Filtern
Erscheinungsjahr
- 2008 (1562) (entfernen)
Dokumenttyp
- Vortrag (659)
- Zeitschriftenartikel (324)
- Posterpräsentation (238)
- Beitrag zu einem Sammelband (168)
- Beitrag zu einem Tagungsband (119)
- Dissertation (12)
- Forschungsbericht (10)
- Sonstiges (9)
- Buchkapitel (7)
- Zeitschriftenheft (Herausgeberschaft für das komplette Heft) (4)
- Monografie (3)
- Sammelband (Herausgeberschaft für den kompletten Band) (3)
- Tagungsband (Herausgeberschaft für den kompletten Band) (2)
- Newsletter (2)
- Jahresbericht (1)
- Handbuch (1)
Sprache
- Deutsch (1088)
- Englisch (462)
- Mehrsprachig (10)
- Französisch (1)
- Russisch (1)
Schlagworte
- Beton (12)
- Non-destructive testing (12)
- Radar (10)
- Fluorescence (9)
- Quality assurance (9)
- Concrete (8)
- Cultural heritage (8)
- NMR (8)
- DLC (7)
- Fluorescence spectroscopy (7)
Eingeladener Vortrag
- nein (659)
Die Wirksamkeit einer Abtrennung aus Holz mit mindestens 50 mm Wandstärke für Zündmittel der Klassifizierung 1.4B konnte überzeugend bestätigt werden. Außerhalb dieser Abtrennung war überhaupt keine Wirkung zu beobachten. Auch wenn die Originalverpackung leichterer Bauart vergleichsweise stark beschädigt wurde fungierte die hölzerne Abtrennung aus wirksamer Schutz gegen die entstandenen Splitter. Einer weiteren Anwendung der bisherigen Verfahrensweise steht aus sicherheitstechnischer Sicht nichts im Wege.
Tribological screening tests (simple, reciprocating ball-on-flat tests) were performed with the objective to identify an appropriate coating for the articulating surfaces of artificial hip joints whose acetabular cups and femoral stems are made from Ti6Al4V alloy, which is appreciated for its light weight, good biocompatibility and elastic properties similar to those of natural bone. Standard coatings like TiN or CrN performed better than more complicated multi-layer systems, though not as good as different types of amorphous carbon coatings, generally referred to as diamond-like carbon or DLC coatings. Among the latter, hydrogenated amorphous carbon (a-C:H) displayed the best properties, especially if the hydrogen content was increased by reducing the bias voltage during PA-CVD-deposition.
The optimised a-C:H coating revealed the most promising wear behaviour under the applied testing conditions, i.e. the increase of linear wear with the number of cycles was close to zero. Regarding the materials examined in this study, correlation of wear with mechanical properties obtained by nano-indentation revealed that high hardness was not an adequate criterion for selecting appropriate coatings. A high ratio of hardness and elastic modulus (H/E) proved to be more important. Microstructural and micro-analytical investigations revealed transformation of TiN and CrN to TiO2 and Cr2O3, respectively, and amorphous carbon was, at least partly, transformed to graphite. Furthermore, incorporation of Al2O3 from the ball was observed at a very fine scale. The wear debris of favourable coatings always formed agglomerates of nano-scale particles. It was shown that commercial nano-particles of Al2O3, Cr2O3 and carbon black are comparable to particles generated by the tribological tests. However, it is uncertain whether they are comparable to those formed during simulator studies or in vivo. Furthermore, the performance of the favourable coating has to be tested in a hip joint simulator before its potential for application in prostheses can be assessed.