Angewandte Physik
Filtern
Erscheinungsjahr
- 2017 (44) (entfernen)
Dokumenttyp
Referierte Publikation
- ja (44) (entfernen)
Schlagworte
- Rubber (3)
- Cytop (2)
- Drop test (2)
- Electron backscatter diffraction (2)
- Finite element method (2)
- Radiation-induced attenuation (2)
- Simulation (2)
- ToF-SIMS (2)
- Accelerated ageing (1)
- Aerodynamic damping (1)
Drop testing of a container for the storage. transport and disposal of intermediate level waste
(2017)
Impact tests were performed, as part of a corresponding container’s substantiation, during design development of a shielded container. The container will be used for storage, transport, and disposal of intermediate level waste in the UK.
The mechanical test program comprised a 9m free drop test onto an unyielding target in a container long lid edge down orientation at ambient conditions. Further, a 0,5m free drop test onto a punch target was performed. Here, the container was orientated with the lid downwards in a way that the punch, a mild steel bar, impacts a filter lid.
The test specimen was instrumented with strain gauges and accelerometers for the drop tests. Transient strains at selected points of the inner and outer container walls, at the shielding lid, as well as at the lid bolts were measured during the container’s impact. Furthermore, decelerations of the container body, container lid, and the skip were measured. The complex geometrical changes of the container due to impact were determined by optical 3d- deformation measures using the projected fringes method in combination with multi-image photogrammetry.
This paper summarizes the performance of the drop tests and various drop test results in context with the design development as well as aspects regarding the associated Finite Element (FE) analyses and post-test evaluation.
The shock absorbing material damping concrete is for the foundation in dry interim storage facilities for radioactive waste in Germany. In case of a potential cask drop damping concrete minimizes the mechanical loads to the cask. In course of safety analyzes this accident scenario is considered by numerical simulations using the finite element method. To get reliable results of numerical simulations a suitable material model is needed to take the characteristics of damping concrete into account. Due to the lack of sufficient material knowledge a research project was started to characterize the material’s behavior under different load conditions. This paper presents the test program to analyze the material behavior of damping concrete which is characterized by large volume change and
strain rate hardening dependence. The determined Parameters were used to adapt an existing material model of the FE-code ABAQUS®. This model has to handle the mechanical damage behavior of damping concrete which occurs under compression and shear loads during a potential cask drop. To verify the material model numerical simulations are compared with dynamic penetration tests, which were conducted with specimens assembled similar to the real application of the damping concrete footings. The transferability of the material
model to a real accident scenario was verified by a drop test with a full-scale cask on a damping concrete footing.
Creep behavior of a γ΄-strengthened Co-base alloy with zero γ/γ΄-lattice misfit at 800 °C, 196 MPa
(2017)
Deformation and structural behavior of an experimental γ΄-strengthened Co-base alloy during creep at 800 °C and 196 MPa have been investigated. The characteristic features of this alloy are zero γ/γ΄-lattice misfit and a fine γ/γ΄-microstructure. In the initial condition, the γ΄-precipitates in this alloy are small (size of about 100 nm), have polyhedral morphology, and are separated by the very narrow c-channels (width of about 10 nm). The tests performed up to about 1% creep strain (about 500 h creep time) gave creep curves with a slow constant strain rate and without an apparent transient creep, typical for superalloys with nonzero misfit. In this initial stage of creep, entering of the narrow γ-channels by dislocations is blocked by a strong Orowan force. The micromechanism of creep was identified as an octahedral glide of h011i superdislocations simultaneously in two phases, γ and γ΄. The γ/γ΄-microstructure with zero misfit shows no rafting but rapidly coarsens isotropically. It is concluded that zero misfit is beneficial at the initial stages of the creep but is unfavourable for longterm creep because of the continuous microstructural coarsening.
The experimental density data of the binary System nitrogen−hydrogen available at the time of the development of the equation of state for natural gases and related mixtures, GERG-2008, were limited to hydrogen contents higher than 0.15 (amount-of-substance fraction) and temperatures above 270 K. This work provides accurate experimental (p, ρ, T) data for three binary mixtures of nitrogen and hydrogen: (0.95 N2 + 0.05 H2), (0.90 N2 + 0.10 H2), and (0.50 N2 + 0.50 H2) at temperatures of 240, 250, 260, 275, 300, 325, and 350 K, thus extending the range of available experimental data to low hydrogen contents and low temperatures. The density measurements were performed by using a single-sinker densimeter with magnetic suspension coupling at pressures up to 20 MPa. Experimental data were compared with the corresponding densities calculated from the GERG-2008 and the AGA8-DC92 equations of state. The relative deviations of the experimental data from both equations of state were within the estimated uncertainty value of the equations. Therefore, the experimental data agree very well with the values estimated from the equations. The virial coefficients B(T,x), C(T,x), and D(T,x) as well as the second interaction virial coefficient B12(T) for the nitrogen−hydrogen binary system were also calculated from the experimental data set at temperatures from 240 to 350 K. The resulting values agree with those from literature.
