Sanitär- und Kommunaltechnik; Umwelttechnik
Filtern
Dokumenttyp
- Vortrag (16)
- Beitrag zu einem Tagungsband (9)
- Zeitschriftenartikel (7)
- Posterpräsentation (2)
- Beitrag zu einem Sammelband (1)
Schlagworte
- Mauerwerkbruch (13)
- Rohstoffliches Recycling (9)
- Papierasche (6)
- BOFS (5)
- Poröse Granulate (5)
- Hydraulic reactivity (4)
- Lightweight concrete (4)
- Masonry rubble (4)
- Recycling (4)
- Blended cements (3)
Organisationseinheit der BAM
- 7.4 Baustofftechnologie (35) (entfernen)
Eingeladener Vortrag
- nein (16)
Im Verbundforschungsprojekt REALight wurden Leichtgranulate aus gemischtem Mauerwerkbruch in einem thermischen Blähverfahren im Pilotmaßstab hergestellt. Im Teilprojekt der BAM stand die Charakterisierung dieser Leichtgranulate und ihre Anwendung in gebundenen Systemen im Vordergrund. Im Rahmen des Abschlussvortrags wurden Ergebnisse zur Entwicklung von Steinergänzungsmörteln sowie Infraleichtbeton vorgestellt.
Fused cement clinker can be produced from molten basic oxygen furnace slag (BOFS) by way of a reductive thermochemical treatment. During the thermochemical treatment, oxidic iron is reduced to metallic iron and separated. The resulting low-iron slag has a chemical and mineralogical composition similar to ordinary Portland cement (OPC) clinker. In this study, the hydraulic reactivity of the fused clinker from BOFS with and without gypsum was investigated using isothermal calorimetry, differential scanning calorimetry, in situ X-ray diffraction and powder X-ray diffraction. Furthermore, a synthetic fused clinker without foreign ions and fused clinker produced by a mixture of both materials was studied. The hydraulic reaction of the fused clinker from BOFS was considerably slower than that of OPC. However, the reaction can be accelerated by adding gypsum as a sulfate carrier. Furthermore, the results showed an increased reaction rate with decreasing content of foreign ions such as Fe, P or Mn.
Im Jahr 2020 fielen in Deutschland rund 220 Millionen Tonnen mineralische Bau- und Abbruchabfälle an, die als Sekundärrohstoffquelle genutzt werden können. Trotz hoher Recyclingquoten wird ein Teil der mineralischen Bau- und Abbruchabfälle immer noch deponiert oder in Anwendungen mit geringen Qualitätsanforderungen eingesetzt, da ein effektives Recycling dieser heterogenen Abfälle recht kompliziert ist. Bauschutt ist ein heterogener, SiO2-reicher Sekundärrohstoff, der sich aus einem Gemisch verschiedener abgebrochener Baumaterialien wie Ziegel, Betonfertigteile, Leichtbeton, Porenbeton, Kalksandsteine, Natursteine, Gips und Mörtel zusammensetzt. Die genaue Zusammensetzung hängt von der Abbruchstelle, der Vorsortierung und der Wiederaufbereitung in der Recyclinganlage ab. Eine direkte Wiederverwendung als rezyklierte Gesteinskörnung ist aufgrund der uneinheitlichen Zusammensetzung und des bis zu 50 %igen Feinanteils nach der mechanischen Aufbereitung nicht zulässig. Eine Möglichkeit, Mauerwerksschutt effektiv zu recyceln, ist die rohstoffliche Verwertung über ein chemisch-hydrothermales Umwandlungsverfahren, das poröse Granulate erzeugt. Durch die Porenstruktur dieser hydrothermal gehärteten Granulate ergeben sich Anwendungsmöglichkeiten als Filter- oder Wasserspeichermaterial, die über den Bausektor hinausgehen. Diese neuartigen Granulate können leichte Gesteinskörnungen natürlichen Ursprungs (z. B. Lavasand, Bimsstein) oder Körner aus natürlichen Rohstoffen (z. B. Blähton) ersetzen. Die neue Recyclingstrategie spart natürliche Ressourcen. Im Vergleich zur Herstellung von Blähton ist der Energieverbrauch wesentlich geringer. Ziel des Verbundprojektes HYTEGRA war die Entwicklung eines Verfahrens zur Herstellung von leichten Gesteinskörnungen aus SiO2- und CaO-reichen Sekundärrohstoffen. Als Rohstoffe wurden Mauerwerksschutt als SiO2-Quelle und Papierasche aus der energetischen Verwertung von Reststoffen der Altpapierverwertung als CaO-Quelle eingesetzt. Der komplette Prozess von der mechanisch-physikalischen Aufbereitung über die Bildung des Grüngranulats bis zur hydrothermalen Härtung wurde entwickelt und im Labormaßstab getestet. Die Anwendungen des hydrothermal gehärteten Granulats als Wasserspeichermaterial für die innere Nachbehandlung von hochfestem Beton, Pflanzensubstrat und Filtermaterial in Bodenfiltern zur Abwasserreinigung wurden untersucht. Der Beitrag gibt einen Überblick über die wichtigsten Ergebnisse des erfolgreich abgeschlossenen Verbundforschungsprojekts HYTEGRA.
Heterogeneous construction and demolition waste can be used as raw material to produce lightweight aggregates (LWA) similar to expanded clays. In the joint research project “REALight”, LWA were produced from masonry rubble in a thermal expanding process using a pilot production plant with a rotary kiln. Our research focuses on the characterisation of the novel LWA and their use in different hydraulically bound applications.
Infra-lightweight concrete (ILC) was produced with the novel LWA, which accounts for two thirds of total aggregate volume, and Celitement, which is a hydraulic binder with a low carbon footprint. Its dry bulk density is ≤ 800 kg/m³. Strength and durability properties are comparable to ILC data from the literature.
Lime-based repair mortars (LRM) containing LWA are beneficial for sandstone conservation due to their similar properties regarding porosity, water absorption and strength. A two-layer repair mortar system, which consists of a filling mortar to fill large voids and a covering mortar to modulate the surface texture to the historic sandstone, was developed.
In our contribution, we present results of the LWA characterisation according to the European standard EN 13055:2016. Requirements and challenges of the use of the novel LWA in ILC and LRM are discussed.
Heterogeneous construction and demolition waste can be used as raw material to produce lightweight aggregates (LWA) similar to expanded clays. In the joint research project “REALight”, LWA were produced from masonry rubble in a thermal expanding process using a pilot production plant with a rotary kiln. Our research focuses on the characterisation of the novel LWA and their use in different hydraulically bound applications.
