Refine
Document Type
- Article (5)
Language
- English (5)
Publication reviewed
- begutachtet (5)
Keywords
- Bond strength (2)
- Friction surfacing (2)
- Inductive heating (2)
- Stainless steel (2)
- Additional Wires (1)
- Aluminium (1)
- Aluminium copper welding (1)
- Coating (1)
- Dissimilar material (1)
- Friction Stir Welding (1)
Institute
The implementation of friction crush welding (FCW) offers a versatile application in the welding of sheet metals. Three materials (EN AW 5754H22, DC01 and Cu-DHP) were analysed by applying the method with flanged edges. The additional material required to form the weld is provided by the flanged edges of the parent sheet metal. The joint is formed by the relative motion between a rotating disc, which is applied with a crushing force, and two sheet metal parts. The fundamental process variables and the requirements of the welding preparation are shown. Bond strengths, as a percentage of the yield strength of the parent material, of around 95% (DC01) 90% (EN AW 5754H22) and 62% (Cu-DHP) are achieved. Microstructural investigations reveal that a dynamic solid-state deformation and recrystallization of the additional flanged material results in a fine grain microstructure in the weld region. Reduced metallurgical changes along with minimized distortion and residual stresses in the parent material indicate low heat input. By creating a fine grain microstructure in the welding line, the friction crush welding method reveals great potential, especially for welding steel.
Joining sheet metal can be problematic using traditional friction welding techniques. Friction crush welding (FCW) offers a high speed process which requires a simple edge preparation and can be applied to out-of-plane geometries. In this work, an implementation of FCW was employed using an additional wire to weld sheets of EN AW5754 H22, DC01, and Cu-DHP. The joint is formed by bringing together two sheet metal parts, introducing a wire into the weld zone and employing a rotating disk which is subject to an external force. The requirements of the welding preparation and the fundamental process variables are shown. Thermal measurements were taken which give evidence about the maximum temperature in the welding center and the temperature in the periphery of the sheet metals being joined. The high welding speed along with a relatively low heat input results in a minimal distortion of the sheet metal and marginal metallurgical changes in the parent material. In the steel specimens, this FCW implementation produces a fine grain microstructure, enhancing mechanical properties in the region of the weld. Aluminum and copper produced mean bond strengths of 77 and 69 pct to that of the parent material, respectively, whilst the steel demonstrated a strength of 98 pct. Using a wire offers the opportunity to use a higher-alloyed additional material and to precisely adjust the additional material volume appropriate for a given material alignment and thickness.
Friction surfaced specimens produced by the application of inductive heating and utilising a flash-reducing tool were compared with those obtained through the classical approach. It was found that the use of inductive heating resulted in an increased consumption of the coating material; however, the push-off strength could be more than doubled when compared with the classical process with high shear strength values of up to 111 MPa. The application of the flash-reducing tool reduced the flash to less than 0.05% of the material deposited as a coating and manifested itself in the form of small chips. High push-off strength values of up to 135 MPa were observed, accompanied by an increased coating thickness, coating width and bonding area. Temperature measurements with thermocouples taken during the coating process showed that the melting temperature of the aluminium substrate was reached at the substrate–coating interface. Mixed mode failure was evident at the fractured surfaces of the push-off test specimens and mechanical interlocking appears to be a main bonding mechanism. The presence of cavities were shown to have a detrimental effect on the bonding integrity, but could be reduced in size and number by the application of the flash-reducing tool.
Inductive heating effects on friction surfacing of stainless steel onto an aluminium substrate
(2015)
An experimental setup was designed to compare the principal process parametric relationships with the classical approach to friction surfacing with the addition of inductive heating. The production of the flash is described quantitatively and its influence on coating geometry and mass is presented. It was found that the coating mass and thickness decreased for an increase in the rotational speed of the consumable rod; the amount of flash produced by the consumable rod also increased. However, the effect of an increase in this rod contact pressure on the coating thickness is insignificant, whilst the coating mass decreases with rising pressure and the coating width increases coupled with an increase in flash production. Cross sections showed good bonding quality and mechanical interlocking at the bond interface. The substrate-coating interface showed a varying degree of mechanical interlocking and the presence of cavitations. Bond strength values applying shear and push-off testing of up to 106 MPa and 96 MPa, respectively, could be identified.
Friction surfacing offers a means of producing coatings between dissimilar materials through a solid state process; a union that would otherwise be classed as incompatible for liquid state coating processes. A method of using a rotating consumable friction rod supplemented by inductive heating was employed to produce conditions necessary for a sound bond between a stainless steel coating and an aluminium substrate. The rotational speed of and load on the coating rod influenced the bond strength significantly with low rotational speeds and high load values producing a good bond quality; however, cavitations at the coating-substrate interface showed a detrimental effect on the bond quality. Mechanical interlocking could be identified from images of longitudinal cross-sectional slices which were recorded using optical microscopy. An image recognition software tool was used to generate an interfacial roughness profile graph which described the coating-substrate interface. Additional filtering of the profile graph showed the depth of mechanical interlocking of the stainless steel coating into the aluminium substrate with the degree of this interlocking quantified by roughness values calculated from the profile graph. Large roughness values can be related to high coating push-off strengths (up to 107 MPa), and also were a result of low rotational speeds and high load values during friction surfacing. Dovetail shaped mechanical interlocks identified in the profile produced both high push-off and shear strength when compared with wedge-shaped interlocks; which, overall, provided good shear strengths up to 126 MPa.