Angewandte Physik
Filtern
Erscheinungsjahr
- 2017 (131) (entfernen)
Dokumenttyp
- Vortrag (131) (entfernen)
Referierte Publikation
- nein (131) (entfernen)
Schlagworte
- Ageing (6)
- Composite (5)
- Spent fuel (5)
- Energy efficiency (4)
- P92 (4)
- Seal (4)
- Thermoelectrics (4)
- CO2 (3)
- Calcium cobaltite (3)
- Composite cylinder (3)
Eingeladener Vortrag
- nein (131)
The shock absorbing material damping concrete is for the foundation in dry interim storage facilities for radioactive waste in Germany. In case of a potential cask drop damping concrete minimizes the mechanical loads to the cask. In course of safety analyzes this accident scenario is considered by numerical simulations using the finite element method. To get reliable results of numerical simulations a suitable material model is needed to take the characteristics of damping concrete into account. Due to the lack of sufficient material knowledge a research project was started to characterize the material’s behavior under different load conditions. This paper presents the test program to analyze the material behavior of damping concrete which is characterized by large volume change and
strain rate hardening dependence. The determined Parameters were used to adapt an existing material model of the FE-code ABAQUS®. This model has to handle the mechanical damage behavior of damping concrete which occurs under compression and shear loads during a potential cask drop. To verify the material model numerical simulations are compared with dynamic penetration tests, which were conducted with specimens assembled similar to the real application of the damping concrete footings. The transferability of the material
model to a real accident scenario was verified by a drop test with a full-scale cask on a damping concrete footing.
Electric contacts based on silver-glass dispersions are key components in optoelectronic microsystems and control modules for medical, information & communication and energy technology in our networked society. Driven by the complexity of modern production processes and ever shorter time-to-market requirements, the fast and specific development of tailored silver-glass dispersions has become a bottleneck of technology development. Nevertheless, the underlying mechanisms of silver dissolution, transport, and reprecipitation, and the resulting micro structure evolution during firing are poorly understood. The broad literature on the precipitation of colloidal silver particles and the related processes of silver dissolution and diffusion mostly refer to very small volume fractions of silver. Transferring these results to the sintering of glass-containing silver dispersions, is therefore highly questionable. In this case, silver dissolution, electrical contact between silver particles, transport and reprecipitation take place under special conditions. This includes short diffusion lengths (particle size < 10 μm), the presence of three-phase contacts silver - glass - sintering atmosphere, as well as silver reprecipitation at the sintering contacts as the driving force of silver transport. Here, a dynamic balance of the silver concentration can be expected to result from the ratio between silver dissolution and reprecipitation. The aim of the project is to gain basic insight into the mechanisms of dissolution, transport and reprecipitation of silver in sintering silver glass dispersions. In this context, the main focus is on gaining basic knowledge about the dissolution of metallic silver in low melting oxide glasses as the limiting factor of the sintering of silver-glass composites. In particular, we will strive to gain insight into the effect of the oxygen content of the sintering atmosphere, of the oxygen dissolved in the silver particles, of silver oxide on the surface of the silver powder, of the electric contact between the silver particles, as well as the basicity of the glass. Furthermore, we strive for insights into the silver mobility and the silver concentration that can be attained (silver solubility) in oxide glasses with a low melting point. Summing up all these aspects, a closed explanatory model for silver dissolution, transport and reprecipitation during the sintering of glass silver dispersions will be introduced.
The presentation focuses on the latest developments of the German nuclear waste management policy including restructering of responsible organizations and the restart of the repository site selection process for high level radioactive waste.
The second part illustrates latest results of long term investigations of metal seals at BAM with regard to extended interim storage periods.
The presentation explains recent administrative developments in Germany concerning nuclear waste management and adresses national and European R&D funding concepts. National and international collaboration is explained followed by the latest update on long term metal seal investigations at BAM. Finally, fuel cladding failure mechanisms during long term dry storage and related R&D initiatives at BAM are explained.
The German nuclear waste management strategy consists of dry interim storage of spent fuel inside dual purpose casks and its subsequent direct final disposal in a deep geological repository. Interim storage is limited to 40 years so far, but will have to be extended until repository site selection and operation is concluded, potentially up to 100 years. In this context, research on the long term performance of safety relevant cask components and fuel rod integrity during such extended periods of time is of outmost importance. The barrier function of the fuel cladding depends on its integrity under operational and accidental conditions along with storage and subsequent transportation and is mainly affected over time by altering of the cladding microstructure and by thermo-mechanical conditions during reactor operation and subsequent wet and dry storage.
This paper focuses on failure mechanisms regarding cladding embrittlement caused by physical phenomena concerning hydrogen dissolution and precipitation of hydrides in the zirconium matrix. Within this context, potential cladding integrity issues under extended interim storage conditions followed by transportation are emphasized.
Delayed hydride cracking (DHC) is a well-known time-dependent temperature-activated phenomenon failure mechanism of the fuel cladding during reactor operation. The phenomenon consists of hydrogen diffusion and hydride precipitation at the tip of an initial crack and the propagation of the crack to an approximate distance equal to the length of the hydride. This failure mechanism is temperature-activated phenomenon and enhances along with thermal cycling of the fuel cladding, e. g. during reactor shutdowns. DHC shows limited relevance under quasi static storage conditions with continuously lowering temperatures. However, the literature points that DHC may occur when the temperature during storage decreases to a certain level after some decades and in combination with stress concentrations in the cladding material.