Infra-lightweight concrete (ILC) was produced with the novel LWA, which accounts for two thirds of total aggregate volume, and Celitement, which is a hydraulic binder with a low carbon footprint. Its dry bulk density is ≤ 800 kg/m³. Strength and durability properties are comparable to ILC data from the literature.
Lime-based repair mortars (LRM) containing LWA are beneficial for sandstone conservation due to their similar properties regarding porosity, water absorption and strength. A two-layer repair mortar system, which consists of a filling mortar to fill large voids and a covering mortar to modulate the surface texture to the historic sandstone, was developed.
In our contribution, we present results of the LWA characterisation according to the European standard EN 13055:2016. Requirements and challenges of the use of the novel LWA in ILC and LRM are discussed.
Steelmaking slag is a by-product of steel production of which 4.5 Mt were produced in 2020 in Germany alone. It is mainly used in road construction, earthwork and hydraulic engineering. A smaller part is returned to the metallurgical circle, used as fertilizer or landfilled.
With this use, iron oxides still contained in steelmaking slag are lost. In addition, the possibility of producing higher-grade products from steelmaking slag is foregone. In recent decades, many researchers have investigated the production of Portland cement clinker and crude iron from basic oxygen furnace slags (BOFS) via a reductive treatment. Carbothermal treatment of liquid BOFS causes a reduction of iron oxides to metallic iron, which separates from the mineral phase due to its higher density. Simultaneously, the chemical composition of the reduced slag is adapted to that of the Portland cement clinker.
In this study, German BOFS was reduced in a small-scale electric arc furnace using petrol coke as a reducing agent. The resulting low-iron mineral product had a similar chemical composition to Portland cement clinker and was rich in the tricalcium silicate solid solution alite (Ca3SiO5). Based on its chemical and mineralogical composition, similar to that of Portland cement clinker, the reduced BOFS has the potential to react comparably. In our study, the reduced BOFS produced less heat of hydration compared to OPC and its hydraulic reaction was delayed. However, adding gypsum has been shown to accelerate the hydration rate of the reduced BOFS compared to that known from the calcium silicates of Portland cement clinker.
Further research to improve the hydraulic properties of the reduced slag is essential. If successful, producing a hydraulic binder and crude iron from BOFS could have economic and ecological benefits for both the cement and steel industry.
Basic oxygen furnace slag (BOFS) is a by-product of steelmaking of which about 10.4 Mt are produced annually in the EU. BOFS is mostly used in road construction, earthwork and hydraulic engineering. However, in this use, the iron bound in BOFS is lost and the opportunity to produce higher value products from BOFS is forgone.
In recent decades, many researchers have investigated the production of both Portland cement clinker and crude iron from BOFS via a thermochemical reductive treatment. The reductive treatment of liquid BOFS causes a reduction of iron oxides to metallic iron, which separates from the mineral phase due to its higher density and can be recovered. An advantage of this process is that simultaneously the chemical composition of the reduced BOFS is adapted to that of Portland cement clinker and the hydraulic reactive mineral alite (Ca3SiO5) is formed.
In this study, German BOFS was reduced in a small-scale electric arc furnace and a low-iron mineral product rich in alite was produced. Despite a chemical and mineralogical composition similar to that of Portland cement clinker, the reduced BOFS produced less heat of hydration, and its reaction was delayed compared to Portland cement. However, adding gypsum accelerated the hydration rate of the reduced BOFS.
Further research to improve the hydraulic properties of the reduced BOFS is essential. If successful, the production of a hydraulic material and crude iron from BOFS could have economic and ecological benefits for both the cement and steel industry.
Jährlich fallen in Deutschland etwa 75 Mio. t mineralische Bau- und Abbruchabfälle an, die eine vielfältig einsetzbare sekundäre Rohstoffquelle darstellen. Trotz hoher Verwertungsquoten werden Bau- und Abbruchabfälle zum Teil deponiert oder nur in Anwendungen mit geringen Qualitätsanforderungen eingesetzt, weil geeignete hochwertige Verwertungswege für solche sehr heterogen zusammengesetzte Körnungen mit hohem Feinanteil fehlen. Der Reststoff Mauerwerkbruch ist ein heterogenes SiO2-reiches Gemisch aus Ziegel-, Beton- und Leichtbeton-, Kalksandstein- und Porenbetonbruch sowie Putz- und Mörtelanhaftungen. Die uneinheitliche Zusammensetzung und mehr als 50 % Feinanteile durch die mechanische Aufbereitung verhindern eine unmittelbare Wiederverwertung als rezyklierte Gesteinskörnung. Eine Möglichkeit der effektiven Verwertung von Mauerwerkbruch stellt das rohstoffliche Recycling über einen hydrothermalen Stoffumwandlungsprozess dar, bei dem poröse Granulate entstehen. Aus den Eigenschaften der Hydrothermalgranulate, insbesondere ihrer Porenstruktur, ergeben sich Anwendungsmöglichkeiten als Filter- oder Speichermaterial, d. h. auch in Bereichen, die über den Bausektor hinausgehen. Hierbei können die Granulate Gesteinskörnungen natürlichen Ursprungs, z. B. Lavasand und Bims, oder aus natürlichen Rohstoffen hergestellte Körnungen, z. B. Blähtone, ersetzen. Somit wird ein Beitrag zur Schonung natürlicher Ressourcen und zur Energieeinsparung im Vergleich zur Blähtonherstellung geleistet.
Ziel des ZIM-Kooperationsprojekts „HYTEGRA – Hydrothermalgranulate“ war die Entwicklung des Verfahrens zur Herstellung leichter Gesteinskörnungen durch die hydrothermale Behandlung eines Gemischs quarz- und kalkreicher Reststoffe. Als Ausgangsstoffe dienten ziegelhaltiger Mauerwerkbruch als SiO2-Träger und Papierasche aus dem Altpapierrecycling als CaO-Träger. Die vollständige Prozesskette von der mechanisch-physikalischen Aufbereitung der Reststoffe über die Formgebung der Grüngranulate bis zur hydrothermalen Härtung der Leichtgranulate wurde im Labormaßstab entwickelt und erprobt. Die Anwendung der Hydrothermalgranulate als Speichermaterial zur inneren Nachbehandlung von Beton und als Pflanzsubstrat sowie als Filtermaterial in Bodenfiltern zur Abwasserbehandlung wurde untersucht.
Im Vortrag wird ein Überblick über die Ergebnisse des erfolgreich abgeschlossenen Projekts „HYTEGRA“ gegeben.
Basic oxygen furnace slag (BOFS) is a by-product of steelmaking of which about 10.4 Mt are produced annually in the EU. BOFS is mostly used in road construction, earthwork and hydraulic engineering. However, in this use, the iron bound in BOFS is lost and the opportunity to produce higher value products from BOFS is forgone.
