Angewandte Physik
Filtern
Erscheinungsjahr
- 2020 (12) (entfernen)
Dokumenttyp
- Vortrag (9)
- Zeitschriftenartikel (3)
Schlagworte
- Wasserstoff (3)
- Sicherheit (2)
- Acceptance rate (1)
- Acoustic emission analysis (1)
- Akzeptanz (1)
- Approval (1)
- Batch testing (1)
- Bergungsdruckgefäß (1)
- Chance-risk analysis (1)
- Component testing (1)
- Composite cylinder (1)
- Distributed fiber optic sensing (1)
- Druck-Volumen-Produkt (1)
- Druckbehälter (1)
- F-N-diagram (1)
- Fibre break (1)
- Gas behaviour (1)
- Hybrid composite pressure vessel (1)
- Hydrogen (1)
- Hydrogen vehicles (1)
- Impact (1)
- Inspection (1)
- Kompetenzzentrum H2Safety@BAM (1)
- Konsequenzbegrenzung (1)
- Lebensdauervorhersage (1)
- Limit of acceptable consequence (1)
- Material properties and compatibility (1)
- Mean burst pressure (1)
- Minimum burst pressure (1)
- Minimum burst ratio (1)
- Monte-Carlo (1)
- Monte-Carlo Simulation (1)
- Monte-Carlo-Experiment (1)
- Multiscale model (1)
- Population (1)
- Pressure Vessel (1)
- Pressure-volume product (1)
- Probabilistic (1)
- Production scatter (1)
- Reduced volume method (1)
- Regulations (1)
- Safe handling (1)
- Safety (1)
- Safety Assessment (1)
- Safety assessment (1)
- Sample performance chart (1)
- Sensors (1)
- Sicherer Umgang (1)
- Statistische Bewertung (1)
- Structural health monitoring (1)
- Transport of dangerous goods (1)
- Type IV pressure vessels (1)
- UN-Modellvorschriften (1)
- Volumenbegrenzung (1)
- Wasserstoffspeicher (1)
- Wasserstoffstrategie (1)
Organisationseinheit der BAM
- 3.5 Sicherheit von Gasspeichern (12) (entfernen)
Eingeladener Vortrag
- nein (9)
First the acceptance rates resulting from the analysis of different minimum burst ratios and standards are displayed and explained. Especially the problems resulting from a further reduction if the minimum burst ratio are shown.
For a better understanding of these results the process of analysing the acceptance rate is explained in detail. This contains the alleged contradiction between safety of samples due to its scatter while the rejected sample provides a higher mean strength.
Then the importance of batch testing is explained and leads to the recommendation to have a strong interaction between provided mean strength and requested maximum of production scatter.
The stacking sequence of a real scale type IV pressure vessels has been found. Feasibility study of a multiscale model has been carried out by modifying the original stacking sequence. All of the results were displayed in a Sample Performance Chart (SPC), where different burst pressure in terms of mean and scatter had been found.
Composite pressure vessels (CPVs) are becoming the state of the art for storage for compressed hydrogen (CH2) in automotive applications. There is a strong interest of car manufacturers to use lightweight and less-costly gas storage units. In order to reduce the necessary amount of expensive carbon fibre, the nominal safety margins are becoming gradually smaller, pushing the limits of the regulations for type approval. At the same time, the total volume of these vessels increases to extend the range of the vehicles, increasing the consequences for worst-case scenarios like the rupture of the CPVs in service.
This presentation presents insights gained in the project “TAnk HYdrogen Automotive” (TAHYA). Its aim is to improve the safety of current regulations for type approval of pressure vessels for the use in hydrogen fueled vehicles, namely GTR No. 13 and ECE R 134.
For the assessment of safety, the probabilistic approach developed by division 3.5 of BAM is used. Monte-Carlo-Simulations were conducted leading to the identification of several weak spots, mainly found in the burst test and the batch test.
By changing the requirements for burst tests and the approach for batch tests, the identified weak spots can be strongly reduced.
In the DECHEMA Virtual Talks, general aspects of the safety and acceptance of hydrogen technologies were presented. How can trust in new technologies be built when past accidents led to myths and fairy tales? The presentation does away with general prejudices and shows that handling hydrogen is neither more unsafe nor safer than handling other fuel gases. The basis for the safe handling of hydrogen is always a risk analysis.
