Filtern
Erscheinungsjahr
- 2015 (2295) (entfernen)
Dokumenttyp
- Vortrag (1030)
- Zeitschriftenartikel (463)
- Posterpräsentation (398)
- Beitrag zu einem Tagungsband (301)
- Forschungsbericht (26)
- Dissertation (19)
- Beitrag zu einem Sammelband (18)
- Buchkapitel (15)
- Sonstiges (13)
- Zeitschriftenheft (Herausgeberschaft für das komplette Heft) (5)
Sprache
- Deutsch (1566)
- Englisch (722)
- Mehrsprachig (6)
- Französisch (1)
Schlagworte
- Concrete (17)
- Corrosion (17)
- Monitoring (15)
- Non-destructive testing (13)
- Nanoparticles (11)
- Simulation (11)
- Prozessanalytik (10)
- Zerstörungsfreie Prüfung (10)
- Fluorescence (9)
- Ultrasound (9)
Eingeladener Vortrag
- nein (1030)
Fukuda et al. published a paper (Scripta Mater. 68 (2013) 984–987) in which they claimed to be able to determine the isothermal nature of the martensitic transformation in a Ti–Ni alloy. They analyzed the evolution of electrical resistance during isothermal holding stages and concluded that the variations were a consequence of the isothermal transition between austenite and martensite. In the following we will demonstrate that the discussed data do not allow the interpretation presented and that the isothermal nature is not proved.
Sulphurous additives for polystyrene: Influencing decomposition behavior in the condensed phase
(2015)
The thermal decomposition behaviour of polystyrene (PS) containing sulphur and phosphorus additives was investigated, using thermogravimetry coupled with Fourier transform infrared spectroscopy (TGA-FTIR). It was found that the additives influence the decomposition process of the polymer in the condensed phase, resulting in a decrease in styrene monomer formation and an increase in styrene oligmer derivatives. Via reference measurements with binary mixtures it was found that the presence of sulphur additives influences the radicalic decomposition process of PS. In combination with quantum chemical calculations it was concluded that this is due to the formation of radicals that abstract hydrogen from the polymer matrix at lower temperatures, disfavouring the radicalic decomposition pathway leading to styrene.
The effect of structural constriction on molecular mobility is investigated by broadband dielectric spectroscopy (BDS) within three types of molecular arrangements: monomers, oligomers and self-assembled monolayers (SAMs). While disordered monomers exhibit a variety of cooperative and local relaxation processes, the constrained nanodomains of oligomers and highly ordered structure of monolayers exhibit much hindered local molecular fluctuations. Particularly, in SAMs, motions of the silane headgroups are totally prevented whereas the polar endgroups forming the monolayer canopy show only one cooperative relaxation process. This latter molecular fluctuation is, for the first time, observed independently from other overlapping dielectric signals. Numerous electrostatic interactions among those dipolar endgroups are responsible for the strong cooperativity and heterogeneity of the canopy relaxation process. Our data analyses also revealed that the bulkiness of dipolar endgroups can disrupt the organization of the monolayer canopy thus increasing their ability to fluctuate as temperature is increased.
An approach is presented to model elastic waveguides of arbitrary cross-section coupled to infinite solid media. The formulation is based on the scaled boundary-finite element method. The surrounding medium is approximately accounted for by a dashpot boundary condition derived from the acoustic impedances of the infinite medium. It is discussed under which circumstances this approximation leads to sufficiently accurate results. Computational costs are very low, since the surrounding medium does not require discretization and the number of degrees of freedom on the cross-section is significantly reduced by utilizing higher-order spectral elements.
Epoxy carbon-fibre prepreg, Hexcel Type 6376 HTS, was investigated using Dynamic Mechanical Analysis (DMA). The DMA characteristic parameters are storage modulus E', loss modulus E' and loss factor tanδ. These parameters are ideally suited to observe the vitrification, referred to as glass transition, resulting from the cross-linking reaction. Detection of the cure state may also be achieved by determining the momentary glass transition temperature of partially cured samples. The consequent use of a multi-frequency measuring regime was used to derive the apparent activation energy for the glass transition process. Different temperature programs were also applied to monitor the curing process directly, as well as to investigate the different states of incomplete cure reached in preceding curing steps. The intention was to provide better understanding of the consequences of an interrupted autoclave curing process and to use DMA to detect the cure state achieved. With DMA, the continuation of an incomplete curing process also can be monitored. DMA measurements up to 300 °C showed, furthermore, that the final glass transition temperature was reduced by thermal degradation at high temperatures.
