Refine
Labor/Institute
Keywords
- Femtosekundenlaser (33)
- Bragg-Reflektor (25)
- Laserschneiden (22)
- Laserbearbeitung (16)
- Faserlaser (15)
- Lumineszenzdiode (14)
- Ultrakurzzeitlaser (14)
- Quarzglas (8)
- Dünne Schicht (7)
- Laser (7)
Year of publication
Document Type
- Article (97)
- Conference Proceeding (59)
- Other (3)
- Part of a Book (1)
Has Fulltext
- no (160) (remove)
Limited process control can cause metallurgical defect formation and inhomogeneous relative density in laser powder bed fusion manufactured parts. This study shows that process monitoring, based on optical melt-pool signal analysis is capable of tracing relative density variations: Unsupervised machine learning, applied to cluster multiple-slice monitoring data, reveals characteristic patterns in this noisy time-series signal, which can be co-registered with geometrical positions in the build part. For cylindrical 15–5 PH stainless steel specimens, manufactured under constant process parameters and post-analyzed by µ-computer tomography, correlations between such patterns and an increased local relative density at the edge have been observed. Finite element method (FEM) modeling of thermal histories at exemplary positions close to the edge suggest pre-heating effects caused by neighboring laser scan trajectories as possible reasons for the increased melt pool intensity at the edge.
We report on the laser ablation of cyclic olefin copolymer using an amplified ultrashort pulsed laser in the ultraviolet spectral range. In addition to a high ablation depth per laser-structured layer up to 74 μm at a fluence of 22 J cm−2, an excellent mean roughness 𝑅𝑎
of laser-patterned surfaces down to 0.5 μm is demonstrated. Furthermore, with increasing fluence, increasing ablation efficiencies up to 2.5 mm3 W−1 min−1 are determined. Regarding the quality of the ablation, we observed steep ablation flanks and low debris formation, though for fluences above 10.5 J cm−2 the formation of troughs was observed, being attributed to multiple reflections on the ablation flanks. For comparison, laser ablation was performed under identical conditions with an infrared laser wavelength. The results highlight that UV ablation exhibits significant advantages in terms of ablation efficiency, surface roughness and quality. Moreover, our results show that a larger UV focus spot accelerates the ablation process with comparable quality, paving the way for high-power UV ultrashort pulsed lasers towards an efficient and qualitative tool for the laser machining of cyclic olefin copolymer. The production of complex microfluidics further underlines the suitability of this type of laser.
This contribution demonstrates and discusses the preparation of finely dispersed copper(II) oxide nanosuspensions as precursors for reductive laser sintering (RLS). Since the presence of agglomerates interferes with the various RLS sub-processes, fine dispersion is required, and oversized particles must be identified by a measurement methodology. Aside from the established method of scanning electron microscopy for imaging individual dried particles, this work applies the holistic and statistically more significant laser diffraction in combination with dynamic image analysis in wet dispersion. In addition to direct ultrasonic homogenization, high-energy ball milling is introduced for RLS, to produce stable nanosuspensions with a high fine fraction, and, above all, the absence of oversize particles. Whereas ultrasonic dispersion stagnates at particle sizes between 500 nm and 20 μm, even after 8 h, milled suspension contains a high proportion of finest particles with diameters below 100 nm, no agglomerates larger than 1 μm and a trimodal particle size distribution with the median at 50 nm already, after 100 min of milling. The precursor layers produced by doctor blade coating are examined for their quality by laser scanning microscopy. The surface roughness of such a dry film can be reduced from 1.26 μm to 88 nm by milling. Finally, the novel precursor is used for femtosecond RLS, to produce homogeneous, high-quality copper layers with a sheet resistance of 0.28 Ω/sq and a copper mass concentration of 94.2%.
Evaluation of an ultrashort pulsed laser robot system for flexible and large-area micromachining
(2023)
We report for the first time on the realization, characterization and application of an ultrashort pulsed laser robot system for flexible and large-area 2D and 3D laser micromachining with 6 articulated axes. To characterize the dynamic positioning of the laser beam during and after axes movement, CMOS image sensors were integrated into the beam path. A method introduced for the alignment of the optical axes allows a reduction of the deviations in laser beam positioning to less than 141.8 ± 92.9 μm within a 110° rotation range of axis 4. In addition, a high laser beam positioning repeatability of less than 102.2 μm is demonstrated over a total period of 14 h for a movement of axis 5 within a range of 0° to 90°. Initial laser cutting, laser structuring and laser marking applications on automotive dashboards and glass substrates are presented for flexible and large area 2D and 3D manufacturing. By applying a special laser cutting strategy for processing AF 32 eco thin glass, high cutting quality is achieved with a taper of up to 96.3% without the generation of cracks, demonstrating the innovative potential of the high-precision laser robot system. Nonetheless, different identified inherent influences of each axis 1–5 during robot axis movement demand for an innovative beam stabilization concept to achieve high precision in laser beam positioning.