When spent fuel is transferred to dry storage by vacuum drying, the cladding temperature raises up to peak temperatures of ~370°C. Under these conditions, hydrides dissolute into the zirconium matrix up to the solubility limit defined by the peak temperature and this amount of hydrogen can precipitate in a radial re-oriented fashion due to the temperature decrease during storage. Cladding materials with radially precipitated hydrides show significant embrittlement. Radially oriented hydrides are perpendicularly oriented to hoop stresses representing the most critical configuration. Brittle failure of the cladding then occurs by crack propagation through radially oriented hydrides and finally through the zirconium matrix. The susceptibility to radial hydride precipitation depends on cladding material type and microstructure, hydrogen content, pre-drying hydride distribution, irradiation conditions, and temperature and stress histories during drying and storage operations.
This paper addresses major considerations concerning spent fuel cladding embrittlement due to hydride precipitation with regard to the boundary conditions of dry spent fuel storage in Germany. Analytical, numerical, and experimental approaches are to be discussed by BAM in order to identify the specific needs for future R&D work in that area with the purpose to provide the necessary data base for proper safety demonstration and evaluation along with future extended storage licensing procedures.
Influence of impact angle and real target properties on drop test results of cubic containers
(2017)
Drop test scenarios with cubic containers without impact limiters at interim storage sites or in a final repository have been investigated by numerical simulations. An ideally flat drop is impossible to conduct as a free fall of a container even under laboratory conditions. Dynamic stresses and strains inside the container structure are sensitive to the impact angle. Even very small impact angles cause remarkable changes in the experimental or numerical results when a flat bottom or wall of a container hits a flat target. For drop tests with transport packages the International Atomic Energy Agency (IAEA) regulations define an essentially unyielding target. In contrast, potential accident scenarios for storage containers are derived from site-specific safety analyses or acceptance criteria in Germany. Each interim storage site or repository has a yielding or so-called real target with individual structural and material properties. The real target acts as a kind of impact limiter. A more conservative container design is required if the impact limiting effect of the target is not considered.
Improving the energy efficiency of products was identified as the most important short-term opportunity to decrease energy consumption and therefore CO2-emission worldwide. More efficient products are created due to technical innovation. Restricting market access to efficient products only and making the most efficient products stand out by energy labelling are legislative tools to encourage this development. Market surveillance authorities’ checks are fundamental to protect the consumer from wrongly declared goods on the market and ensure fair competition between manufacturers. However, the activities of market surveillance authorities are limited by their financial resources. Testing all product efficiency parameters in an accredited laboratory is very time consuming and cost intensive. In this study, a theoretical concept is presented which can be used to develop screening tests in order to perform product tests by market surveillance authorities with less financial resources. The method identifies components which lead to non-compliance or make a product less energy efficient with minimum effort. The concept is based on a combination of random product tests, dismantling specific products and comparing components. This represents a new approach in product testing procedures beyond the current market surveillance activities. The concept is being tested within a research project funded by the German government.
Geothermal brine is considered to be an aggressive
environment as it contains various dissolved salts.
Even though carbon steel is commonly used as a
construction material due to its machinability and
economical reason, it is susceptible to uniform and
localized corrosion in a high temperature and high
pressure system. Therefore, a coating system is
introduced to protect the carbon steel against
corrosion in such environment.
1. Carbon steel is susceptible to uniform corrosion in presence of oxygen, with corrosion rate of immersion at 150 °C of 0.39 mm/a.
2. Exposure test of carbon steel at 150°C and 10 bar (pressurized by Ar) results in pitting corrosion with depth of 19 µm and width 4 µm on average.
3. OCP measurement shows that the stability of measurement is reached after 40 hours of immersion in the solution.
4. EIS measurement is useful to observe the effect of temperature, immersion time, and coating composition on the corrosion processes of coated metals for use in geothermal application.
A promising technology in photovoltaics is based on micro-concentrator solar cells, where the photovoltaic active area is realized as an array of sub-millimeter sized thin-film solar cells. For copper-indium-gallium-diselenide (CIGSe), the solar cells can be arranged in the foci of a regular arrangement of micro-lenses to enhance their efficiency by light concentration, to allow a better heat dissipation and to save expensive raw material (indium). Different approaches to produce micro-sized precursors of CIGSe absorbers on molybdenum are presented using 30-fs laser pulses at 790 nm wavelength. On the one hand, a multi pulse surface structuring of the molybdenum or the underlying glass substrate and a subsequent physical vapor deposition (PVD) process were used for a site-selective aggregation of indium droplets. On the other hand, a single pulse laser-induced forward transfer (LIFT) was utilized to selectively deposit combined copper/indium/gallium precursor pixels on the molybdenum back contact of the solar cell. It was demonstrated that a postprocessing (selenization, isolation, contacting) of the laser-generated micro-sized precursors results in an array of working CIGSe solar cells with an efficiency of 2.8% for 1 sun illumination.