Safety criteria for the transport of hydrogen in permanently mounted composite pressure vessels
(2020)
The recent growth of the net of hydrogen fuelling stations increases the demands to transport compressed hydrogen on road by battery vehicles or tube-trailers, both in composite pressure vessels. As a transport regulation, the ADR is applicable in Europe and adjoined regions, and is used for national transport in the EU. This regulation provides requirements based on the behaviour of each individual pressure vessel, regardless of the pressure of the transported hydrogen and relevant consequences resulting from generally possible worst case scenarios such as sudden rupture. In 2012, the BAM (German Federal Institute for Materials Research and Testing) introduced consequence-dependent requirements and established them in national transport requirements concerning the “UN service life checks” etc. to consider the transported volume and pressure of gases. This results in a requirement that becomes more restrictive as the product of pressure and volume increases. In the studies presented here, the safety measures for hydrogen road transport are identified and reviewed through a number of safety measures from countries including Japan, the USA and China. Subsequently, the failure consequences of using trailer vehicles, the related risk and the chance are evaluated. A benefit-related risk criterion is suggested to add to regulations and to be defined as a safety goal in standards for hydrogen transport vehicles and for mounted pressure vessels. Finally, an idea is given for generating probabilistic safety data and for highly efficient evaluation without a significant increase of effort.
We present the results of distributed fiber optic strain sensing for condition monitoring of a hybrid type IV composite fully wrapped pressure vessel using multilayer integrated optical fibers. Distributed strain sensing was performed for a total number of 252,000 load cycles until burst of the vessel. During this ageing test material fatigue could be monitored and spatially localized. Critical material changes were detected 17,000 cycles before material failure. Results have been validated by acoustic emission analysis.
Der Vortrag beginnt mit dem erwarteten Bedarf an Wasserstoff und der Frage der Risikosteuerung bei stattfindender Marktdurchsetzung. Dem gegenüber ist an einem Beispiel der Prozess der Regelsetzung gestellt, was die Notwendigkeit pro-aktiven Handelns zeigt.
Es wird über die risikobasierte Definition von Sicherheit gezeigt, welche Bedeutung die Erfassung der Fertigungsstreuung hat und wie die quantitative Erfassung und Bewertung aussehen könnte. Zuletzt wird über den Aspekt der Alterung auf das Potential probabilistischer Zulassungsansätze verwiesen und aufgezeigt, wie die Wirkung von Vorschriften nach dem probabilistischen Sicherheitskriterium bewertet und optimiert werden kann.
Das Thema Wasserstoff ist an der BAM seit mehr als hundert Jahren aktuell und steht auch gegenwärtig im Zentrum zahlreicher Forschungs- und Kooperationsaktivitäten. Mit der aktuellen Wasserstoff-Strategie der BAM werden wichtige Voraussetzungen dafür geschaffen, dass der Markthochlauf gelingt und die technische Sicherheit und Überwachung der Infrastrukturen und Anlagen gewährleistet ist – von der Erzeugung, über den Transport bis zur Speicherung und Bereitstellung von Wasserstoff als Energieträger der Zukunft.
Hydrogen is an attractive energy carrier that requires high effort for safe storage. Forensuring safety, they must undergo a challenging approval process. Relevant standardsand regulations for composite cylinders used for the transport of hydrogen and for its on-board storage are currently based on deterministic (e.g. ISO 11119-3) or semi-probabilistic(UN GTR No. 13) criteria. This paper analysis the properties of such methods withrespect to the evaluation of load cycle strength. Their characteristics are compared withthe probabilistic approach of the BAM. Based on Monte-Carlo simulations, the availabledesign range (mean value and scatter of strength criteria) of current concepts was exem-plarily estimated. The aspect of small sample sizes is analysed and discussed with respectto the evaluation procedures.
The presentation starts with some key figures about BAM. Then it introduces BAM's competence centre H2Safety@BAM and shows aspects of special competence of the centre. It closes with information about the engagement of BAM in European research projects on hydrogen and a reference to our bilingual paper about our hydrogen strategy.