@article{ŁawrowskiPirkerKanekoetal., author = {Ławrowski, Robert Damian and Pirker, Luka and Kaneko, Keita and Kokubo, Hiroki and Bachmann, Michael and Ikuno, Takashi and Remskar, Maja and Schreiner, Rupert}, title = {Field emission from nanotubes and flakes of transition metal dichalcogenides}, series = {Journal of Vacuum Science and Technology B}, volume = {38}, journal = {Journal of Vacuum Science and Technology B}, number = {3}, publisher = {AIP Publishing}, doi = {10.1116/1.5140474}, pages = {032801}, abstract = {Transition metal dichalcogenides such as MoS2 and WS2 are low-dimensional semiconductor materials. MoS2 and WS2 nanotubes and flakes were grown by a chemical transport reaction under a temperature gradient. I2 was used as a transport agent for previously synthesized MoS2 and WS2, respectively. These multilayered nanotubes are indirect bandgap semiconductors with a bandgap depending on their diameter. WS2 flakes were prepared by the sulfurization of thin WOx flakes. To increase the field enhancement of such low-dimensional structures by a higher aspect ratio, two approaches were examined: (a) the MoS2 and WS2 nanotubes were attached individually by a focused ion beam with Pt on dry etched n-type Si pillars and (b) the WS2 flakes were grown directly on the surface of the (n-type and p-type) Si pillars. Integral field emission measurements were performed in a diode configuration with a 50 μm mica spacer in a vacuum chamber at pressures of about 10-9 mbar. At a voltage of 900 V (18 MV/m), the integral emission current from the nanotubes is up to 11 μA for the lateral mounted MoS2 and about 1.3 μA (1.0 μA) for the upright mounted WS2 (MoS2). The onset voltage for a current of 1 nA is about 550 V for MoS2 and 500 V for WS2, respectively. The voltage conversion factor is in the range of 6 × 104-8 × 104 cm-1 for the nanotubes. The mounted MoS2 flakes show a field emission current of about 6 μA at 18 MV/m in contrast to the directly grown WS2 flakes, which show a pronounced saturation regime and, therefore, a lower emission current of about 0.5 μA is reached at 1500 V (25 MV/m). The WS2 flakes show a two times higher (1 × 105 cm-1) voltage conversion factor in comparison to the MoS2 flakes (5 × 104 cm-1). The extracted characteristics of the current-limiting part show a difference in the behavior of the extracted current-limiting characteristics between the lateral (linear) and upright mounted (exponential) nanotubes and the MoS2 flakes. In contrast, the WS2 flakes show charge carrier depletion effects.}, language = {en} } @inproceedings{SerbunPorshynMuelleretal., author = {Serbun, Pavel and Porshyn, Vitali and M{\"u}ller, G{\"u}nter and L{\"u}tzenkirchen-Hecht, Dirk and Prommesberger, Christian and Langer, Christoph and Ławrowski, Robert Damian and Schreiner, Rupert}, title = {Field emission behavior of single n- and p-type black Si pillar structures}, series = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, booktitle = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, publisher = {IEEE}, doi = {10.1109/IVNC.2018.8520292}, pages = {1-2}, abstract = {We have investigated the properties of single n- and p-type black silicon (b-Si) pillars with a height of 20 μ m under strong electric field and halogen lamp or laser illumination. For both type of b-Si pillar structures, I-V measurements revealed strong activation effects, which consisted in sudden current increases during the first up/down voltage sweeps. The maximum reproducible emission current from a single n-type b-Si pillar structure was about 15 μ A. A pronounced saturation region at 240 nA was observed for a single p-type b-Si pillar. The current fluctuation over time showed a standard deviation of 28\% and 2.5\% for n- and p-type single b-Si pillar structures, respectively. Optical switching under halogen lamp illumination resulted in at least 3 times higher saturation currents and showed a linear dependence of the FE current on the laser power.