Chemische Verfahrenstechnik
Filtern
Erscheinungsjahr
- 2013 (4) (entfernen)
Dokumenttyp
- Dissertation (4)
Referierte Publikation
- nein (4)
Schlagworte
- Carbon Nanotubes (1)
- Characterization (1)
- Charakterisierung (1)
- Comparability (1)
- Dangerous Goods Containers (1)
- Gasausbreitung (1)
- Gasfreisetzung (1)
- Gefahrgutbehälter (1)
- HDPE (1)
- Hydrotalkit (1)
- Kohlenstoffnanoröhren (1)
- Layered Double Hydroxide (1)
- Nanocomposites (1)
- Oxidative Degradation (1)
- Oxidativer Abbau (1)
- Polymer (1)
- Polymer Nanokomposite (1)
- Quellung (1)
- Risikoanalyse (1)
- Schwergas (1)
- Struktur-Eigenschaften Beziehungen (1)
- Swelling (1)
- VDI 3783 (1)
- Vergleichbarkeit (1)
Generally accepted quality criteria for the comparison of immunoassays are still missing and assay conditions vary greatly between different laboratories. To address this problem, the influence of different parameters on the overall assay performance was assessed, specifically for different enzyme immunoassays (EIAs) for the anthropogenic markers caffeine (CAF) and carbamazepine (CBZ). Special emphasis was dedicated to the parameters temperature, assay format and enzyme-substrate combination. The temperature parameter was systematically studied for all incubation steps of the direct EIA formats employing the photometric horseradish peroxidase (HRP) substrate 3,3’,5,5’- tetramethylbenzidine (TMB) and the fluorometric HRP substrate 3-(4-hydroxyphenyl)propionic acid for both analytes. A temperature decrease only during the competition step led to an increase in assay sensitivity by a factor of 10 to 15 for CBZ and CAF, respectively, independent of the enzyme substrate used. Room temperature experiments yielded the smallest coefficients of variations, minimizing the edge effect. The influence of the assay format on different performance parameters was studied with the determination of CAF in consumer products. In addition to the HRP substrates, the enzyme alkaline phosphate (AP) and its chromogenic substrate para-nitrophenyl phosphate and a fluorescent substrate, 4-methylumbelliferyl phosphate, were employed. Seven quality criteria were defined and validated to compare these immunoassays. The evaluation of the four criteria (sensitivity, measurement range, relative dynamic range and goodness of fit) for the standard curves revealed that the direct format is superior to the indirect format, with the HRP TMB format showing the best performance. Three additional criteria for an applicationdriven analysis of real samples, in this case CAF-containing beverages and cosmetics, confirmed this result in terms of accuracy as well as intra- and inter-plate precision. The enzyme-substrate combination was investigated when several direct CBZ assays were applied to the analysis of water samples; here, three HRP assays and four AP assays were studied, along with luminescence detection. The HRP assays reached better sensitivities and lower quantifiable concentrations compared to the AP assays. Only the HRP assays and the chemiluminescent AP juice assay fulfilled the requirements for the four criteria applied to standard curves; all other AP assays were not considered for application to real samples based on these criteria. The AP juice assay can only be employed for influent samples whereas all HRP assays are applicable to influent and effluent wastewater samples according to intra- and inter-plate precision. Furthermore, the HRP assays alone are suitable for surface water analysis; here, the chromogenic HRP TMB assay yielded the best results, as any type of water sample can be quantified with high precision. Whether these quality criteria, derived here for standard curves as well as their application to real samples, can be transferred to other immunoassay formats for quality assurance remains to be shown.