In recent decades, many researchers have investigated a thermochemical process to reduce iron oxides to metallic iron in molten BOFS. The metallic iron formed separates from the reduced slag due to its higher density and can be recovered. An advantage of this process is that simultaneously the chemical composition of the reduced slag is adapted to that of the Portland cement clinker and the hydraulic reactive mineral alite is formed.
In this study, BOFS was reduced in a small-scale electric arc furnace using petrol coke as reducing agent, and the hydraulic properties of the reduced, low-iron BOFS were investigated. Despite a chemical and mineralogical composition similar to that of Portland cement clinker, the reduced BOFS produced less heat of hydration, and its reaction was delayed compared to Portland cement. However, the addition of gypsum, as is also done in cement production from Portland cement clinker, has been found to accelerate the hydration rate of reduced BOFS.
Further research to improve the hydraulic properties of the reduced slag is essential. If successful, the production of a hydraulic binder and crude iron from BOFS could have economic and ecological benefits for both the cement and steel industry.
Ziel des Projekts HYTEGRA ist die Herstellung leichter Gesteinskörnungen durch hydrothermale Behandlung quarz- und kalkreicher Reststoffe. Als Ausgangsstoffe dienen heterogener Mauerwerkbruch aus Bau- und Abbruchabfällen als SiO2-Träger und Papierasche aus dem Altpapierrecycling als CaO-Träger. Für beide Reststoffe besteht derzeit ein Verwertungsdefizit. Das Verfahren beruht auf der Idee des rohstofflichen Recyclings, d. h. die chemisch-mineralogischen Stoffeigenschaften werden für die hydrothermale Stoffumwandlung genutzt. Bei der Härtung der Hydrothermalgranulate bilden sich Calciumsilicathydrat-Phasen (CSH) aus der Reaktion zwischen Quarzpartikeln und Kalk im Autoklav bei 200 °C und 16 bar Sattdampf.
Die Zementindustrie erzeugt etwa 6-7% der globalen CO2-Emissionen und steht damit als Industriezweig vor dem Hintergrund einer anvisierten Klimaneutralität vor gewaltigen Herausforderungen. Der Prozess der Klinkerherstellung wurde über die vergangenen Jahrzehnte bereits kontinuierlich optimiert. Seit 1990 ist es der deutschen Zementindustrie gelungen, die spezifischen CO2-Emissionen der Zementproduktion u. a. durch den Einsatz alternativer, nicht fossiler Brennstoffe und durch Absenkung des Klinkergehalts im Zement um 20 % zu senken. Weitere konventionelle Minderungsstrategien versprechen jedoch nur noch wenig zusätzliche Reduktion. Im Falle des Portlandklinkers besteht die Schwierigkeit darin, dass zwei Drittel der CO2-Emissionen rohstoffbedingt durch die Entsäuerung des Kalksteins (CaCO3) anfallen, die durch die beschriebenen Maßnahmen nicht weiter abgesenkt werden können. Vielmehr wird es erforderlich sein, noch zu entwickelnde oder zu optimierende Technologien anzuwenden und ggf. alle relevanten Ebenen wie Produktion, Weiterverarbeitung und Anwendung von Zement und Beton neu zu denken. Neben technologischen Ansätzen zur CO2-Abscheidung mit nachfolgender langfristiger Speicherung (Carbon Capture and Storage – CCS) oder Verwertung (Carbon Capture and Utilisation – CCU) werden auch alternative Rohstoffe für die Zementproduktion und alternative Bindemittel in Betracht zu ziehen sein.
Basic oxygen furnace slag (BOFS) is a by-product of the steelmaking process, of which about 10.4 Mt are produced annually in the European Union. Besides its predominant use in road construction, earthwork, and hydraulic engineering, it is also possible to use BOFS as a source material for Portland cement clinker.
The main difference in the chemical composition of BOFS from the chemical composition of Portland cement clinker is its high content of iron oxides (7-50 wt.%). In recent decades, many researchers have investigated the production of both Portland cement clinker and crude iron from BOFS via thermochemical reductive treatment. Carbothermal treatment of liquid BOFS causes reduction of iron oxides to metallic iron, which separates from the mineral phase due to its higher density.
In this study, German BOFS was reduced in a small-scale electric arc furnace using petrol coke as reducing agent. The produced low-iron mineral product was chemically similar to Portland cement clinker and contained the most important Portland cement mineral alite (Ca3SiO5) as main component. Besides alite, the mineral product contained other Portland cement clinker constituents such as belite (β-Ca2SiO4) and tricalcium aluminate (Ca3Al2O6).
The production of Portland cement clinker and crude iron from BOFS has economic and ecological benefits for both the cement and steel industry. Cement clinker from reduced BOFS may be used as a substitute for cement clinker from conventional cement production, thereby CO2 emissions will be reduced. The steel industry benefits from a high-value application for its by-products that avoids cost expensive landfilling and may even bring economic advantages. However, reductive treatment requires high temperatures and, for economic reasons, has to be carried out immediately after casting of the liquid BOFS, which is a logistical challenge for most steel plants. A cost-benefit analysis is therefore essential.
Basic oxygen furnace slags (BOFS) are a by-product of steel production. In 2016, 10.4 Mt of BOFS were produced in the European Union (EU). The main part of BOFS is used in road construction, earthwork and hydraulic engineering. A smaller part is returned to the metallurgical circle, used as fertilizer or landfilled. However, it is also possible to produce higher value products from BOFS. For example, many researchers have investigated the possibility of producing Portland cement clinker and crude iron from BOFS by a carbothermal post-treatment.
In this study, German BOFS was reduced in a small-scale electric arc furnace using petrol coke as reducing agent. The carbothermal treatment reduces the iron oxides in the BOFS to metallic iron, which accumulates at the bottom of the furnace by density separation. In addition to metallic iron, the process generates a mineral product rich in the tricalcium silicate solid solution alite. As the main constituent of Portland cement clinker, the hydraulic reactive mineral alite is of high economic importance.
In previous studies, the hydraulic reactivity of the mineral product was investigated by testing the compressive strength of blends with 70 wt.% ordinary Portland cement (OPC). Recent investigations focused on the hydraulic properties of the pure mineral product from the reduced BOFS. The heat of hydration of the mineral product was measured by isothermal calorimetry and compared with the heat of hydration of a synthetic low-iron slag and OPC. In addition, the formation of hydration products was investigated with differential scanning calorimetry (DSC) and x-ray diffraction analysis (XRD) on freeze-dried samples after defined curing times. The results of the calorimetric measurements indicate that the mineral product produced less heat of hydration and its reaction was delayed compared to the synthetic low-iron slag and OPC. Hydration products such as portlandite and calcium silicate hydrates (C-S-H) formed later and in lower amounts.