}, language = {en} } @inproceedings{SerbunPorshynMuelleretal., author = {Serbun, Pavel and Porshyn, Vitali and M{\"u}ller, G{\"u}nter and Mingels, Stephan and L{\"u}tzenkirchen-Hecht, Dirk and Bachmann, Michael and D{\"u}sberg, Felix and Dams, Florian and Hofmann, Martin and Pahlke, Andreas and Prommesberger, Christian and Langer, Christoph and Ławrowski, Robert Damian and Schreiner, Rupert}, title = {Field emission behavior of Au-tip-coated p-type Si pillar structures}, series = {29th International Vacuum Nanoelectronics Conference (IVNC), 2016, 11-15 July, Vancouver, BC, Canada}, booktitle = {29th International Vacuum Nanoelectronics Conference (IVNC), 2016, 11-15 July, Vancouver, BC, Canada}, publisher = {IEEE}, issn = {2380-6311}, doi = {10.1109/IVNC.2016.7551516}, pages = {181 -- 182}, abstract = {Precisely aligned high-aspect-ratio (HAR) silicon tip arrays were fabricated using enhanced reactive ion etching with an inductively-coupled-plasma followed by a sharpening oxidation. A gold thin film was then sputtered only on the tips of the HAR structures. Field-emission (FE) properties from Au-coated HAR p-Si tip array cathodes have been systematically investigated by means of field emission scanning microscopy (FESM). A rather high efficiency of the HAR Si structures (71\% at 550 V), but limited homogeneous FE with currents of 1-600 nA might be correlated with the varying geometry of the tips and the presence of oxides. I-V measurements of single Au-coated HAR emitters revealed activation effects and the saturation current region at 3 nA. An increase of the saturation current by 4 orders of magnitude was observed during 20 hours of conditioning at constant voltage, which finally resulted in nearly reproducible FN curves with a ß-factor of 473. An excellent stability of the emission current of less than 1 \% was obtained during the additional long-time conditioning at constant voltage. Optical switching under halogen lamp illumination resulted in at least 2 times higher saturation currents and showed a linear dependence of the FE current on the light color temperature.}, language = {en} } @inproceedings{SerbunPorshynLuetzenkirchenHechtetal., author = {Serbun, Pavel and Porshyn, Vitali and L{\"u}tzenkirchen-Hecht, Dirk and Prommesberger, Christian and Langer, Christoph and Ławrowski, Robert Damian and Schreiner, Rupert}, title = {Photosensitivity of single silicon high-aspect-ratio tips with different doping levels}, series = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, booktitle = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, publisher = {IEEE}, doi = {10.1109/IVNC.2018.8520288}, pages = {1-2}, abstract = {Photosensitivity of single lightly p-doped, highly p-doped, with an integrated p/n junction and intrinsic high-aspect-ratio (HAR) silicon tips was investigated in an ultra-high vacuum environment. The current-voltage characteristics (I-V) of the lightly doped p-type HAR tips showed a characteristic current saturation at around 10-12 nA, whereas the HAR Si tips with p/n junction showed similar saturation phenomena, however, at much smaller current values starting at ~20-30 pA. Optical switching under a halogen lamp illumination resulted in at least 2-4 times higher saturation currents and showed a linear dependence between the illumination power and the FE current, for both types of structures. In case of the highly p-doped HAR tips optical current switching effects, i. e. current saturation, were observed at rather low current levels 1-2 pA. Intrinsic HAR Si-tips showed relative unstable field emission behavior without a clear evidence of the photosensitivity.