TY - JOUR A1 - Werner, Ulrich ED - werner, ulrich T1 - Vibration control of large induction motors using actuators between motor feet and steel frame foundation JF - Mechanical Systems and Signal Processing N2 - In the paper a theoretical analysis is deduced regarding vibration control of large induction motors – power rating >=1 MW – with roller bearings, using actuators between motor feet and a soft steel frame foundation. Based on a multibody model, the mathematical coherences are shown, including the feedback control system. Afterwards a numerical example of a soft mounted, converter driven, 2-pole induction motor (1.6 MW) with ball bearings is presented, where the bearing housing vibrations and the foundation vibrations are analyzed with and without control system. It could be shown, that without vibration control system the operating speed range cannot be used completely because of resonances, caused by the soft foundation. Therefore, critical speed areas occur, where steady state operation is not possible. However, with the vibration control system, the whole operating speed range can be used. The aim of the paper is to show the capability of using a vibration control system with actuators between motor feet and a soft foundation, for avoiding off-limits areas for the operation speed of large induction motors. KW - Induction motors KW - Active vibration control KW - Actuators KW - Steel frame foundation Y1 - 2018 U6 - https://doi.org/10.1016/j.ymssp.2018.04.033 VL - 112 PB - Elsevier ER - TY - CHAP A1 - Wachter, Raimund A1 - Werner, Ulrich A1 - Herzog, Hans-Georg A1 - Bauer, Christian ED - Wachter, Raimund ED - Werner, Ulrich ED - Herzog, Hans-Georg ED - Bauer, Christian T1 - Vibration behaviour of a 11 kW two pole induction motor mounted on elastic steel frame foundation with actuator system BT - Proceedings of the 12th Virtual Conference on Vibrations in Rotating Machinery (VIRM), 14-15 October 2020 T2 - 12th International Conference on Vibrations in Rotating Machinery N2 - This paper describes the vibration behaviour of a small (11 kW) two pole induction motor, which is mounted on an elastic steel frame foundation with a special actuator system. This paper presents natural frequencies as a result of experimental model analysis of the whole system – motor, actuator system and steel frame foundation – and compares them to the numerical modal analyses using a finite element model. Additionally, forced vibrations are measured using the actuators as a shaker to de­ rive the resonance frequencies of the system. The measured natural frequencies by modal analysis, the measured resonance frequencies and the simulated natural fre­ quencies are compared to each other. Additionally, the necessary electrical power of the electrodynamic actuators is analysed. KW - Induction motors KW - Actuator system KW - Vibration analysis Y1 - 2020 UR - https://www.taylorfrancis.com/chapters/oa-edit/10.1201/9781003132639-27 SN - 9781003132639 PB - CRC Press ER - TY - CHAP A1 - Werner, Ulrich ED - Werner, Ulrich T1 - Influence of electromagnetic field damping on the vibration stability of soft mounted induction motors with sleeve bearings, based on a multibody model T2 - Technische Mechanik - European Journal of Engineering Mechanics : Special Issue for the 12th International Conference on Vibrations in Rotating Machines (SRIM 2017) N2 - The paper shows an analytical vibration model for stability analysis of soft mounted induction motors with sleeve bearings, especially focusing on the influence of electromagnetic field damping on the limit of vibration stability. The model is a multibody model, considering the electromagnetic influence – including the electromagnetic field damping effect –, stiffness and internal material damping of the rotor structure, stiffness and damping of the bearing housings and end shields, stiffness and damping of the foundation elements and stiffness and damping of the oil film of the sleeve bearings. The aim of the paper is to unite all these influences in a model and to derive a procedure for calculating the limit of vibration stability, with considering the electromagnetic field damping effect. Additionally, a numerical example is presented, where the influence of electromagnetic field damping on the limit of vibration stability is shown, as well as the influence of the foundation elements and of the internal damping of the rotor. The procedure and conclusions can also be adopted into finite-element analysis. KW - Induction motors KW - Multibody model KW - Stability analysis KW - Electromagnetic field damping KW - Soft mounted Y1 - 2017 U6 - https://doi.org/10.24352/UB.OVGU-2017-100 VL - 37 IS - 2/5 ER - TY - CHAP A1 - Werner, Ulrich ED - Werner, Ulrich T1 - Increasing the threshold of