The production of a hydraulic material from BOFS by reductive treatment is of great interest to both the cement and steel industries. The substitution of cement clinker in OPC with a hydraulic material such as reduced BOFS leads to a reduction in greenhouse gas emissions from cement production. The steel industry benefits from an application for its by-products that avoids cost expensive landfilling and may even bring economic advantages. Furthermore, it may be possible to return the recovered crude iron to production.
Basic oxygen furnace slags (BOFS) are by-products of the steelmaking process. Several researchers have studied the production of Portland cement clinker and metallic iron from BOFS via a reductive treatment.
In this study, we applied a carbothermal reduction of BOFS in a technical-scale electric arc furnace and characterised the clinker-like products. Those clinker-like non-metallic products (NMPs) had a chemical and mineralogical composition comparable to clinker for ordinary Portland cement (OPC) and contained large elongated alite crystals as major component. The pure NMPs reacted more slowly and achieved a lower degree of hydration compared with commercial OPC.
If the reactivity of the products can be further increased by employing specific adaptations, it can be used as a full clinker substitute for OPC. Nevertheless, it is also an option to use the material without further modifications as a cement component or concrete addition, which contributes to the strength development in both cases.
There is an ongoing debate on European scale concerning the criticality of phosphorus. In Switzerland and Germany, phosphorus recovery from phosphorus-rich waste streams will become obligatory. Sewage sludge ash is rich in phosphorus and may become an important secondary feedstock. Thermochemical treatment of sewage sludge ash with sodium sulphate under reducing conditions was shown to remove heavy metals from the solid product and produce the fully plant available crystalline phase CaNaPO4. Pilot-scale experiments in a rotary kiln were carried out at temperatures between 750 and 1000 °C and were compared to laboratory-scale experiments with crucibles. Process upscaling was successfully demonstrated but a series of differences were noticed: In comparison to laboratory-scale, solubility of phosphorus in samples from pilot-scale experiments was lower at all chosen treatment temperatures because of shorter retention time and incomplete decomposition of sodium sulphate. X-ray diffraction analysis revealed remaining phase fractions of whitlockite (Ca3-x(Mg,Fe)x(PO4)2) and sodium sulphate from the starting materials in products and thus indicated incomplete reaction. In contrast to the results of laboratory-scale experiments, the crystalline phase CaNaPO4 was clearly absent in the products from the rotary kiln but instead a Mg-bearing phase (Ca,Mg)NaPO4 was formed. Laboratory-scale experiments confirmed (Ca,Mg)NaPO4 is an intermediate phase between whitlockite and CaNaPO4. However, both crystalline phases are characterized by high plant availability. It was shown that heavy metal removal increased at higher temperatures whereas solubility and thus plant availability of phosphorus already reached its maxima at temperatures of 950 °C in pilot-scale and 875 °C in laboratory-scale experiments.
Jährlich fallen in Deutschland ca. 56 Mio. t mineralischer Bauschutt an, der eine vielfältig einsetzbare sekundäre Rohstoffquelle darstellt. Trotz hoher Verwertungsquoten werden Bau- und Abbruchabfälle zum Teil deponiert, weil geeignete und rentable Verwertungswege fehlen. Der Reststoff Mauerwerkbruch ist ein heterogenes SiO2-reiches Gemisch aus Ziegel, Beton- und Leichtbetonsteinen, Kalksandstein, Porenbeton, Putz und Mörtel. Die un-einheitliche Zusammensetzung und mehr als 50 % Feinanteile durch die mechanische Aufbereitung verhindern meist eine unmittelbare Wiederverwertung als RC-Gemisch. Eine Möglichkeit der effektiven Verwertung von Mauerwerkbruchmehlen stellt das rohstoffliche Recycling über einen hydrothermalen Stoffumwandlungsprozess dar, bei dem poröse Granulate entstehen. Aus den Granulateigenschaften, insbesondere der Porenstruktur, ergeben sich Anwendungen als Filter- oder Speichermaterial, d. h. auch in Bereichen, die über den Bausektor hinausgehen. Hierbei können die Granulate leichte Gesteinskörnungen natürlichen Ursprungs, z. B. Lavasand oder Blähtone, ersetzen und somit einen Beitrag zur Schonung natürlicher Ressourcen leisten.
Im Fokus des aktuellen ZIM-Projekts HYTEGRA steht die Entwicklung eines solchen hydrothermalen Herstellungsprozesses und die umfassende Charakterisierung der hergestellten Hydrothermalgranulate. Als sekundäre Rohstoffquelle wird neben SiO2-reichem Mauerwerkbruch aus Bau- und Abbruchabfällen auch CaO-reiche Papierasche eingesetzt. Die-se Asche aus dem Altpapierrecycling weist ebenfalls ein erhebliches Verwertungsdefizit auf. Ihr Freikalk ermöglicht den Einsatz als Kalksubstitut. Die Herstellung der Hydrothermalgranulate erfolgt in einem mehrstufigen mechanischen Prozess mit abschließender hydrothermaler Behandlung. Das konventionell mechanisch aufbereitete Abbruchmaterial (RC-Gemisch < 32 mm) wird mittels Kugelmühle zu einem Mehl (< 120 µm) verarbeitet, welches im Intensivmischer unter Zugabe von Kalk und Wasser granuliert wird. Die Härtung der Grüngranulate erfolgt hydrothermal unter erhöhtem Druck in gesättigter Wasserdampfatmosphäre bei Temperaturen von etwa 200 °C. Während des Härtungsprozesses bilden sich aus Quarz (SiO2), Kalk (CaO) und Wasser Calciumsilicathydrat-Phasen, die für die benötigte Festigkeit und Porosität der Hydrothermalgranulate sorgen. Durch die Variation der Syntheseparameter Temperatur, Druck, Zeit und SiO2-CaO-Mischungsverhältnis während der hydrothermalen Härtung, aber auch durch die Prozessführung der Granulierung, wird die Variation und gezielte Einstellung der Eigenschaften der Hydrothermalgranulate ermöglicht. In Kooperation mit Industriepartnern werden die hergestellten Hydrothermalgranulate in verschiedenen Applikationsbereichen getestet, z.B. in Bodenfiltern zur Abwasserbehandlung sowie als temporärer Wasserspeicher zur inneren Nachbehandlung von hochfestem Beton und in Pflanzsubstraten.
Im Tagungsbeitrag wird das Projekt HYTEGRA vorgestellt, insbesondere der hydrothermale Verwertungsweg unter Verwendung von Mauerwerkbruch und Papierasche im Labor- und Technikumsmaßstab sowie die Anwendung der hergestellten porösen Granulate als Filter- und Speichermaterial.
