TY - JOUR A1 - Küchler, Andreas A1 - Schwab, A. T1 - Zum Begriff der Netzfrequenz bei Netzstörungen JF - Elektrizitätswirtschaft Y1 - 1987 UR - http://permalink.bibkatalog.de/BV002576215 VL - 86 SP - 308 EP - 310 ER - TY - JOUR A1 - Küchler, Andreas T1 - Master Research Program Elektro- und Informationstechnik JF - DNH Die Neue Hochschule Y1 - 2007 UR - http://permalink.bibkatalog.de/BV002668906 VL - 47 IS - 3/06 SP - 12 EP - 14 ER - TY - JOUR A1 - Küchler, Andreas T1 - Induktivität von Hochspannungskondensatoren JF - etz Elektrotechnische Zeitschrift Y1 - 1998 UR - http://permalink.bibkatalog.de/BV002580706 VL - 109 SP - 1070 EP - 1075 ER - TY - CHAP A1 - Küchler, Andreas T1 - Application of HV Test Methods to the Evaluation of LV Motor Insulation Quality BT - optim ‘98 T2 - 6th Int. Conf. on Optimization of Electrical and Electronic Equipment Y1 - 1998 CY - Brasov, Romania ER - TY - JOUR A1 - Küchler, Andreas A1 - Bedel, T. T1 - Dielectric Diagnosis of Water Content in Transformer Insulation Systems JF - ETEP European Trans. on El. Power Y1 - 2001 VL - 11 IS - 1 PB - VDE CY - Offenbach ER - TY - CHAP A1 - Dahinden, V. A1 - Schultz, K. A1 - Küchler, Andreas T1 - The Function of Solid Insulation in Transformers T2 - Transform ‘98 Y1 - 1998 CY - München ER - TY - JOUR A1 - Hartmann, Jürgen A1 - Edler, F. A1 - Anhalt, Klaus T1 - Neuartige eutektische Metall-Kohlenstoff-Hochtemperaturfixpunkte für die Thermometrie JF - PTB Mitteilungen Y1 - 2007 UR - http://permalink.bibkatalog.de/BV035078972 VL - 117 IS - 3 SP - 256 EP - 260 ER - TY - CHAP A1 - Küchler, Andreas A1 - Rashwan, M.M. A1 - McDermid, W. A1 - Hammer, F. T1 - On the Design, Testing and Operating Experience of Composite Dry Bushings in HVDC T2 - 5th Int. Conf. on AC and DC Power Transmission Y1 - 1991 CY - London ER - TY - CHAP A1 - Küchler, Andreas A1 - Hammer, F. T1 - Suppression of Surface Discharges and Flashover on Dielectric Surfaces BT - 9th ISH Int. Symp. on High Voltage Engineering Y1 - 1995 IS - 8032 CY - Graz, Österreich ER - TY - CHAP A1 - Küchler, Andreas A1 - Hammer, F. T1 - Insulating Systems for HVDC Power Apparatus T2 - 3rd Int. Conf. on Properties Y1 - 1995 CY - Graz, Österreich ER - TY - CHAP A1 - Küchler, Andreas A1 - Hammer, F. T1 - Application of Dielectric Materials Y1 - 1991 SP - 965 EP - 968 CY - Tokyo ER - TY - JOUR A1 - Hartmann, Jürgen A1 - Taubert, Dieter Richard A1 - Monte, C. A1 - Gutschwager, B. A1 - Baltruschat, C. A1 - Hollandt, Jörg A1 - Kochems, D. A1 - Küchel, C. T1 - The Spectral Photon Flux of the Radiometric Calibration Spectral Source for the NIRSpec Instrument of the James Webb Space Telescope JF - Metrologia Y1 - 2009 UR - http://permalink.bibkatalog.de/BV012573233 IS - 46 SP - 207 EP - 212 ER - TY - JOUR A1 - Hartmann, Jürgen A1 - Thomas, R. A1 - Hill, K.D. A1 - Steele, A.G. A1 - Ma, C.K. T1 - Bilateral comparison of the NRC and PTB local realizations of the ITS-90 between the silver point and 1700 °C using vacuum tungsten strip lamps as transfer standards JF - Metrologia Y1 - 2006 UR - http://permalink.bibkatalog.de/BV012573233 VL - 43 IS - 03003 ER - TY - JOUR A1 - Hartmann, Jürgen A1 - Friedrich, R. A1 - Taubert, Dieter Richard A1 - Hollandt, Jörg T1 - Improved calibration of the spectral responsivity of interference filter radiometers in the visible and near infrared spectral range at PTB JF - Metrologia Y1 - 2003 UR - http://permalink.bibkatalog.de/BV012573233 IS - 40 SP - 35 EP - 38 ER - TY - JOUR A1 - Hartmann, Jürgen A1 - Anhalt, Klaus A1 - Zelenjuk, A. A1 - Taubert, Dieter Richard T1 - New PTB Set-up for the absolute calibration of the spectral responsivity of radiation thermometers JF - International Journal of Thermophysics Y1 - 2009 UR - http://permalink.bibkatalog.de/BV013298193 IS - 30 SP - 192 EP - 202 ER - TY - JOUR A1 - Hartmann, Jürgen A1 - Ma, C.K. A1 - Gibson, C. T1 - Decreasing dependence of the calibration of the tungsten strip lamp on the temperature of the lamp base with increasing filament length JF - Metrologia Y1 - 2005 UR - http://permalink.bibkatalog.de/BV012573233 IS - 42 SP - 383 EP - 388 ER - TY - JOUR A1 - Hartmann, Jürgen A1 - Anhalt, Klaus A1 - Wang, Y. A1 - Yamada, Y. T1 - Large and small aperture Fixed-point cells of Cu, Pt-C, and Re-C JF - International Journal of Thermophysics Y1 - 2008 UR - http://permalink.bibkatalog.de/BV013298193 IS - 29 SP - 969 EP - 983 ER - TY - JOUR A1 - Hartmann, Jürgen A1 - Werner, L. T1 - Radiation