@inproceedings{JudenmannHoltmannspoetterEhrlich, author = {Judenmann, Anna and Holtmannsp{\"o}tter, Jens and Ehrlich, Ingo}, title = {Additive Manufacturing of Continuous Fiber-Reinforced Composites}, series = {Proceedings of the Munich Symposium on Lightweight Design 2022}, booktitle = {Proceedings of the Munich Symposium on Lightweight Design 2022}, language = {de} } @unpublished{SieglJungbauerGebhardtetal., author = {Siegl, Marco and Jungbauer, Bastian and Gebhardt, Jakob and Judenmann, Anna and Ehrlich, Ingo}, title = {Winding process of fibre-reinforced thermoplastic tubes with integrated tape production through in-situ roving impregnation and infrared consolidation}, series = {International Journal of Advanced Manufacturing Technology}, journal = {International Journal of Advanced Manufacturing Technology}, doi = {10.21203/rs.3.rs-4085105/v1}, abstract = {The present paper takes a novel approach to production of fibre-reinforced thermoplastic tubes. The method begins with the raw materials, reinforcing fibre and thermoplastic granulate which are processed to tapes through a newly developed direct impregnation process. It is followed by consolidation of fibre-reinforced thermoplastic tubes using infrared (IR) emitters in the filament winding process. This process employs various angles and utilizes a rotatable consolidation axis. The winding process operates at a constant speed, addressing the challenge of bending the fibre-reinforced tapes in the angle reversal areas near the tube ends. Experiments have confirmed that the process can run at speeds reaching approximately 470 mm/min. The design of the impregnation line takes into account the properties of the thermoplastic and the roving, allowing for a speed of up to 1 m/s.}, language = {en} } @article{SieglJungbauerGebhardtetal., author = {Siegl, Marco and Jungbauer, Bastian and Gebhardt, Jakob and Judenmann, Anna and Ehrlich, Ingo}, title = {Winding process of fibre-reinforced thermoplastic tubes with integrated tape production through in-situ roving impregnation and infrared consolidation}, series = {The International Journal of Advanced Manufacturing Technology}, volume = {135}, journal = {The International Journal of Advanced Manufacturing Technology}, number = {5-6}, editor = {Baeten, Somayeh}, publisher = {Springer Nature}, doi = {10.1007/s00170-024-14628-y}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-77827}, pages = {2847 -- 2870}, abstract = {This paper introduces a novel method for producing fibre-reinforced thermoplastic tubes by integrating tape production and consolidation into a single operation. This innovation diverges from conventional methods by combining processes to reduce costs by using raw materials instead of organotapes, allowing customised material combinations and utilising residual heat from tape production. The new process uses carbon roving and molten low-viscosity PA6 granulates, processed through a new direct impregnation setup in siphon design. Key advancements include a high-speed impregnation module capable of up to 1 m/s with high-performance extruders, cost-effective infrared emitters for winding, and a powered consolidation unit with adjustable winding angles between ±65° and ±90°. Experiments demonstrate operational speeds of approximately 471 mm/min, with an optimal cross-winding speed of 354 mm/min due to the technical limitations of the laboratory extruder and IR emitter used. Based on the technical limitations of the current system, future improvements and methodological changes will be discussed.