Two brick clays (rich in 2:1 clay minerals) and a low-grade kaolinitic clay were studied regarding their transformations during calcination and their performance in blended cement mortars. The mortars with calcined clays exhibited decreased workability (slump flow), but this effect could be mitigated by employment of a conventional superplasticizer; however, compressive strength of the hardened mortar was lowered in some cases. While the kaolinitic clay generally yielded the highest strength, the performance of a brick clay could be increased by grinding to higher fineness and by mixing it with the kaolinitic clay.
Hydrothermale Herstellung von Filter- und Speichermaterialien aus SiO2- und CaO-reichen Reststoffen
(2019)
Aus SiO2- und CaO-reichen Sekundärrohstoffen können in einem hydrothermalen Stoffumwandlungsprozess poröse Körnungen (Hydrothermalgranulate HTG) hergestellt werden. Die Erhärtung der HTG erfolgt dabei in einem Autoklav bei ca. 200 °C und 1,6 MPa Sattdampf ähnlich dem Prozess der Kalksandsteinherstellung. Festigkeit und Gefüge der HTG entwickeln sich durch die Ausbildung von Calciumsilicathydraten (CSH-Phasen), die durch die Reaktion zwischen Quarzpartikeln (SiO2) und Kalk (CaO) entstehen. SiO2-Lieferant ist ziegelhaltiger Mauerwerkbruch, der als Hauptmineralphase Quarz enthält. Papierasche kann mit ihren Anteilen an Freikalk und anderen reaktive Calciumverbindungen als Kalkersatz dienen. Über die Mischungszusammensetzung und die Reaktionsbedingungen werden die Eigenschaften der Reaktionsprodukte gezielt gesteuert. Die HTG haben Rohdichten kleiner als 2000 kg/m³. Ihr Gefüge ist durch ein eher ungeordnetes System an Mesoporen und kleinen Makroporen mit Porenweiten kleiner 100 nm gekennzeichnet. Diese Porenstruktureigenschaften legen eine Anwendung der HTG als Filter- oder Speichermaterial nahe. Sie können natürliche Rohstoffe, wie Bims, Lavasand und fluviale Sande, aus Primärrohstoffen hergestellte Produkte, wie Blähton, Keramik und Aktivkohle, sowie erdölbasierte Kunststoffadditive ersetzen, wobei die typischen Filter- und Speichereigenschaften der herkömmlichen Produkte nahezu erreicht werden. Dadurch wird einerseits für Reststoffe, die gegenwärtig ein hohes Verwertungsdefizit aufweisen, eine hochwertige Wieder- bzw. Weiterverwertungsmöglichkeit geschaffen und die Abfallmenge vermindert. Andererseits erfolgt eine Schonung von knapper werdenden natürlichen mineralischen Rohstoffen und Erdöl. In einem Forschungsprojekt werden derzeit die technischen Möglichkeiten der hydrothermalen Herstellung von leichten porösen Körnungen aus Mauerwerkbruch, Kalk und Papierasche sowie die Anwendung der HTG als Filtermaterial in Bodenfiltern zur Abwasserreinigung und als Wasserreservoir in Substraten von Pflanzwänden und zur inneren Nachbehandlung hochfester Betone systematisch untersucht. Der Beitrag berichtet insbesondere über die experimentelle Entwicklung der hydrothermalen Synthesestrategie, die nachfolgende Charakterisierung der HTG und die Beziehungen zwischen Gefügekennwerten und technischen Eigenschaften der Körnungen.
Mineralische Bauabfälle stellen in den Industrienationen den größten Abfallstrom dar. Allein in Deutschland fallen jährlich mehr als 50 Mio. Tonnen Bauschutt an, der hauptsächlich aus Beton- und Mauerwerkbruch besteht. Dabei nehmen die Verwertungs- und Recyclingquoten bei den bereits etablierten herkömmlichen Einsatzgebieten für aufbereitete Bau- und Abbruchabfälle mit zunehmender Heterogenität des Materials ab. Ein höherwertiges Recycling mit dem Ziel das aufbereitete Material beispielsweise in Betonprodukten einzusetzen erfolgt heute in Deutschland lediglich im Rahmen von Pilotprojekten. So können die groben Körnungen des Betonbruchs als rezyklierte Gesteinskörnung im Beton eingesetzt werden. Besonders eingeschränkte Verwertungsmöglichkeiten liegen für Mauerwerkbruch vor, einem Gemisch aus Beton, Ziegel, Kalksandstein, Porenbeton, Mörtel, Natursteinen und anderen mineralischen Bestandteilen. Die Ursache hierfür ist neben der heterogenen Zusammensetzung des Materials auch dessen feine Kornverteilung, die durch den bei der mechanischen Aufbereitung zwangsläufig anfallenden Feinkornanteil von 30 bis über 40 Prozent bedingt ist.
Defizite in der Verwertung bestehen also besonders bei heterogenen feinkörnigen Gemischen. Hier müssen Ansätze gefunden werden, um eine hochwertige Wiederverwertung zu ermöglichen. Dafür ist eine möglichst gute Trennung der einzelnen Materialfraktionen ein bewährter Ansatz. Während Metalle mittels Band- und Wirbelstromabscheidern und leichte Fremdbestandteile über Windsichtung und Dichtesortierung ausgetragen werden können, ist eine Trennung der Materialien Ziegel, Mörtel und Beton, insbesondere für die feinen Fraktionen, derzeit technologisch und wirtschaftlich nicht umsetzbar.
Ein rohstoffliches Recycling dieser heterogen zusammengesetzten Abfälle unter Nutzung ihrer chemisch-mineralogischen Zusammensetzung ohne eine vorherige Trennung in die einzelnen Materialfraktionen bietet sich als Alternative an. Ergebnisse zur Herstellung von Leichtgranulaten aus Mauerwerkbruch und Tonen in einem thermischen Prozess ähnlich der Blähtonherstellung wurden bereits mehrfach veröffentlicht. Diese Recycling-Granulate (RCG) könnten unter anderem als leichte Gesteinskörnung für Betone verwendet werden.
Jährlich fallen ca. 250 Mio. t mineralische Reststoffe in Deutschland an, die eine vielfältig einsetzbare, sekundäre Rohstoffquelle darstellen. Der Einsatz von Reststoffen führt zur Schonung natürlicher Rohstoffe, zur Reduktion von CO2-Emissionen und zur Einsparung von Deponieraum. Der Reststoff Mauerwerkbruch ist ein heterogenes, SiO2-reiches Gemisch aus Ziegeln, Beton und Leichtbeton, Kalksandstein, Porenbeton, Putz und Mörtel. Die uneinheitliche Zusammensetzung und bis zu 50 % Feinanteile nach der mechanischen Aufbereitung verhindern eine unmittelbare Wiederverwertung als RC-Gemisch. Eine Möglichkeit der Verwertung von Mauerwerkbruch stellt das rohstoffliche Recycling über einen hydrothermalen Stoffumwandlungsprozess dar, bei dem poröse Granulate erhalten werden.