thermometry towards the triple point of water? JF - International Journal of Thermophysics Y1 - 2008 UR - http://permalink.bibkatalog.de/BV013298193 IS - 29 SP - 1052 EP - 1065 ER - TY - JOUR A1 - Hartmann, Jürgen T1 - Correct consideration of the index of refraction using blackbody radiation JF - Optics Express Y1 - 2006 UR - http://permalink.bibkatalog.de/BV013253264 VL - 14 IS - 18 SP - 8121 EP - 8126 ER - TY - JOUR A1 - Hartmann, Jürgen T1 - Advanced comparator method for measuring ultra small aperture areas JF - Meas.Sci.Techn. Y1 - 2001 IS - 12 SP - 1678 EP - 1682 ER - TY - CHAP A1 - Wirth, Isabell A1 - Reumann, Andreas A1 - Küchler, Andreas A1 - Schnitzler, Tim A1 - Langens, Achim A1 - Berger, Frank A1 - Zink, Markus H. T1 - Steady-state and Transient Electrical Potential Distribution in HVDC Bushings Measured under Different Thermal Conditions T2 - 19th International Symposium on High Voltage Engineering Y1 - 2015 CY - Pilsen, Czech Republic ER - TY - BOOK A1 - Zink, Markus H. T1 - Zustandsbewertung betriebsgealterter Hochspannungstransformatordurchführungen mit Öl-Papier-Dielektrikum mittels dielektrischer Diagnose BT - Dissertation Technische Universität Ilmenau Y1 - 2013 UR - http://permalink.bibkatalog.de/BV041616215 PB - Universitätsverlag Ilmenau CY - Ilmenau ER - TY - JOUR A1 - Hartmann, Jürgen A1 - Lowe, D. A1 - Anhalt, Klaus T1 - Construction and validation of a platinum-carbon eutectic fixed-point JF - Metrologia Y1 - 2008 UR - http://permalink.bibkatalog.de/BV012573233 IS - 45 SP - 325 EP - 329 ER - TY - JOUR A1 - Zink, Markus H. A1 - Küchler, Andreas A1 - Berger, Frank T1 - Kompensation des Temperatureinflusses auf dielektrische Messungen im Zeitbereich zur Beschreibung von Isolierwerkstoffen JF - ETG-Fachtagung „Grenzflächen in elektrischen Isoliersystemen“ Y1 - 2013 CY - Dresden ER - TY - BOOK A1 - Zink, Markus H. T1 - Kerntechnik Y1 - 2011 UR - http://permalink.bibkatalog.de/BV039571799 PB - Vogel Fachbuchverlag ER - TY - BOOK A1 - Zink, Markus H. T1 - Kerntechnik Y1 - 2009 UR - http://permalink.bibkatalog.de/BV023748515 PB - Vogel Fachbuchverlag ER - TY - CHAP A1 - Wirth, Isabell A1 - Sturm, Sebastian A1 - Küchler, Andreas A1 - Zink, Markus H. A1 - Berger, Frank A1 - Schnitzler, Tim T1 - Berücksichtigung von Leitungs- und Polarisationsmechanismen in transienten FEM-Simulationen von HGÜ-Isoliersystemen T2 - VDE-Hochspannungstechnik 2018, Berlin N2 - The calculation of electrical field distributions in insulation systems for high voltage direct current (HVDC) transmission using the finite element method (FEM) usually only considers the dielectric properties in the form of permittivities and conductivities. Due to not sufficiently well simulated transient processes, state of the art is considering the polarization processes by equivalent network models. The application and implementation of polarization mechanisms in a FEM soft- ware closes this gap and allows calculating the electric field distribution more precisely. An implementation of additional differential equations, according to the RC-network model, describing the field dependent polarization mechanisms, are complementing the displacement and conduction current. Material equations and their parameters are determined by measuring the polarization and depolarization currents (PDC). These equations are necessary for both the RC-network models and the differential equations for the FEM. They can be adapted to the actual temperatures in the insulation system. Hence, the necessarily multidimensional electric field calculations of complex insulation systems with stationary or transient temperature-gradients are possible. The described calculation method is verified by reactionless fieldmill voltmeter measurements of transient voltage profiles at the grading foils of modified high voltage DC-bushings. A better accuracy is achieved for the simulation of transient and stationary potential distributions. N2 - Bei der Berechnung elektrischer Feldverteilungen in Isoliersystemen für die Hochspannungsgleichstromübertragung (HGÜ) mit Hilfe der Finiten Elemente Methode (FEM) werden die dielektrischen Eigenschaften bisher meist in Form von Permittivitäten und Leitfähigkeiten berücksichtigt. Da die transienten Verläufe nicht ausreichend genau abgebildet werden, ist Stand der Technik die Polarisationsvorgänge exakter durch Netzwerkmodelle nachzubilden. Durch Implementierung von Polarisationsmechanismen