We report on an experimental study of laser microvia percussion drilling of Ajinomoto build-up film (ABF) material using an ultrashort pulsed laser in the ultraviolet region. In order to optimize the drilling quality in terms of the fabricated taper and microvia diameter, the
MHz burst mode is used in combination with both a Gaussian and a top-hat laser intensity distribution. To evaluate the influence of the top-hat beam shape on defocusing, microvias were drilled at different z-positions in the range of 200 μm evenly distributed around the focal plane. The drilling quality was evaluated by laser scanning microscopy and metallography. When using a top-hat beam shape, a reduced taper of down to 26.8 % on average is achieved compared to a Gaussian beam. For the application of 3 intra-burst pulses, we find an improvement of the taper by 11.6% compared to the single pulse mode due to the increasing heat accumulation. Using a top-hat beam shape in combination with the MHz burst mode, an 18.2 % reduction in laser drilling time for a microvia with a similar taper is remarkable, demonstrating the high potential for scaling throughput in electronics manufacturing.
We demonstrate and discuss the integration of Bragg gratings in aerosol-jetted polymer optical waveguides, produced in the optical assembly and connection technology for component-integrated bus systems (OPTAVER) process. By using a femtosecond laser and adaptive beam shaping, an elliptical focal voxel generates different types of single pulse modification by nonlinear absorption in the waveguide material, which are arranged periodically to form Bragg gratings. Integration of a single grating structure or, alternatively, an array of Bragg grating structures in the multimode waveguide yields a pronounced reflection signal with typical multimodal properties, i.e., a number of reflection peaks with non-Gaussian shapes. However, the main wavelength of reflection, located around 1555 nm, is evaluable by means of an appropriate smoothing algorithm. When loaded by mechanical bending, a pronounced Bragg wavelength shift of this reflected peak up to 160 pm is detected. This demonstrates that the additively manufactured waveguides can be used not only for signal transmission but also as a sensor.
We report on ultraviolet ultrashort pulsed laser processing of silicon carbide. Laser ablated cavities are evaluated with respect to their ablation rates, surface roughness and overall quality by varying the laser pulse fluence. Using this type of laser, high edge quality and surface roughness down to 107 nm can be achieved with an ablation efficiency of up to 0.228 mm 3 W −1 min −1. Functional surfaces are produced by generating laser induced periodic surface structures. The comparison with infrared wavelength underlines the advantages of the ultraviolet wavelength for laser micro machining this material. Significant differences with respect to the measured ablation depths and roughness as well as generated micro-and nanostructures appear. While infrared ablation is dominated by a chipping mechanism above a critical fluence of 9.93 Jcm −2 , higher ablation rates are observed with strong quality losses at the same time. In comparison to the infrared emission wavelength, in general , a significantly higher processing quality is achieved with the ultraviolet emission wavelength. In addition, the influence of spot size and repetition rate in UV processing is investigated. By increasing these parameters, a process acceleration without quality losses is enabled. The generation of a sophisticated microstructure exemplifies the advantages of processing silicon carbide with the UV laser reported here.
We report on the acceleration of femtosecond reductive laser sintering of copper (II) oxide on the surface of transparent cyclic olefin copolymers (COC) by varying the focus size to generate metallic copper (Cu) layers. By using different focusing conditions, different process speeds are achieved, and the structural accuracies are controlled. The formation of Cu lines is observed for different focus sizes at various scan speeds, which is attributed to laser exposure duration and chemical reaction time. The formed lines are categorized and measured by optical microscopy and provide the basis for two-dimensional Cu surfaces. By hatching, high quality conductive films are produced with an increased focus diameter of up to 400 µm at a scan speed of 400 mm/s and a hatch distance of 250 µm resulting in a multiple increased process speed by a factor of thirteen compared to previous research. Using 4-tip measurement , a low sheet resistance of 0.165 Ω/sq was validated on these Cu films, which have an atomic Cu content of 89.5%.
