BAM Dissertationsreihe
Filtern
Erscheinungsjahr
Dokumenttyp
- Dissertation (173)
Referierte Publikation
- nein (173)
Schlagworte
- Zerstörungsfreie Prüfung (7)
- Beton (6)
- Schweißen (5)
- Brandschutz (4)
- CFD (4)
- Ermüdung (4)
- Finite-Elemente-Methode (4)
- Holz (4)
- Simulation (4)
- Ultraschall (4)
Organisationseinheit der BAM
- 9 Komponentensicherheit (5)
- 7 Bauwerkssicherheit (4)
- 9.4 Integrität von Schweißverbindungen (4)
- 5 Werkstofftechnik (3)
- 5.3 Polymere Verbundwerkstoffe (3)
- 7.2 Ingenieurbau (2)
- 7.3 Brandingenieurwesen (2)
- 8 Zerstörungsfreie Prüfung (2)
- 3 Gefahrgutumschließungen; Energiespeicher (1)
- 3.1 Sicherheit von Gefahrgutverpackungen und Batterien (1)
103
Investigation of an active air sampling strategy for biocides, PCBs and PAHs at low air change rates
(2013)
The aim of this study was to develop a low volume air sampling strategy for biocides, polychlorinated biphenyls (PCB) and polycyclic aromatic hydrocarbons (PAH) at low air change rates. Firstly a method of measurement for the GC-MS-MS system had to be created before an adsorbent for the air sampling of these compound classes was selected in elution experiments with target compound solutions. The key requirements for the adsorbent were that it had to engender a faster and easier work-up process while reducing solvent consumption, as it is not the case for the frequently used polyurethane foam (PUF) and XAD adsorbents. Using the selected adsorbent, air sampling quality was tested and compared with the one of PUF in experiments performed in a Micro-Chamber/Thermal Extractor™ (μ- CTE™, Markes International) with target compound solutions. To achieve air sampling under the aforementioned conditions the influences of temperature, air circulation, air change rate and relative humidity on the emission behavior of the selected biocides, PCBs and PAHs were investigated. This investigation was carried out with self soaked wood samples in low volume air sampling experiments in a μ-CTE, 23 l and 24 l emission test chambers and 27 l showcases. Furthermore, an active air sampling strategy for biocides, PCBs and PAHs at low air change rates was successfully tested in a 24 l emission test chamber. Sampling volumes of 24-50 l were tested with the developed low volume air sampling strategy with limits of quantification between 1-27 μg m-3. A styrene divinylbenzene polymer was selected as a suitable adsorbent and sampling of at least 100 ng μl-1 of biocides, PCBs and PAHs without breakthroughs were possible with 200 mg of this polymer. This corresponds to a concentration range of 3000-6250 μg m-3 for these low sampling volumes. The low volume air sampling method developed in this study was successfully applied in projects investigating real wood samples in the μ-CTE as well as in low volume indoor air samples. In these experiments the applicability of the method was partly compared with a method using a different adsorbent.