in einem FEM-Programm wurde diese Lücke geschlossen und es können nun elektrische Feldverteilungen vor allem im transienten Zustand wesentlich präziser berechnet werden. In Analogie zum RC-Netzwerkmodell werden hierfür zusätzlich zu den Gleichungen, die die feldabhängigen Verschiebungs- und Leitungsströme beschreiben, weitere Differentialgleichungen eingesetzt, welche die ebenfalls feldabhängigen Polarisationsströme abbilden. Die Materialfunktionen und ihre Parameter werden durch Messung von Polarisations- und Depolarisationsströmen (PDC) ermittelt. Diese Gleichungen werden sowohl für die RC-Netzwerkmodelle als auch für die Aufstellung der Differentialgleichungen für die FEM benötigt. Sie können unmittelbar auf die am jeweiligen Ort im Isoliersystem herrschende Temperatur umgerechnet werden. Somit sind transiente elektrische Feldberechnungen auch für komplexe Isoliersysteme möglich, die sich nur durch mehrdimensionale FEM-Modelle abbilden lassen und in denen oftmals stationäre oder transiente Temperaturgradienten vorliegen. Das beschriebene Berechnungsverfahren wird durch die rückwirkungsfreie Messung transienter Potentialverläufe an den Steuerbelägen von entsprechend modifizierten kondensatorgesteuerten Hochspannungsdurchführungen verifiziert. Dabei kann eine höhere Übereinstimmung der transienten und stationären Potentialverläufe zwischen Simulation und Messung erzielt werden. Y1 - 2018 UR - https://ieeexplore.ieee.org/stamp/stamp.jsp?arnumber=8576769 ER - TY - CHAP A1 - Koch, Myriam A1 - Hohloch, Jens A1 - Wirth, Isabell A1 - Sturm, Sebastian A1 - Zink, Markus H. A1 - Küchler, Andreas T1 - Experimental and simulative analysis of the thermal behavior of high voltage cable joints T2 - VDE-Hochspannungstechnik 2018, Berlin N2 - Nowadays, cable systems are often preferred when deciding on the type of new transmission lines even in the high and extra high voltage range. One of the main reasons is the better public acceptance. In addition, the power to be transmitted in the grid is increasing leading to increased ohmic losses and thus, to higher thermal stress on the materials. The investigations in this contribution focus on cable joints, which represent important and decisive components of cable systems. In order to optimize the design and to ensure reliable operation over the entire service life, the temperature profile within these components is of special interest. For their detailed investigation, a test circuit was set up consisting of a cable section and sections with build-up stages of a cable joint. A large number of measuring points were defined also at points where no measurement is possible in normal operation. With a thermographic camera the surface temperature distributions were observed. With the laboratory setup temperature profiles under various load conditions were recorded. A detailed FEM model was built and verified with help of these measurements. The model permits the investigation of specific questions of cable systems such as the comparison of temperature loads resulting from normal operating conditions and of test procedures according to the relevant standards. Besides others the effect of stressing the insulation and sealing system by heating the inner conductor vs. heating from outside by surrounding water is discussed. Y1 - 2018 UR - https://ieeexplore.ieee.org/document/8576752 ER - TY - CHAP A1 - Wirth, Isabell A1 - Reumann, Andreas A1 - Küchler, Andreas A1 - Zink, Markus H. A1 - Berger, Frank A1 - Langens, Achim A1 - Schnitzler, Tim A1 - Heil, B. T1 - Measurement and simulation of transient field stresses and impacts on advanced insulation design and new test procedures for HVDC components T2 - Cigre-Konferenz, Paris Y1 - 2020 ER - TY - JOUR A1 - Zink, Markus H. A1 - Klipfel, V. A1 - Berger, Frank A1 - Küchler, Andreas A1 - Voll, S. T1 - Der Einfluss von Temperatur und Streukapazität auf diagnostische Kapazitäts- und Verlustfaktormessungen von 400 kV-Hochspannungstransformatordurchführungen JF - ETG-Fachtagung „Diagnostik elektrischer Betriebsmittel“ Y1 - 2012 CY - Fulda ER - TY - CHAP A1 - Wirth, Isabell A1 - Heßdörfer, Nadja A1 - Küchler, Andreas A1 - Zink, Markus H. A1 - Langens, Achim A1 - Berger, Frank T1 - Measurements and calculations of critical thermal and electrical stress conditions for HVDC bushings T2 - 20th International Symposium on High Voltage Engineering, Buenos Aires, 2017 Y1 - 2017 ER - TY - CHAP A1 - Hopf, K. A1 - Wirth, Isabell A1 - Sturm, Sebastian A1 - Küchler, Andreas A1 - Zink, Markus H. A1 - Langens, Achim T1 - Temperature-dependent and anisotropic electrical conductivity of resin-impregnated paper T2 - Power and Energy Student Summit, Nürnberg, 2017 Y1 - 2017 ER - TY - CHAP A1 - Wirth, Isabell A1 - Küchler, Andreas A1 - Zink, Markus H. A1 - Berger, Frank A1 - Langens, Achim T1 - Elektrische Feldverteilung und Polarisationsströme in HGÜ Durchführungen T2 - Fachtagung Polymere Isolierstoffe und ihre Grenzflächen, Zittau, 2018 Y1 - 2018 ER - TY - JOUR A1 - Wehnert, Kira-Kristin A1 - Ochs, Dennis A1 - Schmitt, Jan A1 - Hartmann, Jürgen A1 - Schiffler, Andreas T1 - Reducing Lifecycle Costs due to Profile Scanning of the Powder Bed in Metal Printing JF - Procedia CIRP 98 N2 - First time right is one major goal in powder based 3D metal printing. Reaching this goal is driven by reducing life cycle costs for quality measures, to minimize scrap rate and to increase productivity under optimal resource efficiency. Therefore, monitoring the state of the powder bed for each printed layer is state of the art in selective laser melting. In the most modern approaches the quality monitoring is done by computer vision systems working with an interference on trained neural networks with images taken after exposure and after recoating. There are two drawbacks of this monitoring method: First, the sensor signals - the image of the powder bed - give no direct height information. Second, the application of this method needs to be trained and labeled with reference images for several cases. The novel approach presented in this paper uses a laser line scanner attached to the recoating machine. With this new concept, a direct threshold measure can be applied during the recoating process to detect deviations in height level without prior knowledge. The evaluation can be done online during recoating and feedback to the controller to monitor each individual layer. Hence, in case of deviations the location in the printing plane is an inherent measurement and will be used to decide which severity of error is reported. The signal is used to control the process, either by starting the recoating process again or stopping the printing process. With this approach, the sources of error for each layer can be evaluated with deep information to evaluate the cause of the error. This allows a reduction of failure in the future, which saves material costs, reduces running time of the machine life cycle phase in serial production and results in less rework for manufactured parts. Also a shorter throughput time per print job results, which means that the employee can spent more time to other print jobs and making efficient use of the employee’s work force. In summary, this novel approach will not only reduce material costs but also operating costs and thus optimize the entire life cycle cost structure. The paper presents a first feasibility and application of the described approach for test workpieces in comparison to conventional monitoring systems on an EOS M290 machine. Y1 - 2021 UR - 10.1016/j.procir.2021.01.175 VL - 98 SP - 684 EP - 689 PB - Elsevir ER - TY - JOUR A1 - Hay, Bruno A1 - Beaumont, Oliver A1 - Lambeng, Nora A1 - Cataldi, Michel A1 - Lorrette, Christophe A1 - Knopp, Kevin A1 - Hartmann, Jürgen A1 - Beckstein, Fabia A1 - Stobitzer, Dorothea A1 - Milošević, Nenad A1 - Stepanic, Nenad A1 - Wu, Jiyu A1 - Mildeova, Petra T1 - Inter‑laboratory Comparison on Thermal Diffusivity Measurements by the Laser Flash Method at Ultra‑high Temperature JF - International Journal of Thermophysics N2 - thermal diffusivity measurements by the laser flash method in the temperature range from 23 °C to 3000 °C. The main objective was to assess the variability and coherency of thermal diffusivity measurements performed at ultra-high temperatures at the European level. Three refractory materials (molybdenum, tungsten and isotropic graphite IG210) were selected for this inter-laboratory comparison, due to their high melting point. The disk-shaped specimens needed were machined from the same blocks of materials in order to reduce any potential scattering of results between participants due to inhomogeneity effects. The homogeneity of the sets of specimens was studied by the pilot laboratory (LNE) before launching the comparison process. Thermal diffusivity measurements were then carried out by the seven participants