Refine
Labor/Institute
Keywords
- Femtosekundenlaser (8) (remove)
Document Type
- Conference Proceeding (8) (remove)
Has Fulltext
- no (8)
Reviewed
- nein (3)
We report on ultraviolet ultrashort pulsed laser processing of silicon carbide. Laser ablated cavities are evaluated with respect to their ablation rates, surface roughness and overall quality by varying the laser pulse fluence. Using this type of laser, high edge quality and surface roughness down to 107 nm can be achieved with an ablation efficiency of up to 0.228 mm 3 W −1 min −1. Functional surfaces are produced by generating laser induced periodic surface structures. The comparison with infrared wavelength underlines the advantages of the ultraviolet wavelength for laser micro machining this material. Significant differences with respect to the measured ablation depths and roughness as well as generated micro-and nanostructures appear. While infrared ablation is dominated by a chipping mechanism above a critical fluence of 9.93 Jcm −2 , higher ablation rates are observed with strong quality losses at the same time. In comparison to the infrared emission wavelength, in general , a significantly higher processing quality is achieved with the ultraviolet emission wavelength. In addition, the influence of spot size and repetition rate in UV processing is investigated. By increasing these parameters, a process acceleration without quality losses is enabled. The generation of a sophisticated microstructure exemplifies the advantages of processing silicon carbide with the UV laser reported here.
We report on the acceleration of femtosecond reductive laser sintering of copper (II) oxide on the surface of transparent cyclic olefin copolymers (COC) by varying the focus size to generate metallic copper (Cu) layers. By using different focusing conditions, different process speeds are achieved, and the structural accuracies are controlled. The formation of Cu lines is observed for different focus sizes at various scan speeds, which is attributed to laser exposure duration and chemical reaction time. The formed lines are categorized and measured by optical microscopy and provide the basis for two-dimensional Cu surfaces. By hatching, high quality conductive films are produced with an increased focus diameter of up to 400 µm at a scan speed of 400 mm/s and a hatch distance of 250 µm resulting in a multiple increased process speed by a factor of thirteen compared to previous research. Using 4-tip measurement , a low sheet resistance of 0.165 Ω/sq was validated on these Cu films, which have an atomic Cu content of 89.5%.
While sapphire is one of the most durable materials, its properties entail that high-precision machining, especially in the sub-millimeter regime, is still challenging. This contribution demonstrates and discusses novel femtosecond laser-based micromachining approaches for the fabrication of rotational-symmetric sapphire workpieces, specifically the generation of optical fibers by means of laser lathe of sapphire rods and the practical realization of windmill fibers. In addition, volume refractive index modification in planar sapphire substrates is presented to induce photonic crystal waveguides. The micromachined structures are comprehensively examined with respect to geometric fidelity, surface roughness, refractive index modification, and potential optical waveguiding properties. All micromachining approaches are done by means of frequency-doubled or frequency-tripled femtosecond laser radiation. Different laser optical setups including laser scanning head, spatial beam profilers including a spatial light modulator and axial rotatory movement of the specimen are employed for micro structuring and in-depth refractive index modifications. In particular for laser lathe, a sophisticated scanning pattern, in combination with an incremental axial rotatory movement of the specimen, allows for the precise diameter reduction of sapphire rods with 250 µm diameter to fibers with outer diameters of 25 µm. By supporting the workpiece with a V-groove fixture, multi-mode fibers with lengths up to 20 cm can be processed with an average surface roughness of 250 nm. Additionally, an adapted ablation scanning sequence enables the first practical demonstration of sapphire windmill fibers. Furthermore, using a spatial light modulator allows for the adaption of the laser propagation properties as to enable volume refractive index modifications with free-form arrangement. Hexagonal patterns of refractive index modifications surrounding a pristine waveguide core are fabricated and single-mode waveguiding at 1550 nm is verified. Finally, the possibility of integrating Bragg gratings into this photonic waveguide type is demonstrated
Microfluidic lab on chip systems require components to transport, mix, separate and analyse small volumes of different fluids. In this study, we report on the laser generation of internal hollow architectures created by focused 514 nm femtosecond laser pulses inside PMMA bulk material. Size and cross-sectional shape of a single internal generated microchannel are determined by the intensity distribution inside the focal voxel and can be controlled either by the numerical aperture of the focusing objective or by laser beam shaping. As both approaches are practically limited with respect to the realizable cross-sectional shapes, we present a process based on an internal hatching to expand the achievable channel cross-sections and thereby enable the possibility to create complex 3D shaped internal structures. This process is applied to create fully internal functional microfluidic elements such as mixers which are part of most polymer lab-on-chip systems.
Lab-on-chip systems are based on components to transport, mix, separate and analyse small volumes of different fluids. The consecutive integration of more complex functions into a single and compact chip demands on multilayer systems. As the classical production using a stacking and joining of single processed layers is elaborate and limited in terms of multilayer structures, an uprising trend to fabricate those devices is the internal, three dimensional processing of transparent substrates by using ultrashort laser pulses. In this study, we report on the generation of internal hollow architectures created by focused 514nm femtosecond laser pulses inside optical polymer bulk materials of different polymers. The three-dimensional channel layout is implemented by moving the sample using three-dimensional motorized stages, allowing arbitrary complex shaped internal channel architectures. Size and cross sectional shape of a single internal generated microchannel are determined by the intensity distribution of the focal voxel. In particular, we show a comprehensive parameter study to improve this laser process with respect to a higher processing speed and stability.