102
Novel routes in flame retardancy of bisphenol A polycarbonate/impact modifier/aryl phosphate blends
(2013)
The massive use of electronic engineering products accompanied by high demands on fire safety has led to increasing interest in environmentally friendly flame retardancy of bisphenol A polycarbonate (PC) based materials. In this work, novel routes for enhancing the flame retardancy of PC/Impact Modifier/Aryl phosphate were studied with respect to pyrolysis (TG, TG-FTIR, ATR-FTIR, NMR), flammability (LOI and UL 94) and fire behavior (cone calorimeter at different irradiations). To improve charring of PC/ABSPTFE+Aryl phosphate, the exchange of bisphenol A bis(diphenyl phosphate) (BDP) with novel aryl phosphates was proposed. Two novel flame retardants were synthesized: 3,3,5-trimethylcyclohexylbisphenol-bis(diphenyl phosphate) (TMC-BDP) and bisphenol A- bis(diethylphosphate) (BEP). TMC-BDP was more stable than BDP, thus gave a potential to increase the chemical reactions between the components of the PC/ABSPTFE+Aryl phosphate, whereas more reactive BEP was expected to increase the cross linking activity with the polymer matrix. Nevertheless, the corresponding blends did not enhance the flame retardancy compared to PC/ABSPTFE+BDP. BEP in PC/ABSPTFE preferred to cross-link with itself instead of with PC, thus it showed poor fire protection performance. TMC-BDP gave as good results as BDP in PC/ABSPTFE material. The results delivered evidence that BDP possesses a high degree of optimization in PC/ABSPTFE system. To provide a novel impact modifier improving not only mechanical properties but also the fire retardancy of PC/BDP material, the replacement of highly flammable acrylonitrilebutadiene- styrene (ABS) with silicon acrylate rubber (SiR) with high content of polydimethylsiloxane (PDMS) was studied. In PC/SiRPTFE/BDP the replacement of ABS is beneficial, but PDMS worsened the BDP gas phase and condensed phase action. PDMS reacted also with PC during combustion. PDMS-PC and PDMS-BDP interactions led to silicon dioxide. In fact, the inorganic residue of PC/SiRPTFE/BDP contributed to fire residue and greatly improved the LOI of about 10 % in comparison to PC/ABSPTFE+BDP system. Thus, the use of SiR with high PDMS content is proposed as replacement of ABS in PC/Impact Modifier/BDP blend. To enhance the fire protection, the PC/SiRPTFE/BDP was combined with several adjuvants: (i) layered fillers: talc and organically modified layered silicate (LS), (ii) metal hydroxides: magnesium hydroxide (Mg(OH)2) and boehmite (AlO(OH)), (iii) metal oxides and carbonate: magnesium oxide (MgO) and silicium dioxide (SiO2) and calcium carbonate (CaCO3) as well as (iiii) hydrated metal borates: zinc borate (ZnB), calcium borate (CaB) and magnesium borate (MgB). It was demonstrated that the blend PC/SiRPTFE/BDP+filler is very sensitive to chemical (e.g. hydrolysis) and physical (e.g. viscosity) effects. Additionally,the large deformations of PC/SiRPTFE/BDP materials make difficult to optimize the char. Overall, the ZnB, MgB and CaB are proposed for enhancing the flame retardancy of PC/SiR/BDP with respect to flammability results, reduction of fire hazard and maximum of heat release rate. The results of this work enable the understanding of various mechanisms controlling the fire behavior and thus effective selection of the most appropriate flame retardant, impact modifier and inorganic fillers for producing fire resistant PC based polymers.
101
Eine Vielzahl von Schwergasunfällen der Vergangenheit verdeutlichen das Gefahrenpotential, das von brennbaren und vor allem toxischen Schwergasen ausgeht. Zur Bestimmung des Gefährdungsbereichs müssen in diesem Fall Ausbreitungsabschätzungen angestellt werden. Während der Gefährdungsbereich für brennbare Gase auf das Erreichen der unteren Explosionsgrenze (c > 1 Vol.-%) beschränkt ist, so ergibt sich bei der Freisetzung toxischer Gase ein weitaus größerer Gefahrenbereich. Toxische Gase haben auch in sehr geringen Konzentrationen (c < 3000 ppm) noch ein hohes Schadenspotenzial. Zur Abschätzung der Schwergasausbreitung kann die VDI-Richtlinie 3783 verwendet werden. Diese Richtlinie entspricht zurzeit dem Stand des Wissens in Deutschland. Die VDI 3783 macht keine Angaben zur Höhe und Breite der Schwergaswolke, welche sowohl im Rahmen von quantitativen Risikoanalysen als auch evtl. für die Kopplung eines Lagrangeschen-Partikelmodells mit dem Schwergasmodell erforderlich sind. In der vorliegenden Arbeit wurden deshalb Berechnungen mit verschiedenen Modellen zur Erweiterung der VDI 3783 durchgeführt. Die Berechnungsergebnisse wurden mit experimentellen Untersuchungen zur Länge, Breite und Höhe des Schwer- und Neutralgasbereichs verglichen und bewertet. Darüber hinaus wurde der Einfluss der Quellhöhe auf die Schwergasausbreitung untersucht. Hierbei wurde festgestellt, dass sich die Länge des Schwergasbereichs mit zunehmender Quellhöhe verringert und ab einer kritischen Höhe kein Schwergasbereich am Boden mehr vorliegt. Für Freisetzungshöhen über der kritischen Quellhöhe ist der Schwergaseffekt vernachlässigbar und es ist keine Berechnung nach der VDI 3783, Blatt 2 erforderlich. Die Freisetzung des Schwergases kann hierbei sowohl aus einer verfahrenstechnischen Anlage als auch aus handelsüblichen Gasflaschen erfolgen. Für die Freisetzung aus handelsüblichen Gasflaschen wurde ein mathematisches Modell zur Vorhersage des zeitabhängigen Massenstroms weiterentwickelt. Dieses Modell beinhaltet die Berechnung der instationären Wärmeleitung in der Flaschenwand, eine komplexe Beschreibung der Energieund Massenbilanzen sowie die Berücksichtigung einer Zweiphasenströmung. Zur Validierung des Modells wurden experimentelle Untersuchungen mit verschiedenen Gasen, Gasflaschengrößen und –typen durchgeführt. Experimentelle Ergebnisse und Berechnungen zeigen eine gute Übereinstimmung.
