Angewandte Physik
Filtern
Dokumenttyp
- Vortrag (37)
- Zeitschriftenartikel (13)
- Beitrag zu einem Tagungsband (5)
- Posterpräsentation (3)
- Buchkapitel (1)
Sprache
- Englisch (59) (entfernen)
Schlagworte
- Hydrogen (13)
- LH2 (10)
- Safety (10)
- H2Safety@BAM (9)
- Lithium-ion battery (7)
- Release (7)
- BLEVE (5)
- Explosion protection (5)
- Consequences (4)
- Electrical Energy Storage (4)
Organisationseinheit der BAM
- 2 Prozess- und Anlagensicherheit (59) (entfernen)
Paper des Monats
- ja (1)
Eingeladener Vortrag
- nein (37)
The introduction of hydrogen as a safe energy carrier needs a robust knowledge base, tools for the design and safety assessment of hydrogen technologies built on it, and an internationally harmonized set of standards and regulations. Many of the innovative technologies imply hydrogen at high pressures and/or cryogenic temperatures, with which private users come into contact for the first time in distributed applications. In order to avoid over-conservative, expensive safety solutions, while at the same time demonstrating the usability and safety of hydrogen applications and maintaining acceptance for the technology, safety research must also keep pace with, or better yet anticipate, trends in technological development. Thus, this overview article describes not only the current state of knowledge and technology regarding hydrogen safety, but also its further development.
In order to reduce the human footprint of CO2 emissions and limit global warming effects hydrogen combustion is becoming increasingly important. To enable fuel cells and gas turbines to operates this carbon free fuel, unprecedently large amounts of hydrogen need to be produced and safely transported and stored. The investigation of the effects of accidents involving hydrogen is therefore becoming of outmost importance. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the release of hydrogen from a leakage with subsequent ignition. The resulting jet flame must be characterized with respect to the thermal radiation emitted into the environment to define safety regulations. Various models that characterize the resulting flame shape and radiation already exist in the literature, but these are mainly based on empirical data from hydrocarbon jet flames.[1-4] To verify these models, a H2 Jet Flame project conducted at BAM, is investigating the safety of momentum driven hydrogen jet flames. For this purpose, large-scale tests are carried out at the Test Site Technical Safety (BAM-TTS). The object of the investigations is to assess the effects of real scale release scenarios regarding flame geometry and the thermal radiation emitted. Parameters such as release angle, leakage diameter (currently 1 mm to 10 mm), pressure (currently up to max. 250 bar) and mass flow (up to max. 0.5 kg/s) are varied. In addition, influences such as the type of ignition, ignition location as well as delayed ignition can also be investigated. The gained knowledge will be compared with existing jet flame models, to validate these and identify a possible need for further development. In particular, the focus will be laid on the thermal radiation of hydrogen flames. The challenge here is the visualization and characterization of the flame geometry in an open environment. Visualization is performed using infrared (IR) camera systems from at least two viewing angles. Measurements of the heat radiation of jet flames, which can be found in the literature, are mostly based on unsteady outflow conditions. The experimental setup used here allows for the generation of a steady-state outflow for several minutes and thus a direct comparability with existing (steady-state) models. Furthermore, the tests can be carried out for comparative measurements with hydrocarbons (methane, etc.) as well as mixtures of hydrogen and hydrocarbons.
In order to reduce the human footprint of CO2 emissions and limit global warming effects hydrogen combustion is becoming increasingly important. To enable fuel cells and gas turbines to operates this carbon free fuel, unprecedently large amounts of hydrogen need to be produced and safely transported and stored. The investigation of the effects of accidents involving hydrogen is therefore becoming of outmost importance. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the release of hydrogen from a leakage with subsequent ignition. The resulting jet flame must be characterized with respect to the thermal radiation emitted into the environment to define safety regulations. Various models that characterize the resulting flame shape and radiation already exist in the literature, but these are mainly based on empirical data from hydrocarbon jet flames.[1-4] To verify these models, a H2 Jet Flame project conducted at BAM, is investigating the safety of momentum driven hydrogen jet flames. For this purpose, large-scale tests are carried out at the Test Site Technical Safety (BAM-TTS). The object of the investigations is to assess the effects of real scale release scenarios regarding flame geometry and the thermal radiation emitted. Parameters such as release angle, leakage diameter (currently 1 mm to 10 mm), pressure (currently up to max. 250 bar) and mass flow (up to max. 0.5 kg/s) are varied. In addition, influences such as the type of ignition, ignition location as well as delayed ignition can also be investigated. The gained knowledge will be compared with existing jet flame models, to validate these and identify a possible need for further development. In particular, the focus will be laid on the thermal radiation of hydrogen flames. The challenge here is the visualization and characterization of the flame geometry in an open environment. Visualization is performed using infrared (IR) camera systems from at least two viewing angles. Measurements of the heat radiation of jet flames, which can be found in the literature, are mostly based on unsteady outflow conditions.The experimental setup used here allows for the generation of a steady-state outflow for several minutes and thus a direct comparability with existing (steady-state) models. Furthermore, the tests can be carried out for comparative measurements with hydrocarbons (methane, etc.) as well as mixtures of hydrogen and hydrocarbons.
