Filtern
Erscheinungsjahr
- 2013 (31) (entfernen)
Dokumenttyp
Sprache
- Englisch (19)
- Deutsch (11)
- Mehrsprachig (1)
Schlagworte
- Cadmium (2)
- Ionic conductivity (2)
- Mechanical properties (2)
- Multifunctional supercapacitor (2)
- Structural electrolyte (2)
- AES (1)
- Additive manufacturing (1)
- Adiabatische Lagerprüfung (1)
- Aerosole (1)
- Alkali silica reaction (1)
Ziel des Projekts „Überprüfung der Quecksilber-, Cadmium- und Blei-Gehalte in Batterien. Analyse von Proben handelsüblicher Batterien und in Geräten verkaufter Batterien. Erstellung eines Probenahmeplans, Probenbeschaffung und Analytik“ war es, über eine gut ausgewählte Stichprobe eine qualitative Situationsbeschreibung bezüglich der potenziellen Belastung des Hausmülls und der Batterie-Verwertungsverfahren durch schwermetallhaltige Batterien zu erhalten. In diesem Zusammenhang wurden die ermittelten Schwermetallgehalte der Batterien mit den Grenzwerten und Kennzeichnungsschwellenwerten des BattG verglichen.
Tapes, cast by blade deposition of a lithium aluminosilicate glass slurry, were sintered using a YAG-fiber laser, with the aim of finding suitable parameters for an additive manufacturing process based on layer-wise slurry deposition and selective laser densification. The influence of the laser parameters (output power and scan velocity) on the sintering was evaluated, by scanning electron microscopy and by X-ray diffraction, on the basis of the quality of the processed layer. Well densified samples could be obtained only in a small window of values for the output power and the scan velocity. The measurement of the width of a set of single scanned lines allowed also to estimate the minimum resolution of the system along the layer plane.
Highly porous (>60% open porosity) glass–ceramic scaffolds with remarkable mechanical properties (compression strength of ~15 MPa) were produced by indirect 3D printing. Precursor glass powders were printed into 3D ordered structures and then heat treated to sinter and develop crystalline phases. The final glass–ceramic contained a β-spodumene solid solution together with a secondary phase of lithium disilicate.
The precision of the printed geometry and the density of the struts in the scaffold depended on several processing parameters (e.g. powder size and flowability, layer thickness) and were improved by increasing the binder saturation and drying time. Two types of powders with different particle size distribution (PSD) and flowability were used. Powders with a larger PSD, could be processed within a wider range of printing parameters due to their good flowability; however, the printing precision and the struts density were lower compared to the scaffolds printed using the powder in a smaller average PSD.
The effects of single femtosecond laser pulse irradiation (130 fs pulse duration, 800 nm center wavelength) on the structure of binary lithium silicate glasses of varying chemical compositions were investigated by micro-Raman spectroscopy. Permanent modifications were generated at the surface of the glass samples with varying laser fluences in the ablative regime and evaluated for changes in the corresponding Raman band positions and bandwidths. For increasing laser fluences, the position of certain Raman bands changed, indicating an increase in the mass density of the glass inside the irradiated area. Simultaneously, the widths of all investigated bands increased, indicating a higher degree of disorder in the glass structure with respect to bond-angle and bond-length variations.
Electrolyte systems that can carry mechanical load while allowing for high levels of ionic conductivity are an important prerequisite for structural power storage devices. Introduction of structural power storage into the variety of consumer products will allow saving in weight and volume. Moreover, using a supercapacitor/battery system in hybrid electric vehicles (HEV), the supercapacitor part will extend the battery lifetime by protecting it from the high peak currents. To successfully produce structural power storage requires the development
of multifunctional electrolytes where one has to simultaneously maximize mechanical properties and ionic conductivity.
Die "Empfehlungen für die Beförderung gefährlicher Güter, Handbuch über Prüfungen und Kriterien" ergänzen die "Empfehlungen für die Beförderung gefährlicher Güter, Modellvorschriften" und das "Global harmonisierte System zur Einstufung und Kennzeichnung von Chemikalien (GHS)". Sie enthalten Kriterien, Prüfmethoden und –verfahren, die angewendet werden sowohl für die Einstufung gefährlicher Güter nach den Vorschriften der Teile 2 und 3 der Modellvorschriften als auch für Chemikalien, von denen nach dem GHS physikalische Gefahren ausgehen.