@article{SchelsEdlerHerdletal., author = {Schels, Andreas and Edler, Simon and Herdl, Florian and Hansch, Walter and Bachmann, Michael and Ritter, Daniela and Dudeck, Markus and Duesberg, Felix and Meyer, Manuel and Pahlke, Andreas and Hausladen, Matthias and Buchner, Philipp and Schreiner, Rupert}, title = {In situ quantitative field emission imaging using a low-cost CMOS imaging sensor}, series = {Journal of Vacuum Science \& Technology B}, volume = {40}, journal = {Journal of Vacuum Science \& Technology B}, number = {1}, publisher = {AIP Publishing}, doi = {10.1116/6.0001551}, abstract = {Spatially resolved field emission measurements represent an important factor in further development of existing field emitter concepts. In this work, we present a novel approach that allows quantitative analysis of individual emission spots from integral current-voltage measurements using a low-cost and commercially available CMOS camera. By combining different exposure times to extrapolate oversaturated and underexposed pixels, a near congruence of integral current and image brightness is shown. The extrapolation also allows parallel investigation of all individual tips participating in the total current with currents ranging from a few nanoampere to one microampere per tip. The sensitivity, which is determined by the integral brightness-to-current ratio, remains unchanged within the measurement accuracy even after ten full measurement cycles. Using a point detection algorithm, the proportional current load of each individual tip of the field emitter array is analyzed and compared at different times during the initial measurement cycle. Together with the extracted I-V curves of single emission spots from the integral measurement, the results indicate the effect of premature burnout of particularly sharp tips during conditioning of the emitter.}, language = {en} } @article{EdlerSchelsHerdletal., author = {Edler, Simon and Schels, Andreas and Herdl, Florian and Hansch, Walter and Bachmann, Michael and Dudeck, Markus and Duesberg, Felix and Pahlke, Andreas and Hausladen, Matthias and Buchner Philipp, and Schreiner, Rupert}, title = {Origin of the current saturation level of p-doped silicon field emitters}, series = {Journal of Vacuum Science \& Technology B}, volume = {40}, journal = {Journal of Vacuum Science \& Technology B}, number = {1}, publisher = {AIP Publishing}, doi = {10.1116/6.0001554}, abstract = {Using p-type semiconductors for field emitters is one simple way to realize an integrated current limiter to improve the lifetime of the cathode. In this work, the origin of the current saturation of p-type silicon emitters is investigated in detail. Single emitters are electrically characterized and compared to simulation results. With a simulation model considering a high surface generation rate and elevated tip temperature, a good agreement to the measured data is found. This observation is supported further by alteration of the surface experimentally. Electrical measurements after different treatments in hydrofluoric acid as well as heated and subsequent operation at room temperature are well explained by the influence of surface generation. Furthermore, it is shown that the field penetration leads to a small voltage drop and a strong geometry-dependent reduction of the field enhancement factor.}, language = {en} } @inproceedings{BuchnerKaiserHausladenetal., author = {Buchner, Philipp and Kaiser, Alexander and Hausladen, Matthias and Bartl, Mathias and Bachmann, Michael and Schreiner, Rupert}, title = {Silicon Nanowire Field Emitters with Integrated Extraction Gates Using Benzocyclobutene as an Insulator}, series = {37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic}, booktitle = {37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic}, publisher = {IEEE}, doi = {10.1109/IVNC63480.2024.10652314}, pages = {1 -- 2}, abstract = {We are continuously improving the performance of our field emission electron sources. In this work a geometrically optimized design of electron sources with silicon nanowire field emitters on pillars was fabricated. This new design increased the packing density of the emitters by using a hexagonal arrangement of the pillars and a pillar spacing of 40 µm. Benzocyclobutene was used as the insulator material for an integrated (Cr/Ni) extraction gate. A modified fabrication process for the field emitters further improved reproducibility and reliability. An emission current of about 0.4 mA was measured for 30 minutes at an extraction voltage of 250 V and an anode voltage of 500 V. Electron transmission through the gate reached almost 100\%.}, language = {en} } @inproceedings{HausladenBomkeBuchneretal., author = {Hausladen, Matthias and Bomke, Vitali and Buchner, Philipp and Bachmann, Michael and Knapek, Alexandr and Schreiner, Rupert}, title = {Influence of Geometrical Arrangements of Si Tip Arrays Fabricated by Laser Micromachining on their Emission Behaviour}, series = {2021 34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France}, booktitle = {2021 34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France}, publisher = {IEEE}, address = {Piscataway, N.J.}, isbn = {978-1-6654-2589-6}, issn = {2380-6311}, doi = {10.1109/IVNC52431.2021.9600717}, abstract = {ensely packed emitters on a field emission array lead typically to mutual shielding. Taking biology as a role model for geometric arrangements could be a way to reduce this effect. For comparison, two electron sources, one with a spiral and a second with conventional rectangular (orthogonal) arranged emitters, were fabricated and investigated. Emission currents of 6 µA in the spiral ordered array and 120 µA in the rectangular array were reached with an extraction voltage of 400 V. From a mid-term measurement over 1 h a current stability of ±8.8 \% (spiral) respectively ±5.7 \% (rectangular) with a mean degradation of -3.0 µA/h (spiral) and -0.12 µA/h (rectangular) could be observed.