on the three materials during two successive thermal cycles up to the maximum temperatures that can be reached by the devices used. The analysis of results showed a good agreement between the participants for temperatures above 400 °C, with relative deviations within the uncertainties of measurement and lower than ± 4 % for molybdenum, ± 5 % for isotropic graphite and ± 9 % for tungsten. Y1 - 2023 UR - https://doi.org/10.1007/s10765-023-03159-5 VL - 2023 SP - 44 EP - 48 ER - TY - JOUR A1 - Ackva, Ansgar A1 - Dreßel, Bernd A1 - Endres, Julian T1 - Umrichter in Hybridstruktur als Entwicklungswerkzeug und Prüfsystem für elektrische Antriebe JF - FHWS Science Journal N2 - Die Entwicklung, Applikation und der Test von Wechselrichtern, insbesondere für Traktionsantriebe, ist mit einem hohen Aufwand für die Bereitstellung einer passenden Testumgebung verbunden. Für gewöhnlich werden diese Tests in der Entwicklung als auch in der Fertigung mit Hilfe von Motor-Generator Prüfständen durchgeführt, die wiederum für unterschiedliche Leistungsklassen vorgehalten werden müssen. In diesem Beitrag wird eine neuartige hochdynamische Umrichtertopologie vorgestellt, die als universelles Entwicklungs-, Applikations- und Prüfsystem für Umrichter eingesetzt werden kann. Derzeit wird dieser Umrichter in Hybridstruktur im Rahmen eines Forschungsprojektes an der FHWS realisiert. KW - Electromobility KW - Energy Engineering Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:863-opus-484 VL - 1 IS - 2 SP - 25 EP - 36 CY - Würzburg ER - TY - JOUR A1 - Dastager, Lida A1 - Weith, Jürgen T1 - A correlation based method for measuring and monitoring the impulse response of analog LTI systems with low realization cost JF - FHWS Science Journal N2 - This article deals with the problem of measuring the impulse response of a linear time invariant (LTI) analog network. At the beginning three known measurement principles are discussed and compared with respect to their advantages and disadvantages. It is shown that good results can only be attained at the cost of measurement expense. Subsequently a new correlation based method is presented where low complexity and high quality results have not to be a contradiction. The measurement circuit basically consists of two m-sequence generators and an analog low pass filter. The characteristics of the proposed measurement circuit are examined and explained by two examples. KW - system characteristics KW - digital measurment KW - impulse response Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:863-opus-996 VL - 2 (2014) IS - 1 SP - 22 EP - 38 ER - TY - JOUR A1 - Dastager, Lida A1 - Weith, Jürgen T1 - Ein Verfahren zur automatischen Abstimmung von Einseitenband-Empfängern JF - FHWS Science Journal N2 - Es wird ein Verfahren beschrieben, mit dessen Hilfe eine Korrektur der Demodulation von Einseitenband-Signalen (ESB-Signalen) vorgenommen werden kann. Eine solche Korrektur ist dann oft notwendig, wenn sich die Frequenzen, die zur Modulation und zur Demodulation verwendet worden sind, unterscheiden. Typischerweise tritt ein solcher Frequenzunterschied bei der Übertragung von prachsignalen auf, wenn kein festes Kanalraster zugrunde liegt. Das Korrekturverfahren basiert auf einer Analyse stimmhafter Sprachabschnitte mit dem MUSIC-Verfahren. KW - elektrische Nachrichtenübertragung KW - MUSIC-Verfahren KW - Sprachqualität KW - Super-Resolution-Analyse Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:863-opus-1046 VL - 2 (2014) IS - 1 SP - 16 EP - 21 ER - TY - JOUR A1 - Rimac-Drlje, Snježana A1 - Vlaović, Jelena A1 - Mioković, Željka T1 - Gender Issues in Engineering Education JF - Papers of 33rd International Scientific Conference "Science in Practice" N2 - Female students are a minority in most technical universities in the EU, and some efforts have been made in an attempt to increase the participation of women in engineering. The growing need for IT professionals is one of the main reasons of social interest in attracting more girls to this field. This article provides a comparison of gender-related differences, as well as approaches for improving male-to-female ratio and resolving gender-related problems in engineering education. The article also presents some results of the project "Strengthening women’s position in the labor market", funded by the EU and implemented by the Faculty of Electrical Engineering in Osijek. The main objective of the project