Refine
Year of publication
Document Type
- Conference Proceeding (21) (remove)
Keywords
- energiBUS4home (2)
- Blue Engineering (1)
- Chord Length (1)
- Combine Motion (1)
- Diversität (1)
- EnerTEG (1)
- Engineering Conferences (1)
- Heizung (1)
- Laminar Separation Bubble (1)
- Lift Curve (1)
Department/institution
Thermodynamic simulation and experimental validation of a cascaded two-stage organic Rankine cycle
(2015)
The ability to understand and predict the pressure losses of orifices is important in order to improve the air flow within the secondary air system. This experimental study investigates the behavior of the discharge coefficient for circular orifices with inlet cross flow which is a common flow case in gas turbines. Examples of this are at the inlet of a film cooling hole or the feeding of air to a blade through an orifice in a rotor disk. Measurements were conducted for a total number of 38 orifices, covering a wide range of length-to-diameter ratios, including short and long orifices with varying inlet geometries. Up to five different chamfer-to-diameter and radius-to-diameter ratios were tested per orifice length. Furthermore, the static pressure ratio across the orifice was varied between 1.05 and 1.6 for all examined orifices. The results of this comprehensive investigation demonstrate the beneficial influence of rounded inlet geometries and the ability to decrease pressure losses, which is especially true for higher cross flow ratios where the reduction of the pressure loss in comparison to sharp-edged holes can be as high as 54%. With some exceptions, the chamfered orifices show a similar behavior as the rounded ones but with generally lower discharge coefficients. Nevertheless, a chamfered inlet yields lower pressure losses than a sharp-edged inlet. The obtained experimental data were used to develop two correlations for the discharge coefficient as a function of geometrical as well as flow properties.
Striving for smaller losses in turbomachinery has led to many advancements in the design of seals. Modern sealing concepts such as brush seals hold a great potential to increase the efficiency of both flight engines and stationary turbines. At the same time, in order to maintain stable operating conditions of the rotor, swirl-induced forces must be kept at a minimum in the sealing channels. Therefore, the influence of the permeable and flexible bristle pack of brush seals on the flow around the rotor surface must be known. In this paper the swirl flow in the cavities of two different seal geometries is studied experimentally and numerically. A conventional three-tooth labyrinth serves as a reference. A second seal arrangement with a bristle pack upstream of two teeth is compared with the reference labyrinth. The swirl is evaluated experimentally from total and static pressure measurements in various axial and circumferential positions. Additionally, the axial swirl distribution is calculated using computational fluid dynamics (CFD). Here, the numerical model of the brush seal is based on the porous medium approach and is calibrated using the experimental values of the leakage and the bristle clearance by adjusting the thickness of the bristle pack. The calibrated CFD model is then used to study the impact of the brush seal on the swirl component of the sealing flow. The observed significant decrease of the swirl by the brush seal shows good agreement with the experimental data. The impact of changes in bristle pack clearance on the swirl is also investigated and compared with experimental evidence. The aim is to show that the brush seals have a natural tendency to interrupt seal swirl. They can therefore be used for swirl control in order to create a beneficial impact on the dynamic stability of turbomachines.
This paper deals with the investigation in the technical and economic feasibility of a low-pressure steam cycle for the waste heat utilization of a combined heat and power (CHP) plant. The proposed steam cycle uses a pressure level below atmospheric pressure which allows to use the heat from the motor’s coolant for evaporation. The cycle is designed to increase the maximum electrical efficiency of a gas fired reciprocating engine and to increase operational flexibility for varying heat demand. Since organic Rankine cycle (ORC) plants are already being successfully used for waste heat recovery, advantages of the low-pressure steam Rankine cycle (SRC) over an ORC are highlighted. Many ORC fluids are toxic or flammable and thus have an increased risk potential compared to water. An additional advantage of water compared to ORC fluids is the possibility of superheating above 500 °C. The technical feasibility of the proposed cycle is studied by the detailed design of the individual system components such as turbine, heat exchangers and auxiliary parts. This includes the detailed thermodynamic design of the full cycle for the calculation of plant efficiencies. As a basis for future experimental investigations, a cogeneration plant with an electrical output of 50 kWel was selected as a heat source for the steam cycle. The design geometries of the turbine and the heat exchanger are presented along with efficiency and cost predictions. A subsonic radial turbine with a rotational speed of 155,000 rpm was selected. The maximum turbine output is about 7.5 kW. The use of a flash evaporator is investigated to reduce the size and the costs for the evaporator. The suggested steam cycle helps to increase the electrical efficiency of the CHP plant by 4.5% points from an original 36.5% to 41.0%. The steam cycle itself has an electrical efficiency of approximately 9%. Additionally, the condensation temperature in this steam cycle is high enough to be extracted as useful heat output to generate domestic water with a temperature of 50°C.
High heat losses via exhaust gas and coolant in internal combustion engines (ICE) are the basis for numerous investigations regarding downstream processes for power generation. The most promising concepts are Organic Rankine Cycles (ORC) and Steam Rankine Cycles (SRC). In previous work of the Center of Innovative Energy Systems, Düsseldorf (Germany), the technical and economic feasibility of a low pressure SRC has been investigated and the advantages in comparison to organic Rankine cycles are highlighted. A distinctive feature of the cycle is the use of the ICE coolant heat for evaporation, which limits the cycles maximum steam pressure to values below atmospheric pressure. This work presents first results of a test rig with data reconciliation according to DIN 2048 to validate the simulation results and design calculations. As a basis for the experimental investigations, a gas fired CHP plant was selected. The design of the test rig is optimized for the operation in the laboratory, where the coolant heat is emulated by a tempering device and the exhaust heat of the CHP plant is emulated by a gas burner. With the designed test rig, it is possible to control the volume flow and the temperatures of the coolant and exhaust gas, so that different load conditions of the gas fired CHP plant can be investigated. For initial tests, the turbine in the SRC is replaced by a throttle to achieve the pressure drop of the turbine. The experimental results show, that the exhaust and coolant heat of a 36 kWel CHP plant can be emulated and the performance expectations of the cycle can be met in stable steady-state conditions. Based on the measurement results and the turbine design calculations an electric power output of the cycle of 3.8 kW will be possible, which results in a cycle efficiency of about 6.5 % and an increase of the electrical power output of the CHP plant of about 10 %. The results show that the plant concept is technically feasible and, with further optimization, also represents an alternative to ORC plants in terms of increasing the efficiency of a cogeneration plant.