}, language = {en} } @article{AndraeKastenmeierGebhardtetal., author = {Andrae, Matthias and Kastenmeier, Andreas and Gebhardt, Jakob and Ehrlich, Ingo and Gebbeken, Norbert}, title = {Shock-tube tests on conventional windows: Exploring retrofit concepts for enhanced blast protection}, series = {International Journal of Protective Structures}, journal = {International Journal of Protective Structures}, publisher = {SAGE}, issn = {2041-4196}, doi = {10.1177/20414196241284297}, abstract = {Ensuring blast protection for existing buildings, especially addressing the vulnerability of conventional windows, is a significant challenge. Such unprotected windows can shatter even with moderate blast loads, posing a substantial risk of injury to occupants. This article discusses experimental research on enhancing the blast protection of single casement windows with insulating glass units and frames made of unplasticized polyvinyl chloride (uPVC). A retrofit concept using anti-shatter films, metallic sash reinforcements, adhesive bonding of the glazing to the sash frame, and a burglary resistance fitting-system was developed and tested in an explosion-driven shock-tube. Moreover, novel patches made of glass fiber-reinforced polymer applied to the corners of the window frames have been tested and proven effective in providing additional strength to the window. The study concludes that the tested combination of retrofit measures can significantly reduce hazards from window fragments without compromising functionality or aesthetics.}, language = {en} } @inproceedings{RomanoHoinkesEhrlichetal., author = {Romano, Marco and Hoinkes, Carl J. J. and Ehrlich, Ingo and H{\"o}cherl, Johannes and Gebbeken, Norbert}, title = {Influence of the impactor on the experimentally determined energy dissipation properties of fiber-reinforced plastics with hybrid layups under high velocity impact loads}, series = {Proceeding of the 15th International Materials Symposium (IMSP´2014), Pamukkale University (Denizli, Turkey), 15./17. October 2014}, booktitle = {Proceeding of the 15th International Materials Symposium (IMSP´2014), Pamukkale University (Denizli, Turkey), 15./17. October 2014}, editor = {Meran, C.}, pages = {650 -- 664}, language = {en} } @inproceedings{HoinkesRomanoEhrlichetal., author = {Hoinkes, Carl J. J. and Romano, Marco and Ehrlich, Ingo and H{\"o}cherl, Johannes and Gebbeken, Norbert}, title = {Investigation of fibre reinforced plastics with monolithic and hybrid stacking sequences under high-velocity impact loads}, series = {Applied Research Conference 2014 - ARC 2014, 5th July 2014, Ingolstadt}, booktitle = {Applied Research Conference 2014 - ARC 2014, 5th July 2014, Ingolstadt}, editor = {Ziemann, Olaf and Mottok, J{\"u}rgen and Pforr, Johannes}, publisher = {Shaker}, address = {Aachen}, language = {en} } @inproceedings{EisenriedRomanoJungbaueretal., author = {Eisenried, Michael and Romano, Marco and Jungbauer, Bastian and Ehrlich, Ingo and Gebbeken, Norbert}, title = {Influence of parameters of the production process on the material quality of unidirectionally reinforced prepregs}, series = {Applied Research Conference 2013, ARC 2013 ; 17th and 18th October 2013, Deggendorf}, booktitle = {Applied Research Conference 2013, ARC 2013 ; 17th and 18th October 2013, Deggendorf}, editor = {Ziemann, Olaf and Bogner, Werner and Mottok, J{\"u}rgen}, publisher = {Shaker}, address = {Aachen}, pages = {70 -- 75}, language = {en} } @misc{BeimlerLeisslEbneretal., author = {Beimler, Josef and Leißl, Caroline