}, language = {en} } @inproceedings{BuchnerBomkeHausladenetal., author = {Buchner, Philipp and Bomke, Vitali and Hausladen, Matthias and Edler, Simon and Bachmann, Michael and Schreiner, Rupert}, title = {Investigation on the Emission Behaviour of p-doped Silicon Field Emission Arrays with Individually Controllable Single Tips}, series = {2021 34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France}, booktitle = {2021 34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France}, publisher = {IEEE}, isbn = {978-1-6654-2589-6}, doi = {10.1109/IVNC52431.2021.9600756}, pages = {1 -- 2}, abstract = {Four individually controllable emission tips consisting of <111> p-Type silicon, were structured on a glass substrate by laser ablation. A matching extraction grid was manufactured in the same manner and aligned with the emitters. The resulting samples were characterized in ultra-high vacuum. As expected, the individual currents show a strong saturation and in the saturation region a considerably lower current fluctuation than n-type silicon due to charge carrier depletion. The individual tips behave completely independent behaviour from each other and the overall emission can be deduced from the sum of the currents through the individual tips.}, language = {en} } @inproceedings{BartlBuchnerHausladenetal., author = {Bartl, Mathias and Buchner, Philipp and Hausladen, Matthias and Asgharzadehkhorasani, Ali and Bachmann, Michael and Schreiner, Rupert}, title = {Simulations and Investigations of Silicon Nanowire Field Emitters}, series = {37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic}, booktitle = {37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic}, publisher = {IEEE}, doi = {10.1109/IVNC63480.2024.10652355}, pages = {1 -- 2}, abstract = {The emission behavior of field emission electron sources consisting of a silicon nanowire cathode, an extraction grid electrode and a planar anode was investigated based on a particle tracing simulation using FEM. The focus was on the influence of the grid geometry as well as the positioning of the grid relative to the emitters on the electron transmission. The highest transmission can be achieved with the emitter tips protruding 10 µm trough the extraction grid openings. The transmission decreases more rapidly with increasing distance between the tip and the grid the thicker the grid is.}, language = {en} } @article{HausladenBuchnerBartletal., author = {Hausladen, Matthias and Buchner, Philipp and Bartl, Mathias and Bachmann, Michael and Schreiner, Rupert}, title = {Integrated multichip field emission electron source fabricated by laser-micromachining and MEMS technology}, series = {Journal of Vacuum Science \& Technology B}, volume = {42}, journal = {Journal of Vacuum Science \& Technology B}, number = {1}, publisher = {AIP Publishing}, doi = {10.1116/6.0003233}, abstract = {In this work, high-current field emission electron source chips were fabricated using laser-micromachining and MEMS technology. The resulting chips were combined with commercially available printed circuit boards (PCBs) to obtain a multichip electron source. By controlling the separate electron sources using an external current control circuit, we were able to divide the desired total current evenly across the individual chips deployed in the PCB-carrier. In consequence, we were able to show a decreased degradation due to the reduced current load per chip. First, a single electron source chip was measured without current regulation. A steady-state emission current of 1 mA with a high stability of ±1.3\% at an extraction voltage of 250 V was observed. At this current level, a mean degradation slope of -0.7 μA/min with a nearly perfect transmission ratio of 99\% ± 0.4\% was determined. The measurements of a fully assembled multichip PCB-carrier electron source, using a current control circuit for regulation, showed that an even distribution of the desired total current led to a decreased degradation. This was determined by the increase in the required extraction voltage over time. For this purpose, two current levels were applied to the electron source chips of the PCB-carrier using an external current control circuit. First, 300 μA total current was evenly distributed among the individual electron source chips followed by the emission of 300 μA per electron source chip. This allows the observation of the influence of a distributed and nondistributed total current, carried by the electron source chips. Thereby, we obtained an increase in the mean degradation slope from +0.011 V/min (300 μA distributed) to +0.239 V/min (300 μA per chip), which is approximately 21 times higher. Moreover, our current control circuit improved the current stability to under 0.1\% for both current levels, 300 μA distributed and 300 μA per chip.}, language = {en} } @inproceedings{SchelsHerdlHausladenetal., author = {Schels, Andreas and Herdl, Florian and Hausladen, Matthias and Wohlfartsst{\"a}tter, Dominik and Bachmann, Michael and Edler, Simon and D{\"u}sberg, Felix and Pahlke, Andreas and Buchner, Philipp and Schreiner, Rupert and Hansch, Walter}, title = {Beta Factor Mapping of Individual Emitting Tips During Integral Operation of Field Emission Arrays}, series = {2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA}, booktitle = {2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA}, publisher = {IEEE}, isbn = {979-8-3503-0143-4}, doi = {10.1109/IVNC57695.2023.10188957}, pages = {224 -- 226}, abstract = {Emission uniformity mappings of field emitter arrays provide important insight into degradation mechanisms, but are often laborious, non-integral, costly, or not quantifiable. Here, a low-cost Raspberry Pi HQ camera is used as an extraction anode to quantify the emission distribution in field emitter arrays. A verification measurement using controlled SEM electron beams proves, that current-voltage characteristics of individual emission sites can be determined by combining the integral electrical data with the image data. The characteristics are used to quantify the field enhancement factors of an 30x30 silicon field emitter array during integral operation. Comparison of the field enhancement factor distributions before and after a one-hour constant current operation at 1 µA shows an increase from 50 actively emitting tips before to 156 after the measurement. It is shown, that the distribution of field enhancement factors shifts towards lower values, due to the increasing degradation for high field enhancement tips, especially above 1500.