue: Advances in Smart Materials and Applications}, publisher = {Hindawi}, issn = {1687-8442}, doi = {10.1155/2014/948708}, pages = {1 -- 6}, abstract = {The homogeneity of emitters is very important for the performance of field emission (FE) devices. Reactive-ion etching (RIE) and oxidation have significant influences on the geometry of silicon tips. The RIE influences mainly the anisotropy of the emitters. Pressure has a strong impact on the anisotropic factor. Reducing the pressure results in a higher anisotropy, but the etch rate is also lower. A longer time of etching compensates this effect. Furthermore an improvement of homogeneity was observed. The impact of uprating is quite low for the anisotropic factor, but significant for the homogeneity. At low power the height and undercut of the emitters are more constant over the whole wafer. The oxidation itself is very homogeneous and has no observable effect on further variation of the homogeneity. This modified fabrication process allows solving the problem of inhomogeneity of previous field emission arrays.}, language = {en} } @inproceedings{ŁawrowskiPrommesbergerLangeretal., author = {Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Influence of reactive ion etching parameters on the geometry of silicon tip cathodes for field emission}, series = {Applied Research Conference 2013, ARC 2013 : 17th and 18th October 2013, Deggendorf}, booktitle = {Applied Research Conference 2013, ARC 2013 : 17th and 18th October 2013, Deggendorf}, publisher = {Shaker}, address = {Aachen}, isbn = {978-3-8440-2274-2}, pages = {67 -- 69}, language = {en} } @incollection{ŁawrowskiPrommesbergerLangeretal., author = {Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert}, title = {Feldemissionselektronenquellen basierend auf Siliziumemittern mit hohen Aspektverh{\"a}ltnis}, series = {Forschungsbericht der OTH Regensburg 2013}, booktitle = {Forschungsbericht der OTH Regensburg 2013}, address = {Regensburg}, pages = {47 -- 48}, language = {de} } @misc{WeberDendorferSuessetal., author = {Weber, Karsten and Dendorfer, Sebastian and S{\"u}ß, Franz and Kubowitsch, Simone and Schratzenstaller, Thomas and Haug, Sonja and Mohr, Christa and Kiesl, Hans and Drechsler, J{\"o}rg and Westner, Markus and Kobus, J{\"o}rn and Schubert, Martin J. W. and Zenger, Stefan and Pietsch, Alexander and Weiß, Josef and Hinterseer, Sebastian and Schieck, Roland and Scherzinger, Stefanie and Klettke, Meike and Ringlstetter, Andreas and St{\"o}rl, Uta and Bissyand{\´e}, Tegawend{\´e} F. and Seeburger, Achim and Schindler, Timo and Ramsauer, Ralf and Kiszka, Jan and K{\"o}lbl, Andreas and Lohmann, Daniel and Mauerer, Wolfgang and Maier, Johannes and Scorna, Ulrike and Palm, Christoph and Soska, Alexander and Mottok, J{\"u}rgen and Ellermeier, Andreas and V{\"o}gele, Daniel and Hierl, Stefan and Briem, Ulrich and Buschmann, Knut and Ehrlich, Ingo and Pongratz, Christian and Pielmeier, Benjamin and Tyroller, Quirin and Monkman, Gareth J. and Gut, Franz and Roth, Carina and Hausler, Peter and Bierl, Rudolf and Prommesberger, Christian and Ławrowski, Robert Damian and Langer, Christoph and Schreiner, Rupert and Huang, Yifeng and She, Juncong and Ottl, Andreas and Rieger, Walter and Kraml, Agnes and Poxleitner, Thomas and Hofer, Simon and Heisterkamp, Benjamin and Lerch, Maximilian and Sammer, Nike and Golde, Olivia and Wellnitz, Felix and Schmid, Sandra and Muntschick, Claudia and Kusterle, Wolfgang and Paric, Ivan and Br{\"u}ckl, Oliver and Haslbeck, Matthias and Schmidt, Ottfried and Schwanzer, Peter and Rabl, Hans-Peter and Sterner, Michael and Bauer, Franz and Steinmann, Sven and Eckert, Fabian and Hofrichter, Andreas}, title = {Forschungsbericht 2017}, editor = {Baier, Wolfgang}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg}, isbn = {978-3-9818209-3-5}, doi = {10.35096/othr/pub-1383}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-13835}, subject = {Forschung}, language = {de} } @inproceedings{BachmannDamsDuesbergetal., author = {Bachmann, Michael and Dams, Florian and D{\"u}sberg, F. and Hofmann, Martin and Pahlke, Andreas and Langer, Christoph and Ławrowski, Robert Damian and Prommesberger, Christian and Schreiner, Rupert}, title = {Stability investigation of high aspect ratio n-type silicon field emitter arrays}, series = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, booktitle = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, publisher = {IEEE}, doi = {10.1109/IVNC.2015.7225584}, pages = {204 -- 205}, abstract = {Electron sources based on silicon field emitter arrays, produced in processes based on semiconductor technology, are good candidates for a miniaturized X-ray source. A key parameter for this application is the stability of the X-ray