Im Fokus des ZIM-Projekts HYTEGRA steht die Entwicklung eines solchen Herstellungsprozesses und die umfassende Charakterisierung der hergestellten Hydrothermalgranulate. Als Reststoffe soll neben Mauerwerkbruch (SiO2-reich) aus Bau- und Abbruchsabfällen auch Papierasche (CaO-reich) aus dem Altpapierrecycling eingesetzt werden. Nach einem mehrstufigen mechanischen Prozess erfolgt die Härtung der Grüngranulate hydrothermal unter erhöhtem Druck in gesättigter Wasserdampfatmosphäre bei Temperaturen von etwa 200 °C. Während des Härtungsprozesses bilden sich aus Quarz (SiO2), Kalk (CaO) und Wasser Calciumsilicathydrat-Phasen, die für die benötige Festigkeit und Porosität der Hydrothermalgranulate sorgen. Durch die Variation verschiedenster Syntheseparameter (Temperatur, Druck, Zeit, SiO2-CaO-Mischungsverhältnis) wird eine gezielte Einstellung der Eigenschaften der Hydrothermalgranulate ermöglicht. In Kooperation mit verschiedenen Industriepartnern sind Anwendungen als Filter- und Speichermaterial geplant, z.B. in Bodenfiltern zur Abwasserbehandlung sowie als temporärer Wasserspeicher zur inneren Nachbehandlung von Beton und in Pflanzsubstraten.
Im Vortrag sollen das Projekt HYTEGRA und erste Ergebnisse des hydrothermalen Verwertungsweg unter Verwendung von Mauerwerkbruch im Labormaßstab vorgestellt werden.
Hydrothermale Herstellung von Filter- und Speichermaterialien aus SiO2- und CaO-reichen Reststoffen
(2019)
Jährlich fallen ca. 250 Mio. t mineralische Reststoffe in Deutschland an, die eine vielfältig einsetzbare, sekundäre Rohstoffquelle darstellen. Der Einsatz von Reststoffen führt zur Schonung natürlicher Rohstoffe, zur Reduktion von CO2 Emissionen und zur Einsparung von Deponieraum. Im Projekt HYTEGRA sollen Mauerwerkbruch (SiO2-reich), ein heterogenes Gemisch aus Ziegeln, Beton und
Leichtbeton, Kalksandstein, Porenbeton, Putz und Mörtel, sowie Papierasche (CaO-reich) aus dem Altpapierrecycling rohstofflich wiederverwertet werden. Die Entwicklung von porösen Körnungen über einen hydrothermalen Herstellungsprozess steht dabei im Fokus. In Kooperation mit verschiedenen Industriepartnern sind Anwendungen als Filter- und Speichermaterial geplant.
Mauerwerkbruch setzt sich aus unterschiedlichen Anteilen der üblichen Wandbaustoffe Ziegel, Beton- und Leichtbeton, Kalksandstein, Porenbeton sowie Mauer- und Putzmörtel zusammen. Bei seiner mechanischen Aufbereitung zum RC-Gemisch fallen häufig bis zu 50 % Feinanteile an. Die heterogene Zusammensetzung und der hohe Feinanteil verhindern eine Wiederverwertung nach einer einfachen mechanischen Aufbereitung. Eine Möglichkeit des Recyclings von Mauerwerkbruch ist aber ein hydrothermaler Stoffwandlungsprozess, durch den leichte poröser Granulate hergestellt werden.
Aus ziegelhaltigem Mauerwerkbruch werden unter Zusatz von Branntkalk nach dem Mahlen, Mischen und Granulieren des Rohmehls durch hydrothermale Verfestigung in einem Autoklav poröse Körnungen mit Rohdichten kleiner als 2000 kg/m³, die Hydrothermalgranulate, erhalten. Die Erhärtung erfolgt bei ca. 200 °C und 1,6 MPa Sattdampf ähnlich dem Prozess der Kalksandsteinherstellung. Festigkeit und Gefüge der Hydrothermalgranulate entwickeln sich durch die Ausbildung von Calciumsilicathydraten (CSH-Phasen), die durch die Reaktion zwischen Quarz, als Bestandteil von Mauerwerkbruch, und Kalk entstehen.
Über die Mischungszusammensetzung und die Reaktionsbedingungen können die Eigenschaften der Granulate gezielt gesteuert werden. Ihr Materialgefüge ist durch ein ungeordnetes System an Mesoporen und kleinen Makroporen mit Porenweiten kleiner 100 nm gekennzeichnet. Damit unterscheiden sich ihre Eigenschaften deutlich von denen der thermisch erhärteten Blähgranulate, da sich durch die CSH-Phasen eine ganz andere Gefüge- und Porenstruktur ausbildet. Aus den Granulateigenschaften ergeben sich Anwendungen als Filter- oder Speichermaterial, d.h. Applikationen, die über den Baustoffsektor hinausgehen.
In einem laufenden Forschungsprojekt wird mit 4 Industrie- und 2 Forschungspartnern aus den Bereichen Baustoffrecycling, Verfahrens- und Syntheseentwicklung, Partikelcharakterisierung so-wie Filter- und Betontechnologie ein Syntheseweg zur gezielten Herstellung hydrothermal erhärteter, körniger und poröser Produkte aus Mauerwerkbruch im Labor- und Pilotmaßstab entwickelt. Dazu gehört auch die Untersuchung aller Prozessschritte von der Aufbereitung der Ausgangsmaterialien über das Homogenisieren und Granulieren der Mehle bis zur hydrothermalen Behandlung der Granulate. Die Hydrothermalgranulate werden umfangreichen Eignungs- und Dauerhaftigkeitstests unterzogen.
Das aktuelle Forschungsvorhaben und insbesondere erste Ergebnisse zur hydrothermalen Synthese von Mauerwerkbruch-Kalk-Mischungen werden im Vortrag vorgestellt.
The use of calcined clays as supplementary cementitious materials (SCMs) has been identified as a viable option to decrease the CO2 emissions related to cement production. However, while extensive data is available about kaolinitic clays in this context, other clays such as illitic clays appear to be under-studied. Therefore, in the present study, two illitic clays were compared to two low-grade kaolinitic clays in terms of transformations in the calcination temperature range 650–900 °C, and performance of the calcined clays in blended cement pastes as measured by strength evolution, heat release, hydrated phase formation and portlandite consumption. The illitic clays required a higher calcination temperature for complete dehydroxylation of their illite than what is necessary for dehydroxylation of kaolinite. These higher calcination temperatures also led to particle sintering, significantly decreasing the specific surface area of the illitic clays, particularly for the clay with the higher Fe2O3 content. Nevertheless, while the kaolinitic clays generally exhibited the best performance as SCM, the illitic clay with lower Fe2O3 content performed similar to the kaolinitic clays when calcined at optimum temperature and applied at a moderate substitution rate. These findings demonstrate that several different clays have the potential to be used as SCM and indicate possible routes to identify suitable deposits for this purpose.
