@article{StichelLaumerBaumuelleretal., author = {Stichel, Thomas and Laumer, Tobias and Baum{\"u}ller, Tobias and Amend, Philipp and Roth, Stephan}, title = {Powder Layer Preparation Using Vibration-controlled Capillary Steel Nozzles for Additive Manufacturing}, series = {Physics Procedia}, volume = {56}, journal = {Physics Procedia}, publisher = {Elsevier}, issn = {1875-3892}, doi = {10.1016/j.phpro.2014.08.158}, pages = {157 -- 166}, abstract = {In this report, the dry delivery of polyamide 12 powders by vibrating capillary steel nozzles is investigated and discussed regarding its potential for powder layer preparation in Laser Beam Melting. Therefore, a setup including a steel nozzle assembled on a piezoelectric actuator is presented, which enables the precise control over very small powder quantities by vibration excitation. An analysis reveals that the mass flow through the nozzle can be adjusted by the vibration modes in a certain range depending on the nozzle's specifications, whereas the vibration modes themselves show a complicated behaviour. Using a positioning system in combination with the vibrating nozzle, single-layer patterns consisting of polyamide 12 are produced and characterized regarding surface homogeneity and selectivity using a laser stripe sensor.}, language = {en} } @article{StichelLaumerLinnenweberetal., author = {Stichel, Thomas and Laumer, Tobias and Linnenweber, Tim and Amend, Philipp and Roth, Stephan}, title = {Mass Flow Characterization of Selective Deposition of Polymer Powders with Vibrating Nozzles for Laser Beam Melting of Multi-material Components}, series = {Physics Procedia}, volume = {83}, journal = {Physics Procedia}, publisher = {Elsevier}, address = {Amsterdam [u.a.]}, issn = {1875-3892}, doi = {10.1016/j.phpro.2016.08.099}, pages = {947 -- 953}, abstract = {The generation of multi-material components by laser beam melting (LBM) is a challenge which requires the invention of new coating devices for preparation of arbitrary powder patterns. One solution is the usage of vibration-controlled nozzles for selective deposition of polymer powders. Powder flow can be initiated by vibration enabling a start-stop function without using any mechanical shutter. In this report, the delivery of polymer powder by vibrating nozzles is investigated with respect to their application in LBM machines. Therefore, a steel nozzle attached to a piezo actor and a weighing cell is used in order to measure the stability and time-dependence of the powder mass flow upon vibration excitation with the usage of different kind of powder formulations. The results show that precompression of the powder inside the nozzle by vibration excitation is essential to realize a reliable start-stop function with reproducible discharge cyles and to prevent a initial flush of powder flow. Moreover, the use of different powder materials showed that mass flow is even possible with powders which are not optimized regarding flowability, but is readily enhanced with a factor of 2 to 3 by admixing Aerosil® fumed silica.}, language = {en} } @article{LaunhardtWoerzLodereretal., author = {Launhardt, M. and W{\"o}rz, A. and Loderer, A. and Laumer, Tobias and Drummer, Dietmar and Hausotte, Tino and Schmidt, M.}, title = {Detecting surface roughness on SLS parts with various measuring techniques}, series = {Polymer Testing}, volume = {53}, journal = {Polymer Testing}, publisher = {Elsevier}, address = {Amsterdam}, isbn = {0142-9418}, issn = {1873-2348}, doi = {10.1016/j.polymertesting.2016.05.022}, pages = {217 -- 226}, abstract = {Selective Laser Sintering (SLS) is an additive manufacturing technique whereby a laser melts polymer powder layer by layer to generate three-dimensional parts. It enables the fabrication of parts with high degrees of complexity, nearly no geometrical restrictions, and without the necessity of a tool or a mold. Due to the orientation in the building space, the processing parameters, and the powder properties, the resulting parts possess an increased surface roughness. In comparison to other manufacturing techniques, e.g. injection molding, the surface roughness of SLS parts results from partially melted powder particles on the surface layer. The actual surface roughness must thus be characterized with respect to the part's eventual application. At the moment, there is no knowledge regarding which measuring technique is most suitable for detecting and quantifying SLS parts' surface roughness. The scope of this paper is to compare tactile profile measurement methods, as established in industry, to optical measurement techniques such as Focus Variation, Fringe Projection Technique (FPT), and Confocal Laser Scanning Microscope (CLSM). The advantages and disadvantages of each method are presented and, additionally, the effect of tactile measurement on a part's surface is investigated.}, language = {en} } @inproceedings{LaumerSchmidtStichel, author = {Laumer, Tobias and Schmidt, Michael and Stichel, Thomas}, title = {Correlation Analysis of Different Building Parameters on the Part Properties of Parts Built by Simultaneous Laser Beam Melting of Polymers}, series = {Fraunhofer Direct Digital Manufacturing Conference DDMC 2016 : Conference Proceedings, March 2016, Berlin}, booktitle = {Fraunhofer Direct Digital Manufacturing Conference DDMC 2016 : Conference Proceedings, March 2016, Berlin}, publisher = {Fraunhofer Verlag}, abstract = {Simultaneous Laser Beam Melting of polymers (SLBM) allows the generation of multi-material components,consisting of different thermoplastic polymers, within one additive building process. Besides the common advantagesof conventional Laser Beam Melting (LBM), multi-material components built by SLBM can fulfill different productrequirements like different chemical resistances or haptic material properties within a single part. To achieve suchparts, different powder materials are deposited next to each other and preheated