and Ebner, Lena and Elsner, Michael and M{\"u}hlbauer, Gerhard and Kohlert, Dieter and Schubert, Martin J. W. and Weiß, Andreas P. and Sterner, Michael and Raith, Thomas and Afranseder, Martin and Krapf, Tobias and Mottok, J{\"u}rgen and Siemers, Christian and Großmann, Benjamin and H{\"o}cherl, Johannes and Schlegl, Thomas and Schneider, Ralph and Milaev, Johannes and Rampelt, Christina and Roduner, Christian and Glowa, Christoph and Bachl, Christoph and Schliekmann, Claus and Gnan, Alfons and Grill, Martin and Ruhland, Karl and Piehler, Thomas and Friers, Daniel and Wels, Harald and Pflug, Kenny and Kucera, Markus and Waas, Thomas and Schlachetzki, Felix and Boy, Sandra and Pemmerl, Josef and Leis, Alexander and Welsch, Andreas F.X. and Graf, Franz and Zenger, Gerhard and Volbert, Klaus and Waas, Thomas and Scherzinger, Stefanie and Klettke, Meike and St{\"o}rl, Uta and Heyl, C. and Boldenko, A. and Monkman, Gareth J. and Kujat, Richard and Briem, Ulrich and Hierl, Stefan and Talbot, Sebastian and Schmailzl, Anton and Ławrowski, Robert Damian and Prommesberger, Christian and Langer, Christoph and Dams, Florian and Schreiner, Rupert and Valentino, Piergiorgio and Romano, Marco and Ehrlich, Ingo and Furgiuele, Franco and Gebbeken, Norbert and Eisenried, Michael and Jungbauer, Bastian and Hutterer, Albert and Bauhuber, Michael and Mikrievskij, Andreas and Argauer, Monika and Hummel, Helmut and Lechner, Alfred and Liebetruth, Thomas and Schumm, Michael and Joseph, Saskia and Reschke, Michael and Soska, Alexander and Schroll-Decker, Irmgard and Putzer, Michael and Rasmussen, John and Dendorfer, Sebastian and Weber, Tim and Al-Munajjed, Amir Andreas and Verkerke, Gijsbertus Jacob and Renkawitz, Tobias and Haug, Sonja and Rudolph, Clarissa and Zeitler, Annika and Schaubeck, Simon and Steffens, Oliver and Rechenauer, Christian and Schulz-Brize, Thekla and Fleischmann, Florian and Kusterle, Wolfgang and Beer, Anne and Wagner, Bernd and Neidhart, Thomas}, title = {Forschungsbericht 2013}, editor = {Baier, Wolfgang}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg}, doi = {10.35096/othr/pub-799}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-7990}, pages = {80}, language = {de} } @misc{AppelhansKampmannMottoketal., author = {Appelhans, Marie-Luise and Kampmann, Matthias and Mottok, J{\"u}rgen and Riederer, Michael and Nagl, Klaus and Steffens, Oliver and D{\"u}nnweber, Jan and Wildgruber, Markus and Roth, Julius and Stadler, Timo and Palm, Christoph and Weiß, Martin Georg and Rochholz, Sandra and Bierl, Rudolf and Gschossmann, Andreas and Haug, Sonja and Schmidbauer, Simon and Koch, Anna and Westner, Markus and Bary, Benedikt von and Ellermeier, Andreas and V{\"o}gele, Daniel and Maiwald, Frederik and Hierl, Stefan and Schlamp, Matthias and Ehrlich, Ingo and Siegl, Marco and H{\"u}ntelmann, Sven and Wildfeuer, Matthias and Br{\"u}ckl, Oliver and Sterner, Michael and Hofrichter, Andreas and Eckert, Fabian and Bauer, Franz and Dawoud, Belal and Rabl, Hans-Peter and Gamisch, Bernd and Schmidt, Ottfried and Heberl, Michael and Thema, Martin and Mayer, Ulrike and Eller, Johannes and Sippenauer, Thomas and Adelt, Christian and Haslbeck, Matthias and Vogl, Bettina and Mauerer, Wolfgang and Ramsauer, Ralf and Lohmann, Daniel and Sax, Irmengard and Gabor, Thomas and Feld, Sebastian and Linnhoff-Popien, Claudia and Ławrowski, Robert Damian and Langer, Christoph and Schreiner, Rupert and Sellmair, Josef}, title = {Forschung 2019}, editor = {Baier, Wolfgang}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg}, isbn = {978-3-9818209-7-3}, doi = {10.35096/othr/pub-789}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-7890}, pages = {72}, abstract = {Bericht mit Forschungsprojekten aus verschiedenen Bereichen der OTH Regensburg mit dem Schwerpunktthema "K{\"u}nstliche Intelligenz" und einem Gespr{\"a}ch zur "Medizin der Zukunft"}, subject = {Forschung}, language = {de} } @inproceedings{LindnerBerndtTschurtschenthaletal., author = {Lindner, Matthias and Berndt, Dominik and Tschurtschenthal, Karl and Ehrlich, Ingo and Jungbauer, Bastian and Schreiner, Rupert and Pipa, Andrei V. and Hink, R{\"u}diger and Foest, R{\"u}diger and Brandenburg, Ronny and Neuwirth, Daniel and Karpen, Norbert and Bonaccurso, Elmar and Weichwald, Robert and Max, Alexander and Caspari, Ralf}, title = {Aircraft Icing Mitigation by DBD-based Micro Plasma Actuators}, series = {AIAA AVIATION 2020 FORUM: June 15-19, 2020}, booktitle = {AIAA AVIATION 2020 FORUM: June 15-19, 2020}, doi = {10.2514/6.2020-3243}, abstract = {We present the application of plasma actuators as a technology for ice prevention at airfoils. The miniaturized dielectric barrier discharge (DBD) plasma actuators (PA) were fabricated by means of microelectromechanical systems (MEMS). We elucidate how to make the actuator samples scalable and applicable to any desired shape by the use of flexible inorganic zirconia substrates. For this purpose, we applied our developed embedding method to integrate the micro actuators in modern carbon/glass fiber reinforced polymer (CFRP/GFRP) materials. Next, the embedded actuator samples were mounted on a mechanical air profile-like fixture and placed in the icing wind tunnel iCORE. The samples were tested in rime ice conditions at temperatures of -15 to -20° C and air speeds up to 30 m/s. Unlike other groups we used a thin film zirconia substrate as dielectric for the plasma actuator. Due to the low substrate thickness of just 150 µm, an operating voltage of 2 kVRMS is already sufficient enough for a stable plasma formation. The experiments show that the operated actuator was able to prevent the ice formation and first indications of a De-icing function were also found. Hence, we show that it is feasible to realize an anti-icing system with zirconia-based plasma actuators operated at lower voltages compared to conventional ones.}, language = {en} } @inproceedings{LindnerBerndtJungbaueretal., author = {Lindner, Matthias and Berndt, Dominik and Jungbauer, Bastian and Ehrlich, Ingo and Schreiner, Rupert and Pipa, Andrei V. and Hink, R{\"u}diger and Foest, R{\"u}diger and Brandenburg, Ronny and Max, Alexander and Caspari, Ralf}, title = {Fabrication, surface integration and testing of miniaturized dielectric barrier discharge plasma actuators for active flow control applications}, series = {AIAA Aviation 2019 Forum, 17-21 June 2019, Dallas, Texas}, booktitle = {AIAA Aviation 2019 Forum, 17-21 June 2019, Dallas, Texas}, doi = {10.2514/6.2019-2998}, language = {en} } @misc{WeberDendorferSuessetal., author = {Weber, Karsten and Dendorfer, Sebastian and S{\"u}ß, Franz and Kubowitsch, Simone and Schratzenstaller, Thomas and Haug, Sonja and Mohr, Christa and Kiesl, Hans and Drechsler, J{\"o}rg and Westner, Markus and Kobus, J{\"o}rn and Schubert, Martin J. W. and Zenger, Stefan and Pietsch, Alexander and Weiß, Josef and Hinterseer, Sebastian and Schieck, Roland and Scherzinger, Stefanie and Klettke, Meike and Ringlstetter, Andreas and St{\"o}rl, Uta and Bissyand{\´e}, Tegawend{\´e} F. and Seeburger, Achim and