An extraction of silica from natural sands of Bancar has been conducted by means of alkali fusion route using NaOH and mechanical alloying using planetary ball milling. The PANI/SiO2 Composite system has been coated in steel surfaces using spraying method. This study was designed to obtain PANI/SiO2 as an anti-corrosion coating material. The filler materials in the composite System consist of micro- and nano-SiO2. The structure of synthesized SiO2 be characterized using XRD and TEM. Corrosion of PANI/SiO2 composite has been tested using immersion method in synthetic geothermal atmosphere (Nord Deutsche Becken/NDB solution). The surface morphology after corrosion was observed by using SEM/EDX. XRD-Patterns and TEM show that the size of produced SiO2 is micro and nano. The size and composition of filler have influenced to surface degradation in geothermal atmosphere significantly. The addition of nano-SiO2 in the PANI matrix influenced corrosion resistance better than micro-SiO2 filler qualitatively. The nano-SiO2 has a high potential as an anti-corrosion material in geothermal atmosphere. The product of corrosion is mainly Fe2O3 and the corrosion process is identified as a pitting corrosion.
Vorstellung der Korrosionsuntersuchungen im Rahmen des Themenfeldprojektes LeBeWind an der BAM
(2017)
Im Vortrag wird das Teilprojekt Korrosion des Themenfeldprojektes LeBeWind vorgestellt. Dabei werden mit Blick auf die geltenden Regelwerke und Normen die Unterschiede verschiedener Prüfmethoden zur kathodischen Enthaftung bei organischen Beschichtungen vorgestellt und deren Aussagekraft kritisch betrachtet. Am Beispiel von systematischen Versuchsreihen an einem Kurzzeittest werden die Grenzen einiger Methoden herausgearbeitet und die Anwendbarkeit für Reparaturbeschichtungen in Offshore-Bereich hinterfragt. Zusätzlich werden die Problemstellungen bei der Versalzung von metallischen Oberflächen im maritimen und Offshore-Bereich betrachtet.
This presentation explains how the evaluation of technical requirements in regulations effects safety level. This shown by using the Monte-Carlo experiment consequently.
The first step is to explain how deterministic requirements and how probabilistic requirements work. Then the statistical behaviour of the generally unknown basic population can be described and that his behaviour is independent from the regulatory approach. Subsequently, the concept of evaluating sample test results with respect to deterministic requirements is explained. The item “acceptance rate” of the basic population that is behind each sample and behind each individuum in a sample is defined. On this collective understanding, the differences in evaluation between the probabilistic approach PA and the most important RC&S are discussed. Some areas are validated in contradictorily. Then the parameters for acceptance of burst strength in the UN-GTR#13 are varied and opens the door for an accurate improvement of acceptance criteria. Finally, the special aspects of degradation in load cycle testing are shown. There, two aspects must be differentiated, the current reliability and its degradation by ongoing load cycles. This is a convincing argument against the very common opinion, which means that the number of hydraulically tested load cycles pro-vides a figure for the number of acceptable filling cycles.
This presentation explains how an PA-based approval concept could work and would substitute the most of deterministic requirements based on a risk based quantification of accepted failure rates.
The concept of a probabilistic approval approach is based on 5 separate types of requirements:
1. Testing and evaluation of properties at Beginning of Life (BoL)
2. Artificial aging with residual strength assessment
3. Testing against dedicated accidental loads
4. Surveillance of production quality
5. Surveillance of degradation/ check of estimated end of life (EoL)
Each of these aspects is visualised by photos and diagrams.
This presentation explains how BAM operates the PA approach for the life-time surveillance based on the measurement of degradation.
The starting point is the sample performance chart (SPC) as developed by BAM. There it is possible to show minimum requirements, sample properties and lines of constant survival rates, these lines are called isoasfalia. The BAM provides a tool for the safety evaluation of results from sample testing. Then the interaction to the micro-mechanical approach of the FiBreMoD-project is linked with the idea of a degradation of strength and reliability. This leads to the methods of burst and cycle testing. For both methods examples are shown and degradation is explained by showing data of two design types. This visualise the determination of safe service life. Finally, statistical aspects of misinterpretation of test results and the reasons for the decision in favour of the slow burst tests are explained.
This presentation provides an impression of the boundary condition of the work on composite cylinders on a competent authority. It shows the various kinds of usage, the different tasks and duties around this kind of storage units and the wide spread of technical competence necessary for the substantial research when addressing the legislation. Based on this it shows how we react on changes in the regulations by research and how this influences the regulations, again. As an example, our probabilistic approach is mentioned and drafted for getting mentioned several times during the ongoing set of presentations.
Im Vortrag werden mit Blick auf die geltenden Regelwerke und Normen die Unterschiede verschiedener Prüfmethoden zur kathodischen Enthaftung bei organischen Beschichtungen vorgestellt und deren Aussagekraft kritisch betrachtet. Am Beispiel von systematischen Versuchsreihen an einem Kurzzeittest werden die Grenzen einiger Methoden herausgearbeitet und die Anwendbarkeit für Reparaturbeschichtungen in Offshore-Bereich ausgelotet.