The objects of this investigation were sculptures taken from a ca. three hundred years old baroque epitaph of a church in Tonning, a town in Northern Germany. Around 1900 it was found in a disastrous state heavily damaged by wood-worm. At that time, the whole artwork was treated with the tar extract carbolineum as a remedy. Nowadays, this substance has been identified as carcinogenic, and its presence can be perceived by its stench and visually at certain spots on the surface where it has penetrated the covering paint.
A gold-painted sculpture of a massive wooden skull was interrogated with X-rays and fast neutrons to investigate the internal distribution of the carbolineum. The X-ray tomography, with its excellent spatial resolution revealed galleries left over from the worm infestation in the outer areas and cracks in the central region. The golden color coating appeared as a thick and dense layer. In comparison the tomography with fast neutrons, though being of lower resolution and yet unresolved artefacts revealed sections of slightly different densities in the bulk of the wood. These differences we attribute to the differences in the distribution of the impregnant in the wood, visible due to its higher hydrogen content making it less transparent for neutrons.
ISO standards for gas cylinders made from aluminum alloys generally require heat treatment after the forming process. Such heat treatment is a costly part of the manufacturing process. Particularly due to increasing international trade, market-surveillance authorities need simple and reliable methods to field-test cylinders for proper heat treating. By the present contribution the difference in strength of heat-treated and non-heat-treated gas cylinders is exemplarily shown and several material analysis methods are investigated for their suitability as field tests.
This article presents an analytical approach for simulation of ultrasonic diffracted wave signals from cracks in two-dimensional geometries based on a novel Huygens–Fresnel Diffraction Model (HFDM). The model employs the frequency domain far-field displacement expressions derived by Miller and Pursey in 2D for a line source located on the free surface boundary of a semi-infinite elastic medium. At each frequency in the bandwidth of a pulsed excitation, the complex diffracted field is obtained by summation of displacements due to the unblocked virtual sources located in the section containing a vertical crack. The time-domain diffracted wave signal amplitudes in a general isotropic solid are obtained by standard Fast Fourier Transform (FFT) procedures. The wedge based finite aperture transducer refracted beam profiles were modelled by treating the finite dimension transducer as an array of line sources. The proposed model is able to evaluate back-wall signal amplitude and lateral wave signal amplitude, quantitatively. The model predicted range-dependent diffracted amplitudes from the edge of a bottom surface-breaking crack in the isotropic steel specimen were compared with Geometrical Theory of Diffraction (GTD) results. The good agreement confirms the validity of the HFDM method. The simulated ultrasonic time-of-flight diffraction (TOFD) A-scan signals for surface-breaking crack lengths 2 mm and 4 mm in a 10 mm thick aluminium specimen were compared quantitatively with the experimental results. Finally, important applications of HFDM method to the ultrasonic quantitative non-destructive evaluation are discussed.
A software prototype is developed for assessing and updating the reliability of single-cell prestressed concrete box girders subjected to chloride-induced reinforcement corrosion. The underlying system model consists of two integrated sub-models: a condition model for predicting the deterioration state of the box girder and a structural model for evaluating the overall system reliability. The condition model is based on a dynamic Bayesian network (DBN) model which considers the spatial variation of the corrosion process. Inspection data are included in the calculation of the system reliability through Bayesian updating on the basis of the DBN model. To demonstrate the effect of partial inspections, the software prototype is applied to a case study of a typical highway bridge with six spans. The case study illustrates that it is possible to infer the condition of uninspected parts of the structure due to the spatial correlation of the corrosion process.
First developments of a new test to evaluate the fire behavior of photovoltaic modules on roofs
(2015)
A new test for photovoltaic (PV) modules exposed to an external fire source on roofs is proposed, and first results are presented. This is a simplification of the standards commonly in use for testing PV modules as roofing parts, roofing components or building components. Most of the tests required different fire scenarios and the use of burning brands such as wood cribs. In our study we proposed replacing wooden burning brands with a propane burner, the output of which is close to the one that can be observed in the burning of wooden cribs 500 g and 2 kg in size. The fire behavior was assessed by measuring smoke evolution, burning drips, flaming debris, and the time to burn-through of monocrystalline, polycrystalline and amorphous silicon panels. Two different configurations of the burner were tested, with the fire source on the top of the module or under the tilted module, respectively. The fire behavior of the modules was dependent on the burner output (16 to 46 kW), but also on the construction type of the panel (glass/glass or glass/plastic sheet) and on the position of the fire source (top or bottom). These preliminary tests for further development of the procedure yielded encouraging results for the evaluation of PV panels on roofs.