Schindler, Timo and Ramsauer, Ralf and Kiszka, Jan and K{\"o}lbl, Andreas and Lohmann, Daniel and Mauerer, Wolfgang and Maier, Johannes and Scorna, Ulrike and Palm, Christoph and Soska, Alexander and Mottok, J{\"u}rgen and Ellermeier, Andreas and V{\"o}gele, Daniel and Hierl, Stefan and Briem, Ulrich and Buschmann, Knut and Ehrlich, Ingo and Pongratz, Christian and Pielmeier, Benjamin and Tyroller, Quirin and Monkman, Gareth J. and Gut, Franz and Roth, Carina and Hausler, Peter and Bierl, Rudolf and Prommesberger, Christian and Ławrowski, Robert Damian and Langer, Christoph and Schreiner, Rupert and Huang, Yifeng and She, Juncong and Ottl, Andreas and Rieger, Walter and Kraml, Agnes and Poxleitner, Thomas and Hofer, Simon and Heisterkamp, Benjamin and Lerch, Maximilian and Sammer, Nike and Golde, Olivia and Wellnitz, Felix and Schmid, Sandra and Muntschick, Claudia and Kusterle, Wolfgang and Paric, Ivan and Br{\"u}ckl, Oliver and Haslbeck, Matthias and Schmidt, Ottfried and Schwanzer, Peter and Rabl, Hans-Peter and Sterner, Michael and Bauer, Franz and Steinmann, Sven and Eckert, Fabian and Hofrichter, Andreas}, title = {Forschungsbericht 2017}, editor = {Baier, Wolfgang}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg}, isbn = {978-3-9818209-3-5}, doi = {10.35096/othr/pub-1383}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-13835}, subject = {Forschung}, language = {de} } @inproceedings{NiedernhuberEhrlichHoltmannspoetter, author = {Niedernhuber, Michal and Ehrlich, Ingo and Holtmannsp{\"o}tter, Jens}, title = {Fiber-Oriented Repair of Fiber Reinforced Plastics: Investigations on Tensile Specimens}, series = {4th Applied Research Conference - ARC 2014, 5th July 2014, Ingolstadt}, booktitle = {4th Applied Research Conference - ARC 2014, 5th July 2014, Ingolstadt}, editor = {Ziemann, Olaf and Mottok, J{\"u}rgen and Pforr, Johannes}, publisher = {Shaker}, address = {Aachen}, pages = {298 -- 302}, language = {en} } @inproceedings{PongratzEhrlich, author = {Pongratz, Christian and Ehrlich, Ingo}, title = {Structural Dynamic Analysis of Thin Composite Plates Using Noncontact Measurement and Excitation}, series = {Applied Research Conference 2016 - ARC 2016, Augsburg, 24 June 2016}, booktitle = {Applied Research Conference 2016 - ARC 2016, Augsburg, 24 June 2016}, editor = {Mottok, J{\"u}rgen and Reichenberger, Marcus and Stolle, Reinhard}, publisher = {Pro Business Verlag}, address = {Berlin}, isbn = {978-3-86460-494-2}, pages = {351 -- 358}, language = {en} } @techreport{PongratzEhrlich, author = {Pongratz, Christian and Ehrlich, Ingo}, title = {DampSIM: Lebensdauer{\"u}berwachung von faserverst{\"a}rkten Kunststoffen auf Basis der strukurdynamischen Werkstoffd{\"a}mpfung}, series = {Forschungsbericht 2017 / Ostbayerische Technische Hochschule Regensburg}, journal = {Forschungsbericht 2017 / Ostbayerische Technische Hochschule Regensburg}, editor = {Baier, Wolfgang}, organization = {Ostbayerische Technische Hochschule Regensburg}, isbn = {978-3-9818209-3-5}, pages = {62 -- 63}, language = {de} } @techreport{PongratzEhrlich, author = {Pongratz, Christian and Ehrlich, Ingo}, title = {High-End-Strukturen f{\"u}r den Leichtbau - mit faserverst{\"a}rktem 3D-Druck}, series = {Forschung 2018 / Ostbayerische Technische Hochschule Regensburg}, journal = {Forschung 2018 / Ostbayerische Technische Hochschule Regensburg}, editor = {Baier, Wolfgang}, organization = {Ostbayerische Technische Hochschule Regensburg}, isbn = {978-3-9818209-4-2}, pages = {64 -- 65}, language = {de} } @misc{JudenmannPongratzEhrlichetal., author = {Judenmann, Anna and Pongratz, Christian and Ehrlich, Ingo and H{\"o}fer, Philipp and Holtmannsp{\"o}tter, Jens}, title = {Additive Fertigung von endlosfaserverst{\"a}rkten Kunststoffstrukturen}, series = {M{\"u}nchner Leichtbauseminar 2022, 26. October 2022, 16. November 2022, 30 November 2022, Munich/Neubiberg/Garching}, journal = {M{\"u}nchner Leichtbauseminar 2022, 26. October 2022, 16. November 2022, 30 November 2022, Munich/Neubiberg/Garching}, abstract = {Additive Fertigung hat sich in zahlreichen industriellen Anwendungen etabliert und bildet eine wichtige Schl{\"u}sseltechnologie. Im Gegensatz zu metallischen Werkstoffen, haben additiv gefertigte Bauteile aus Kunststoffen geringere Festigkeit und Steifigkeit, sodass sich ihre Verwendung als lasttragende Strukturen schwierig gestaltet. Insbesondere der Einsatz von endlosen Verst{\"a}rkungsfasern kann die mechanischen Eigenschaften additiv gefertigter Strukturen signifikant verbessern und die Fertigung hochbelastbarer Faserverbundstrukturen im 3D-Druckverfahren erm{\"o}glichen. Daher gilt es aktuell notwendige Anlagen und Prozessketten f{\"u}r den Fertigungsprozess aber auch Vorgehensweisen f{\"u}r die belastungsoptimierte Auslegung der Faserverl{\"a}ufe innerhalb des Bauteils zu entwickeln, um so das Themengebiet „Endlosfaserverst{\"a}rkter 3D-Druck" weiter voranzutreiben. F{\"u}r mehr r{\"a}umliche Freiheit bei der Positionierung der Druckbahnen k{\"o}nnen industrieroboterbasierte Systeme eingesetzt werden, um so das Potenzial gerichteter Bauweise von Faserverbundstrukturen auch im additiven Fertigungsprozess vollumf{\"a}nglich aussch{\"o}pfen zu k{\"o}nnen. Dabei erm{\"o}glicht ihr Einsatz auch eine r{\"a}umliche Ablage der Faserverst{\"a}rkung, wobei f{\"u}r die Materialablage ein geeigneter 3D-Druckkopf erforderlich ist. F{\"u}r die Implementierung der Faserverst{\"a}rkung ist zudem eine dem Lastfall entsprechende Auslegung des Bauteils sowie die Ermittlung einer sinnvollen Faserpositionierung innerhalb des Bauteils erforderlich, wobei unterschiedliche Variablen aus den Bereichen Material, Struktur und Fertigungsprozess ber{\"u}cksichtigt werden m{\"u}ssen. Im Rahmen des Vortrages werden die Herausforderungen der Technologieentwicklung des endlosfaserverst{\"a}rkten 3D-Drucks aufgegriffen sowie auf eine belastungsorientierte Faserpositionierung n{\"a}her eingegangen. Aktuelle Erkenntnisse werden diskutiert sowie eine Entwurfsmethodik f{\"u}r die Prozesspfadgenerierung vorgeschlagen.}, language = {de} } @misc{OlbrichPongratzBierletal., author = {Olbrich, Florian and Pongratz, Christian and Bierl, Rudolf and Ehrlich, Ingo}, title = {Method and System for Evaluating a Structural Integrity of an Aerial Vehicle}, series = {Europ{\"a}isches Patentblatt (09.12.2020) zur Anmeldung: OTH Regensburg, Anmeldenummer: 19179054.2, Patentnummer 1001/3748327, Ver{\"o}ffentlichungsnummer: 3 748 327}, journal = {Europ{\"a}isches Patentblatt (09.12.2020) zur Anmeldung: OTH Regensburg, Anmeldenummer: 19179054.2, Patentnummer 1001/3748327, Ver{\"o}ffentlichungsnummer: 3 748 327}, pages = {395 -- 396}, language = {en} } @article{NiedernhuberHoltmannspoetterEhrlich, author = {Niedernhuber, Michal and Holtmannsp{\"o}tter, Jens and Ehrlich, Ingo}, title = {Fiber-oriented repair geometries for composite materials}, series = {Composites, Part B}, volume = {94}, journal = {Composites, Part B}, doi = {10.1016/j.compositesb.2016.03.027}, pages = {327 -- 337}, abstract = {In this paper, the idea of fiber-oriented repair