Fachbereich - Maschinenbau und Verfahrenstechnik
Refine
Year of publication
Document Type
- Conference Proceeding (15)
- Article (8)
- Part of a Book (6)
Language
- English (29) (remove)
Has Fulltext
- no (29)
Keywords
- energiBUS4home (2)
- Automated Control Concept (1)
- Boundary layer development (1)
- Chord Length (1)
- Combine Motion (1)
- Compressor (1)
- Computational Fluid Dynamics (1)
- Cycle Innovations (1)
- EBSILON®Professional (1)
- Energy (1)
Department/institution
- Fachbereich - Maschinenbau und Verfahrenstechnik (29) (remove)
High heat losses via exhaust gas and coolant in internal combustion engines (ICE) are the basis for numerous investigations regarding downstream processes for power generation. The most promising concepts are Organic Rankine Cycles (ORC) and Steam Rankine Cycles (SRC). In previous work of the Center of Innovative Energy Systems, Düsseldorf (Germany), the technical and economic feasibility of a low pressure SRC has been investigated and the advantages in comparison to organic Rankine cycles are highlighted. A distinctive feature of the cycle is the use of the ICE coolant heat for evaporation, which limits the cycles maximum steam pressure to values below atmospheric pressure. This work presents first results of a test rig with data reconciliation according to DIN 2048 to validate the simulation results and design calculations. As a basis for the experimental investigations, a gas fired CHP plant was selected. The design of the test rig is optimized for the operation in the laboratory, where the coolant heat is emulated by a tempering device and the exhaust heat of the CHP plant is emulated by a gas burner. With the designed test rig, it is possible to control the volume flow and the temperatures of the coolant and exhaust gas, so that different load conditions of the gas fired CHP plant can be investigated. For initial tests, the turbine in the SRC is replaced by a throttle to achieve the pressure drop of the turbine. The experimental results show, that the exhaust and coolant heat of a 36 kWel CHP plant can be emulated and the performance expectations of the cycle can be met in stable steady-state conditions. Based on the measurement results and the turbine design calculations an electric power output of the cycle of 3.8 kW will be possible, which results in a cycle efficiency of about 6.5 % and an increase of the electrical power output of the CHP plant of about 10 %. The results show that the plant concept is technically feasible and, with further optimization, also represents an alternative to ORC plants in terms of increasing the efficiency of a cogeneration plant.
Undergraduate students in engineering often have little exposure to the world of scientific publishing and the culture of sharing research work. While the beneficial exchange between research and teaching is well promoted, while the benefits of conference participation for students have already been surveyed and while courses on scientific writing are readily available, the concept of mini-conferences as part of the curriculum combines all three aspects into one. Therefore, the course "Engineering Conferences" was developed and installed as a mandatory part of a master program for engineering students. The idea is to go beyond simply teaching the standards of academic writing and skills for using scientific publications. By using a learner-centered approach, the students are engaged in typical activities around an active attendance of a real conference. Based on their bachelor thesis, they write a paper complying with common academic standards, submit the paper and review submissions of their fellow students. They also produce a poster and defend their work in a poster session held publicly on campus. This contribution is based on the experience from the first four terms teaching the course. It explains the didactic rationale behind the concept and individual teaching modules, it comprises the collection of useful resources for teaching and organizing scientific publishing and it includes the consequences drawn from course evaluation results.
In combination with a bottoming cycle, operated with a pure fluid in transcritical mode, the usage of a zeotropic mixture as a working fluid appears to be exergetically favorable for power cycle efficiency in cascaded two-stage organic Rankine cycles (CORC). A CORC is set up and initially tested with cyclopentane and propane as working fluids in its high temperature and low temperature cycle, respectively. A thermal oil cycle serves as the heat source and is powered electrically with a maximum heat flow of 158 kW. The design of this experimental setup allows for a rapid replacement of individual components and for a wide range of conditions in terms of fluids and thermodynamic states. The components of all cycles and the measurement and control technology are described in detail. A testing procedure is presented, followed by a discussion of the measurement results, where it is shown that the intended concept of two cascaded organic Rankine cycles is operational and that the measured data are consistent.