Eine Vielzahl von Schwergasunfällen der Vergangenheit verdeutlichen das Gefahrenpotential, das von brennbaren und vor allem toxischen Schwergasen ausgeht. Zur Bestimmung des Gefährdungsbereichs müssen in diesem Fall Ausbreitungsabschätzungen angestellt werden. Während der Gefährdungsbereich für brennbare Gase auf das Erreichen der unteren Explosionsgrenze (c > 1 Vol.-%) beschränkt ist, so ergibt sich bei der Freisetzung toxischer Gase ein weitaus größerer Gefahrenbereich. Toxische Gase haben auch in sehr geringen Konzentrationen (c < 3000 ppm) noch ein hohes Schadenspotenzial. Zur Abschätzung der Schwergasausbreitung kann die VDI-Richtlinie 3783 verwendet werden. Diese Richtlinie entspricht zurzeit dem Stand des Wissens in Deutschland. Die VDI 3783 macht keine Angaben zur Höhe und Breite der Schwergaswolke, welche sowohl im Rahmen von quantitativen Risikoanalysen als auch evtl. für die Kopplung eines Lagrangeschen-Partikelmodells mit dem Schwergasmodell erforderlich sind. In der vorliegenden Arbeit wurden deshalb Berechnungen mit verschiedenen Modellen zur Erweiterung der VDI 3783 durchgeführt. Die Berechnungsergebnisse wurden mit experimentellen Untersuchungen zur Länge, Breite und Höhe des Schwer- und Neutralgasbereichs verglichen und bewertet. Darüber hinaus wurde der Einfluss der Quellhöhe auf die Schwergasausbreitung untersucht. Hierbei wurde festgestellt, dass sich die Länge des Schwergasbereichs mit zunehmender Quellhöhe verringert und ab einer kritischen Höhe kein Schwergasbereich am Boden mehr vorliegt. Für Freisetzungshöhen über der kritischen Quellhöhe ist der Schwergaseffekt vernachlässigbar und es ist keine Berechnung nach der VDI 3783, Blatt 2 erforderlich. Die Freisetzung des Schwergases kann hierbei sowohl aus einer verfahrenstechnischen Anlage als auch aus handelsüblichen Gasflaschen erfolgen. Für die Freisetzung aus handelsüblichen Gasflaschen wurde ein mathematisches Modell zur Vorhersage des zeitabhängigen Massenstroms weiterentwickelt. Dieses Modell beinhaltet die Berechnung der instationären Wärmeleitung in der Flaschenwand, eine komplexe Beschreibung der Energieund Massenbilanzen sowie die Berücksichtigung einer Zweiphasenströmung. Zur Validierung des Modells wurden experimentelle Untersuchungen mit verschiedenen Gasen, Gasflaschengrößen und –typen durchgeführt. Experimentelle Ergebnisse und Berechnungen zeigen eine gute Übereinstimmung.
Characterization of Polymer Nanocomposites based on Layered Double Hydroxide and Carbon Nanotubes
(2013)
Polymer based nanocomposites by melt blending of synthesized ZnAl-Layered Double Hydroxide (ZnAl-LDH) and Polyolefines [Polypropylene (PP) and Polyethylene (PE)] and also Polylactide (PLA) with MgAl-LDH and multi-walled Carbon Nanotubes (MWCNT) were investigated. The LDH was organically modified by using a surfactant sodium dodecylbenzene sulfonate (SDBS) to increase the interlayer spacing of the LDH, so that polymer chains can intercalate the inter layer galleries. Some amount of maleic anhydride grafted PP and PE were incorporated in the nanocomposites based on PP and PE respectively to enable the interaction of the non-polar polymers (PP and PE) with the LDH. The resulting morphology was investigated by a combination of Differential Scanning Calorimeter (DSC), Small and Wide-angle X-ray scattering (SAXS and WAXS) and broadband dielectric relaxation spectroscopy (BDS). In case of LDH based nanocomposites (PP, PE and PLA), the homogeneity of the nanocomposites and the average number of stack size (4 – 7 layers) were determined using scanning micro focus SAXS (BESSY II). DSC investigations of PP and PE based LDH nanocomposites showed a linear decrease in crystallinity as a function of filler concentration. The extrapolation of this decreasing dependence to zero estimates a limiting concentration of 40 wt% and 45 wt% respectively. Above this amount of LDH the crystallinity of the polymers is completely suppressed. This finding is in agreement with WAXS investigations where the area below the crystalline reflections and amorphous halo were calculated and used to estimate the degree of crystallinity. PLA/LDH nanocomposites presented a little different behavior, the crystallinity of the polymer at first increases and then decreases as a function of LDH concentration. In this