a few degrees below their meltingtemperatures by infrared emitters and laser radiation (λ = 10.60 μm), before in the last step the preheated powdersare molten simultaneously by an additional laser source (λ = 1.94 μm). In this paper, different polymer powders likepolypropylene (PP) and polyamide 12 (PA12) are used for the generation of multi-material specimens. By varyingdifferent building parameters according to a specified design of experiments, their influence on the part properties isanalyzed. Important building parameters are the intensity and the irradiation time of the laser beam used for meltingthe preheated powders. Besides using tensile tests to determine the tensile strength and the elongation at break, theaverage part height in dependence of the energy input is analyzed. The overall aim is to specify the correlationbetween different building parameters regarding the energy deposition on the resulting part properties.}, language = {en} } @article{LaumerStichelRathsetal., author = {Laumer, Tobias and Stichel, Thomas and Raths, Max and Schmidt, Michael}, title = {Analysis of the Influence of Different Flowability on Part Characteristics Regarding the Simultaneous Laser Beam Melting of Polymers}, series = {Physics Procedia}, volume = {83}, journal = {Physics Procedia}, publisher = {Elsevier}, issn = {1875-3892}, doi = {10.1016/j.phpro.2016.08.098}, pages = {937 -- 946}, abstract = {Powder based Additive Manufacturing technologies offer huge potential for building parts with almost no geometrical restrictions, but both the process controlling as well as the part properties are strongly dependent on different material characteristics of the material, like the flowability. In this work, different weight percentages of nano-scaled silica dioxide particles (Aerosil®) are admixed to pure polyethylene and polypropylene powder and the resulting flowability is determined. Besides using the Hausner ratio as standardized value, the degree of coverage is introduced as a new characteristic to quantify the powder flowability. The degrees of coverage are compared to the Hausner ratios to allow a discussion and evaluation about the different characteristic values. Additionally, tensile bars consisting of polypropylene are generated to determine the porosity by cross sections and the mechanical part properties by tensile testing. As mechanical part properties, the tensile strength and elongation at break are determined and the effects of different powder flowability on these properties are analyzed.}, language = {en} } @article{StichelFrickLaumeretal., author = {Stichel, Thomas and Frick, Thomas and Laumer, Tobias and Tenner, Felix and Hausotte, Tino and Merklein, Marion and Schmidt, Michael}, title = {A Round Robin study for selective laser sintering of polymers: Back tracing of the pore morphology to the process parameters}, series = {Journal of Materials Processing Technology}, volume = {252}, journal = {Journal of Materials Processing Technology}, number = {February}, publisher = {Elsevier}, doi = {10.1016/j.jmatprotec.2017.10.013}, pages = {537 -- 545}, abstract = {The mechanical properties of polymer parts built by Selective Laser Sintering are strongly related to the internal microstructure which differs with the applied production parameters. The paper focuses on the back tracing of the pore morphology of laser sintered polyamide-12 samples to the process parameters. Therefore, a data base is used which is supplied by a Round Robin initiative and includes mechanical tensile tests and the microstructural analysis of the pore morphology of several different sample charges built with different machines. The pore morphologies (porosity, pore density, pore shape and pore arrangement) measured by X-ray computed tomography are compared and discussed regarding the employed parameters and the resulting mechanical properties. The investigations point out that pore density is a superior indicator than porosity for mechanical issues. This is especially valid along the build direction since pore morphology has shown to be strongly anisotropic. Moreover, the analysis revealed that pore density is strongly affected by the process temperature, which is proved to be essential for the fabrication of mechanical robust parts using Selective Laser Sintering.}, language = {en} } @inproceedings{StichelAmendLaumeretal., author = {Stichel, Thomas and Amend, Philipp and Laumer, Tobias and Roth, Stephan}, title = {Multi-material deposition of polymer powders with vibrating nozzles inside laser beam melting machines}, series = {6th International Conference on Additive Technologies - iCAT 2016 : proceedings : N{\"u}rnberg, Germany, 29.-30. November 2016}, booktitle = {6th International Conference on Additive Technologies - iCAT 2016 : proceedings : N{\"u}rnberg, Germany, 29.-30. November 2016}, publisher = {Interesansa - zavod}, address = {Ljubljana}, abstract = {The generation of multi-material components using Laser beam melting (LBM) is a challenge which requires the invention of new coating devices for the preparation of arbitrary powder patterns. One solution is the usage of vibration-controlled nozzles for selective deposition of polymer powders. Powder flow can be initiated by vibration even when using powders with low flowability. In this report, the selective deposition of polymer powder by vibrating nozzles is investigated with respect to their application in LBM machines. Therefore, a steel nozzle attached to a piezo actor is applied, whereas the nozzle itself features internal channels which allow the precise control of the powder temperature using heat transfer oil. The setup is used to study the influence of temperature on the powder mass flow. The results show that, next to the vibration mode, the temperature strongly influences the powder mass flow which is done by affecting the moisture and thus the particle-particle adhesion forces. This shows that a precise control of the powder temperature inside the nozzle is required in order to achieve a constant mass flow and thus a successful application of vibrating nozzles inside LBM machines.