is to increase the employability of women in the Osijek-Baranja County by motivating more female students to enroll in some of the technical studies. KW - Gender Issues KW - Engineering KW - Technical Studies KW - Gender Y1 - 2015 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:863-opus-2724 SP - 17 EP - 21 ER - TY - JOUR A1 - Zhong, Xia A1 - Amrehn, Mario A1 - Ravikumar, Nishant A1 - Chen, Shuqing A1 - Strobel, Norbert A1 - Birkhold, Annette A1 - Kowarschik, Markus A1 - Fahrig, Rebecca A1 - Maier, Andreas T1 - Deep action learning enables robust 3D segmentation of body organs in various CT and MRI images JF - Scientific Reports Y1 - 2021 U6 - https://doi.org/10.1038/s41598-021-82370-6 VL - 11 IS - 1 ER - TY - CHAP A1 - Küchler, Andreas A1 - Schober, F. A1 - Harrer, S. A1 - Krause, Ch. A1 - Berger, Frank T1 - Einfluss von Temperatur und Ligningehalt auf die elektrische Leitfähigkeit von Pressspan als HGÜ-Isolierwerkstoff T2 - 6. RCC-Fachtagung „Werkstoffe zur Anwendung in der el. Energietechnik unter den besonderen Anforderungen der HGÜ“ Y1 - 2015 SP - 268 EP - 273 CY - Berlin ER - TY - CHAP A1 - Küchler, Andreas A1 - Schober, F. A1 - Harrer, S. A1 - Wolfinger, T. A1 - Krause, Ch. A1 - Exner, W. A1 - Berger, Frank T1 - Leitfähigkeit von Pressspan als diagnostische Kenngröße für HGÜ-Betriebsmittel BT - ETG-Fachtagung Diagnostik Elektrischer Betriebsmittel T2 - ETG-Fachbericht 144 Y1 - 2014 PB - VDE CY - Berlin ER - TY - BOOK A1 - Eckert, Ludwig T1 - Ein Beitrag zur Implementierung autonomer, intelligenter und feldbusgestützter Sensor-/Aktorsysteme im Feldbereich (CASE/SA) Y1 - 1999 SN - 3183571102 PB - VDI ER - TY - CHAP A1 - Küchler, Andreas T1 - Ausbildung und Steuerung elektrischer Felder bei Gleichspannungsbeanspruchung T2 - 6. RCC-Fachtagung „Werkstoffe zur Anwendung in der el. Energietechnik unter den besonderen Anforderungen der HGÜ“ Y1 - 2015 SP - 12 EP - 50 CY - Berlin ER - TY - CHAP A1 - Küchler, Andreas A1 - Reumann, Andreas A1 - Wirth, Isabell A1 - Langens, Achim A1 - Berger, Frank T1 - Erfassung transienter elektrischer Potentialverteilungen in thermisch hoch belasteten Gleichspannungsdurchführungen BT - ETG-Fachtagung Diagnostik Elektrischer Betriebsmittel T2 - ETG-Fachbericht 144 N2 - Mit Hilfe kapazitiver Steuerung können Durchführungen hochspannungsführende Leiter durch geerdete Wände in Gebäuden oder Geräten führen. Bei zeitveränderlichen Belastungen (Stoß-, Wechselspannungen) wird die gewünschte Potentialaufteilung durch die Kapazitäten zwischen den leitfähigen Steuerbelägen erzwungen. Bei Gleichspannung ergibt sich eine resistive Steuerung, die bei homogener Leitfähigkeit des Isolierkörpers eine prinzipiell gleichartige Potentialaufteilung ergibt. Durchführungen sind jedoch thermisch hoch belastete Betriebsmittel, in denen starke Temperaturgradienten und in ihrer Folge starke Leitfähigkeitsgradienten entstehen, die zu einer erheblichen Verschiebung der Potentialverteilung führen können [1]. Für Design und Diagnose ist das Verständnis dieser bisher nur theoretisch erfassbaren Vorgänge von großer Bedeutung. Deshalb wurden für experimentelle Untersuchungen zwei identische Durchführungskörper hergestellt, die mit Temperaturfühlern für thermische Messungen bzw. mit Anzapfungen für die Erfassung von elektrischen Potentialen ausgerüstet wurden. Die identische Beheizung beider Leiterrohre erlaubt es, eine Korrelation gemessener thermischer und elektrischer Profile und Transienten herzustellen. Für rückwirkungsfreie Messung der Gleichspannungspotentiale wurde ein Rotationsvoltmeter benutzt. Die Untersuchungen bestätigen das theoretisch erwartete thermisch-elektrische Verhalten und sie zeigen, dass erhebliche transiente und stationäre elektrische Belastungen auftreten können, die im Zusammenhang mit thermischen Transienten und Belastungen gesehen werden müssen. Sie sind beim Design in Rechnung zu stellen und sie zeigen, dass die bei dielektrischen Diagnosemessungen erfassten Materialkenngrößen wichtige Aussagen über den elektrischen Belastungszustand der Durchführung liefern können. Y1 - 2014 UR - https://www.vde-verlag.de/proceedings-de/453648016.html PB - VDE CY - Berlin ER - TY - CHAP A1 - Küchler, Andreas A1 - Hüllmandel, F. A1 - Appold, M. A1 - Liebschner, M. A1 - Krump, R. A1 - Titze, J. T1 - Diagnose von Hochspannungsdurchführungen durch PDC-Analyse BT - ETG-Fachtagung „Diagnostik elektrischer Betriebsmittel“ T2 - ETG-Fachbericht 104 Y1 - 