case the crystallinity will be suppressed at around 15 wt%. The dielectric spectra of the nanocomposites based on PP/LDH and PE/LDH show several relaxation processes which are discussed in detail. The intensity of the dynamic glass transition increases with the concentration of LDH. This is attributed to the increasing concentration of the exchanged anion dodecylbenzene sulfonate (SDBS) which is adsorbed at the LDH layers. Therefore, a detailed analysis of the β-relaxation provides information about the structure and the molecular dynamics in the interfacial region between the LDH layers and the polymer matrix which is otherwise dielectrically invisible (low dipole moment, non-polar). In case of PLA/LDH, three relaxation processes related to dynamic glass transition and one localized fluctuations were identified and analyzed in detail to understand the morphology. For this system, one dynamic glass transition process originates from the fluctuations of the interfacial molecules, second from the PLA matrix (polar polymer, C=O in the main chain) and the third from segments confined between the intercalated LDH sheets. Additional thermal investigations were carried out for PP/LDH and PLA/LDH samples. The increase in the rigid amorphous fraction (RAF) was observed in both the cases. This is attributed to the polymer molecules which are in close proximity to LDH sheets, as they hinder their mobility. This is analyzed in detail and related to the BDS results. PLA based MWCNT nanocomposites were investigated by BDS as initial result. The findings showed that between 0.5 and 1 wt% of CNT, a percolating network of the nanotubes is formed which leads to DC conductivity. This is due to the high aspect ratio of the CNTs and also the van der Waals interaction between the nanotubes which forms a network leading to conductivity.
Verschiedene experimentelle Untersuchungen sind zur Erlangung einer Zulassung für Gefahrgutverpackungen notwendig, um die Eignung der Verpackung für den Transport gefährlicher Guter nachzuweisen. Ziel sind keine absoluten Werte für die Zeit bis zum Versagen bei der Innendruckprüfung oder die mittlere Versagensfallhöhe, sondern die Veränderung des Verpackungsverhaltens bei dem Einsatz eines anderen HDPEs. Alle Kanister aus den vier verschiedenen Werkstoffen wurden speziell hergestellt, um die Werkstoffeigenschaften differenziert beurteilen zu können. Das Granulat, aus dem die Platten gepresst und die Kanister hergestellt wurden, stammte aus derselben Charge, um Schwankungen zwischen den Chargen als Einflussquelle auszuschließen. Die Wanddicke ist entscheidend, daher wurden die Verpackungen mit dem Computertomographen und mittels Streifenprojektionsverfahren vermessen und die Ergebnisse mit dem magnetostatischen Messverfahren verglichen. Die Verformung bei der Innendruckprüfung wurde mittels Stereo-Bildkorrelationsverfahren vermessen. Die Verschiebung in radialer Richtung sowie die aquivalente Dehnung wurden ausgewertet und konnten in der numerischen Berechnung nachgebildet werden. Ebenso deren starke Beschleunigung aufgrund der Quellung, indem die Temperatur im Materialgesetz entsprechend der Quellung verwendet wurde. Der Widerstand gegen Innendruck und das Absorptionsverhalten hangen von der Dichte des Werkstoffs ab. Die Konditionierung bei erhöhter Temperatur führt zu Nachkristallisation und zum Abbau von Eigenspannungen. Die Veränderung der Dichte zwischen den Werkstoffen kann anhand gepresster Platten beurteilt werden. Eine höhere Dichte führt zu einem besseren Bauteilverhalten unter Innendruck. Der Zusammenhang von mittlerer Versagensfallhöhe und der Schlagzugzähigkeit gekerbter Proben aus den Seitenwanden der Kanister sowie der Kerbschlagzähigkeit von gepressten Platten konnte nachgewiesen werden. Eine höhere Kerbschlagzähigkeit führt zu einer höheren mittleren Versagensfallhöhe. Eine geringe Beständigkeit gegen oxidativen Abbau senkt die mittlere Versagensfallhöhe drastisch. Bei einer hohen Beständigkeit gegen oxidativen Abbau führt die Vorlagerung mit Salpetersaure jedoch nicht zu einer Verringerung der mittleren Versagensfallhöhe im Vergleich zum Zustand ohne Vorlagerung. Der oxidative Abbau kann an gepressten Platten ermittelt werden und erlaubt einen Ruckschluss auf die Veränderung der mittleren Versagensfallhöhe.