The ability to understand and predict the pressure losses of orifices is important in order to improve the air flow within the secondary air system. This experimental study investigates the behavior of the discharge coefficient for circular orifices with inlet cross flow which is a common flow case in gas turbines. Examples of this are at the inlet of a film cooling hole or the feeding of air to a blade through an orifice in a rotor disk. Measurements were conducted for a total number of 38 orifices, covering a wide range of length-to-diameter ratios, including short and long orifices with varying inlet geometries. Up to five different chamfer-to-diameter and radius-to-diameter ratios were tested per orifice length. Furthermore, the static pressure ratio across the orifice was varied between 1.05 and 1.6 for all examined orifices. The results of this comprehensive investigation demonstrate the beneficial influence of rounded inlet geometries and the ability to decrease pressure losses, which is especially true for higher cross flow ratios where the reduction of the pressure loss in comparison to sharp-edged holes can be as high as 54%. With some exceptions, the chamfered orifices show a similar behavior as the rounded ones but with generally lower discharge coefficients. Nevertheless, a chamfered inlet yields lower pressure losses than a sharp-edged inlet. The obtained experimental data were used to develop two correlations for the discharge coefficient as a function of geometrical as well as flow properties.
This paper deals with the design of a micro-scale ORC plant for teaching and research including the development of an automated control concept. The aim is to provide a safe and environmentally acceptable micro-scale heat engine, which can be developed, implemented and used in university labs for the education of students as well as for small research projects. The test rig allows the support of several learning outcomes on a multi-disciplinary level particularly for the implementation and simulation of small power systems. Special attention was given to the organic working fluid characteristics and its selection process. In addition to the above-mentioned performance goals, favourable safety properties and low global warming potential were decisive in the selection of the novel organic fluid called 3M™ Novec™ 649. The performance and the fluid behaviour of Novec 649 in a micro-scale power cycle are of major interest and the research goal for the test rig presented in this paper. Due to the expected power output of 1 kW, a scroll expander was chosen as the generator drive for the micro plant. In order to design the major parts of the ORC, the thermodynamic simulation software EBSILON®Professional was used. The supply temperature was set to 140 °C. As a result of the simulation, feasible expander inlet pressures spread from 5.5 bar to 8.5 bar. This leads to thermal efficiencies of the ORC in the order of 5 %. Adding a recuperator to the cycle system decreases the operating pressure range but in the end, the thermal efficiency can be increased by 1.5 %-points up to 6.2 %. Finally, an automated control concept is introduced, where the pump is controlled via the fill level measurement system.
The ability to understand and predict the pressure losses of orifices is important in order to improve the air flow within the secondary air system. This experimental study investigates the behavior of the discharge coefficient for circular orifices with inlet cross flow which is a common flow case in gas turbines. Examples of this are at the inlet of a film cooling hole or the feeding of air to a blade through an orifice in a rotor disk. Measurements were conducted for a total number of 38 orifices, covering a wide range of length-to-diameter ratios, including short and long orifices with varying inlet geometries. Up to five different chamfer-to-diameter and radius-to-diameter ratios were tested per orifice length. Furthermore, the static pressure ratio across the orifice was varied between 1.05 and 1.6 for all examined orifices. The results of this comprehensive investigation demonstrate the beneficial influence of rounded inlet geometries and the ability to decrease pressure losses, which is especially true for higher cross flow ratios where the reduction of the pressure loss in comparison to sharp-edged holes can be as high as 54%. With some exceptions, the chamfered orifices show a similar behavior as the rounded ones but with generally lower discharge coefficients. Nevertheless, a chamfered inlet yields lower pressure losses than a sharp-edged inlet. The obtained experimental data were used to develop two correlations for the discharge coefficient as a function of geometrical as well as flow properties.