A bottom-up approach to produce arrays of indium islands on a molybdenum layer on glass using 30-fs laser pulses at 790 nm wavelength is presented. These islands can serve as micro-sized precursors for indium compounds such as copper-indium-gallium-diselenide (CIGSe) used in photovoltaics. Molybdenum is the standard back contact material of CIGSe solar cells. Femtosecond laser ablation of glass and a subsequent deposition of a molybdenum film or direct laser processing of the molybdenum film both allow the preferential nucleation and growth of indium islands at the predefined locations in a following indium-based physical vapor deposition (PVD) process. A proper choice of laser and deposition parameters ensures the controlled growth of indium islands exclusively at the laser ablated spots. Based on a statistical analysis, these results are compared to the non-structured molybdenum surface, leading to randomly grown indium islands after PVD.
The development of competitive thermoelectric generators using oxide ceramics and multilayer technology requires the investigation of suitable sintering procedures. The sintering of Ca3Co4O9, which is the most promising p-type oxide regarding its figure of merit, is a special challenge, as the material starts to decompose at 926 °C. Pressure-assisted sintering (PAS), as known from large-scale production of low temperature co-fired ceramics, was used to sinter multilayers of Ca3Co4O9 green tape at 900 °C with different pressures and dwell times. In-situ shrinkage measurements, microstructural investigations and electric measurements were performed. Relative density increases from 57.4 % after free sintering for 24 h to 93.7 % after 2 h of PAS with 10 MPa axial load. The combination of tape casting and PAS induces a pronounced alignment of the anisotropic grains. In comparison to freely sintered multilayers, the electrical conductivity in the casting direction is thereby strongly increased by a factor of 5. With respect to dry-pressed bars, the improvement amounts to a factor of 15. This study shows that PAS is a proper technique to produce dense Ca3Co4O9 panels with good thermoelectric properties similar to hot-pressed tablets, even in large-scale production.
In this paper a shear test, which helps to study local behavior of the soil-pile interaction, is modelled numerically with the Finite Element Method as a 2D plane strain problem. A normal pressure on top and shear displacement on side were applied. So far, the material behavior was considered elastic for the sake of simplicity.
The effect of thickness on contact elements and the presence of in plane stress has been highlighted. The purpose of the paper is to find a suitable contact element which represents more close to reality a soil-pile interaction problem under cyclic axial loading. Moreover, an insight on the presence of in-plane stress shows that it needs to be considered cautiously.
Elastomer seals are widely used as barrier seals in containers for low and intermediate level radioactive waste. In addition, they are also used in waste fuel storage and transportation casks as auxiliary seals. Depending on the area of use, the rubber materials have to demonstrate proper sealing performance with respect to mechanical, thermal and environmental conditions as well as irradiation during the entire operation period. A fundamental understanding of the structure property relationship and their changes during aging can help to evaluate the long-term sealing performance.
In the present study, specific materials are investigated to study the structure-property and seal performance-correlation. Fluoro-elastomer (FKM), silicone rubber (VMQ) and ethylene propylene diene rubber (EPDM) were chosen as base rubbers. Comparable mechanical properties for these seals, especially in terms of a comparable compression behavior were achieved by careful control of base rubber formulation, i.e., by opting for the right filler and its concentration, amount of crosslinking chemicals, and with the assistance of process oils. Moreover, with the same rubber, similar mechanical properties were achieved by varying the filler concentration and crosslinking degree, which shall enable to correlate the particular influence on the structure property dependency of the seals in detail. The materials are investigated under pristine and aged conditions to evaluate the influence of aging, e.g. on the stress relaxation or recovery behavior. These values appear to be suitable parameters to judge the expected sealing performance.
Due to the electrically conducting nature of some fillers used to reinforce rubbers (such as carbon blacks, carbon nanotubes (CNTs), Graphene, etc.) it is possible to obtain current information about mechanical and visco-elastic properties by monitoring the electrical conductivity or resistivity. A simple relation that relates electrical resistance with mechanical stress was derived and the stress values were theoretically predicted from the electrical resistance values, which showed good correlation with experimental results.
Polymeric membranes represent a cost- and energy efficient solution for gas separation. Recently superglassy polymers with high free volume outperform many conventional dense polymers in terms of gas permeability and selectivity. However, such materials with a high fractional free volume (FFV) are prone to pronounced physical aging. The initial microporous structures approach a denser state via local chain rearrangements which results in a dramatic reduction in the gas permeability. For the first time, dielectric spectroscopy with state-of-the-art high-resolution analyzers was employed to investigate the molecular mobility and physical aging of two representative groups of superglassy polymers: PIMs (PIM-1 & PIM-EA-TB) and Si-containing polynobornenes (PTCNSi1 & PTCNSi2). The dielectric behavior of the solution-cast polymeric films was measured by isothermal frequency scans during the different heating cycles in a broad temperature range. Structural relaxation of the films was observed during the measurements. Multiple dielectric processes following Arrhenius behavior were observed for all the investigated polymers. Moreover, they all showed conductivity in the glassy state. The significant increase in the conductivity with increasing temperature especially for PIMs is explained in terms of the formation of local intermolecular agglomerated structures due to interaction of π-electrons in aromatic moieties of the polymer backbone.
