@inproceedings{MecklLubesederZausingeretal., author = {Meckl, D. and Lubeseder, Christian and Zausinger, C. and Wurmb, Ingo von and Meinhardt, Josef and Swidergal, Krzysztof and Wagner, Marcus}, title = {Simulation of press dies for large presses using the flexible multibody dynamics in Recurdyn}, series = {4th RecurDyn TechnologyDays 2014, M{\"u}nchen}, booktitle = {4th RecurDyn TechnologyDays 2014, M{\"u}nchen}, language = {en} } @article{SwidergalLubesederWurmbetal., author = {Swidergal, Krzysztof and Lubeseder, Christian and Wurmb, Ingo von and Lipp, Arnulf and Meinhardt, Josef and Wagner, Marcus and Marburg, Steffen}, title = {Experimental and numerical investigation of blankholder's vibration in a forming tool}, series = {Production Engineering - Research and Development}, volume = {9}, journal = {Production Engineering - Research and Development}, number = {5-6}, publisher = {Springer}, issn = {0944-6524}, doi = {10.1007/s11740-015-0640-9}, pages = {634}, abstract = {In order to achieve the energy and efficiency goals in modern automotive press shops, press systems with increasingly high stroke rates are being implemented (Meinhardt in proceedings of ACI forming in car body engineering. Bad Nauheim, Germany 2012). As a side effect, the structural dynamic loads on the press and especially on the forming tool increase. Hence, to design reliable and withstanding forming tools, a detailed knowledge of the vibrations and resulting critical loads is essential. In this paper, the main focus is put on the vibration of the blankholder—the heaviest moving component in the forming tool. To predict those vibrations, a coupled multibody-finite element simulation (MBS-FEM) is conducted, which combines rigid and elastic modeling approaches. Also, an experimental validation of the blankholder vibration under operational load is carried out. To compare the numerical and experimental results—both in time and frequency domain—an 1/3-octave analysis of a blankholder's vibrational speed is performed. The test measurements agree well with the MBS-FEM simulation.}, language = {en} } @inproceedings{SwidergalWagnerLubesederetal., author = {Swidergal, Krzysztof and Wagner, Marcus and Lubeseder, Christian and Wurmb, Ingo von and Meinhardt, Josef and Marburg, Steffen}, title = {Finite element simulation of blankholder's lift-off in a deep drawing tool using Abaqus/Standard}, series = {SIMULIA Community Conference, 19 - 21 May 2015, Berlin, Germany}, booktitle = {SIMULIA Community Conference, 19 - 21 May 2015, Berlin, Germany}, abstract = {In the deep drawing tools for forming car body parts, heavy blankholders are used to prevent buckling and wrinkling of the blank. During each press cycle, those large masses need to be lifted, raising thereby the structural dynamic load on the deep drawing tool and on the press. Therefore a detailed knowledge about the blankholder's lift-off event is essential for an accurate and robust design of forming tools. In this paper, a dynamic finite element method (FEM) simulation of a blankholder's lift-off in a selected automotive deep drawing tool is presented enabling identification of regions of critical stresses. The FEM model is built within the Abaqus/CAE environment and solved with Abaqus/Standard. Each dynamic analysis is preceded by a static analysis where the gravity load is applied and the lifting bolts are pre-stressed. A special emphasis is put on modeling the elastomer dampers, which are installed between lifting bolts and the blankholder to avoid hard impacts during the lift-off event. Those dampers are modelled using a hyperelastic material with hysteresis. In addition, an experimental validation of a blankholder's vibration under operating loading was carried out. The simulation results are in good agreement with the measurements.}, language = {en} } @inproceedings{SwidergalLubesederWurmbetal., author = {Swidergal, Krzysztof and Lubeseder, Christian and Wurmb, Ingo von and Meinhardt, Josef and Wagner, Marcus and Marburg, Steffen}, title = {Vibration analysis of an automotive forming tool using coupled MBS-FEM simulation and experimental validation}, series = {Proceedings of the 26th International Conference on Noise and Vibration Engineering (ISMA2014), Leuven, Belgium}, booktitle = {Proceedings of the 26th International Conference on Noise and Vibration Engineering (ISMA2014), Leuven, Belgium}, pages = {2931 -- 2942}, abstract = {To improve efficiency in automotive press shops, press systems with increasingly high stroke rates are beingimplemented, raising thereby the structural dynamic load on the press and especially on the forming tool. Adetailed knowledge of the vibrations and resulting critical loads is thus essential for accurate and reliable de-signs of forming tools. In this paper, multibody simulation (MBS) of a selected automotive tool is presentedenabling the identification of the vibration of its components. Starting from a pure rigid modelling approach,the MBS model is extended by adding finite element (FE) component to allow extra flexibility in the sys-tem. As an example, a detailed vibrational analysis - both in time and frequency domain - is performed ona blankholder. Also an experimental validation of a blankholder vibration under operational load is carriedout, with test signal data gained by piezoelectric accelerometers.}, language = {en} } @inproceedings{SwidergalLubesederWurmbetal., author = {Swidergal, Krzysztof and Lubeseder, Christian and Wurmb, Ingo von and Lipp, Arnulf and Meinhardt, Josef and Wagner, Marcus and Marburg, Steffen}, title = {Structural analysis of an automotive forming tool for large presses using LS-DYNA}, series = {10th European LS-DYNA Conference, W{\"u}rzburg}, booktitle = {10th European LS-DYNA Conference, W{\"u}rzburg}, language = {en} } @inproceedings{SwidergalLubesederWurmbetal., author = {Swidergal, Krzysztof and Lubeseder, Christian and Wurmb, Ingo von and Meinhardt, Josef and Wagner, Marcus and Marburg, Steffen}, title = {Effiziente Methode zur Bestimmung von dynamischen strukturellen Belastungen in Großpresswerkzeugen}, series = {36. EFB-Kolloquium Blechverarbeitung 2016, Fellbach}, booktitle = {36. EFB-Kolloquium Blechverarbeitung 2016, Fellbach}, language = {de} } @inproceedings{SwidergalThumannLubesederetal., author = {Swidergal, Krzysztof and Thumann, Philipp and Lubeseder, Christian and Wurmb, Ingo von and Meinhardt, Josef and Wagner, Marcus and Marburg, Steffen}, title = {Modeling and simulation of carbon black filled elastomer damper using LS-DYNA}, series = {LS-DYNA Forum 2014, Bamberg}, booktitle = {LS-DYNA Forum 2014, Bamberg}, language = {en} }