Filtern
Erscheinungsjahr
- 2008 (1562) (entfernen)
Dokumenttyp
- Vortrag (659)
- Zeitschriftenartikel (324)
- Posterpräsentation (238)
- Beitrag zu einem Sammelband (168)
- Beitrag zu einem Tagungsband (119)
- Dissertation (12)
- Forschungsbericht (10)
- Sonstiges (9)
- Buchkapitel (7)
- Zeitschriftenheft (Herausgeberschaft für das komplette Heft) (4)
- Monografie (3)
- Sammelband (Herausgeberschaft für den kompletten Band) (3)
- Tagungsband (Herausgeberschaft für den kompletten Band) (2)
- Newsletter (2)
- Jahresbericht (1)
- Handbuch (1)
Sprache
- Deutsch (1088)
- Englisch (462)
- Mehrsprachig (10)
- Französisch (1)
- Russisch (1)
Schlagworte
- Beton (12)
- Non-destructive testing (12)
- Radar (10)
- Fluorescence (9)
- Quality assurance (9)
- Concrete (8)
- Cultural heritage (8)
- NMR (8)
- DLC (7)
- Fluorescence spectroscopy (7)
Eingeladener Vortrag
- nein (659)
Die Wirksamkeit einer Abtrennung aus Holz mit mindestens 50 mm Wandstärke für Zündmittel der Klassifizierung 1.4B konnte überzeugend bestätigt werden. Außerhalb dieser Abtrennung war überhaupt keine Wirkung zu beobachten. Auch wenn die Originalverpackung leichterer Bauart vergleichsweise stark beschädigt wurde fungierte die hölzerne Abtrennung aus wirksamer Schutz gegen die entstandenen Splitter. Einer weiteren Anwendung der bisherigen Verfahrensweise steht aus sicherheitstechnischer Sicht nichts im Wege.
Tribological screening tests (simple, reciprocating ball-on-flat tests) were performed with the objective to identify an appropriate coating for the articulating surfaces of artificial hip joints whose acetabular cups and femoral stems are made from Ti6Al4V alloy, which is appreciated for its light weight, good biocompatibility and elastic properties similar to those of natural bone. Standard coatings like TiN or CrN performed better than more complicated multi-layer systems, though not as good as different types of amorphous carbon coatings, generally referred to as diamond-like carbon or DLC coatings. Among the latter, hydrogenated amorphous carbon (a-C:H) displayed the best properties, especially if the hydrogen content was increased by reducing the bias voltage during PA-CVD-deposition.
The optimised a-C:H coating revealed the most promising wear behaviour under the applied testing conditions, i.e. the increase of linear wear with the number of cycles was close to zero. Regarding the materials examined in this study, correlation of wear with mechanical properties obtained by nano-indentation revealed that high hardness was not an adequate criterion for selecting appropriate coatings. A high ratio of hardness and elastic modulus (H/E) proved to be more important. Microstructural and micro-analytical investigations revealed transformation of TiN and CrN to TiO2 and Cr2O3, respectively, and amorphous carbon was, at least partly, transformed to graphite. Furthermore, incorporation of Al2O3 from the ball was observed at a very fine scale. The wear debris of favourable coatings always formed agglomerates of nano-scale particles. It was shown that commercial nano-particles of Al2O3, Cr2O3 and carbon black are comparable to particles generated by the tribological tests. However, it is uncertain whether they are comparable to those formed during simulator studies or in vivo. Furthermore, the performance of the favourable coating has to be tested in a hip joint simulator before its potential for application in prostheses can be assessed.
Geosynthetic clay liners (GCLs) often have a sandwich-like multilayer structure, e.g. bentonite encased between two geotextile layers connected by fibers or yarns, either by needle-punching or stitch-bonding. Therefore, the internal shear strength of the GCL depends on the strength of reinforcing fiber bundles or yarns and their anchoring strength in the cover and carrier geotextiles. When used on long and steep slopes and covered with thick soil layers, the GCL is permanently exposed to a combined action of compressive and shear stress. Such load conditions are characteristic for landfill covers and the slope stability of the overall cover system in the long run strongly depends on the long-term internal shear strength of the GCL. A new test method was developed to study this long-term shear behavior. The focus was not only on creep, as it is normally done, but on aging effects. The shear test devices allow the measurement of creep curves and times-to-failure at elevated temperatures in different media (tap water and de-ionized water). In this publication, the main findings of the experiments on needle-punched GCLs with and without thermal treatment are summarized. Tap water as a test medium was essential to ensure sodium to calcium ion exchange in the bentonite layer. Under this condition extremely long test durations without failure were achieved. Sliding failure occurred when de-ionized water was used. Two failure modes were observed: brittle failure of the GCLs with thermal treatment and slow disentanglement of fiber bundles for untreated GCLs. Short-term shear strength (e.g. peel strength) is unrelated to the actual long-term shear strength, i.e. to the times-to-failure achieved in long-term shear strength test. Hence, short-term shear strength alone will not provide reliable dimensioning data for product design and choice of resins. Therefore, the often suggested approach, namely, restriction to short-term tests only and application of factors of safety, is challenged by these results.
Highly soluble 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide-(DOPO)-based diamino hardener (2), bearing its amino groups directly on the DOPO framework, is investigated with respect to its use as a reactive flame retardant in thermosets. A mechanism for decomposition of the corresponding phosphorus-modified epoxy resin system based on a diglycidylether of bisphenol A DGEBA and 2 (DGEBA/2) is proposed and compared to the systems using DGEBA and 4,4'-diaminodiphenylsulfon (DGEBA/DDS) and to a similar system based on the structurally comparable non-reactive DOPO-based compound (DGEBA/DDS/1). Additive 1 changed the decomposition characteristics of the epoxy resin only slightly and phosphorus was released. Incorporating 2 induces two-step decomposition and most of the phosphorus remains in the residue. Furthermore, the fire behaviour of neat epoxy resin systems and a representative carbon fibre-reinforced composite based on DGEBA, DDS and 2 (DGEBA/DDS/2) were examined and compared to that of the analogous composite systems based on DGEBA/DDS and DGEBA/DDS/1. Based on different flame retardancy mechanisms both the reactive compound 2 and the additive compound 1 improve flammability (increase in LOI >13% and achieving V-1 behaviour) of the epoxy resin and composites. Under forced flaming only the flame inhibition of the additive compound 1 acts sufficiently. Lastly, the superior key mechanical properties of the epoxy resin and composite based on 2 are sketched.
Praktische Beispiele und Erfahrungen zu Störfallauswirkungsbetrachtungen - Freistrahlberechnungen -
(2008)
Damit Edelstahl rostfrei bleibt - Korrosionsschutzgerechte Verarbeitung von Edelstahl Rostfrei
(2008)