Refine
Document Type
Has Fulltext
- yes (3)
Is part of the Bibliography
- no (3)
Language
- English (3)
Keywords
- Beschichtung (1)
- Biomedical applications (1)
- Biomedizin (1)
- Biomedizinische Anwendungen (1)
- Characterization (1)
- Charakterisierung (1)
- DIN 1.2367 (1)
- Fotokatalyse (1)
- Mehrschichtsystem (1)
- Multilagenbeschichtung CAZO/CZAO/ZACO (1)
- Multilayer CAZO/CZAO/ZACO (1)
- Nanobiomaterials (1)
- Nanocomposites (1)
- Nanokomposit (1)
- Nanokompositen (1)
- Nanostructures (1)
- Nanostrukturen (1)
- Nanostrukturiertes Material (1)
- Nanowerkstoffe (1)
- Nitrierhärten (1)
- PVD coating (1)
- PVD-Beschichtung (1)
- Photocatalysis (1)
- Photodetector (1)
- Photodetektor (1)
- Photokatalyse (1)
- Ringer's solution (1)
- Ringerlösung (1)
- Rotationsbeschichtung (1)
- Ti-Nb-Zr alloys (1)
- Ti-Nb-Zr-Legierungen (1)
- Titanlegierung (1)
- Tribological behavior (1)
- Tribologie (1)
- Tribologisches Verhalten (1)
- Verschleiß (1)
- Warmarbeitsstahl (1)
- Wear (1)
- Werkzeugprüfung (1)
- Werkzeugstahl (1)
- Zirconium (1)
Institute
Morphological and optical properties of a multilayer film (CAZO/CZAO/ZACO) prepared by spin-coating method and deposited on a glass substrate were evaluated. The study was initially carried out for each layer, individually and then as a multilayer subsequently. Structural properties using X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), infrared spectra (IR) and X-ray photoelectron Spectroscopy (XPS) showed the presence of three phases of zinc, copper and silver oxides at different levels. The CZAO sample observed with scanning electron microscope (SEM) showed an excellent porous surface with a large deformation in the multilayer configuration. Doping with zinc and copper in the silver crystal lattice improved the crystal structure and reduced the optical energy gap, thus increasing the optical absorbance and refractive index. The dielectric constants and showed an increase in the optical polarization values for lower photonic energies. The maximum degradation rate for photocatalysts of methylene blue was 89 % for a 5-h exposure period with CAZO/CZAO/ZACO while it reached 71 % for the CZAO sample during the same time period. The sensitivity of samples to light proved that the presence of ultraviolet radiation increases the number of holes trapped by oxygen ions and causes more free electrons and contribute to a better production of photocurrent than in darkness.
In order to create alloys with exceptional properties for orthopedic uses, this study focuses on the impact of zirconium (Zr) content on the structural, electrochemical, and tribological qualities of nanostructured Ti–25NbxZr [x = 5, 10, 15, 20, 25, and 30 atomic (at.) %] alloys. The structural evolution was investigated using XRD and SEM techniques. The mechanical characteristics of the produced alloys, including Vickers hardness and Young’s modulus, were measured. In addition, the corrosion tests were performed using the OCP, EIS, and PD methods in Ringer’s solution within the independent pH range at 37°C. A ball-on-disc tribometer was used to investigate the tribological behavior of the alloys under various loads and wet conditions using the Ringer solution. It has been verified that Zr content (at. %) in the alloys had an impact on their morphologies, structural evolution, and mechanical characteristics. According to the morphological analysis, the particle and crystallite size decreases with increasing Zr content. Young’s modulus and Vickers hardness show the same tendency. The EIS data demonstrated that a single passive film formed on the alloy surfaces, and the addition of Zr enhanced the corrosion resistance of the passive films. The polarization curves demonstrate that the alloys had low corrosion current densities and large passive areas without the passive films disintegrating. Likewise, the inclusion of Zr resulted in a reduction in the corrosion and passive current density values. All of these results suggested that the titanium alloys exhibit a more noble electrochemical activity caused by Zr. From the tribological perspective, it was found that the friction coefficient of the alloys reduced with increasing Zr content.
In this study, heat-treated and multisurface engineered DIN 1.2367 tool steel was subjected to room and elevated temperature wear tests, and the effect of nitriding on its tribological behavior was investigated. CrN, AlTiN, and CrN/AlTiN coatings with a total thickness of 2 µm were obtained by arc cathodic physical vapor deposition on conventional heat-treated and gas-nitrided steels. The white layer formed during nitriding was removed, and a diffusion layer (100 µm) was achieved in the cross section of the steel having a tempered martensitic matrix. The highest surface hardness was attained with an integral coating (CrN/AlTiN), and surface hardness increased even more after nitriding due to the formation of a multicomponent ceramic layer on top of the diffusion layer. The room temperature wear tests performed against an alumina counterpart revealed that (i) CrN/AlTiN-coated steel had the highest friction coefficient of 0.26, which further increased to 0.33 by nitriding due to the increase in shear strength, and that (ii) with increasing surface hardness, the specific wear rates (W) of the heat-treated and coated steels could be ranked as follows: WCrN/AlTiN < WAlTiN < WCrN. The wear rates decreased when nitriding was carried out prior to coating. In order to simulate the aluminum extrusion conditions, hot wear behavior of the surfaces against AA6080 alloy at 450 °C was investigated. The hot wear tests revealed that (i) high friction coefficients were reached due to the adhesive characteristic of aluminum to the surfaces, (ii) the nitrided and CrN/AlTiN-coated sample exhibited the lowest wear rate among all studied surfaces, and (iii) the film damage on the worn surfaces mostly occurred in the form of droplet delamination.