geometries for carbon fiber reinforced plastics (CFRP) is investigated. It considers the differing mechanical properties of unidirectional fiber reinforced material by excluding overlapping regions perpendicular to the fiber direction of the particular layer. A mechanical and numerical comparison of tensile strength of stepped joints with continuous step lengths per ply and stepped joints with reduced step lengths in plies with fiber orientation differing from load direction is performed. Finite element simulations show similar shear stresses. Mechanical tests of CFRP laminates with stepped joints show no significant deviation in tensile strength, in spite of a joint length reduction of nearly 40\%. This leads to the possibility of a significant reduction of repair area.}, language = {en} } @article{PongratzSchlampJungbaueretal., author = {Pongratz, Christian and Schlamp, Matthias and Jungbauer, Bastian and Ehrlich, Ingo and Petratos, P. and Mourtos, N.}, title = {Detection of Delamination Damages in Thin Composite Plates using Noncontact Measurement of Structural Dynamic Behavior}, series = {Athens Journal of Technology \& Engineering}, volume = {3}, journal = {Athens Journal of Technology \& Engineering}, number = {4}, doi = {10.30958/AJTE.3-4-3}, pages = {315 -- 331}, language = {en} } @misc{OlbrichPongratzBierletal., author = {Olbrich, Florian and Pongratz, Christian and Bierl, Rudolf and Ehrlich, Ingo}, title = {Method and System for Evaluating a Structural Integrity of an Aerial Vehicle}, language = {en} } @misc{BroserFalterŁawrowskietal., author = {Broser, Christian and Falter, Thomas and Ławrowski, Robert Damian and Altenbuchner, Amelie and V{\"o}gele, Daniel and Koss, Claus and Schlamp, Matthias and Dunnweber, Jan and Steffens, Oliver and Heckner, Markus and Jaritz, Sabine and Schiegl, Thomas and Corsten, Sabine and Lauer, Norina and Guertler, Katherine and Koenig, Eric and Haug, Sonja and Huber, Dominik and Birkenmaier, Clemens and Krenkel, Lars and Wagner, Thomas and Justus, Xenia and Saßmannshausen, Sean Patrick and Kleine, Nadine and Weber, Karsten and Braun, Carina N. and Giacoppo, Giuliano and Heinrich, Michael and Just, Tobias and Schreck, Thomas and Schnabl, Andreas and Gilmore, Amador T{\´e}ran and Roeslin, Samuel and Schmid, Sandra and Wellnitz, Felix and Malz, Sebastian and Maurial, Andreas and Hauser, Florian and Mottok, J{\"u}rgen and Klettke, Meike and Scherzinger, Stefanie and St{\"o}rl, Uta and Heckner, Markus and Bazo, Alexander and Wolff, Christian and Kopper, Andreas and Westner, Markus and Pongratz, Christian and Ehrlich, Ingo and Briem, Ulrich and Hederer, Sebastian and Wagner, Marcus and Schillinger, Moritz and G{\"o}rlach, Julien and Hierl, Stefan and Siegl, Marco and Langer, Christoph and Hausladen, Matthias and Schreiner, Rupert and Haslbeck, Matthias and Kreuzer, Reinhard and Br{\"u}ckl, Oliver and Dawoud, Belal and Rabl, Hans-Peter and Gamisch, Bernd and Schmidt, Ottfried and Heberl, Michael and G{\"a}nsbauer, Bianca and Bick, Werner and Ellermeier, Andreas and Monkman, Gareth J. and Prem, Nina and Sindersberger, Dirk and Tschurtschenthaler, Karl and Aurbach, Maximilian and Dendorfer, Sebastian and Betz, Michael A. and Szecsey, Tamara and Mauerer, Wolfgang and Murr, Florian}, title = {Forschung 2018}, editor = {Baier, Wolfgang}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg}, isbn = {978-3-9818209-5-9}, doi = {10.35096/othr/pub-1382}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-13826}, pages = {98}, subject = {Forschung}, language = {de} }