Filtern
Dokumenttyp
- Zeitschriftenartikel (11) (entfernen)
Referierte Publikation
- nein (11) (entfernen)
Schlagworte
- Verbundwerkstoffe (6)
- Interface (4)
- Thermoplaste (4)
- Adhäsion (3)
- Haftung (3)
- Reibung (3)
- Biegeschwingung (2)
- Ermüdung (2)
- Glasfaser (2)
- Thermoplast (2)
Organisationseinheit der BAM
Pull-out of Single Fibres
(1994)
Fatigue Behaviour of High-Performance Fibre-Reinforced Composites with a Thermoplastic Matrix
(1990)
An advanced equipment for single-fibre pull-out test designed to monitor the fracture process
(1995)
Viscoelastic properties of the interphase in fibre reinforced polymers - measurement and simulation
(1999)
Investigations on the cold crystallization of pure and filled PETP by dielectric measurements
(1993)
The cold crystallization of pure and filled poly(ethylene terephthalate) (PETP) after quenching from the melt has been investigated by dielectric measurements in two different modes: The first one using constant heating-rate (in the temperature range from 320 to 480 K) and the second one under isothermal conditions (at 378 K). The complex dielectric constant (ε´, tan δ) is influenced by crystallization. Two α-relaxation regions are identified: The αa-relaxation region from the pure amorphous phase and the α´-relaxation region from the spherulitic phase. The investigations on the filled systems (PETP + 10% aramid puple, PETP + 30% short glass fibres) prove that an influence of the fillers on the time delay and rate of crystallization and on the geometry of the growing spherulites exists.
A fiber Bragg grating (FBG) strain patch specially adapted for long-term and high-strain applications has been developed and characterized. The design concept for the patch is based on a glass-fiber reinforced plastic (gfrp) carrier material. The developed concept for the FBG integration into the carrier material was derived from reliable integration procedure of FBG sensors into composite structures. The patches' temperature sensitivity, strain gauge factor, fiber–matrix interface adhesion and fatigue behavior were characterized. As a result, FBG strain patches with linear temperature and strain behavior, as well as excellent fatigue resistance, were developed and can be used as part of a monitoring system for advanced composite materials in aerospace structures or wind turbine power plants.
Effects of various geometrical and physical factors, as well as the method of data reduction (analysis of
experimental forceedisplacement curves) on the values of local interfacial strength parameters (local IFSS, td, and critical energy release rate, Gic) determined by means of a single fiber pull-out test are discussed. Experimental results of our pull-out tests on several fiberepolymer matrix systems showed that td and Gic weakly depended on geometrical factors. However, the pull-out test appeared to be sensitive to the conditions of specimen formation and testing, such as changing the nature of the contacting surfaces (fiber sizing) and the fiber pull-out rate. Of several methods of td and Gic Determination from a forceedisplacement curve, the most reliable and reproducible one is the approach based on the values of the maximum force recorded in a pull-out test and the interfacial frictional force immediately after fiber debonding.
Tooth wear induced by abrasive particles is a key process affecting dental function and life expectancy in mammals. Abrasive particles may be plant endogenous opal phytoliths, exogene wind-blown quartz dust or rain borne mineral particles ingested by mammals. Nano-indentation hardness of abrasive particles and dental tissues is a significant yet not fully established parameter of this tribological system. We provide consistent nano-indentation hardness data for some of the major antagonists in the dental tribosystem (tooth enamel, tooth dentine and opaline phytoliths from silica controlled cultivation). All indentation data were gathered from native tissues under stable and controlled conditions and thus maximize comparability to natural systems. Here we show that native (hydrated) wild boar enamel exceeds any hardness measures known for dry herbivore tooth enamel by at least 3 GPa. The native tooth enamel is not necessarily softer then environmental quartz grit, although there is little overlap. The native hardness of the tooth enamel exceeds that of any silica phytolith hardness recently published. Further, we find that native reed phytoliths equal native suine dentine in hardness, but does not exceed native suine enamel. We also find that native suine enamel is significantly harder than dry enamel and dry phytoliths are harder than native phytoliths. Our data challenge the claim that the culprit of tooth wear may be the food we chew, but suggest instead that wear may relates more to exogenous than endogenous abrasives.