Refine
Labor/Institute
Keywords
- Femtosekundenlaser (35) (remove)
Document Type
- Article (26)
- Conference Proceeding (8)
- Other (1)
Sapphire is a robust and wear-resistant material. However, efficient and high-quality micromachining is still a challenge. This contribution demonstrates and discusses two novels, previously unreported approaches for femtosecond laser-based micromachining of rotational-symmetric sapphire workpieces, whereas both methods are in principal hybrids of laser scanning and laser turning or laser lathe. The first process, a combination of a sequential linear hatch pattern in parallel to the workpiece’s main axis with a defined incremental workpiece rotation, enables the fabrication of sapphire fibers with diameters of 50 µm over a length of 4.5 mm. Furthermore, sapphire specimens with a diameter of 25 µm over a length of 2 mm can be fabricated whereas an arithmetical mean height, i.e., Sa parameter, of 281 nm is achieved. The second process combines a constant workpiece feed and orthogonal scanning with incremental workpiece rotation. With this approach, workpiece length limitations of the first process are overcome and sapphire fibers with an average diameter of 90 µm over a length of 20 cm are manufactured. Again, the sapphire specimen exhibits a comparable surface roughness with an average Sa value of 249 nm over 20 cm. Based on the obtained results, the proposed manufacturing method paves an innovative and flexible, all laser-based way towards the fabrication or microstructuring of sapphire optical devices, and thus, a promising alternative to chemical processes.
We report on the laser ablation of cyclic olefin copolymer using an amplified ultrashort pulsed laser in the ultraviolet spectral range. In addition to a high ablation depth per laser-structured layer up to 74 μm at a fluence of 22 J cm−2, an excellent mean roughness 𝑅𝑎
of laser-patterned surfaces down to 0.5 μm is demonstrated. Furthermore, with increasing fluence, increasing ablation efficiencies up to 2.5 mm3 W−1 min−1 are determined. Regarding the quality of the ablation, we observed steep ablation flanks and low debris formation, though for fluences above 10.5 J cm−2 the formation of troughs was observed, being attributed to multiple reflections on the ablation flanks. For comparison, laser ablation was performed under identical conditions with an infrared laser wavelength. The results highlight that UV ablation exhibits significant advantages in terms of ablation efficiency, surface roughness and quality. Moreover, our results show that a larger UV focus spot accelerates the ablation process with comparable quality, paving the way for high-power UV ultrashort pulsed lasers towards an efficient and qualitative tool for the laser machining of cyclic olefin copolymer. The production of complex microfluidics further underlines the suitability of this type of laser.
This contribution demonstrates and discusses the preparation of finely dispersed copper(II) oxide nanosuspensions as precursors for reductive laser sintering (RLS). Since the presence of agglomerates interferes with the various RLS sub-processes, fine dispersion is required, and oversized particles must be identified by a measurement methodology. Aside from the established method of scanning electron microscopy for imaging individual dried particles, this work applies the holistic and statistically more significant laser diffraction in combination with dynamic image analysis in wet dispersion. In addition to direct ultrasonic homogenization, high-energy ball milling is introduced for RLS, to produce stable nanosuspensions with a high fine fraction, and, above all, the absence of oversize particles. Whereas ultrasonic dispersion stagnates at particle sizes between 500 nm and 20 μm, even after 8 h, milled suspension contains a high proportion of finest particles with diameters below 100 nm, no agglomerates larger than 1 μm and a trimodal particle size distribution with the median at 50 nm already, after 100 min of milling. The precursor layers produced by doctor blade coating are examined for their quality by laser scanning microscopy. The surface roughness of such a dry film can be reduced from 1.26 μm to 88 nm by milling. Finally, the novel precursor is used for femtosecond RLS, to produce homogeneous, high-quality copper layers with a sheet resistance of 0.28 Ω/sq and a copper mass concentration of 94.2%.