100
TRIP Stähle realisieren durch eine unter mechanischer Beanspruchung hervorgerufene Phasenumwandlung von metastabilen Austenit in Martensit (TRIP-Effekt) hohe Festigkeiten bei gleichzeitig guten Verformungseigenschaften. Während der Verarbeitung dieser Werkstoffe mittels Widerstandspunktschweißen können unter den prozessspezifischen extremen Aufheiz- und Abkühlraten Modifikationen des Austenitanteils hervorgerufen werden die als Folge lokal zu einer Änderung der mechanisch-technologischen Eigenschaften führen. Wesentliche Zielsetzung der vorliegenden Arbeit war daher die Analyse der Gefügestruktur im Bereich einer Punktschweißverbindung hinsichtlich der Änderung des Austenitanteils und den daraus resultierenden Änderungen der lokalen mechanischen Eigenschaften unter besonderer Berücksichtigung des TRIP-Effekts. Durch in-situ Beugungsuntersuchungen mittels hochenergetischer Synchrotronstrahlung erfolgte zunächst die Quantifizierung des metastabilen Austenitanteils im unbehandelten Grundwerkstoff. Darauf aufbauend wurden unter definierten Temperaturprofilen in Ofenversuchen die grundlegenden Aspekte der thermisch bedingten Austenitumwandlung im Aufheiz- und Abkühlprozess untersucht. Durch Gleeble-Versuche und Ofenexperimente wurden weiterführend verschiedene Temperaturprofile mit unterschiedlichen im Punktschweißprozess lokal vorliegende Spitzentemperaturen genutzt um eine systematische Bewertung des Einflusses der Temperatur und der Aufheiz- sowie der Abkühlbedingungen auf den Austenitgehalt unter realen Bedingungen zu ermöglichen. Durch Korrelationsuntersuchungen zwischen den mechanischen Kennwerten thermisch präparierter Zugproben und den mittels Metallographisch wie auch röntgenographisch ermittelten Austenitgehalten konnten die metastabilen, d.h. umwandlungsfähigen Austenitanteile bestimmt werden. Schließlich erfolgte eine Bewertung hinschlich der Übertragbarkeit der Ergebnisse auf reale Widerstandspunktschweißverbindungen. Es wurde dabei der Nachweis erbracht, dass die Austenit-Martensit-Phasenumwandlung lediglich in einem lokal eng begrenzen Werkstoffbereich am Übergang WEZ/Grundwerkstoff wirksam werden kann. Demzufolge führt der TRIP-Effekt zu keiner signifikanten Beeinflussung von Festigkeits- und Verformungseigenschaften im Fügebereich von widerstandspunktgeschweißten TRIP Stählen. Die ermittelten mechanischen Kennwerte wurden abschließend als Eingangsdaten für die numerische Simulation des Verformungs- und Festigkeitsverhaltens von Punkschweißverbindungen genutzt. Dabei wurde insbesondere die Notwendigkeit der Implementierung von mechanischen Kenndaten der Wärmeeinflusszone für eine realitätsnahe Modellierung von Scherzugversuchen untersucht.