In this contribution, we report on the generation of internal microchannels with basically unlimited channel length inside of PMMA bulk material by femtosecond laser. A precisely controllable and stable circular channel cross section is obtained by using a spatial light modulator to compensate the writing depth depending spherical aberration. Furthermore, the generation of a rotatable elliptical input beam by adaptive optics ensures a fitting of the beam shaping to the writing direction. In this study, we report on both, the effect of the ellipticity of the input beam and the effect of a correction of the spherical aberration on the circularity of the resulting internal microchannels. Moreover, we demonstrate the application of this writing technique by creating microfluidic testing structures inside of a transparent standard polymer.
While sapphire is one of the most durable materials, its properties entail that high-precision machining, especially in the sub-millimeter regime, is still challenging. This contribution demonstrates and discusses novel femtosecond laser-based micromachining approaches for the fabrication of rotational-symmetric sapphire workpieces, specifically the generation of optical fibers by means of laser lathe of sapphire rods and the practical realization of windmill fibers. In addition, volume refractive index modification in planar sapphire substrates is presented to induce photonic crystal waveguides. The micromachined structures are comprehensively examined with respect to geometric fidelity, surface roughness, refractive index modification, and potential optical waveguiding properties. All micromachining approaches are done by means of frequency-doubled or frequency-tripled femtosecond laser radiation. Different laser optical setups including laser scanning head, spatial beam profilers including a spatial light modulator and axial rotatory movement of the specimen are employed for micro structuring and in-depth refractive index modifications. In particular for laser lathe, a sophisticated scanning pattern, in combination with an incremental axial rotatory movement of the specimen, allows for the precise diameter reduction of sapphire rods with 250 µm diameter to fibers with outer diameters of 25 µm. By supporting the workpiece with a V-groove fixture, multi-mode fibers with lengths up to 20 cm can be processed with an average surface roughness of 250 nm. Additionally, an adapted ablation scanning sequence enables the first practical demonstration of sapphire windmill fibers. Furthermore, using a spatial light modulator allows for the adaption of the laser propagation properties as to enable volume refractive index modifications with free-form arrangement. Hexagonal patterns of refractive index modifications surrounding a pristine waveguide core are fabricated and single-mode waveguiding at 1550 nm is verified. Finally, the possibility of integrating Bragg gratings into this photonic waveguide type is demonstrated
While Bragg grating-based optical devices have shown promising performances for pressure sensing applications, their sensitivity, especially in the low-pressure regime, is unsatisfying and needs to be optimized by elaborate designs, such as cantilevers or other extrinsic mechanical transducers. This contribution demonstrates and discusses a novel concept for optical pressure sensors based on polymer planar Bragg gratings. Waveguide and Bragg grating are fabricated underneath the surface of a temperature-stable and humidity-insensitive cyclic olefin copolymer substrate by means of a femtosecond laser. Based on the employed direct-writing procedure, in combination with adaptive, in-situ beam shaping with a spatial light modulator, writing depth, i.e., location of the photonic structures within the substrate, as well as Bragg grating periodicity and positioning can be deliberately chosen. Afterwards, the polymer substrate is post-processed with a high-precision micro mill, so a diaphragm comprising the integrated photonic structures is generated. The resulting diaphragm exhibits a thickness of 300 µm and a diameter of 10 mm. Finally, the optical sensor is packaged and sealed to form an air-filled gas pocket underneath the diaphragm. Deformations of the diaphragm by external pressure changes translate to strain variations along the waveguide axis and thus perturb the Bragg grating period. This leads to changes in the grating’s wavelength of main reflection, which can be evaluated in order to quantify the relative external pressure. With this straightforward optical sensor concept, pressure sensitivities up to 39 pm kPa-1, within relative pressures ranges from 78 kPa to 372 kPa, are achieved.
Microfluidic lab on chip systems require components to transport, mix, separate and analyse small volumes of different fluids. In this study, we report on the laser generation of internal hollow architectures created by focused 514 nm femtosecond laser pulses inside PMMA bulk material. Size and cross-sectional shape of a single internal generated microchannel are determined by the intensity distribution inside the focal voxel and can be controlled either by the numerical aperture of the focusing objective or by laser beam shaping. As both approaches are practically limited with respect to the realizable cross-sectional shapes, we present a process based on an internal hatching to expand the achievable channel cross-sections and thereby enable the possibility to create complex 3D shaped internal structures. This process is applied to create fully internal functional microfluidic elements such as mixers which are part of most polymer lab-on-chip systems.