photon flux and, thus, the emission current. In the present work we have investigated the influence of the residual gas pressure and a resistor in series on the emission stability of a high aspect ratio n-type silicon emitter array with hybrid extraction electrode. An increase of current fluctuations was found for pressures above 10-6 mbar. High resistances in series to the emitter array alter the emission characteristics, but greatly suppress spikes in the emission current and improve its stability. This, however, strongly depends on the bias point. The field enhancement factor is not affected by the resistance. In a long term measurement the emission current was found to be constant after an initial phase of degradation.}, language = {en} } @article{ŁawrowskiPirkerKanekoetal., author = {Ławrowski, Robert Damian and Pirker, Luka and Kaneko, Keita and Kokubo, Hiroki and Bachmann, Michael and Ikuno, Takashi and Remskar, Maja and Schreiner, Rupert}, title = {Field emission from nanotubes and flakes of transition metal dichalcogenides}, series = {Journal of Vacuum Science and Technology B}, volume = {38}, journal = {Journal of Vacuum Science and Technology B}, number = {3}, publisher = {AIP Publishing}, doi = {10.1116/1.5140474}, pages = {032801}, abstract = {Transition metal dichalcogenides such as MoS2 and WS2 are low-dimensional semiconductor materials. MoS2 and WS2 nanotubes and flakes were grown by a chemical transport reaction under a temperature gradient. I2 was used as a transport agent for previously synthesized MoS2 and WS2, respectively. These multilayered nanotubes are indirect bandgap semiconductors with a bandgap depending on their diameter. WS2 flakes were prepared by the sulfurization of thin WOx flakes. To increase the field enhancement of such low-dimensional structures by a higher aspect ratio, two approaches were examined: (a) the MoS2 and WS2 nanotubes were attached individually by a focused ion beam with Pt on dry etched n-type Si pillars and (b) the WS2 flakes were grown directly on the surface of the (n-type and p-type) Si pillars. Integral field emission measurements were performed in a diode configuration with a 50 μm mica spacer in a vacuum chamber at pressures of about 10-9 mbar. At a voltage of 900 V (18 MV/m), the integral emission current from the nanotubes is up to 11 μA for the lateral mounted MoS2 and about 1.3 μA (1.0 μA) for the upright mounted WS2 (MoS2). The onset voltage for a current of 1 nA is about 550 V for MoS2 and 500 V for WS2, respectively. The voltage conversion factor is in the range of 6 × 104-8 × 104 cm-1 for the nanotubes. The mounted MoS2 flakes show a field emission current of about 6 μA at 18 MV/m in contrast to the directly grown WS2 flakes, which show a pronounced saturation regime and, therefore, a lower emission current of about 0.5 μA is reached at 1500 V (25 MV/m). The WS2 flakes show a two times higher (1 × 105 cm-1) voltage conversion factor in comparison to the MoS2 flakes (5 × 104 cm-1). The extracted characteristics of the current-limiting part show a difference in the behavior of the extracted current-limiting characteristics between the lateral (linear) and upright mounted (exponential) nanotubes and the MoS2 flakes. In contrast, the WS2 flakes show charge carrier depletion effects.}, language = {en} } @inproceedings{SerbunPorshynMuelleretal., author = {Serbun, Pavel and Porshyn, Vitali and M{\"u}ller, G{\"u}nter and L{\"u}tzenkirchen-Hecht, Dirk and Prommesberger, Christian and Langer, Christoph and Ławrowski, Robert Damian and Schreiner, Rupert}, title = {Field emission behavior of single n- and p-type black Si pillar structures}, series = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, booktitle = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, publisher = {IEEE}, doi = {10.1109/IVNC.2018.8520292}, pages = {1-2}, abstract = {We have investigated the properties of single n- and p-type black silicon (b-Si) pillars with a height of 20 μ m under strong electric field and halogen lamp or laser illumination. For both type of b-Si pillar structures, I-V measurements revealed strong activation effects, which consisted in sudden current increases during the first up/down voltage sweeps. The maximum reproducible emission current from a single n-type b-Si pillar structure was about 15 μ A. A pronounced saturation region at 240 nA was observed for a single p-type b-Si pillar. The current fluctuation over time showed a standard deviation of 28\% and 2.5\% for n- and p-type single b-Si pillar structures, respectively. Optical switching under halogen lamp illumination resulted in at least 3 times higher saturation currents and showed a linear dependence of the FE current on the laser power.}, language = {en} }