99
The reduced size of nanoparticles (diameter < 100 nm) confers them high specific surface areas and permeability through many biological pathways resulting in high interaction with biological systems. Therefore, in the recent years, nanoparticles (NPs) have increasingly found many applications in biomedical research. Herein, silica-based NPs are among the most promising candidates for biomedical studies due to their relative low toxicity and the possibility of functional variability. The main focus of this thesis work has been the synthesis and characterisation of novel hybrid NPs with enhanced properties for biomedical studies. More specifically, suppression of protein adsorption and achievement of highly fluorescent NPs in serum-rich media are well focused. First, a chemical strategy for the preparation of highly fluorescent silica nanoparticles by covalent attachment of Alexa dyes and subsequent shielding by an additional pure silica shell is well presented. These nanoparticles were investigated by Dynamic light scattering (DLS), Transmission electron microscopy (TEM) and fluorescence spectroscopy, the latter includes determination of absolute fluorescence quantum yields of such scattering suspensions with an integrating sphere setup and the assignment of fluorescence intensity values. At low shelling extension core-shell fluorescent silica nanoparticles show smooth surfaces and high quantum yields, even comparable to those for free dyes. However, by increasing the amount of shell precursor, nanoparticle surfaces show raspberry morphologies and decay of the quantum yields. Secondly, two different types of novel silica-poly(ethylene glycol) hybrid nanoparticles (H- SiO2-PEG and G- SiO2@PEG) have been synthesized by use of the same polymer precursor: Here the influence of concentration of the polymer precursor poly(ethylene glycol) methyl ether-3-(triethoxysilyl) propyl urethane (mPEG-IPTES) on the particle properties was scrutinised. For polymer grafted NPs, the concentration of polymer precursor increases the PEG density and the hydrophobicity of the NPs surface. On the other hand, for condensated NPs, the polymer precursor influences the size, but not the density of polymer chains on the NPs surface, which indicates that PEG on the surface of the NPs effectively reduces the adsorption of Bovine serum albumin (BSA). Finally, the influence of polymer length on the ability to repel BSA adsorption onto nanoparticles is reported. SNPs@PEG with different molecular weights (mPEG: 350, 2000 and 5000 g/mol) were synthesized by nucleophilic substitution of tosylated mPEG to aminated silica nanoparticles (chemical grafting). The resulted hybrid nanoparticles were consistently characterized by DLS, TEM, Fourier transform infrared spectroscopy (FTIR), Thermogravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS). BSA at different concentrations were used as a model protein to study the protein-corona formation after adsorption onto the pristine and modified nanoparticles (SNPs@PEG). For pristine SNPs and SNPs@PEG (MW = 350 g/mol), zeta potential at different incubation times (0, 24 and 48 h) show a dynamic evolution of the nanoparticle-protein corona. Conversely, for SNPs@PEG with MW ≥ 2000 g/mol, a significant suppression of corona formation and time evolution was observed. In resume, protein corona is strongly influenced by the adsorption inhibition of PEG surfaces.
98
Characterization of Polymer Nanocomposites based on Layered Double Hydroxide and Carbon Nanotubes
(2013)
Polymer based nanocomposites by melt blending of synthesized ZnAl-Layered Double Hydroxide (ZnAl-LDH) and Polyolefines [Polypropylene (PP) and Polyethylene (PE)] and also Polylactide (PLA) with MgAl-LDH and multi-walled Carbon Nanotubes (MWCNT) were investigated. The LDH was organically modified by using a surfactant sodium dodecylbenzene sulfonate (SDBS) to increase the interlayer spacing of the LDH, so that polymer chains can intercalate the inter layer galleries. Some amount of maleic anhydride grafted PP and PE were incorporated in the nanocomposites based on PP and PE respectively to enable the interaction of the non-polar polymers (PP and PE) with the LDH. The resulting morphology was investigated by a combination of Differential Scanning Calorimeter (DSC), Small and Wide-angle X-ray scattering (SAXS and WAXS) and