In the 21st century, adequate habitat and functioning infrastructure are critical for global societal and economic stability. In addition, growing urbanisation and environmental pollution cause challenges to societies.
With increasing velocity, humanity faces that the current way of living is not sustainable. Thus, habitat,infrastructure, urbanisation, environment and sustainability are definitively among the most striking challenges of the 21st century.
By consulting, planning, building, maintaining, exploiting and processing of global resources, civil engineers contribute significantly to the existence of these challenges. This is a high responsibility, but due to the heavy involvement, together with adjacent disciplines such as architecture, geosciences, chemistry,
physics, environmental sciences and economics, civil engineers also hold the key to mitigate these challenges and provide a brighter global future.
Solutions towards greener, more sustainable and economically viable materials do exist, and there is ongoing research on how greener technologies can contribute to better livelihood and economic growth, but their level of implementation is limited, a major reason for which is that these approaches require more fundamental understanding rather than standard application.
While today, engineers can choose from a wide range of rheology modifying admixtures, in some parts of the world, these are difficult to access, due to their complex processing. However, alternatives can be bio-based polymers such as polysaccharides from various sources. These are easily accessible all over the world, do not demand for complicated processing, and typically they are more sustainable than many established materials, which are crude oil-based.
The paper presents the effects of acacia gum, cassava starch and the gum of triumfetta pendrata A. Rich on the rheological performance of cementitious systems. It is shown that acacia gum can be as efficient as polycarboxylate based superplasticisers, cassava starch can reduce the yield stress slightly with little effect on the plastic viscosity, and the gum of triumfetta pendrata A. Rich increases the thixotropy of cement pastes with plasticizing polymers significantly.
While today, engineers can choose from a wide range of rheology modifying admixtures, in some parts of the world, these are difficult to access, due to their complex processing. However, alternatives can be bio‐based polymers such as polysaccharides from various sources. These are easily accessible all over the world, do not demand for complicated processing, and typically they are more sustainable than many established materials, which are crude oil‐based.
The paper presents the effects of acacia gum, cassava starch and the gum of triumfetta pendrata A. Rich on the rheological performance of cementitious systems. It is shown that acacia gum can be as efficient as polycarboxylate based superplasticisers, cassava starch can reduce the yield stress slightly with little effect on the plastic viscosity, and the gum of triumfet ta pendrata A. Rich increases the thixotropy of cement pastes with plasticizing polymers significantly.
Structural design and application have always been linked to the compressive strength of concrete as the main relevant criterion. This was justifiable in the past, where concrete consisted of water, ordinary Portland cement and aggregates, but this concept is no longer relevant for modern and more sustainable cement and concrete.
Despite these new developments, existing standards, guidelines and academic curricula have not been much updated and are still used worldwide. There is a need to change this situation by proper education of the users.
This overview describes the challenges that arise at a user Level from the higher complexity of modern concrete, and defines needs and requirements for enhanced applicability of sustainable concrete concepts.
Furthermore, recommendations are given on how better concrete practice can be communicated to all the involved parties, from civil and design engineers to constructors and site-appliers on the construction site.
The production of Portland cement causes a substantial environmental impact, since the calcination of limestone results in high emissions of carbon dioxide. The use of supplementary cementitious materials such as calcined clays as partial replacement for Portland cement offers a solution to limit this environmental impact. This paper investigates four clays from deposits in central Germany with the aim of obtaining pozzolans for the production of Portland-pozzolana cement. The results obtained show that the calcined clays possess pozzolanic proper¬ties, which differ depending on calcination temperature and the relative amounts of kaolinite and 2:1 clay minerals.
The production of Portland cement causes a substantial environmental impact, since the calcination of limestone results in high emissions of carbon dioxide. The use of supplementary cementitious materials such as calcined clays as partial replacement for Portland cement offers a solution to limit this environmental impact. This paper investigates four clays from deposits in central Germany with the aim of obtaining pozzolans for the production of Portland-pozzolana cement. The results obtained show that the calcined clays possess pozzolanic properties, which differ depending on calcination temperature and the relative amounts of Kaolinite and 2:1 clay minerals.
Lightweight concrete with recycling aggregates made from masonry rubble and rubble-clay mixtures
(2018)
Structural lightweight concrete is a construction material composed primarily of lightweight aggregates (LWA), cement and water. Most LWA are produced by thermal treatment of natural raw materials such as clay and shale today. In addition to the high energy costs thereby incurred, the availability of suitable raw materials is limited. An alternative is the use of recycling LWA made from mineral construction and demolition waste. Recycling LWA made from masonry rubble and rubble-clay mixtures were studied in two different research projects. The technology pursues the idea of feedstock recycling, which means the recycling is based on the chemical and mineralogical composition of the masonry rubble and clay. The recycling LWA are produced in a multistage manufacturing process by thermal hardening in laboratory and pilot scale. Their particle bulk densities and particle strengths vary between 600 and 2000 kg/m³ and 1.5 and 13 MPa, respectively. Their equivalence to traditional LWA was proven in comprehensive tests of the aggregates themselves as well as the mortars and concretes made therefrom. Our contribution reports on the results of the characterization of the recycling aggregates compared to expanded clays and the studies on LWA concretes.
Mineralische Bauabfälle stellen in den Industrienationen den größten Abfallstrom dar.
Allein in Deutschland fallen jährlich mehr als 50 Mio. Tonnen Bauschutt an, der hauptsächlich aus Beton- und Mauerwerkbruch besteht. Dabei nehmen die Verwertungs- und Recyclingquoten bei den bereits etablierten herkömmlichen Einsatzgebieten für aufbereitete Bau- und Abbruchabfälle mit zunehmender Heterogenität des Materials ab. Ein höherwertiges Recycling mit dem Ziel das aufbereitete Material in hochwertigen Betonprodukten einzusetzen erfolgt heute in Deutschland lediglich im Rahmen von Pilotprojekten. So können die groben Körnungen des Betonbruchs als rezyklierte Gesteinskörnung im Beton eingesetzt werden. Besonders eingeschränkte Verwertungsmöglichkeiten liegen für Mauerwerkbruch vor, einem Gemisch aus Beton, Ziegel, Kalksandstein, Porenbeton, Mörtel, Natursteinen und anderen mineralischen Bestandteilen. Die Ursache hierfür ist neben der heterogenen Zusammensetzung des Materials auch dessen feine Kornverteilung, die durch den bei der mechanischen Aufbereitung zwangsläufig anfallenden Feinkornanteil von 30 bis über 40 Prozentbedingt ist.