The use of duplex stainless steels (DSS) in energy related applications is well known. Nowadays, DSSs become more favorable than austenitic steels due to the outstanding mechanical properties, the good corrosion resistance and the lower nickel content.However, the use of the duplex grade in acidic environments such as seawater can lead to a severe degradation in the structural integrity of the steel by hydrogen-induced/assisted cracking mechanisms, which can eventually result in premature failure. Hydrogen assisted degradation and cracking of steels remains unclear even though this topic is intensively studied for more than a century. The main gap lies in the validation of the proposed theoretical models at the sub-micron scale. Industrial and the research communities define a need for an accurate method by which it is possible to image the distribution of hydrogen in the microstructure. Among the very few available methods nowadays, Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS) provides precise mapping of hydrogen in the microstructure. Moreover, the powerful combination of ToF-SIMS with multivariate data analysis (MVA), electron backscattered diffraction (EBSD) for providing a the structural information and the use of data fusion techniques can contribute to a better understanding of the hydrogen induced degradation processes in the material.
In the present work two types of duplex grades were chosen as a case study (standard and lean DSS). The duplex class, consist of equivalent amounts of ferrite and austenite, was investigated by ToF-SIMS and EBSD during and after electrochemical deuterium charging in order to simulate the service of a component in acidic environments. Deuterium is known to act on the steel similarly to hydrogen and therefore was used as a tracer for hydrogen. The results show that the ferrite was affected almost identical in both steels whereas in the austenitic phase significant differences were observed in the lean duplex in comparison to the standard duplex. The advantage of the combined techniques is reflected by the ability to correlate the hydrogen distribution in the microstructure to the resulted structural changes.
Einfluss der Alterung auf dichtungsrelevante Eigenschaften von FKM-, VMQ- und EPDM-Elastomeren
(2017)
Da Elastomere in vielfältigen Dichtungsanwendungen eingesetzt werden und dabei teilweise großen Einfluss auf die Funktionsfähigkeit und Sicherheit haben, ist der Einfluss der Alterung auf dichtungsrelevante Eigenschaften relevant. Eine strukturierte Untersuchung des Einflusses von verschiedenen Mischungsrezepturen auf die Bauteileigenschaften, das Alterungsverhalten und die Funktion wird vorgestellt.
For many sealing applications rubbers are applied due to their special material properties and easy use. In many applications as e.g. in aviation, traffic or process technology the material can be exposed to low temperatures during operation. Therefore, it is important to know the material behaviour at those low temperatures to determine the temperature range that allows a safe operation of the seal.
In this work, we focus on the behaviour of elastomer seals at low temperatures with regard to potential decrease of leak-tightness or catastrophic seal failure of O-ring rubber seals. This is required as material properties of rubbers are strongly temperature dependent but their temperature application range is not always clearly defined.
Based on previous investigations which considered the physical material properties and the seal behaviour under purely static conditions we widen the focus on the sealing performance after a fast partial relief of compressed seals and additional materials.
For the investigations, different typical rubber seal materials were used as e.g. fluorocarbon (FKM), ethylene propylene diene (EPDM) and hydrogenated acrylonitrile-butadiene (HNBR) rubber.
The correlation of the physical material properties with seal performance is studied. This includes as well purely static sealing applications as the Performance during/after fast partial relief of seals at low temperatures.
CCUS-Technologie (CO2-Abtrennung; Nutzung und Speicherung, engl. Carbon Dioxide Capture, Utilization and Storage) gilt als eine vielversprechende Methode zur Abschwächung des Beitrags von fossilen Emissionen zur globalen Erwärmung. Dabei wird das in den Verbrennungsprozessen entstandene Treibhausgas aufgefangen, zu verschiedenen Lagerstätten transportiert und langzeitig gespeichert bzw. einer chemischen Nutzung zugeführt.
In bisher veröffentlichten Untersuchungen wurde gezeigt, dass die CO2-Transport-Pipelines in hohem Maße gefährdet sind, wenn sie korrosiven Begleitstoffen des CO2-Stroms, wie SOx, NOx bei einem hohen Wasserdampfanteil ausgesetzt sind. Screening-Tests zeigten, dass bei einer Konzentration von 1000 ppmv H2O die Reaktionen und Kondensation von SO2 und NO2 mit O2 und H2O zu Säuretropfen (pH ~ 0,5) auf der Oberfläche von Metall-Prüfkörper und Gefäß führen. Die Werkstoffe 1.0582, 1.8977, 1.4313 und 1.4562 wurden in CO2-gesättigtem Kondensat mit unterschiedlichem Verhältnis der säurebildenden Komponenten untersucht. Diese Studien zeigten grundsätzlich den Mechanismus sowie die Rolle jedes CO2-Strom-Begleitstoffes auf den Korrosionsprozess. Allerdings spiegeln die bei Auslagerung und elektrochemischen Messungen in der künstlichen CO2-gesättigten Kondensat-Lösung auftretenden Bedingungen nicht im Detail die Realität in der Praxis, wo sich nur Tröpfchen bilden, wider.