broadband dielectric relaxation spectroscopy (BDS). In case of LDH based nanocomposites (PP, PE and PLA), the homogeneity of the nanocomposites and the average number of stack size (4 – 7 layers) were determined using scanning micro focus SAXS (BESSY II). DSC investigations of PP and PE based LDH nanocomposites showed a linear decrease in crystallinity as a function of filler concentration. The extrapolation of this decreasing dependence to zero estimates a limiting concentration of 40 wt% and 45 wt% respectively. Above this amount of LDH the crystallinity of the polymers is completely suppressed. This finding is in agreement with WAXS investigations where the area below the crystalline reflections and amorphous halo were calculated and used to estimate the degree of crystallinity. PLA/LDH nanocomposites presented a little different behavior, the crystallinity of the polymer at first increases and then decreases as a function of LDH concentration. In this case the crystallinity will be suppressed at around 15 wt%. The dielectric spectra of the nanocomposites based on PP/LDH and PE/LDH show several relaxation processes which are discussed in detail. The intensity of the dynamic glass transition increases with the concentration of LDH. This is attributed to the increasing concentration of the exchanged anion dodecylbenzene sulfonate (SDBS) which is adsorbed at the LDH layers. Therefore, a detailed analysis of the β-relaxation provides information about the structure and the molecular dynamics in the interfacial region between the LDH layers and the polymer matrix which is otherwise dielectrically invisible (low dipole moment, non-polar). In case of PLA/LDH, three relaxation processes related to dynamic glass transition and one localized fluctuations were identified and analyzed in detail to understand the morphology. For this system, one dynamic glass transition process originates from the fluctuations of the interfacial molecules, second from the PLA matrix (polar polymer, C=O in the main chain) and the third from segments confined between the intercalated LDH sheets. Additional thermal investigations were carried out for PP/LDH and PLA/LDH samples. The increase in the rigid amorphous fraction (RAF) was observed in both the cases. This is attributed to the polymer molecules which are in close proximity to LDH sheets, as they hinder their mobility. This is analyzed in detail and related to the BDS results. PLA based MWCNT nanocomposites were investigated by BDS as initial result. The findings showed that between 0.5 and 1 wt% of CNT, a percolating network of the nanotubes is formed which leads to DC conductivity. This is due to the high aspect ratio of the CNTs and also the van der Waals interaction between the nanotubes which forms a network leading to conductivity.
97
In der vorliegenden Arbeit wird das Schädigungsverhalten eines kurzglasfaserverstärkten Polyamids analysiert. Die Mikrorissschädigung wird mittels Röntgenrefraktionsanalyse für verschiedene mechanische Betriebsbelastungen untersucht. Dabei werden Möglichkeiten und Grenzen der Röntgenrefraktionsanalyse für kurzglasfaserverstärkte Polyamide herausgearbeitet. Insbesondere werden der Einfluss der Faserorientierungsverteilung und der Einfluss der Schädigungsmechanismen auf die Röntgenrefraktionsanalyse und deren Ergebnisinterpretation betrachtet. Die Methode ermöglicht eine quantitative und phänomenologisch basierte Mikrorissschädigungscharakterisierung. Für den untersuchten Werkstoff tritt Mikrorissschädigung in Form von Faser-Matrix-Ablösung und Matrixrissbildung auf. Die Schädigungshöhe korreliert linear mit dem nichtlinear elastischen Dehnungsanteil und ist abhängig von der Art der Betriebsbelastung. Eine Feuchtigkeitsaufnahme des Werkstoffs kann das Mikrorissschädigungsverhalten deutlich beeinflussen. Die Schädigung durch Mikrorissbildung tritt vorrangig unter Zugbelastungen auf. Die Makroschädigung durch Einzelrissfortschritt wird in Abhängigkeit der Faserorientierung und des Feuchtegehalts in einem automatisierten Versuch charakterisiert. Aufgrund der gewonnenen Erkenntnisse wird ein empirisches Berechnungsmodell erstellt. Die Untersuchungen des Mikro- und Makroschädigungsverhaltens werden fraktografisch begleitet, um die in den Modellvorstellungen vorausgesetzten Schädigungs- und Versagensmechanismen abzusichern.
