Refine
Document Type
Reviewed
- Begutachtet/Reviewed (12)
Keywords
- Flexible Electronics (3)
- Hybrid Electronics (3)
- Interconnection technology (3)
- Soldering (3)
- Printed Electronics (2)
- Aufbau- und Verbindungstechnik (1)
- Elektronikproduktion (1)
- Elektronische Baugruppen (1)
- Leiterplatten (1)
- printed electronics, strain gauge, 3D substrate, aerosol jet, piezo jet, dielectric, silver nanoparticle ink, carbon paste, pressure sensor (1)
Institute
In this work, on different substrate materials thermally cured polymer thick-film (PTF) pastes are connected to surface mount technology resistors using a SnBiAg solder alloy. The effect of substrate pre-treatment with atmospheric plasma and thermal cycling on the shear strength of these interconnections is investigated, and the shear forces obtained are graded using United States Defense Standard / Military Standard (MIL-STD) 883. In particular, the build-up of solder interconnections on conductive structures made of commercially available copper-containing PTF pastes and their mechanical characterization is novel. As well as the mechanical characterization of conductive structures, made of PTF pastes, on plasma-treated substrates and their grading using the MIL-STD 883. In addition, interconnections with silver-containing conductive structures are realized for comparison. Depending on the interconnection system, component mean shear forces of up to 31 N are achieved. While some systems meet the 1.25× criterion of MIL-STD 883, the majority of the systems investigated do not meet the 1.00× criterion. Hereby, the adhesion between the conductive structure and the substrate usually fails. Plasma pre-treatment shows an adhesion-increasing effect only for a proportion of substrate materials used, as does thermal aging. But thermal loads can also impair the adhesive strength.
Characterization of Crimp Interconnections for Hybrid Integration of Screen-Printed Electronics
(2021)
In this work, electrical contacts between piercing-crimp terminals and screen-printed silver structures on three different polymeric films are characterized electrically and mechanically before and after accelerated thermal aging tests. Temperature cycling and constant thermal load tests were performed as like as ampacity and resistance measurements and tensile tests. The tensile tests show that the mechanical strength of the crimp connection depends on substrate material, but is independent of the aging state. For all joints, breaking forces of more than 100 N were achieved. Furthermore, some of tested connections can be loaded with more than 2.5 A in unaged state till they heat up by 25 K. Besides that, accelerated thermal aging generally leads to a reduction in electrical resistance in our experiments.
Evaluation of detatchable board-to-board interconnects on screen printed electronic structures
(2021)
Hybrid printed electronics (HPE) combines advantages of conventional electronics manufacturing technologies such as surface mount technology with those of printed electronics in order to realize more complex electronic systems. To realize the final product, such HPE subassemblies have to be connected to higher-level assemblies. So far interconnection techniques for the so-called level 3 interconnection between printed subsystems and standard electronics have not yet been considered adequately in scientific research. In this paper, alternative detachable level 3 interconnection technologies, i.e. spring loaded contact pins, zero insertion force (ZIF) as well as Non-ZIF connectors are investigated systematically regarding their electrical behaviour against the background of printed electronics. Screen-printed silver filled polymer thick film paste is used to realize printed conductor patterns on flexible polymer substrates, which are connected later on with the alternatives mentioned above. Transition resistance is measured using the four wire method as produced, after repeated mating cycles as well as after accelerated aging tests. The various electrical contacts are subjected to thermal stress in temperature cycling testing and during aging at a constant high temperature. As a result it can be stated, that the sping-loaded contact pins used in this investigation show superior behavior compared with the selected connectors in terms of resistance increase after mating cycles. Concerning long-term behavior after thermal cyling and high temperature storage, all investigated alternaives reveal convincing results.
In this paper the stress on electronic components for Conformable Electronic applications is evaluated. During High-Pressure-Forming (HPF) and subsequent overmolding (OM) these components have to withstand high amounts of stress. Globtops are used to protect 0402 as well as 0603-sized components mounted on different polymer substrates. The components are placed in different areas of deformation (for HPF) and melt velocities (for OM). The components are afterwards examined by means of electrical resistance measurements and shear force measurements as well as micro-sections. For conductive adhesive, the globtop material positively influenced the resistance change after deformation, soldered assemblies showcased good formability up to 20 %. The shear force drop caused by higher deformations could be mitigated using globtop materials. Soldered components were able to withstand OM when globtops were used. Here, smaller components seem to take less damage from the impacting melt. Components should be placed in areas where the melt has cooled down to prevent damages.
The integration of SMT components is necessary to produce more complex assemblies within the framework of conformable electronics. During High-Pressure-Forming (HPF) and subsequent overmolding electronic components must withstand high amounts of stress. In this study 0402- as well as 0603-sized chip resistors were mounted on different common polymer substrates using conductive adhesive paste followed by electrical and mechanical evaluation. Prior to HPF electronic components were positioned in areas of different local deformation. After HPF the specimen were characterized by shear force testing and electrical resistance measurements. In a similar manner, electronic components were tested to assess the mechanical behavior during injection molding. To examine different melt induced stress scenarios, electronic components were arranged parallel as well as perpendicular to the flow direction of the melt at different positions. Additionally, three different injection speeds were evaluated to assess the influence on the electrical conductivity and functionality of the assemblies. It was found that meandering of conductors is necessary for higher deformations. El. components (without additional nonconductive adhesives) can be placed in areas of up to 15% deformation, smaller package sizes seem to be advantageous for HPF. Regarding overmoulding, it was found that larger components (larger bonding area) is beneficial. Also, placement near the injection point, as well as low injection speeds should be avoided. Overall, el. components should be protected (using globtops / underfills etc.) to withstand consecutive HPF and overmoulding.