vibration stability of soft mounted induction motors with elastic rotors and sleeve bearings using active motor foot mounts T2 - Proceedings of ISMA2018 including USD2018 N2 - In the paper, the threshold of vibration stability of induction motors with flexible shafts and sleeve bearings, mounted on soft steel frame foundations with active motor foot mounts, is analyzed. The developed model is based on a multibody model, considering electromagnetic influence, stiffness and internal damping of the rotor, stiffness and damping of the bearing housings and end shields, stiffness and damping of the foundation and stiffness and damping of the oil film of the sleeve bearings. Additionally the stiffness and damping of the motor foot mounts – which are positioned between the motor feet the soft steel frame foundation – are considered, as well as the controlled forces which are applied in the vibration system by the motor foot mounts, using PD-controllers. The aim of the paper is to unite all these influences in a mathematical model and to derive a procedure for calculating the threshold of vibration stability. Based on a numerical example it can be shown, that the threshold of stability can be pushed to very high rotor speeds, using active motor foot mounts. KW - Induction motors KW - Active vibration control KW - Threshold of stability KW - Sleeve bearings KW - Motor foot mounts Y1 - 2018 UR - https://past.isma-isaac.be/downloads/isma2018/proceedings/Proceedings_ISMA-USD2018.pdf ER - TY - CHAP A1 - Werner, Ulrich ED - Werner, Ulrich T1 - Influence of dynamic magnetic eccentricity on sleeve bearing housing vibrations of induction motors considering electromagnetic field damping N2 - The paper shows the influence of dynamic magnetic eccentricity on the sleeve bearing housing vibrations of induction motors, considering electromagnetic field damping. The analytical model contains electromagnetic forces in respect of electromagnetic field damping, stiffness and internal (rotating) damping of the rotor, dynamic magnetic eccentricity, stiffness and damping of the support, and stiffness and damping of the oil film of the sleeve bearings. Based on an analytical rotordynamic model, a practicable method is presented, showing how to consider electromagnetic field damping, when analyzing forced vibrations caused by dynamic magnetic eccentricity, which can also be adopted in a Finite-Element-Analysis. KW - Induction motors KW - Dynamic magnetic eccentricity KW - Electromagnetic field damping KW - Sleeve bearings KW - Bearing housing vibrations Y1 - 2017 UR - https://www.researchgate.net/publication/318307655 ER - TY - CHAP A1 - Werner, Ulrich ED - werner, ulrich T1 - Calculation procedure to derive the threshold of vibration stability of soft mounted induction motors with elastic rotors and sleeve bearings fixed on active motor foot mounts for arbitrary controller structures T2 - 12th International Conference on Vibrations in Rotating Machinery N2 - In the paper an iterative calculation procedure is presented for deriving the threshold of vibration stability of induction motors with flexible shafts and sleeve bearings, mounted on soft steel frame foundations with active motor foot mounts and arbitrary controller structures. The mathematical model considers the electromagnetic influence, stiffness and internal damping of the rotor, stiffness and damping of the bearing housings with end shields, of the foundation and of the oil film of the sleeve bearings, as well as the stiffness and damping of the motor foot mounts and the controlled forces, which are applied by the motor foot mounts. KW - Induction motors KW - Active vibration control KW - Stability analysis KW - Sleeve bearings KW - Motor foot mounts Y1 - 2020 UR - https://www.taylorfrancis.com/chapters/oa-edit/10.1201/9781003132639-27 SN - 9781003132639 CY - CRC Press ER - TY - CHAP A1 - Werner, Ulrich ED - werner, ulrich T1 - Active vibration control of an induction motor with sleeve bearings and electrodynamic actuators between motor feet and steel frame foundation regarding electromagnetic excitation T2 - Journal of Physics: Conference Series N2 - The paper presents a theoretical analysis of active vibration control of an induction motor with sleeve bearings and electrodynamic actuators between motor feet and steel frame foundation, where the vertical vibration velocities of the motor feet are lead back to separate controllers. Based on a 2D model, the mathematical coherences of the controlled vibration system are presented, as well as a numerical example of a 2-pole induction motor. The threshold of vibration stability is calculated as well as frequency responses regarding bearing housing vibrations caused by electromagnetic forces in the air gap of the induction motor, due