96
Due to the growing environmental awareness worldwide, containment provisions for CO2 emissions in mobility systems and increasing performance requirements the demands on mechanical systems and their materials continuously rise. These high demands require the implementation of new technical approaches, for example of light-weight strategies in automotive powertrains, and directly raise questions about the suitability of the most promising technical solution. Two basic parameters, the surface hardness of the tooth flanks and the core fatigue strength of the tooth root, illustrate exemplarily increasing demands on material grades used for gear wheels in automotive powertrains. In addition to light-weight strategies, a reduction in friction and an increase of the fatigue lifetime are two other major development directions to strive the mentioned targets. It is clear that any kind of solution must show an equal application profile, preferably an improvement, compared to the state-of- the-art solutions. For tribological systems, the following paths may offer lower friction and higher load carrying capabilities: 1. Alternative base oils and additives (such as esters, polyglycols), 2. Thin film coatings (e.g. DLC) and/or 3. Novel steel metallurgies. In previous investigations on the slip-rolling resistance of thin film coatings (a-C, ta-C, Zr(C,N)) the substrates were mainly made of the bearing steels 100Cr6H and Cronidur 30. Applying contact pressures of up to P0max = 2.9 GPa (FN = 2,000 N), the samples were tested up to 10 million load cycles in endurance tests. The aim of the present work is to broaden the research by varying the input parameters. Newly developed engine oil mixtures, high performance thin film coatings and alternative steel solutions are intensively investigated in highly stressed slip-rolling contacts at lubricant temperatures of 120°C. Specifically, in using new steel metallurgies, i.e. the high toughness and high strength steels V300 and NC310YW (Aubert & Duval) as well as CSS-42L (Latrobe Specialty Steel Company), in combination with thin film coatings, even if they compete in the uncoated state, the Hertzian contact pressures could be increased up to P0max = 4.2 GPa (FN = 5,000 N) without any surface failures of coating or substrate. It was shown that selected thin film coatings can minimize the wear rates down to nearly ‘zero-wear’ in highly stressed contacts [Woy08] [Woy11]. In addition, the studies revealed not only the high potential in slip-rolling resistance, but also a possible friction reduction down to 0.047 by use of uncoated steels with increased toughness. Compared to steels like 100Cr6H and Cronidur 30 this means a reduction in friction of approximately 40% under identical testing conditions. Different test series with newly developed base oil-additive formulations were investigated with specific emphasis on the frictional behavior of selected bio-no-tox EP/AW additives and friction modifiers. Additional influencing factors like the structural and surface conditions of the steels/coatings before and after the tests were analyzed by means of REM, EDX, XRD and TEM.
95
Untersuchungen zum Schallfeld niederfrequenter Ultraschallprüfköpfe für die Anwendung im Bauwesen
(2012)
Durch intensive praxisbezogene Forschung konnte in den letzten Jahrzehnten das Spektrum der zerstörungsfreien Prüfverfahren im Bauwesen deutlich erweitert werden. Die akustischen Methoden im Bereich des Niederfrequenz-Ultraschalls nehmen hierbei eine zentrale Rolle ein. Mit der Einführung von kontaktmittelfrei arbeitenden Prüfköpfen gelang es schließlich, eine breite Akzeptanz für diese Untersuchungsmethode in der Praxis zu erzielen. Bedingt durch die oft großen Untersuchungsflächen, rückte die Dauer der Messdatenaufnahme unter wirtschaftlichen Gesichtspunkten immer mehr in den Fokus der Forschung. Eine Optimierung der Messzeit durch den Einsatz von vollautomatischen Scannern oder von parallel arbeitenden Prüfköpfen ist nur einem begrenzten Umfang möglich. In der Grundlagenarbeit „Luftgekoppeltes Ultraschallecho-Verfahren für Betonbauteile“ zeigt Herr Dr.