In the research project AVerdi the influence of photonic sintering methods on the resulting electrical conductivity, sintering duration and adhesion of digitally printed silver nanoparticle inks was investigated and compared to convective sintering. Conductor paths with film thicknesses below 1 μm were applied on flexible polymer substrates via inkjet printing. Aerosoljet printing was used to generate thicker lines up to 11 μm on injection molded substrates. Photonic sintering was carried out with near infrared emitters or ultraviolet light emitting diodes. For inkjet printed structures on polyimide a conductivity up to 24 % relative to bulk silver was achieved after a sintering duration of 2 s and 5 s for the near infrared and the ultraviolet light source, respectively. Oven sintered samples showed an electrical conductivity of 14 % after 1 h at 200° C. On polyethylene terephthalate a conductivity around 7 % was achieved after irradiation with near infrared light for 1 s, whereas convectively sintered samples showed a conductivity around 4 %. All material combinations sintered by the different methods showed good adhesion. The overall results of long-term behavior after thermal-cycling, regarding electrical conductivity and adhesion, show that the photonically sintered structures achieve similar results compared to the reference. The photonically sintered structures generated with the aerosoljet on polyamide 6 achieved conductivity values up to 19 %, which were comparable to the furnace sintered reference samples. On liquid crystal polymer substrates conductivity values reached up to 35 % after sintering with ultraviolet light emitting diodes for 60 s. Oven sintered samples showed a conductivity around 25 % after 1 h at 150° C. The adhesion of the silver nanoparticle ink on liquid crystal polymer and polyamide 6 substrates is better than with the reference samples. The reliability tests show fewer failures with alternative sintered samples. In this study only the results for inkjet printed structures are presented.
Strain sensors based on the resistive principle have been developed and produced by inkjet printing. Depending on the surface conditions of the substrates and the properties of the silver inks, with adequate densification of the printed nanoparticle containing structures, gauge factors of around 2.6, dimensions of 6.7 mm × 6.4 mm and grid line widths of around 90 μm, have been achieved with silver inks. Performance tests including up to 120 mechanical deformation cycles have been successfully carried out.
Use of Printed Sensors to Measure Strain in Rolling Bearings under Isolated Boundary Conditions
(2023)
The knowledge of the operating conditions in rolling bearings in technical applications offers many advantages, for example, to ensure a safe operation and to save resources and costs with the help of condition monitoring and predictive maintenance procedures. In many cases, it is difficult to implement sensors to measure the operating conditions of the rolling bearing, for reasons such as inaccessibility of the mounting position or non-compliance with installation space neutrality, which influences the sensor on the measuring point. Printed sensors using a digital deposition process, which can be used in very narrow design spaces, offer advantages in this respect. So far, these sensors have not been established in rolling bearings, so there is potential for technical application. This paper discusses the fundamental advantages and disadvantages as well as the challenges of the application, and it demonstrates the feasibility under isolated boundary conditions by applying a printed strain gauge sensor to the outer ring of a cylindrical roller bearing NU210 in an experimental setup to measure the strain under load. In this setup, the outer ring is deformed by 2 mm under an increasing radial load using a hydraulic press, and the strain is measured. Both a commercial reference sensor and a FE-simulation are used to validate the measurement. The results show that an implementation using printed sensors as a strain gauge works successfully. The resulting challenges, such as measuring strain gradients and printing on curved surfaces, are finally evaluated, and an outlook for further work is given.
Strain sensors based on the resistive principle have been developed and produced by inkjet printing of nanostructured materials. Miniaturized sensor structures with grid line widths of around 75 µm and overall dimensions of 6.7 mm × 6.4 mm were successfully realized on Polyimid foils. The influence of the surface properties and the silver nanoparticle ink on the printed strain gauges was examined. With adequate densification of the printed nanoparticle containing structures, gauge factors of around 3.9 or higher were achieved. Results of reliability tests under environmental stress showed the need for a protective coatings to ensure stable long-term behavior. With adequate coatings, stable sensors are possible under a wide range of environmental conditions, such as high temperature storage or thermal cycling.
Reflow soldering of printed flexible low-cost electronics continues to pose a challenge, which is hampering the growth of the technology. The specific process parameter requirements severely limit the available soldering technologies. This study focuses on the suitability of a new photonic soldering process based on individually controllable near-infrared light emitting diodes (NIR LEDs) for processing screen-printed silver (Ag) structures and etched copper (Cu) structures on polyethylene terephthalate (PET) with low-temperature solders of the Tin-Bismuth-Silver (SnBiAg) group. The approach enabled various component sizes to be successfully soldered under more favorable conditions. An analysis of the shear strength shows comparable behavior for the copper structures compared to samples that were convectively soldered. A significant improvement in the shear strength of the printed silver structures was achieved using the new NIR process.