}, language = {en} } @inproceedings{HausladenBuchnerSchelsetal., author = {Hausladen, Matthias and Buchner, Philipp and Schels, Andreas and Edler, Simon and Bachmann, Michael and Schreiner, Rupert}, title = {An Integrated Field Emission Electron Source on a Chip Fabricated by Laser-Micromachining and Mems Technology}, series = {2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA}, booktitle = {2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA}, publisher = {IEEE}, isbn = {979-8-3503-0143-4}, doi = {10.1109/IVNC57695.2023.10189001}, pages = {115 -- 116}, abstract = {A silicon field emission electron source consisting of a cathode and a grid electrode has been fabricated by laser micromachining. The cathode features 21×21 tips on an area of 4×4 mm 2 , With a self-aligning MEMS technology for the aperture grid, a high electron transmission (99 \%) was achieved. Onset voltages of 50…70 V were observed for an emission current of 1 nA. A stable emission current of 1 mA ± 1.3 \% at an extraction voltage of 250 V was observed during a 30-min operation.}, language = {en} } @inproceedings{BuchnerHausladenSchelsetal., author = {Buchner, Philipp and Hausladen, Matthias and Schels, Andreas and Herdl, Florian and Edler, Simon and Bachmann, Michael and Schreiner, Rupert}, title = {An Integrated Silicon Nanowire Field Emission Electron Source on a Chip with High Electron Transmission}, series = {2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA}, booktitle = {2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA}, publisher = {IEEE}, isbn = {979-8-3503-0143-4}, doi = {10.1109/IVNC57695.2023.10188878}, pages = {6 -- 8}, abstract = {Silicon nanowire field emission arrays (50 × 50 pillars) were fabricated on a silicon glass hybrid wafer. The glass acts both as the support for the whole structure and insulator between cathode and extraction grid. The extraction grid matches the emitter structures and is optically aligned and adhered to the emitter chip by a vacuum compatible epoxide adhesive. These chips exhibit an emission current of about 600 μA at an extraction voltage of 300 V. The electron transmission through the grid is above 80 \%. 58-hour longtime measurements were conducted showing low degradation of the emission current and high stability of electron transmission.}, language = {en} } @inproceedings{HausladenSchelsBuchneretal., author = {Hausladen, Matthias and Schels, Andreas and Buchner, Philipp and Bartl, Mathias and Asgharzade, Ali and Edler, Simon and Wohlfartsst{\"a}tter, Dominik and Bachmann, Michael and Schreiner, Rupert}, title = {Improved Method for Determining the Distribution of FEA Currents by Optical CMOS Sensors}, series = {37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic}, booktitle = {37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic}, publisher = {IEEE}, doi = {10.1109/IVNC63480.2024.10652543}, pages = {1 -- 2}, abstract = {CMOS image sensors are utilized to determine the time- and spatially-resolved distribution of the electron emission of silicon field emission arrays. During initial experiments, rather low field emission currents already visibly damaged the sensor surface, altering the system accuracy over the measurement time. Therefore, we coated the sensor surface with copper for protection. In contrast to the original insulating surface, the Cu coating provides a conductive surface for incident electrons and improves heat dissipation in addition. This prevents localized surface charges and surface damages which stabilize the system accuracy.}, language = {en} } @article{BachmannDuesbergPahlkeetal., author = {Bachmann, Michael and D{\"u}sberg, Felix and Pahlke, Andreas and Edler, Simon and Schels, Andreas and Herdl, Florian and Hausladen, Matthias and Buchner, Philipp and Schreiner, Rupert}, title = {The "LED-version" of the electron gun: An electron source for operation in ambient pressure environments based on silicon field emitter arrays}, series = {Vakuum in Forschung und Praxis}, volume = {35}, journal = {Vakuum in Forschung und Praxis}, number = {3}, publisher = {Wiley}, doi = {10.1002/vipr.202300801}, pages = {32 -- 37}, abstract = {We report on our progress to develop and optimize electron sources for practical applications. A simple fabrication process is introduced based on a wafer dicing saw and a wet chemical etch step without the need for a clean room. Due to the formation of crystal facets the samples show a homogeneous geometry throughout the array. Characterization techniques are developed to systematically compare various arrays. A very defined measurement procedure based on current controlled IV-sweeps as well as lifetime measurements at various currents is proposed. To investigate the current distribution in the array a commercial CMOS detector is used and shows the potential for in depth analysis of the arrays. Finally, a compact hermetically sealed housing is presented enabling electron generation in atmospheric pressure environments.}, language = {en} }