We report on ultraviolet ultrashort pulsed laser processing of silicon carbide. Laser ablated cavities are evaluated with respect to their ablation rates, surface roughness and overall quality by varying the laser pulse fluence. Using this type of laser, high edge quality and surface roughness down to 107 nm can be achieved with an ablation efficiency of up to 0.228 mm 3 W −1 min −1. Functional surfaces are produced by generating laser induced periodic surface structures. The comparison with infrared wavelength underlines the advantages of the ultraviolet wavelength for laser micro machining this material. Significant differences with respect to the measured ablation depths and roughness as well as generated micro-and nanostructures appear. While infrared ablation is dominated by a chipping mechanism above a critical fluence of 9.93 Jcm −2 , higher ablation rates are observed with strong quality losses at the same time. In comparison to the infrared emission wavelength, in general , a significantly higher processing quality is achieved with the ultraviolet emission wavelength. In addition, the influence of spot size and repetition rate in UV processing is investigated. By increasing these parameters, a process acceleration without quality losses is enabled. The generation of a sophisticated microstructure exemplifies the advantages of processing silicon carbide with the UV laser reported here.
We report on the acceleration of femtosecond reductive laser sintering of copper (II) oxide on the surface of transparent cyclic olefin copolymers (COC) by varying the focus size to generate metallic copper (Cu) layers. By using different focusing conditions, different process speeds are achieved, and the structural accuracies are controlled. The formation of Cu lines is observed for different focus sizes at various scan speeds, which is attributed to laser exposure duration and chemical reaction time. The formed lines are categorized and measured by optical microscopy and provide the basis for two-dimensional Cu surfaces. By hatching, high quality conductive films are produced with an increased focus diameter of up to 400 µm at a scan speed of 400 mm/s and a hatch distance of 250 µm resulting in a multiple increased process speed by a factor of thirteen compared to previous research. Using 4-tip measurement , a low sheet resistance of 0.165 Ω/sq was validated on these Cu films, which have an atomic Cu content of 89.5%.
In this contribution, we report on the generation of internal microchannels with basically unlimited channel length inside of PMMA bulk material by femtosecond laser. A precisely controllable and stable circular channel cross section is obtained by using a spatial light modulator to compensate the writing depth depending spherical aberration. Furthermore, the generation of a rotatable elliptical input beam by adaptive optics ensures a fitting of the beam shaping to the writing direction. In this study, we report on both, the effect of the ellipticity of the input beam and the effect of a correction of the spherical aberration on the circularity of the resulting internal microchannels. Moreover, we demonstrate the application of this writing technique by creating microfluidic testing structures inside of a transparent standard polymer.
While sapphire is one of the most durable materials, its properties entail that high-precision machining, especially in the sub-millimeter regime, is still challenging. This contribution demonstrates and discusses novel femtosecond laser-based micromachining approaches for the fabrication of rotational-symmetric sapphire workpieces, specifically the generation of optical fibers by means of laser lathe of sapphire rods and the practical realization of windmill fibers. In addition, volume refractive index modification in planar sapphire substrates is presented to induce photonic crystal waveguides. The micromachined structures are comprehensively examined with respect to geometric fidelity, surface roughness, refractive index modification, and potential optical waveguiding properties. All micromachining approaches are done by means of frequency-doubled or frequency-tripled femtosecond laser radiation. Different laser optical setups including laser scanning head, spatial beam profilers including a spatial light modulator and axial rotatory movement of the specimen are employed for micro structuring and in-depth refractive index modifications. In particular for laser lathe, a sophisticated scanning pattern, in combination with an incremental axial rotatory movement of the specimen, allows for the precise diameter reduction of sapphire rods with 250 µm diameter to fibers with outer diameters of 25 µm. By supporting the workpiece with a V-groove fixture, multi-mode fibers with lengths up to 20 cm can be processed with an average surface roughness of 250 nm. Additionally, an adapted ablation scanning sequence enables the first practical demonstration of sapphire windmill fibers. Furthermore, using a spatial light modulator allows for the adaption of the laser propagation properties as to enable volume refractive index modifications with free-form arrangement. Hexagonal patterns of refractive index modifications surrounding a pristine waveguide core are fabricated and single-mode waveguiding at 1550 nm is verified. Finally, the possibility of integrating Bragg gratings into this photonic waveguide type is demonstrated
Microfluidic lab on chip systems require components to transport, mix, separate and analyse small volumes of different fluids. In this study, we report on the laser generation of internal hollow architectures created by focused 514 nm femtosecond laser pulses inside PMMA bulk material. Size and cross-sectional shape of a single internal generated microchannel are determined by the intensity distribution inside the focal voxel and can be controlled either by the numerical aperture of the focusing objective or by laser beam shaping. As both approaches are practically limited with respect to the realizable cross-sectional shapes, we present a process based on an internal hatching to expand the achievable channel cross-sections and thereby enable the possibility to create complex 3D shaped internal structures. This process is applied to create fully internal functional microfluidic elements such as mixers which are part of most polymer lab-on-chip systems.