to a static magnetic eccentricity between rotor and stator. Also the actuator forces are analyzed. With this analysis, the effectiveness of the developed active vibration control system can be demonstrated. KW - Induction motors KW - Active vibration control KW - Current-controlled electrodynamic actuator KW - Electromagnetic excitation Y1 - 2024 U6 - https://doi.org/10.1088/1742-6596/2909/1/012001 IS - 2909 PB - IOP Publ. ER - TY - CHAP A1 - Wachter, Raimund A1 - Werner, Ulrich A1 - Herzog, Hans-Georg A1 - Bauer, Christian ED - Wachter, Raimund ED - Werner, Ulrich ED - Herzog, Hans-Georg ED - Bauer, Christian T1 - 1D-Simulation and experimental validation of active vibration damping of an induction motor mounted on an elastic steel frame foundation using modified integral controllers N2 - Preventing vibrations in electrical motors that are mounted on elastic foundations could help to open up operating speed ranges in which it was previously not allowed to operate as a permanent operating point. In the present paper, theoretical and practical aspects of an active vibration control of a two-pole induction motor (11 kW) mounted on a drive system and an elastic steel frame foundation are investigated. In preparation for simulating state space models with more degrees of freedom, a theoretical analysis derived from the existing test bench reduced to a two-mass-oscillator - motor, actuator and foundation - is done, to show which components are essential. Based on this analysis, simulations with a state space model and modified integral control algorithms will be discussed – in open and closed loop. Results of simulations of vibration reduction due to the control algorithm and disturbance response will be compared to experimental results from the test bench. Additionally, the power consumption of an actuator is analysed. KW - Induction motors KW - Active vibration control KW - Simulation KW - Experimental validation Y1 - 2022 UR - https://past.isma-isaac.be/downloads/isma2022/proceedings/Proceedings_ISMA-USD2022.pdf SP - 3605 EP - 3619 ER - TY - CHAP A1 - Wachter, Raimund A1 - Werner, Ulrich A1 - Herzog, Hans-Georg ED - Wachter, Raimund ED - Werner, Ulrich ED - Herzog, Hans-Georg T1 - Vibration analysis including active vibration control of a 11 kW two-pole induction motor with elastic steel frame foundation based on detailed 3D FE-models and experimental modal analyses N2 - This paper describes the vibration behaviour of a small 11 kW two pole induction motor, which is mounted on an elastic steel frame foundation with an active vibration control system (AVCS). On the one hand the paper presents detailed 3D finite element models for vibration analysis and compares the vibration simulation results to vibration measurement results and on the other hand, the paper presents a comparison of different settings of the test bench-motor mounted directly on the steel frame foundation and motor mounted on the developed AVCS. Further, the comparison of experimental modal analyses with open and close control loop operation are shown to demonstrate the efficiency of the AVCS. Finally, the paper gives an outlook about the scaling of the AVCS for motors in the megawatt range. KW - Induction motors KW - Active vibration control KW - Numerical vibration analysis KW - Experimental vibration analysis Y1 - 2025 UR - https://www.researchgate.net/publication/397130922 ER - TY - CHAP A1 - Wachter, Raimund A1 - Werner, Ulrich A1 - Herzog, Hans-Georg A1 - Bauer, Christian ED - Wachter, Raimund ED - Werner, Ulrich ED - Herzog, Hans-Georg ED - Bauer, Christian T1 - Analysis of the controller and damping behavior of an electrodynamic actuator system for an 11 kW two-pole induction motor on an elastic steel frame foundation N2 - This paper describes the open loop configuration of the simulation and measurement of a controller hardware and a voice coil actuator for vibration control of a 11 kW motor on steel frame foundation. The paper discusses the phase response regarding damping behavior of the actuator force and identifies approaches for improvements. Further, the paper offers a comparison of measurements as a result of the run up of the motor in open loop and closed loop operation with rubber elements and with steel springs. It is shown that all vibration modes with vertical movement at the motor feet can be reduced. Finally, the paper discusses the change in the system’s natural frequencies due to the replacement of the rubber elements by steel springs. KW - Induction motors KW - Active vibation control KW - Electrodynamic actuator KW - Induction motors KW - Active vibration control KW - Electrodynamic actuator Y1 - 2024 UR - https://ieeexplore.ieee.org/abstract/document/10652958 SN - 978-3-8007-6391-7 PB - Berlin CY - VDE ER -