- Ing. B. Gräfe das Potenzial der berührungslos arbeitenden Schallanregung hinsichtlich der Verringerung der Messzeit auf. Das Ziel der vorliegenden Arbeit ist es, grundlegende Fragestellungen für eine baupraktische Anwendung des luftgekoppelten Ultraschallecho-Verfahrens zu beantworten. Die sich ausbildenden Wellenarten hängen maßgeblich vom Winkel, unter dem der Schallimpuls aus der Luft auf die Oberfläche auftrifft und dem Abstand des Prüfkopfes zum Bauteil ab. Ein zentraler Punkt ist daher die genaue Kenntnis der Eigenschaften der angeregten Schallfelder unter Berücksichtigung dieser Randbedingungen. Mit der physikalischen Beschreibung des Schallfeldes ist es möglich, das Messverfahren hinsichtlich der verschieden gestellten Prüfaufgaben zu optimieren und Auswertungs- algorithmen zur sicheren Interpretation der Messdaten zu entwickeln. Recherchen zum Thema der Schallfeldanalysen in Festkörpern im Niederfrequenz-Bereich ergaben, dass auch die Kenntnisse zu den bereits weitverbreiteten Kontaktprüfköpfen nicht in einem ausreichenden Umfang messtechnisch abgesichert waren. Daher wurden diese ebenfalls in das Messprogramm aufgenommen. Für die Bestimmung der Kennwerte des Schallfeldes von Ultraschallprüfköpfen wurde ein Prüfstand geplant und gebaut. Das Konzept des Prüfstandes ist so ausgerichtet, dass neben der räumlichen Erfassung des Schallfeldes zusätzlich die stofflichen Einflüsse des durchschallten Mediums erfasst werden. Dies wird durch die Messung an halbkugelförmigen Probekörpern mit unterschiedlichen Durchmessern erreicht. Der Schwerpunkt der Untersuchungen liegt auf dem Werkstoff Beton. Bei dem Probenmaterial handelt es sich um einen selbstverdichtenden Beton, dessen Zusammensetzung geringe schallschwächende Eigenschaften aufweist. Die Rezepturen für diese Betone wurden an der Technischen Universität Berlin entwickelt. Es wurden Serien von jeweils vier Probekörpern unterschiedlicher Materialeigenschaften hergestellt. Variiert wurde bei den Serien der Probekörper die Größe der Gesteinskörnung, um eine erste Einschätzung des Einflusses der Materialzusammen- setzung auf das Schallfeld vornehmen zu können. Die Messdaten werden mit einer eigenständig entwickelten Software aufgezeichnet und ausgewertet. Aus den experimentell gewonnenen Kennwerten werden anschließend erstmalig räumliche Schallfelder für den Niederfrequenz-Bereich im Beton berechnet. Die Verifikation der Messergebnisse erfolgte durch den Einsatz unterschiedlicher Simulationsverfahren, die durch Partnerinstitute durchgeführt wurden. Im baupraktischen Teil der Arbeit werden die Erfahrungen aus realen Schadensanalysen präsentiert. Hierauf aufbauend wurden im Rahmen einer parallel laufenden Forschungsarbeit Probekörper hergestellt, an denen erste Untersuchungen mit einer luftgekoppelten Schallanregung durchgeführt wurden. Zu diesem Zweck wurden neben den Schallfeldanalysen Parameterstudien zu den optimalen Bedingungen der Schallanregung notwendig. Insbesondere die Oberflächenwellen und deren störender Einfluss wurden hierbei systematisch untersucht. Neben der Präsentation erfolgreicher Ergebnisse werden auch die gegenwärtigen Grenzen des Verfahrens aufgezeigt.
94
Die vorliegende Arbeit beschäftigt sich mit der systematischen Untersuchung von gas- und aerosolförmigen Reaktionsprodukten beim Abbrand von pyrotechnischen Gegenstanden für den Indoor-Bereich. Dazu wurden alle Parameter der in meiner Diplomarbeit eigens dafür konstruierten Messkammer optimiert und eine Vielzahl an pyrotechnischen Gegenständen vermessen. Die Resultate wurden mit Messungen unter realen Bedingungen verglichen. Zur besseren Beurteilung wurden zusätzlich Emissionsmessungen bei fünf verschiedenen Feuerwerksshows, sowohl Indoor als auch Outdoor, durchgeführt. Als Hauptergebnis konnte festgestellt werden, dass die gas- und aerosolförmigen Reaktionsprodukte unabhängig von dem pyrotechnischen Gegenstand online und mit einer guten Zeitauflösung in der Messkammer detektierbar sind. Eine Korrelation der Resultate zu den Messungen unter realen Bedingungen konnte hergestellt werden. Des Weiteren wurde nachgewiesen, dass der Effekt der als raucharm deklarierten pyrotechnischen Gegenstände nicht durch geringere Anzahlkonzentrationen, sondern durch geringere Durchmesser der entstehenden Aerosole erzielt wurde. Resultierend daraus waren mehr Partikel alveolengängig.