This contribution demonstrates and discusses electrically tunable polymer planar Bragg gratings based on bulk cyclic olefin copolymers. A lithographic single-writing-step method and femtosecond laser reductive sintering of copper(II) oxide nanoparticles are subsequently employed in order to generate buried photonic structures and copper conducting paths on top of the polymer substrate. This way, the necessary number of process steps for fabricating a planar polymer-based electro-optical device is greatly reduced. The response of a fully electrified grating structure follows temperature changes, induced by the copper conducting path, with sensitivities up to −31 pm K−1. Dilatometric measurements show that the specimen's behavior is correlated to the situationally reduced thermal expansion of the bulk polymer substrate. In consequence, the tuning response of the photonic platform follows a second order polynomial, whereas a direct current of 30 mA, which correlates to a power consumption of 18.3 mW, leads to a local temperature increase and a residual Bragg wavelength shift of 19.6 K and −547 pm, respectively. Moreover, the outstanding flexibility of the proposed fabrication concept is underlined by demonstrating alternative conducting path geometries, whereas one of the additional designs is adapted to control the spectral width of the Bragg grating's reflection peak.
Microneedle-based microfluidic systems have a great potential to become well-accepted medical devices for simple, accurate, and painless drug delivery and lab-on-a-chip diagnostics. In this work, we report on a novel hybrid approach combining femtosecond direct laser written microneedles with femtosecond laser generated microfluidic channels providing an important step towards versatile medical point-of-care systems. Hollow microneedle arrays are fabricated by a laser system designed for two-photon polymerization applications. Compression tests of two different types of truncated cone-shaped microneedle arrays prepared from OrmoComp® give information about the microneedle mechanical strength, and the results are compared to skin insertion forces. Three-dimensional microchannels are directly created inside PMMA bulk material by an ultrashort pulse laser system with vertical channels having adjustable cross-sectional areas, which allow attaching of microneedles to the microfluidic system. A comprehensive parameter study varying pulse duration and repetition rate is performed on two-photon polymerization to identify an optimal laser power range for fabricating microneedles using the same pulse duration and repetition rate as for microchannels. This addresses the advantage of a single laser system process that overcomes complex fabrication methods. A proof of concept flow test with a rhodamine B dye solution in distilled water demonstrates that the combination of microneedles and microchannels qualifies for microfluidic injection and extraction applications.
We report on laser direct generation of 3D-microchannels for microfluidic applications inside PMMA bulk material by focused femtosecond pulses. Inner lying channels with cross sectional areas from 100 µm2 to 4400 µm2 are directly created in the volume of a PMMA substrate. Using the presented process, the channel length is fundamentally unlimited. Here we demonstrate a channel length of 6 meters inside a substrate with dimensions of 20 × 20 × 1.1 mm. The formation of the micro channels is based on nonlinear absorption around the focal volume that triggers a material modification. The modified volume can be selectively opened to form the channel by a subsequent annealing process. The cross section of the channel is strongly influenced by the energy distribution and illumination around the focal volume determined by the optical setup and process design. The 3D channel layout can easily be realized by moving the specimen using 3D motorized stage, allowing freely chosen complex shaped channel architectures. Within a comprehensive parameter study, varying laser power, number of multi-passes, writing speed and writing depths, we identify an optimized process in terms of attainable channel height, width and aspect ratio, as well as process stability and reproducibility. The proof of concept for an application in three dimensional microfluidic systems is provided by florescence microscopy using a dye rhodamine B solution in isopropanol.