Diese Arbeit konzentriert sich auf den Korrosionsprozess von Kondensat in Form von Tröpfchen, auf der Oberfläche von Rohrleitungswerkstoffen unter CO2-Atmosphäre bei 5 °C (Simulation des Transportzustandes). Die Experimente wurden nicht nur für Auslagerungsversuche, sondern auch für elektrochemische Tests mit nur einem Tröpfchen (weniger als 20 µL) konzipiert. Die Auslagerungs-versuche wurden sowohl unter Normaldruck als auch bei hohem Druck (> 70 bar) durchgeführt, wobei das CO2 als dichte – den Tropfen umgebende - Phase vorliegt. Die korrodierten Prüfkörper wurden rasterelektronenmikroskopisch (REM) und mittels Energiedispersiver Röntgenspektroskopie (EDX) analysiert, um nicht nur Korrosionsform, sondern auch die Elementverteilung der Korrosionsprodukte zu zeigen.
Experimental determination and analysis of dynamic fracture toughness data of ductile cast iron
(2017)
Ductile Cast Iron materials (DCI) have become important structural materials. Neverthe-less, to draw maximum benefit from DCIs property potential, tailored testing methods must be provided. The established dynamic Jd-R and CTOD 5d-R curve procedures are based on material specifically developed, independent experimental techniques but pro-vide almost matching results. This can be seen as additional validation of the Jd procedure which was mandatory.
Elastomer seals are widely used as barrier seals in containers for low and intermediate level radioactive waste. In addition, they are also used in waste fuel storage and transportation as auxiliary seals. Depending on the area of use, the rubber materials have to demonstrate proper sealing performance with regard to mechanical, thermal and environmental conditions as well as irradiation during the entire operation period. A fundamental understanding of the structure property relationship can help to understand the performance of rubber seals in aged conditions. The present study focuses on the investigation of specific materials to study the structure-property and seal performance-correlation. Fluoro-elastomer (FKM), silicone rubber (VMQ) and ethylene propylene diene rubber (EPDM) were chosen as the prime candidates. Mechanical properties for these seals were achieved by careful control of base rubber formulation, i.e., by opting for the right filler and its concentration, amount of crosslinking chemicals, and with the assistance of process oils. Moreover, with the same rubber, similar mechanical properties were achieved by varying the filler concentration and crosslinking degree, which enables us to understand the structure property dependency of the seals in detail. The materials are investigated in the pristine and under aged conditions to evaluate the influence of ageing on e.g. the stress relaxation or recovery behavior. These values appear to be suitable parameters to judge the expected seal performance. Due to the electrically conducting nature of fillers used to reinforce rubbers (such as carbon blacks, carbon nanotubes (CNTs), Graphene, etc.) it is possible to obtain current information about mechanical and visco-elastic properties by monitoring the electrical conductivity or resistivity. A simple relation that bridges electrical resistance and the mechanical stress was derived and the stress values were theoretically predicted from the electrical resistance values, which showed good correlation with experimental results.
In recent years, the performance of heat resistant ferritic-martensitic steels under cyclic oxidation and cyclic mechanical loading has gained considerable attention. The growing contributions of renewable energy sources to electricity generation have triggered a shift from continuous (baseload) operation of conventional power plants towards cyclic or “flexible” operation, which is needed to stabilize the electric grids by balancing the highly variable renewable’s input.
Compared to the impressive amount of data on isothermal oxidation/corrosion and static
mechanical loading (creep) that was compiled over decades, only little and sometimes
contradictory information is so far available on the reaction of these alloys to cyclic
conditions. The latter may involve frequent transients or holds at intermediate temperatures, as well as shut-downs and start-ups with high temperature rates which result in cyclic mechanical loads (thermo-mechanical fatigue, TMF) and thermo-cyclic oxidation at variable temperature.
Our contribution will report on recent findings obtained within the framework of a junior
research group which investigates the oxidation and fatigue of the ferritic-martensitic grades P91, P92 and VM12 SHC under thermo-cyclic conditions. Cyclic oxidation tests are carried out in steam using different sample shapes (flat coupons, U-segments and rings taken from heat exchanger tubes). Special attention is paid to changes in the kinetics and the integrity and possible delamination/spalling of the oxide layers. Mechanical tests are carried out on material from real steam pipes with a focus on the softening behaviour and lifetime issues resulting from combined creep/TMF loadings. All experiments are carried out in the 300-620°C regime with temperature and load profiles that resemble typical loading scenarios in power plants and are complemented by detailed microstructural characterisation.
This work investigates the distribution of Chromium and Cobalt as well as other elements and their effect on the corrosion scale formation of ferritic-martensitic alloys under single and dual conditions. For this purpose, coupons of technical VM12-SHC alloy and model Fe-13Cr alloy were annealed at 600°C for 960 h in artificial flue gas. This kind of experiment represents the classical single condition corrosion test. To realize dual condition, an experimental setup was designed in such way that each face of the specimens could be in contact with a different atmosphere.
In this presentation the comparison between single and dual conditions will be evaluated in terms of phase composition of the scale and material loss. Preliminary results show clear deviations between both conditions in the distribution of chromium, as well as the diffusion outward of cobalt in the technical alloy.
