Ingenieurbau
Filtern
Dokumenttyp
Sprache
- Englisch (17)
Referierte Publikation
- ja (17) (entfernen)
Schlagworte
- Experimental modelling (2)
- Liquid cargo (2)
- Sloshing (2)
- Tanker (2)
- Aerial survey (1)
- Avoid (1)
- Braking (1)
- Braking in a turn manoeuvre (1)
- Capsizing (1)
- Cargo shifting (1)
Organisationseinheit der BAM
The dynamic response of a vehicle during braking is influenced by the tangential forces developed at the wheel-rail’s contact surface. The friction coefficient affects the load transfer from the wheel’s tread to the vehicle. In this work, the vibrations of a scale-down railway vehicle are monitored during braking and their relationship with the friction coefficient between wheel and rail is found out. The vehicle is instrumented with encoders, accelerometers, and is controlled via Bluetooth.
The tests are carried out with clean and friction-modified rails. The tangential forces transmitted from the wheel to the railcar’s body are visualized in time and frequency using a proposed correlation algorithm based on the outputs of the ContinuousWavelet Transform (CWT). The results demonstrate
that tangential forces have a significant impact on railway vehicles under conditions of high friction coefficients and large creep values.
A methodology is proposed for the experimental analysis of the liquid cargo effect under combined orthogonal accelerations. To simultaneously subject the vehicle-cargo system to longitudinal and lateral accelerations, the vehicle is set obliquely on a tilt table. The experimental outputs suggest that there is a significant effect of the liquid cargo on the lateral load transfer ratio (LTR), on the order of 20%, which is attributable to the resulting shifting of the liquid cargo’s centre of gravity. That is, the peak LTR values due exclusively to sloshing were not significant, in such a way that the liquid cargo would only pose a safety risk under a steady acceleration input.
Also, the inverse of the product of the magnitude of the acceleration times the free surface length, correlates with the liquid cargo effect. That is, the magnitude of the input acceleration is not fully determinant for greater load transfers.
This paper presents a method for processing acceleration data registered on a train and determining the health condition of a subway’s substructure. The acceleration data was converted into a dynamic deformation by applying a transfer function defined using the Empirical Mode Decomposition Method.
The transfer function was constructed using data produced on an experimental rig, and it was scaled to an existing subway system. The equivalent deformation improved the analysis of the dynamic loads that affect the substructure of the subway tracks because it is considered the primary load that acts on the track and substructure. The acceleration data and the estimated deformations were analyzed with the Continues Wavelet Transform. The equivalent deformation data facilitated the application of a health monitoring system and simplified the development of predictive maintenance programs for the subway or railroad operators. This method better identified cracks in the substructure than using the acceleration data.
Hunting is a potentially dangerous phenomenon related to the lateral oscillation of the wheels that impacts the rails and causes the wear of the infrastructure’s components. Therefore, the analysis and timely detection of hunting can lead to the application of corrective maintenance tasks, reducing damages, and costs and even derailments as a result. In this work, the vibration response of a finite element model of a rail with hunting-induced loads by a single wheel is analyzed in three directions: longitudinal, lateral, and vertical. The contact patch forces are calculated by means of Simpack® using the Kalker linear theory and the contact Hertz theory. The system is solved by using the Newmark-_ approach. The results of the deflection and vibration analysis, following the proposed methodology, show how the different characteristics of the loads impact the rail.
The objective of this paper is to describe and to validate a simplified pendulum-analogy model to simulate the interaction of a liquid cargo with ist carrying vehicle. The resulting testing rig consists of a rectangular container, spring supported on a two wheelset-bogie having a scale down of 1/10 with respect to a full-size equipment. The testing rig is used to validate a simple pendulum-based, simplified three degree-of-freedom mathematical model of the response of a partially filled container to lateral accelerations. The length of the pendulum is set according to validated methodologies. The resulting mathematical scheme reveals a high correlation with the experimental output, on the order of 99%, while some other performance measures, related to the peak forces and the range of variation of the wheel-rail forces, also show good concordance with the experimental results.
Vehicle’s components damage
(2020)
The failure of vehicle’s suspension components has contributed to road crashes, while their defective operation can deteriorate the fuel efficiency of the vehicles. In this context, and when compared with solid cargo transporters, the road tankers would tend to produce larger roll forces during turning, as the curved shape of the liquid cargo container, shifts upwards the centre of gravity of the cargo. With reference to a rectangular cargo container representing the solid cargo situation, the increase in the position due to elliptical and circular tank shapes, can attain a value of 17% (100% fill, circular tank). In this study, experimental results comparing the lateral load transfer due to solid and liquid cargoes, indicate that the average force increase on the vehicle’s load-receiver side due to a liquid cargo, is 4.3%. To analyse the fullscale situation of both situations, that is, the higher position of the centre of gravity and the shifting of the liquid cargo, a simplified model is developed. The outputs from such a model when subjected to realistic operating conditions (speed
and turning radius), suggest that the higher position of the centre of gravity due to using a non-rectangular cargo container generates an average force increase of 4.9% on the side receiving the load transfer. The incorporation of the effect of the liquid cargo, through the simple pendulum analogy, suggests that such an average increases to 6.76%, with a maximum of 8.35% in the case of the elliptical tank at 75% fill level. It is found that the average liquid cargo effect is 5.44%, which should be compared with the 4.3% of the experiments. Road tankers components would thus have a relatively shorter load cycle life than those of the solid cargo trucks.