2006 PB - VDE CY - Kassel ER - TY - CHAP A1 - Küchler, Andreas A1 - Hüllmandel, F. A1 - Böhm, K. A1 - Koch, N. T1 - Einfluss äußerer Grenzflächen auf die dielektrische Diagnose betriebsgealterter Hochspannungsdurchführungen BT - ETG-Fachtagung „Grenzflächen in elektrischen Isoliersystemen“ T2 - ETG-Fachbericht 99 Y1 - 2009 PB - VDE CY - Hanau ER - TY - CHAP A1 - Küchler, Andreas A1 - Zink, M. A1 - Berger, Frank T1 - Kompensation des Temperatureinflusses auf dielektrische Messungen im Zeitbereich zur Beschreibung von Isolierwerkstoffen BT - ETG-Fachtragung „Grenzflächen in elektrischen Isoliersystemen“ T2 - ETG-Fachbericht 140 Y1 - 2013 PB - VDE CY - Dresden ER - TY - CHAP A1 - Küchler, Andreas A1 - Hüllmandel, F. A1 - Böhm, K. A1 - Liebschner, M. A1 - Appold, M. A1 - Krump, R. A1 - Titze, J. T1 - Dielectric Diagnosis and Monitoring of High Voltage Bushings BT - Kolloquium T2 - 51. IWK Int. Wissenschaft Y1 - 2006 PB - Technische Universität Ilmenau CY - Ilmenau ER - TY - CHAP A1 - Küchler, Andreas A1 - Elliott, F.E. A1 - Lavier, B. A1 - Kühn, W. T1 - FEM-Study on converter transformer failures in the Celilo HVDC converter station T2 - IEEE PES winter power meeting Y1 - 1999 CY - USA ER - TY - CHAP A1 - Küchler, Andreas A1 - Krump, R. A1 - Haberecht, P. A1 - Titze, J. A1 - Liebschner, M. T1 - Bushings for Highest Voltages BT - Development, Testing, Diagnostics and Monitoring T2 - Highvolt-Kolloquium Y1 - 2007 CY - Dresden ER - TY - CHAP A1 - Küchler, Andreas A1 - Dunz, Th. A1 - Hinderer, A. A1 - Schwab, A. T1 - Transient Field Distribution Measurments with Electrically Long Sensors T2 - 5th ISH Int. Symp. on High Voltage Engineering Y1 - 1987 SP - 08 EP - 32 CY - Braunschweig ER - TY - JOUR A1 - Kaupp, Tobias T1 - Lehre, Forschung und Transfer am Beispiel der Robotik BT - vom RoboCup@Work zur autonomen Warenkommissionierung JF - FHWS Science Journal N2 - Das IDEE ist mit vier Forschungsprofessoren besetzt, die durch eine Lehrentlastung Freiräume für den Auf- und Ausbau von interdisziplinären Forschungsaktivitäten nutzen können. Das Center Robotik (CERI) ist eines der Aufgabengebiete des IDEEs mit den beiden Schwerpunkten »Robotergestützte Arbeitsplätze der Zukunft« sowie »Intralogistik in der Smart Factory«. Dieser Artikel beschäftigt sich mit dem zweiten Schwerpunkt. Anhand der CERI Aktivitäten im Bereich der fahrerlosen Transportsysteme wird aufgezeigt, wie der »Dreiklang« Forschung, Lehre und Transfer in der Praxis umgesetzt wird und die drei Bestandteile sich gegenseitig befruchten können. KW - robotik Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:863-opus-20065 UR - https://nbn-resolving.org/urn:nbn:de:bvb:863-opus-19389 SN - 2196-6095 VL - 5 IS - 2 SP - 109 EP - 116 ER - TY - THES A1 - Wirth, Isabell T1 - Berücksichtigung dielektrischer Materialeigenschaften in der Finiten-Elemente-Simulation von HGÜ-Isoliersystemen T2 - Ilmenauer Beiträge zur elektrischen Energiesystem‐, Geräte- und Anlagentechnik N2 - Verbrauchsfern erzeugter Strom aus regenerativen Energien kann über große Distanzen am wirtschaftlichsten mittels der Hochspannungsgleichstromübertragung (HGÜ) transportiert werden. Die HGÜ führt zu einer veränderten elektrischen Belastung der Hochspannungskomponenten. Transiente Übergangsvorgänge bestimmen die elektrischen Feldverteilungen. Bei der Berechnung elektrischer Feldverteilungen in Isoliersystemen für die Hochspannungsgleichstromübertragung (HGÜ) mit Hilfe der Finiten-Elemente-Methode (FEM) wurden die dielektrischen Eigenschaften bisher in Form von Permittivitäten und parameterabhängigen Leitfähigkeiten berücksichtigt. Langsame Polarisationsvorgänge werden dabei nicht berücksichtigt. Für die Berechnung komplexer Isoliersysteme durch die FEM ist deshalb die Beschreibung der langsamen Polarisationsvorgänge im Isolierstoff durch Differentialgleichungen wünschenswert, die direkt in die FEM einbezogen werden und mit denen je nach Bedarf sowohl einzelne Polarisationsmechanismen als auch ihre Überlagerungen berücksichtigt werden können. In dieser Arbeit werden hierfür auf Basis des bekannten Debye-Ansatzes, und in Analogie zum Netzwerkmodell, zusätzlich zu den Gleichungen, die Verschiebungs- und Leitungsströme beschreiben, weitere Differentialgleichungen direkt in die FEM einbezogen, welche die feld- und temperaturabhängigen Polarisationsströme individuell abbilden. Die Materialfunktionen und ihre Parameter werden durch Messung von Polarisations- und