The aim of this study was the development of a low volume air sampling strategy for biocides and polychlorinated biphenyls (PCB) at low air change rates in modern, air-tight showcases as they are present in museums. Lindane, pentachlorophenol, dichlofluanid, tolyfluanid, isodrin, p,p-dichlorodiphenyl trichloroethane and permethrin were the biocides and PCB 28 and PCB 153 were the PCBs studied, all of which are semi volatile organic compounds (SVOC). Their occurrences in the museum environment originate from various sources e.g. preventive treatment of organic exhibits or organic building materials. Exhibits are long-term exposed to these pollutants due to storing in showcases or other storage equipment at low air change rates. To achieve air sampling under the aforementioned conditions the influences of temperature, air circulation, air change rate and relative humidity on the emission behavior of the selected biocides and PCBs had to be determined. This was carried out with pre-soaked wood samples in low volume air sampling experiments using 27 L test showcases and 23 L and 24 L emission test chambers and also diffusive sampling with glass as the sampling material.
The pore structure of lightweight granules made from masonry rubble was studied in order to better understand their engineering properties. Thermally and hydrothermally hardened granules were tested. Analysis by ESEM, mercury porosimetry and sorption methods yield important insight into their microstructure. The thermal granules are characterised by partly melted vitreous areas and large internal macropores that are connected via narrow throats. They show a marginal specific surface area along with a hydrophobic behaviour. In contrast, the hydrothermal granules have an accessible mesoporous system containing plate-like and ink-bottle pores. The shape of their water isotherms depending on the granules CaO content is sensitive to the morphology of calcium silicate hydrate phases (CSH). The hysteresis changes from a narrow loop that closes at low pressures, which can be attributed to coarser more crystalline CSH, to a large triangular-shaped loop along with a low pressure hysteresis, which is characteristic for fine fibre-like CSH with ink-bottle and plate-like pore morphologies. Granules with fibre-like CSH have the higher specific surfaces areas but those with more crystalline CSH show stronger physisorption of water molecules.
The aim of the joint project ViPQuali (Virtual Product Qualification) was to describe a components ageing behaviour in a given environment, by numerical simulation.
Having chosen polypropylene (PP) as the material, which does not show sensitivity to moisture, the relevant weathering parameters of the doseresponse functions could be limited to spectral irradiance and temperature.
In artificial irradiation tests, for PP plates of varied stabiliser content, spectral sensitivity as well as temperature dependence of irradiation-caused crack formation was quantified. For that purpose, samples were exposed both to artificial weathering tests at various constant temperatures and to spectrally resolved irradiation. The temperature dependence could be modelled by an Arrhenius fit. For fitting the spectral sensitivity, a plateau function was chosen. Subsequently, the stabiliser content was parameterised and extrapolated.
The formed dose–response functions were incorporated into a Computational Fluid Dynamics (CFD) software program, simulating the environment of a sample within a Phoenix-exposed IP/DP (Instrument Panel/Door Panel box) box, based on sun position and weather conditions, including radiation interactions. Observed local effects as well as the general ageing advance of PP hats are compared with respect to simulation and experiment.
Resulting from this project, for this most simple example of PP of varied stabiliser content, the time to failure can be estimated for each weathering exposure environment with known time-resolved irradiance and temperature conditions.
NbC has a relatively high hardness (19.6 GPa) and melting temperature (3600 °C) and is usually applied as a grain growth inhibitor in WC–Co hardmetals. The current study reports on the influence of the sintering technology and overall chemical composition on the microstructure and mechanical properties of NbC-based hardmetals, using Co as a binder. The partial replacement of NbC by 5 wt.% WC, Mo2C, VC or TiC allows one to significantly improve the hardness and toughness of the NbC–Co materials. The influence of different binders, i.e., Co, 316L stainless steel and Fe3Al on the microstructure and mechanical properties of NbC-based hardmetals was also investigated. The powder mixtures were sintered in the solid state by PECS and liquid state by conventional vacuum sintering. Detailed microstructural analysis was conducted by EPMA elemental mapping and WDS point analysis. Mechanical properties, including Vickers hardness and indentation toughness were assessed.