}, language = {en} } @article{LaumerStichelNagulinetal., author = {Laumer, Tobias and Stichel, T. and Nagulin, K. and Schmidt, M.}, title = {Optical analysis of polymer powder materials for Selective Laser Sintering}, series = {Polymer Testing}, volume = {56}, journal = {Polymer Testing}, publisher = {Elsevier Science}, address = {Amsterdam [u.a.]}, issn = {1873-2348}, doi = {10.1016/j.polymertesting.2016.10.010}, pages = {207 -- 213}, abstract = {This study increases the basic understanding of optical material properties of polymer powders used in selective laser sintering (SLS). Therefore, different polymer powder materials were analyzed regarding their optical material properties with an integration spheres measurement setup. By the measurements a direct connection between the absorption behavior of the solid material and the overall optical material characteristics of the same material in powdery form could be shown. The results were used to develop an advanced explanation model for the optical material properties of powders. At present, existing explanation models only consider the occurring of multiple reflections in the gaps between the particles to explain the overall optical material properties of powder materials. Thus, by also considering the absorption behavior of the single particles, the basic understanding of the beam-matter interaction and their effect on the optical material properties of powder materials can be expanded.}, language = {en} } @inproceedings{LaumerSchmidtStichel, author = {Laumer, Tobias and Schmidt, Michael and Stichel, Thomas}, title = {Influence of temperature gradients on the part properties for the simultaneous laser beam melting of polymers}, series = {Proceedings of Laser in Manfacturing Conference 2015, June 22 - June 25, 2015 Munich, Germany}, booktitle = {Proceedings of Laser in Manfacturing Conference 2015, June 22 - June 25, 2015 Munich, Germany}, organization = {German Scientific Laser Society (WLT e.V.)}, abstract = {By Laser Beam Melting of polymers (LBM), parts with almost any geometry can be built directly out of CAD files without the need for additional tools. Thus, prototypes or parts in small series production can be generated within short times. Up to now, no multi-material parts have been built by LBM, which is a major limitation of the technology. To realize multi-material parts, new mechanisms for depositing different polymer powders as well as a new irradiation strategy are needed, by which polymers with different melting temperatures can be warmed to their specific preheating temperatures and be molten simultaneously. This is achieved by simultaneous laser beam melting (SLBM). In the process, two different materials are deposited next to each other and preheated a few degrees below their melting temperatures by infrared emitters and laser radiation (λ = 10.60 µm), before in the last step the two preheated powders are molten simultaneously by an additional laser (λ = 1.94 µm). So far, multi-material tensile bars have been realized and analyzed regarding their boundary zone between both materials. The experiments showed that the temperature gradients in the boundary zone and along the building direction seem to be of great importance for the process stability and the resulting part properties. Therefore, a detailed analysis of the occurring temperature gradients during the process is needed to identify adequate process adjustments regarding the temperature controlling. To analyze the temperature gradients, thermocouples positioned inside the powder bed are used. By varying the temperature of the building platform, the influence of different temperature gradients on the resulting part properties is shown.}, language = {en} } @inproceedings{Laumer, author = {Laumer, Tobias}, title = {The influence of micro-sized structures on the compound strength of multi-material components built by Simultaneous Laser Beam Melting of Polymers}, series = {Proceedings of LPM2016 - the 17th International Symposium on Laser Precision Microfabrication, 2016, Xian, China}, booktitle = {Proceedings of LPM2016 - the 17th International Symposium on Laser Precision Microfabrication, 2016, Xian, China}, abstract = {Simultaneous laser beam melting (SLBM) allows the direct realization of multi-material components consisting of different polymer materials by a single Additive Manufacturing (AM) process. To achieve a high compound strength between different materials by adhesive bonding, a common boundary zone based on diffusion of the macromolecules is necessary and thus, both materials needs to be compatible regarding their specific adhesion compatibility. However, by SLBM also incompatible polymers can be processed to multi-material parts. If two incompatible polymers are processed, a positive locking between the different materials is necessary to achieve a connection between the materials. The positive locking results of a random mixture process of the different powder materials during the powder deposition process by a two chamber recoater system, which leads to the forming of undercuts of one material in the other during the melting and recrystallization. In this paper, thermoplastic elastomer (TPE) and polypropylene (PP) powders, which are incompatible, are processed to multi-material specimens. By qualifying basic material properties, their influence on the process and especially on the forming of undercuts in the boundary zone is analyzed. To also allow the analysis of the influence of both material and process parameters on the resulting part properties, tensile test specimens are built and their tensile strength is determined. Additionally, cross sections of the boundary zone are prepared and analyzed by microscope images.}, language = {en} }