Depolarisationsströmen (PDC) ermittelt. Durch die Implementierung von beliebigen Polarisationsmechanismen in einem FEM-Programm wurde eine Lücke der Berechnungsmöglichkeiten von komplexen, auch dreidimensionalen Isoliersystemen geschlossen, in denen oftmals stationäre oder transiente Temperaturgradienten vorliegen und in denen sich transiente elektrische Feldverteilungen ausbilden. Zur Verifizierung des beschriebenen Berechnungsverfahrens werden transiente Potentialverläufe an den Steuerbelägen von entsprechend modifizierten Hochspannungsdurchführungen unter Gleich- und Umpolspannungen sowie unter thermischen Gradienten gemessen. Dabei kann eine bisher nicht erreichte Übereinstimmung der transienten und stationären Potentialverläufe zwischen FEM-Simulation und Messung erzielt werden. Auswirkungen auf Prüf- und Belastungsszenarien werden anhand von Simulationen diskutiert. N2 - Consumer-remotely generated electricity from renewable energies can be transported over long distances most economically by means of high-voltage direct current (HVDC) transmission. The HVDC leads to a change in the electrical stress on the high-voltage components. Transient processes determine the electric field distributions. Calculations of electrical field distributions in insulation systems for high-voltage direct current (HVDC) transmission using the finite element method (FEM) by default consider the dielectric properties in the form of permittivities and parameter-dependent conductivities. Thereby, slow polarisation processes are not considered. For FEM calculation of complex insulation systems, a description of slow polarisation processes in insulating materials is therefore desirable. Differential equations should be directly implemented into the FEM in order to consider individual polarisation processes as well as their superposition, according to demand. In this work, differential equations based on the well-known Debye approach, and in analogy with the equivalent-circuit model, are directly implemented into the FEM. Thereby, field-dependent and temperature-dependent polarisation currents are represented individually and additionally to the equations describing displacement currents and conduction currents. Material functions and their parameters are determined by measuring the polarisation and depolarisation currents (PDC). The implementation of any desired polarisation mechanisms in a FEM program has closed a gap in the computational possibilities of complex and even three-dimensional insulation systems, which often have stationary or transient temperature gradients and which show transient electrical field distributions. For the verification of the described calculation method, measurements of transient voltage profiles were made at the grading layers of modified high voltage bushings being stressed with DC voltage, polarity reversals and being subject to thermal gradients. It is shown that a previously unattainable agreement of the transient and stationary potential profiles between FEM simulation and measurement can be achieved. Effects on test and load scenarios are discussed based on simulation results. KW - Hochspannungsgleichstromübertragung KW - Isolierstoff KW - Dielektrische Eigenschaft KW - Finite-Elemente-Methode Y1 - 2020 UR - https://nbn-resolving.org/urn:nbn:de:gbv:ilm1-2019000601 SN - 978-3-86360-215-4 U6 - https://doi.org/10.22032/dbt.41185 IS - 26 PB - Universitätsverlag Ilmenau CY - Ilmenau ER - TY - THES A1 - Zimmermann, Korbinian T1 - Verwaltung von Trainingsdaten für Künstliche Intelligenz N2 - In order to operate a permanent magnet synchronous motor (PSM) as efficiently as possible, it requires precise information about the current thermal state of the electric drive. In most production vehicles, rotor and stator thermocouples are not used for financial reasons. Within the development of a temperature model based on the physical approach, measurements are carried out with a telemetry unit installed in the electric motor. These take place both on the test bench and in the test vehicle. The resulting measurement records give reason to investigate a data-based approach using deep learning, which is the aim of this work. In addition to the evaluation of the existing test bench and vehicle data, the focus is on the development of a neural temperature model. The results obtained will be compared with the existing ECU temperature model. Y1 - 2022 EP - 92 ER -