This presentation provides general data about BAM, the structure of department 3 and a short impression of the application of pressure vessels for hydrogen in stationary use, supply chain and onboard storage.
It guides to the actions of BAM as competent authority on this area and shows a lot different methods for testing operated at BAM. Based on this additional research has been detected as necessary for a competent tackling of the tasks as competent authority. After having mentioned several important research projects a figure is presented that compares the development of regulations with relevant re-actions of BAM. The outcome was a concept of a risk based definition of accepted failure rates in combination with probability-oriented safety assessment over entire service life.
The second aspect raised at INERIS is the issue of advising the BMVI concerning pressure vessels for hydrogen. Since the pressure is high for saving material consumption and weight there is still high interest in changing regulatory requirements. Therefor we developed an approach for the display of minimum requirements of regulations in diagrams (sample performance charts; SPC) and the probabilistic analysis for these deterministic requirements. This is done by Monte-Carlo simulation and the analysis of acceptance rate and survival rate of basic populations all over the SPC.
This finally provide same knowledge of non-approvable but safe ranges of parameters and even approvable but non-safe constellations. In addition, this analysis allows to optimise deterministic requirements in regulations to the intended level of safety for approved populations of pressure vessels, which is shown on the example of the GTR#13.
This presentation mentions the most important safety items that should be improved from the perspective of Germany.
These are the improvement of the understanding and definition of term "safety", the agreement on procedures for the measurement of safety and the issue of degradation in combination with the safety level to be ensured until end of life.
For using probabilistic experience for the whole production adequate measures for surveillance of the production should additionally become mandatory to be taken into account.
The essential aspects of these issues are shortly explained and highlighted by especially aspects of the slow burst testing with respect to non-cycle fatigue sensitive designs and the hint on the general scatter of properties (Monte-Carlo simulation).
Measurements of downburst wind loading acting on an overhead transmission line in northern Germany
(2017)
Along an overhead transmission line in Northern Germany, a unique instrumentation of anemometers and force measurements is installed. Details of this test line with wind measurements along a horizontal axis are given. A recent event of a presumable downburst wind event is analyzed by means of available data and precedent works on thunderstorm analysis. The measured response of the conductors at the suspension tower is investigated and compared with time domain simulation of a finite element model.
Evaluation of test results
(2017)
Offshore wind energy towers are dynamically loaded by waves and wind. Pile foundations provide stiffness and damping and should be properly calculated. A combined finite-element boundary-element method for the dynamic interaction of flexible structures and the soil has been developed. The flexible structures such as single piles or complete wind energy towers are modeled by the finite element method whereas the homogeneous or layered soil is modeled by the boundary element method which uses the Green’s functions for interior loads in the layered half-space to establish the dynamic stiffness matrix of the soil. Soils with a stiffness that is continuously increasing with depth can be modeled as multi-layer soils with step-wise increasing stiffness. The effects of different parameters such as the stiffness of the soil, the axial and bending stiffness of the pile, and the radius of the cylindrical contact area will be analysed for the different components of excitation (vertical, horizontal, rotation and coupling). The results can be determined as specific power laws which are different for the different load cases and for the different soil models (Winkler support, homogeneous continuum, continuum with increasing stiffness). The dynamic effect of radiation damping will be analysed by the frequency-dependent compliance functions. A clear layering of the soil can cause noticeable changes in the dynamic compliances as reductions of the stiffness and the damping in certain frequency ranges (below and around layer resonance frequencies). The distribution of the displacements along the pile help to explain the observed laws. An example of an offshore wind energy tower has been modeled and calculated for wind, wave and weight loads. The resonances of the tower are usually limited by the radiation damping which is strongest for a soft soil.
Basics of statistic
(2017)
Accumulation of fibre breaks under time-dependent loads in CFRP materials of pressure vessels
(2017)
For the moment, there is no existing method to quantify the time-dependent effect on carbon fibre pressure vessels or composite pressure vessels (CPV) in general. Hence, BAM started to investigate how to proof this phenomenon. Several researches has been done and discovered that it is possible for aged pressure vessels to have higher burst pressure value than a new vessels. However, the scientific explanation behind is still an on-going research. Whether the existing model can be used or using another measurement method to gain more data is still in question. Therefore, it is required to find a suitable method to explain such phenomenon and even develop furthermore to give a strength criterion for certain types of pressure vessels
Compaction grouting involves the injection under high pressure of a highly viscous grout into the soil to displace and compact the surrounding soil without fracturing it. This ground improvement technique has been used widely for settlement control, increasing liquefaction resistance or bearing capacity of soil under new or existing structures. The work presented here aims to show some numerical and experimental investigations being carried out to understand the compaction mechanism and the soil-grout interaction, which is crucial for a successful usage of this technique.
To investigate compaction grouting in the laboratory under various stress conditions, a large-scale testing chamber has been developed. The grout was injected directly at the transparent vertical window of the chamber in order to investigate the possibility to monitor the injection process with a camera to measure the in-plane soil displacements and strains by means of the PIV technique. The other aim of this study is to develop a numerical model, which should be able to deal with large displacements and deformations and to simulate the change in shape of the distinct soil-grout interface solely as a result of the interaction between the injected grout and the surrounding soil. Based on these considerations, as a numerical technique, we employ the implicit Material Point Method based on a mixed formulation, which is implemented in the open source Kratos Multiphysics framework. In contrast to standard FE formulations, the usage of the MPM avoids both the numerical instability caused by extensive mesh distortion and the high computational costs of remeshing. The main results focus on the different evolution of the grout bulb inside the soil under various stress states.