}, language = {en} } @inproceedings{SchreinerLangerPrommesbergeretal., author = {Schreiner, Rupert and Langer, Christoph and Prommesberger, Christian and Ławrowski, Robert Damian and Dams, Florian and Bachmann, Michael and D{\"u}sberg, F. and Hofmann, Martin and Pahlke, Andreas and Serbun, Pavel and Mingels, Stephan and M{\"u}ller, G{\"u}nter}, title = {Semiconductor field emission electron sources using a modular system concept for application in sensors and x-ray-sources}, series = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, booktitle = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, publisher = {IEEE}, doi = {10.1109/IVNC.2015.7225572}, pages = {178 -- 179}, abstract = {Semiconductor field emitters are suitable candidates for applications, which require a very stable field emission (FE) current and a high emission uniformity over the entire emission area. By using different materials and geometries, we are able to vary the FE characteristics within a wide range. Each specific application requires its own optimized design for the cathode as well as for the other parts of the FE electron source. To meet as many of these requirements as possible while using only a limited number of different prefabricated components, we established a modular system concept for our FE electron source. This allows the implementation of almost every cathode material. For first characterizations, we used gated p-type Si cathodes with 16 tips. We obtained stable FE currents of 0.4 μA for a grid-potential of 400 V and a gate potential of 100 V. Almost 100\% of the electrons are emitted towards the grid-electrode. Parasitic leakage paths, as well as the electron emission towards the gate-electrode can be neglected. Approximately 10\% of the electrons are transmitted through the grid and reach the external anode. This is in good agreement with the optical transmission through the grid-mesh.}, language = {en} } @inproceedings{ŁawrowskiLangerPrommesbergeretal., author = {Ławrowski, Robert Damian and Langer, Christoph and Prommesberger, Christian and Schreiner, Rupert and Mingels, Stephan and Porshyn, Vitali and Serbun, Pavel and M{\"u}ller, G{\"u}nter}, title = {Field emission from surface textured GaN with buried double-heterostructures}, series = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, booktitle = {2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China}, publisher = {IEEE}, doi = {10.1109/IVNC.2015.7225548}, pages = {106 -- 107}, abstract = {In this contribution we report on field emission (FE) cathodes based on thin-film LED-technology and surface texturing. The FE cathode can be used both as an n-GaN cathode with an electrical contact at the top side metallization as well as a pn-GaN diode contacting only the p-GaN layer at the bottom side of the structure. The local and integral FE properties of the textured surface of the LED structure were investigated. For n-GaN an integral emission current up to 1.0 μA at an electric field of 19 V/μm was achieved. The pn-GaN diode measurements showed an integral current saturation behavior with two orders of magnitude lower FE currents. Regulated voltage scans obtained by FE scanning microscopy revealed a well-distributed emission over the whole cathode area. Measurements under pulsed tunable laser illumination and moderate electric fields indicated charge carrier generation in the buried double-heterostructures at photon energies below 3.5 eV besides normal photoemission above 4.1 eV.}, language = {en} } @article{PirkerŁawrowskiSchreineretal., author = {Pirker, Luka and Ławrowski, Robert Damian and Schreiner, Rupert and Remškar, Maja and Višić, Bojana}, title = {MoₓWₓ₋₁S₂ Nanotubes for Advanced Field Emission Application}, series = {Advanced Functional Materials}, journal = {Advanced Functional Materials}, publisher = {Wiley}, issn = {1616-3028}, doi = {10.1002/adfm.202213869}, pages = {1 -- 8}, abstract = {Transition metal dichalcogenide (TMDC) nanotubes complement the field of low-dimensional materials with their quasi-1D morphology and a wide set of intriguing properties. By introducing different transition metals into the crystal structure, their properties can be tailored for specific purpose and applications. Herein, the characterization and a subsequent preparation of single-nanotube field emission devices of MoxWx-1S2 nanotubes prepared via the chemical vapor transport reaction is presented. Energy-dispersive X-ray spectroscopy, Raman spectroscopy, and X-ray diffraction indicate