The authors report on the laser generation of three-dimensional microchannel architectures with fundamentally unlimited channel length by focused 514 nm femtosecond laser pulses inside polymethylmethacrylate bulk material. The three-dimensional channel layout is implemented by moving the specimen using three-dimensional motorized stages, allowing freely chosen complex shaped channel architectures. Based on nonlinear absorption of high intensities around the focal volume, a material modification, including a refractive-index shift is triggered. After laser exposure, the channel is created by a gaseous degradation of exposed areas during an annealing process. Cross section and aspect ratio of thus generated microchannels are strongly influenced by the numerical aperture of the applied objective. To obtain a circular cross-sectional shape, high focusing objectives are necessary. In this report, the authors improve the existing setup by using an elliptical input beam, transforming the intensity distribution of the focal area in the propagation direction to a circular shape even for low and medium numerical aperture focusing objectives and therefore avoiding a small working distance as a limiting factor for processing depth. The elliptical input beam is obtained by insertion of a slit mask in front of the focusing objective. The ellipticity of the incident beam defines the aspect ratio of the generated microchannels. Furthermore, the size of internal microchannels is adjustable by varying laser and annealing process parameters.
We report on laser generation of microchannels by focused femtosecond laser pulses inside PMMA bulk material. This process enables direct fabrication of three dimensional microfluidic channel architectures with generally unlimited channel length. Based on nonlinear ultrashort pulse laser absorption of high intensities around the focal volume, a material modification including a refractive index shift is triggered. After laser exposure the channel is created by a gaseous degradation of exposed areas during an annealing process. The 3D channel layout can easily be realized by moving the specimen using 3D motorized stages, allowing freely chosen complex shaped channel architectures. In this report, the creation of inner lying vertical microchannels is examined. In addition to previously shown horizontal channel architectures vertical channels are necessary to fulfill the definition of an internal three-dimensional microfluidic structure and to create interconnections in multilevel lab on chip devices. The cross section and geometry of vertical channels are strongly influenced by laser parameters such as pulse duration, laser power and writing speed. The influence of these process parameters on the channels diameter is determined and parameters are optimized regarding a controllable, stable and reproducible process. The functionality of vertical microchannels as an interconnection between multilayer microfluidic devices is demonstrated using a Rhodamine B solution.
Control of femtosecond laser generated microfluidic channels inside poly (methyl methacrylate)
(2018)
In this study, the authors report on femtosecond laser direct generation of microchannels inside poly(methyl methacrylate) with variable dimensions ranging from a channel height of 20 to 350 μm and an aspect ratio down to 1.2. Focused ultrashort laser pulses are used to trigger a material modification in the focal area which can be selectively opened by a subsequent annealing process. A 3D microchannel architecture can easily be realized by moving the specimen using motorized stages, allowing freely chosen complex shaped channel layouts. While the laser wavelength is identified as one of the main parameters determining process effectiveness, another core of this study is the variation of channel dimensions by the numerical aperture of the applied objective to focus the laser. The authors find that both size and shape of the modified region and the resulting microchannel can be controlled by altering the numerical aperture.
We report on the joining of transparent thermoplastic polymers using infrared femtosecond laser pulses. Due to nonlinear absorption, the developed micro-welding process for cyclo-olefin copolymers does not require any intermediate absorbing layers or any surface pre-processing of the welding partners. In view of an optimized and stable micro-welding process, the influence of the welding speed and focal position on both, the quality and shear force strength are investigated. We highlight that welding seam widths of down to 65 µm are feasible for welding speeds of up to 75 mm/s. However, a variation of the welding speed affects the required focal position for a successful joining process. The shear force strength of the welding seam is determined to 37 MPa, which corresponds to 64% of the shear strength of the bulk material and is not affected by the welding speed.
Based on nonlinear absorption, we report on laser welding of cycloolefin copolymers without any additional absorption layer employing infrared femtosecond laser. To the best of our knowledge, this is the first report of ultrashort laser welding of this material class, revealing a remarkable high processing speed of 20 mm/s in a single pass mode. Using a 1028 nm laser having a pulse duration of 220 fs at a repetition rate of 571 kHz leads to a welding seam width between 38 and 137 μm, depending on the applied laser average power. The welded joint is characterized by a maximum shear strength of 40 MPa. The experimental results are compared to those reported for femtosecond laser welding of PMMA and to those published for using a Thulium fiber laser.