The combustion characteristics and explosive hazard of syngas (H2/CO)/air mixtures are affected by its exact composition and equivalence ratios. In this paper, the explosion pressure and spectral radiant intensity of free radicals were quantitatively examined for syngas with different H2 proportions ([H2 in syngas] = 0, 30, 50, 70, 100 vol%) and equivalence ratios (φ = 0.8, 1.0, 1.2, 1.4, 1.6, 2.0, 2.5). The results show that the explosion process of syngas/air mixtures can be separated into the initial slow combustion stage, the violent deflagration stage and the deflagration ending stage. The peaks of explosion pressure, pressure rise rate, OH*spectral intensity and rise rate of spectral intensity first increase and then decrease with increasing the equivalence ratio, and they reduce gradually with the decrease of H2 proportion in syngas. The H2 content in syngas greatly affects the heat release and the concentration of excited state OH*, especially for the syngas/air mixtures with smaller proportion of H2. Additionally, the presence of H2 greatly increases the deflagration index and spectral radiant index of OH* for syngas/air mixtures. The average rise rates of explosion pressure and spectral intensity of free radicals are introduced and the coupling model between them is established based on the first law of thermodynamics and the principle of chain reaction. The established model is furthermore verified by the experimental results. It is indicated that there is a linear relationship between average rise rates of explosion pressure and spectral intensity (OH*). The results can be used to improve the combustion efficiency of syngas and to guide theoretically the prevention, mitigation and control of syngas explosions.
In order to reduce global warming, the use of hydrogen as a renewable energy source is becoming more important. To enable this transition, unprecedently large amounts of hydrogen need to be safely transported and stored. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the release of hydrogen from a leakage with subsequent ignition. The resulting jet flame must be characterized with respect to the thermal radiation emitted into the environment to define safety distances. Various models that characterize the resulting flame shape and radiation already exist in the literature, but these are mainly based on empirical data from hydrocarbon jet flames. To verify the applicability of these models to hydrogen, real-scale tests are carried out at the BAM Test Site for Technical Safety (BAM-TTS) with the aim to assess the flame geometry and the emitted thermal radiation. Parameters such as leakage diameter (currently up to 30 mm), pressure (currently up to max. 250 bar) and mass flow (up to max. 0.5 kg/s) are varied. In particular, the focus will be laid on the measurement and modelling of the thermal radiation. The challenge here is the characterization of the flame geometry in an open environment and its impact on the thermal radiation. Existing heat radiation data from literature are mostly based on unsteady outflow conditions. The experimental setup used here allows for the generation of a steady-state outflow for several minutes and thus a direct comparability with existing (steady-state) models. Furthermore, stationary outflow tests with hydrocarbons (methane) were also carried out, which are intended to serve as reference tests for checking flame models based on hydrocarbon data. Following from the experimental investigations, modelling parameters such as the Surface Emissive Power (SEP) and the radiant heat fraction for hydrogen and methane will be compared to literature data.
Germany has concluded energy partnerships with various countries, including Japan. During the 3rd meeting of the Hydrogen Working Group, the strategic approach of both countries on developments of hydrogen guidelines, certification and safety was presented and discussed. BAM gave a presentation on important topics in the field of safety research and on safety-related issues along the value chain. Furthermore, the work program and selected projects of the competence center H2Safety@BAM were presented.
A safe supply of energy is a fundamental prerequisite for modern industrial societies. The extent to which the energy turnaround is being shaped in Germany in terms of, for example, energy policy, promotion, but also social development was discussed during the 12th Wildau Science Week. BAM contributed to the topic of safety of energy sources and presented the competence center H2Safety@BAM.
The Gases Advisory Group is organized regularly by the Prevention Division of the German Employer's Liability Insurance Association for Raw Materials and the Chemical Industry. The event serves as an exchange between science and industry on current safety-related issues concerning oxygen and hydrogen. In this context, BAM presented an overview of its various activities of the competence center H2Safety@BAM, which are reflected in the entire hydrogen value chain. In addition, the plans for the expansion of the test infrastructure at BAM's Technical Safety Test Site were presented. The results of the DELFIN project on the safety of pressurized gas storage tanks, the release tests of liquid hydrogen as well as the underfiring of corresponding cryogenic storage tanks and the plans for the ModuH2Pipe@BAM project were also presented. The presentation concluded with the current recommendations of the Hydrogen Research Network.
Hydrogen is a central component of the energy transition and the European Green Deal for a climate-neutral Europe. To be able to achieve the targets defined by 2045, the EU and the German government have drafted a framework for action and are making long-term investments in research, development and the rapid implementation of innovative hydrogen technologies.
The conditions for a successful energy transition and the economic use of green hydrogen as a clean energy carrier are Hydrogen readiness and a rapid market ramp-up, as well as the establishment of the necessary value chains in the national and European framework. Reliable quality and safety standards are the prerequisite for ensuring safety of supply and environmental compatibility and for creating trust in these technologies.
BAM has bundled its expertise in the field of hydrogen technologies into a competence center H2Safety@BAM to create confidence in the technology and to support the hydrogen strategies of the German government and the EU. The topic of hydrogen has been current at BAM for more than one hundred years and is also currently the focus of numerous research and cooperation activities. The competence centre H2Safety@BAM and its vision of “We build trust in hydrogen technologies” will be presented with its many safety-related topics, which can be found throughout the entire hydrogen value chain. Two deep dives will present the results on projects dealing with the design-to-cost issue of classical pressurized gas storage containments and the consequences of the release of liquid hydrogen, which will be roughly compared to the release of ammonia.