Defizite in der Verwertung bestehen also besonders bei heterogenen feinkörnigen Gemischen. Hier müssen Ansätze gefunden werden, um eine hochwertige Wiederverwertung zu ermöglichen. Dafür ist eine möglichst gute Trennung der einzelnen Materialfraktionen ein bewährter Ansatz. Während Metalle mittels Band- und Wirbelstromabscheidern und leichte Fremdbestandteile über Windsichtung und Dichtesortierung ausgetragen werden können, ist eine Trennung der Materialien Ziegel, Mörtel und Beton, insbesondere für die feinen Fraktionen, derzeit technologisch und wirtschaftlich nicht umsetzbar. Ein rohstoffliches Recycling dieser heterogen zusammengesetzten Abfälle unter Nutzung ihrer chemisch-mineralogischen Zusammensetzung ohne eine vorherige Trennung in die einzelnen Materialfraktionen bietet sich als Alternative an. Ergebnisse zur Herstellung von Leichtgranulaten aus Mauerwerkbruch und Tonen in einem thermischen Prozess ähnlich der Blähtonherstellung wurden bereits mehrfach veröffentlicht. Diese Recycling-Granulate (RCG) sollen unter anderem als leichte Gesteinskörnung für Betone verwendet werden. Gegenstand dieses Beitrags sind Ergebnisse aus dem Verbundforschungsprojekt „RC-Leichtgranulate“ zum Einsatz der RCG in Leichtbeton.
Lightweigt concrete with recycling aggregates made from masonry rubble and rubble-clay mixtures
(2018)
Structural lightweight concrete is a construction material composed primarily of lightweight aggregates (LWA), cement and water. Most LWA are produced by thermal treatment of natural raw materials such as clay and shale today. In addition to the high energy costs thereby incurred, the availability of suitable raw materials is limited. An alternative is the use of recycling LWA made from Mineral construction and demolition waste. Recycling LWA made from masonry rubble and rubble-clay mixtures were studied in two different research projects. The technology pursues the idea of feedstock recycling, which means the recycling is based on the chemical and mineralogical composition of the masonry rubble and clay. The recycling LWA are produced in a multistage manufacturing process by thermal hardening in laboratory and pilot scale. Their particle bulk densities and particle strengths vary between 600 and 2000 kg/m³ and 1.5 and 13 MPa, respectively. Their equivalence to traditional LWA was proven in comprehensive tests of the aggregates themselves as well as the mortars and concretes made therefrom. Our contribution reports on the results of the characterization of the recycling aggregates compared to expanded clays and the studies on LWA concretes.
Mineralische Bauabfälle stellen in den Industrienationen den größten Abfallstrom dar. Allein in Deutschland fallen jährlich mehr als 50 Mio. Tonnen Bauschutt an, der haupt-sächlich aus Beton- und Mauerwerkbruch besteht. Dabei nehmen die Verwertungs- und Recyclingquoten bei den bereits etablierten herkömmlichen Einsatzgebieten für aufbereitete Bau- und Abbruchabfälle mit zunehmender Heterogenität des Materials ab. Ein höherwertiges Recycling mit dem Ziel das aufbereitete Material in hochwertigen Betonprodukten einzusetzen erfolgt heute in Deutschland lediglich im Rahmen von Pilotprojekten. So können die groben Körnungen des Betonbruchs als rezyklierte Gesteinskörnung im Beton eingesetzt werden. Besonders eingeschränkte Verwertungsmöglichkeiten liegen für Mauerwerkbruch vor, einem Gemisch aus Beton, Ziegel, Kalksandstein, Porenbeton, Mörtel, Natursteinen und anderen mineralischen Bestandteilen. Die Ursache hierfür ist neben der heterogenen Zusammensetzung des Materials auch dessen feine Kornverteilung, die durch den bei der mechanischen Aufberei-tung zwangsläufig anfallenden Feinkornanteil von 30 bis über 40 Prozent bedingt ist.
Defizite in der Verwertung bestehen also besonders bei heterogenen feinkörnigen Ge-mischen. Hier müssen Ansätze gefunden werden, um eine hochwertige Wiederverwertung zu ermöglichen. Dafür ist eine möglichst gute Trennung der einzelnen Materialfrak-tionen ein bewährter Ansatz. Während Metalle mittels Band- und Wirbelstromabscheidern und leichte Fremdbestandteile über Windsichtung und Dichtesortierung ausgetragen werden können, ist eine Trennung der Materialien Ziegel, Mörtel und Beton, insbesondere für die feinen Fraktionen, derzeit technologisch und wirtschaftlich nicht umsetzbar. Ein rohstoffliches Recycling dieser heterogen zusammengesetzten Abfälle unter Nutzung ihrer chemisch-mineralogischen Zusammensetzung ohne eine vorherige Trennung in die einzelnen Materialfraktionen bietet sich als Alternative an. Ergebnisse zur Herstellung von Leichtgranulaten aus Mauerwerkbruch und Tonen in einem thermischen Prozess ähnlich der Blähtonherstellung wurden bereits mehrfach veröffentlicht. Diese Recycling-Granulate (RCG) sollen unter anderem als leichte Gesteinskörnung für Betone verwendet werden. Gegenstand dieses Beitrags sind Ergebnisse aus dem Verbundforschungsprojekt „RC-Leichtgranulate“ zum Einsatz der RCG in Leichtbeton.
Slags from the nonferrous metals industry have great potential to be used as feedstocks for the production of alkali-activated materials. Until now, however, only very limited information has been available about the structural characteristics of these materials. In the work presented herein, synthetic slags in the CaO–FeOx–SiO2 system, representing typical compositions of Fe-rich slags, and inorganic polymers (IPs) produced from the synthetic slags by activation with alkali Silicate solutions have been studied by means of X-ray absorption near-edge structure (XANES) spectroscopy at the Fe K-edge. The iron in the slags was largely Fe2+, with an average coordination number of approximately 5 for the iron in the amorphous fraction. The increase in average oxidation number after alkali-activation was conceptualized as the consequence of slag dissolution and IP precipitation, and employed to calculate the degrees of reaction of the slags. The degree of reaction of the slags increased with increasing amorphous fraction. The iron in the IPs had an average coordination number of approximately 5; thus, IPs produced from the Fe-rich slags studied here are not Fe-analogs of aluminosilicate geopolymers, but differ significantly in terms of structure from the latter.