Greenhouse gas emissions caused by human activities remain one of the most important subjects of international discussions. The routine gas flaring has been estimated to be responsible for as much as 1% of global carbon dioxide emission per year. Gas flaring analysis is one of the key-interest subjects in remote sensing community. Some of the existing publications use remote sensing techniques with satellite imagery to derive information about flame temperature and further about to estimate the volume of the flared gas. The often missing element is an in-situ measurement analysis of gas flames, combining signals recorded by a camera on-ground and data on flared gas volume, temperature and gas type. In order to address this problem, an experiment was conducted, in which the gas flame was recorded by thermal cameras on-ground, simultaneously to an aerial survey and the gas flow was measured at the same time on-ground. The measurement setup was designed in cooperation between Institute of Optical Sensor Systems of German Aerospace Center (DLR) and German Federal Institute for Materials Research and Testing (BAM). Cameras recording in thermal and mid-wave IR wavelengths were used to record the burning gas on-ground and from the aerial survey. All the measurements have been compared and statistically analysed with respect to the recorded temperature. The purpose of the examination was to describe the signal changes in thermal imagery with respect to changes in energy, emitted by the burning process. This approach will allow for later calculation of the amount of energy in form of thermal radiation sent from the flame to the satellite.
An experimental testing rig has been proposed to study the dynamic interaction between a liquid cargo and the carrying vehicle during turning maneuvers. The basic operational principle of the testing rig consists in simulating the lateral accelerations associated to turning maneuvers through the use of a tilt table.
While the experimental capabilities of the testing rig include the analysis of the effects of the cars on the whole transport infrastructure, including sleepers and ballast, a first use of the rig considered the effect of sloshing cargo on the level of dynamic forces transmitted to the rails. Such test was used to validate a simplified theoretical approach consisting of a two degree-of-freedom double pendulum mechanical system, where a simple pendulum, representing the sloshing cargo, is articulated to the spring-supported vehicle chassis, which is modelled as an inverted torsional pendulum. While the theoretical results exhibit a high correlation with the experimental data, the main discrepancy between both outputs, relates with the frequency of the residual vibration, once the lateral acceleration input is ceased. Such difference in frequency, would imply an underestimation of the number of loading cycles to which the infrastructure is subjected. On the other hand, the peak values are within acceptable difference levels.
The use of glass-fiber reinforced plastic (GRP) can reduce the weight of tanks significantly. By replacing steel with GRP in tanks for gases (propane, etc.) a weight reduction of up to 50 % was reached. In this project not only the material should be optimized, but also the design. Previous tanks consist of a double-walled structure with an insulation layer between the two shells (e.g. vacuum). Goal of this project is to realize a single-walled construction of GRP with an insulation layer on the outside.
To determine the temperature dependent material values, two different experiments are performed: In the first experiment, temperature dependent material properties of liquid nitrogen found in literature research are validated in a simple setup. The level of liquid nitrogen in a small jar is measured over the experiment time. Numerical simulation shows the change of nitrogen level with sufficient precision. In the second experiment, a liquid nitrogen is applied on one side of a GRP plate. Temperature is measured with thermocouples on top and bottom of the GRP plate, as well as in the middle of the plate. By use of numerical simulation, temperature dependent thermal conductivity is determined.
In the third experiment, a test stand is designed to examine different insulation materials. In this test stand, the insulation material can easily be changed. A numerical simulation, in which the determined material data is used, is performed as well for this test stand.
The experiments show, that GRP can be used in cryogenic environments. Multiphase simulations are a suitable tool to describe the energy absorption of thermal energy due to thermal phase change. Results on different insulation materials will follow.
Commidities and rail damage
(2018)
A roll-plane simplified model, representing the suspended body-cargo of a railway car, was developed to simulate thedynamic response of a railway car while subjectedto lateral acceleration derived from its traveling along curved tracks. The model provides the means to calculate the suspension forces, which are supposed to be transmitted to the bogie´s wheelset. For the analysis of the potential effect of such forces on the railway fatigue life, different performance measures were considered, under different concepts. A family of curves were produced to analyze the effect of the height of the center of gravity of the body-cargo system, on the different performance measures. The resultingdiagramswereused to assess the rail damage potentials offour different railway cars. Results suggest that the height of the center of gravity, associated to the different types of railway cars, nonlinearly and strongly affects the fatigue lifeof the rail, with the double stack car being the moreinfrastructure-aggressive. In this respect, experimental evidence should be provided about such remarkable effects, so as to supportsome operational recommendationsthat shouldbe taken to mitigate these effects, including, for example, the regulation of the traveling speed of some vehicles.