Current trend suggests that global energy consumption will increase in the future. This growing energy demand and advancement of technology lead to explore all potential offshore fossil and non-fossil energy sources, necessitating erection of exploration and production structures, rigs, platforms and towers, which are susceptible to adverse environmental conditions along with their maintenances. Cylindrical grouted joints provide suitable connections between steel substructure and foundation in these offshore platforms and wind structures especially monopiles for ease of installation. However, these are composite connections with exterior sleeve, interior pile and infill grout. The capacity of these connections is affected by number of factors. The literature over last four decades by numerous researchers has shown the development of these connections with increasingly higher capacities and influences on these capacities due to various factors. This paper provides a comprehensive review on the factors affecting the connection capacity along with technical challenges for the future. Critical aspects and shortcomings of the current connection systems and potential solutions may be sought after for these issues are also discussed.
Application importance of ionizing radiation has been growing steadily over the last decades. Extensive utilization of ionizing radiation generates demand for development of suitable monitoring techniques. Radiation monitoring systems based on optical fibers offer several key advantages such as small footprint, possibility of remote and real-time measurement as well as electromagnetic immunity. In this contribution, we investigate radiation-induced attenuation (RIA)-based sensing with perfluorinated polymer optical fibers (PF-POFs). The RIA response of two commercial PF-POFs is assessed in a low dose region and performance and limitations of the system are discussed. The concept represents a potential high-sensitivity, low-cost and easy-to-use on-line radiation monitoring system with distributed detection capability.
Molecular sieves as materials with defined pores offer new opportunities in the preparation of nanostructured materials for different applications in chemistry, medicine and biology. Typical examples for such materials are zeolites, porous glass, different silicas and active carbon. Introducing transition metal ions in such materials can widen the possibilities of these materials in terms of chemical activity. Especially, the opportunity to tailor the redox properties of the transition metal ions by varying the location of the ion in the sieves is a promising way to obtain catalysts with the desired properties.
For this purpose, Cu2+ ions were introduced into a SAPO-5 (silicoaluminaphosphate) by a hydrothermal method and by impregnation. As expected, the different preparation methods led to different locations of the Cu2+ ions: by the hydrothermal method the ions were incorporated in the SAPO-5 framework, by impregnation mononuclear Cu species randomly distributed in the pores of the support or CuO particles were formed depending on the Cu amount. These locations could be determined by Extended X-ray Absorption Fine Structure and Anomalous Small-Angle X-ray Scattering investigations. For investigating the redox properties of the Cu2+ ions the differently prepared sample were treated in Ar and H2 atmosphere until 550°C. X-ray Photoelectron Spectroscopy was performed to study the valence states of Cu after each of such treatment. For a definite determination of the valence states, both Cu 2p and Cu LMM spectra must be recorded. Cu2+ exhibits a clear chemical shift and a typical satellite structure in Cu2p spectra, but between mono- and zerovalent Cu a differentiation is not possible. On the other hand, these two species show a clear shift in the Auger spectra. Whereas in H2 atmosphere in any case metallic Cu was formed, the treatment in Ar showed significant differences between the samples. Cu2+ incorporated in the framework could not be reduced by this treatment. In contrast, the mononuclear Cu2+ species were reduced to stable Cu+. Likewise, the CuO nanoparticles were reduced to the monovalent Cu, but this species can be much more easily reoxidized in air. The consequences for the catalytic properties will be discussed.
Fundamental understanding of crack healing in glassy crystalline materials is very important for solid oxide fuel cell (SOFC) sealants, since cracks caused by sealing or thermal cycling still remain a substantial bottleneck in developing durable SOFC.
Previous studies on soda lime silicate glass [Sin14] showed that crack healing is driven by viscous flow and that healing progress is proportional to time t and inverse viscosity η. This finding would allow to present healing data of a given glass for different temperatures in a master curve healing progress versus t/η. Such master curves would be a helpful tool in understanding crack healing kinetics.
Against this background, crack healing in non-crystallizing sodium calcium silicate (NCS) and sodium borosilicate glasses (NBS) have been studied. Moreover, to evaluate the influence of micro structure in crystallized glass on crack healing process, glass matrix composites (GMC) were prepared from NCS and zirconia as inert ceramic filler material mimicking a partially crystalline micro structure. By this way, the micro structure can be kept constant during crack healing. Cracks were generated by Vickers indention and healed isothermally at different temperatures. Crack healing progress was monitored by optical and electron microscopy. Results show that the above mentioned proportionality actually applies for the studied glasses for which such a master curve could be obtained. In comparison to a non-crystallized glass, the effective viscosity of GMC is increased by the rigid filler content. This effect substantially retards crack broadening during later healing stages, which often ends up in large pores. On the other hand, local viscous crack healing is still possible in larger glassy regions. This behavior seems to be very interesting for crack healing optimized micro structures.