that the molybdenum and tungsten atoms are randomly distributed within the crystal structure and that the material is highly crystalline. High resolution transmission electron microscopy and electron diffraction (ED) patterns further corroborate these findings. A detailed analysis of the ED patterns from an eight-layer nanotube reveal that the nanotubes grow in the 2H structure, with each shell consists of one bilayer. The work function of the nanotubes is comparable to that of pure MoS2 and lower of pure WS2 NTs, making them ideal candidates for field emission applications. Two devices with different geometrical setup are prepared and tested as field emitters, showing promising results for single nanotube field emission applications.}, language = {en} } @misc{BroserFalterŁawrowskietal., author = {Broser, Christian and Falter, Thomas and Ławrowski, Robert Damian and Altenbuchner, Amelie and V{\"o}gele, Daniel and Koss, Claus and Schlamp, Matthias and Dunnweber, Jan and Steffens, Oliver and Heckner, Markus and Jaritz, Sabine and Schiegl, Thomas and Corsten, Sabine and Lauer, Norina and Guertler, Katherine and Koenig, Eric and Haug, Sonja and Huber, Dominik and Birkenmaier, Clemens and Krenkel, Lars and Wagner, Thomas and Justus, Xenia and Saßmannshausen, Sean Patrick and Kleine, Nadine and Weber, Karsten and Braun, Carina N. and Giacoppo, Giuliano and Heinrich, Michael and Just, Tobias and Schreck, Thomas and Schnabl, Andreas and Gilmore, Amador T{\´e}ran and Roeslin, Samuel and Schmid, Sandra and Wellnitz, Felix and Malz, Sebastian and Maurial, Andreas and Hauser, Florian and Mottok, J{\"u}rgen and Klettke, Meike and Scherzinger, Stefanie and St{\"o}rl, Uta and Heckner, Markus and Bazo, Alexander and Wolff, Christian and Kopper, Andreas and Westner, Markus and Pongratz, Christian and Ehrlich, Ingo and Briem, Ulrich and Hederer, Sebastian and Wagner, Marcus and Schillinger, Moritz and G{\"o}rlach, Julien and Hierl, Stefan and Siegl, Marco and Langer, Christoph and Hausladen, Matthias and Schreiner, Rupert and Haslbeck, Matthias and Kreuzer, Reinhard and Br{\"u}ckl, Oliver and Dawoud, Belal and Rabl, Hans-Peter and Gamisch, Bernd and Schmidt, Ottfried and Heberl, Michael and G{\"a}nsbauer, Bianca and Bick, Werner and Ellermeier, Andreas and Monkman, Gareth J. and Prem, Nina and Sindersberger, Dirk and Tschurtschenthaler, Karl and Aurbach, Maximilian and Dendorfer, Sebastian and Betz, Michael A. and Szecsey, Tamara and Mauerer, Wolfgang and Murr, Florian}, title = {Forschung 2018}, editor = {Baier, Wolfgang}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg}, isbn = {978-3-9818209-5-9}, doi = {10.35096/othr/pub-1382}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-13826}, pages = {98}, subject = {Forschung}, language = {de} } @inproceedings{ŁawrowskiLangerSchreineretal., author = {Ławrowski, Robert Damian and Langer, Christoph and Schreiner, Rupert and Sellmair, Josef}, title = {Nano Emitters on Silicon Pillar Structures generated by a Focused Electron Beam Induced Deposition}, series = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, booktitle = {International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan}, publisher = {IEEE}, doi = {10.1109/IVNC.2018.8520059}, pages = {1-2}, abstract = {Nano emitters were deposited by focused electron beam induced deposition of Trimethyl-(methylcyclopentadienyl)platinum(IV) on top of silicon pillars. The nano emitters were exactly positioned in the center on the top of up to four pillars of a quadratic arranged array of sixteen pillars with a pitch of 50 μm. Integral field emission measurements were performed in a diode configuration with a 50 μm mica spacer in a vacuum chamber at pressures of about 10 -9 mbar. The Fowler-Nordheim plots show a linear behavior, like expected for an n-type silicon material and a metal needle. The I-V measurement of the most promising sample shows an integral emission current up to 2 μm at a voltage of 600 V (12 MV/m) and an onset voltage for a current of 1 nA of about 300 V.}, language = {en} }