Influence of impact angle and real target properties on drop test results of cubic containers
(2017)
Drop test scenarios with cubic containers without impact limiters at interim storage sites or in a final repository have been investigated by numerical simulations. An ideally flat drop is impossible to conduct as a free fall of a container even under laboratory conditions. Dynamic stresses and strains inside the container structure are sensitive to the impact angle. Even very small impact angles cause remarkable changes in the experimental or numerical results when a flat bottom or wall of a container hits a flat target. For drop tests with transport packages the International Atomic Energy Agency (IAEA) regulations define an essentially unyielding target. In contrast, potential accident scenarios for storage containers are derived from site-specific safety analyses or acceptance criteria in Germany. Each interim storage site or repository has a yielding or so-called real target with individual structural and material properties. The real target acts as a kind of impact limiter. A more conservative container design is required if the impact limiting effect of the target is not considered.
The development of organic coatings for corrosion protection is an elaborate process with a multitude of often interminable investigations and tests of protection properties. Electrochemical methods support the processes of development to a great extent and help to understand mechanisms of action and failure. They are usually carried out on applied coating systems with a completed formulation. An examination possibility is presented in this publication that enables the characterization of waterbased coatings with different formulation variations in the liquid (aqueous) state with the aid of electrochemical noise technique. Thus, selection of binders, pigments, and other additives is supported essentially and made more efficient in a very early Phase of formulation development. The paper shows that a unique insight into the dynamic processes of a metal in contact with an aqueous coating dispersion is possible using the example of the development of zinc-free corrosion-inhibiting pigments for waterbased coatings. In addition, it is presented in which way the results correlate with the performance of applied coatings.
Environmental and sustainable economical concerns are generating a growing interest in biofuels predominantly produced from biomass. It would be ideal if an energy conversion device could directly extract energy from a sustainable energy resource such as biomass. Unfortunately, up to now, such a direct conversion device produces insufficient power to meet the demand of practical applications. To realize the future of biofuel-fed fuel cells as a green energy conversion device, efforts have been devoted to the development of carbon-based nanomaterials with tunable electronic and surface characteristics to act as efficient metal-free electrocatalysts and/or as supporting matrix for metal-based electrocatalysts. We present here a mini review on the recent advances in carbon-based catalysts for each type of biofuel-fed/biofuel cells that directly/indirectly extract energy from biomass resources, and discuss the challenges and perspectives in this developing field
The EU Ecodesign and Energy Labelling Directives set regulations on the energy efficiency, environmental, and information requirements of energy related products entering the EU market. Each individual product regulation stipulates that the EU Commission must undertake a review after a certain number of years. This review stage is crucial to improve the effectiveness and ambition of regulations, and also presents an opportunity to include new resource efficiency aspects. The strength of a review depends on the review process, which has followed various approaches in each reviewed product group so far. This article aims to summarise and discuss these varying review processes and identify their differences and shortcomings. The analysis is based on comparing the review processes to the standard Methodology for Ecodesign of Energy related Products (MEErP) used in preparatory studies to develop new Ecodesign regulations. Analysis questions were discussed with a small number of experts to gain deeper insights on opportunities and difficulties; suggestions are made for improving future review processes.
We investigate the dynamics of semiconductor lasers subject to time-delayed optical Feedback from the perspective of dynamical self-injection locking. Based on the Lang-Kobayashi model, we perform an analysis of the well-known Low Frequency Fluctuations (LFFs) in the frequency-intensity plane. Moreover, we investigate a recently found dynamical regime of fragmented LFFs by means of a locking-range analysis, spectral comparison and precursor pulse identification. We show that LFF dynamics can be explained by dynamical optical injection locking due to the delayed optical feedback. Moreover, the fragmented LFFs occur due to a re-injection locking induced by a particular optical pulse structure in the chaotic feedback dynamics. This is corrobo-rated by experiments with a semiconductor laser experiencing delayed feedback from an optical fiber loop. The dynamical nature of the feedback injection results in an eventual loss, but also possible regaining, of the locking, explaining the recently observed phenomenon of fragmented LFFs.
Discoloration Effects of High-Dose gamma-Irradiation and Long-Term Thermal Aging of (U) HMW-PE
(2017)
Two polyethylene types with ultra-high (UHMWPE) and high molecular weight (HMW-PE) used as neutron radiation shielding materials in casks for radioactive waste were irradiated with doses up to 600 kGy using a 60Co gammasource. Subsequently, thermal aging at 125∘C was applied for up to one year. Degradation effects in the materials were characterized using colorimetry, UV-Visspectroscopy, IR spectroscopy, and DSC. Both materials exhibited a yellowing upon irradiation.The discoloration of UHMW-PE disappeared again after thermal aging.Therefore, the yellowing is assumed to originate fromannealable color centers in the formof free radicals that are trapped in the crystalline regions of the polymer and recombine at elevated temperatures. For the antioxidantcontaining HMWPE, yellowing was observed after both irradiation and thermal aging. The color change was correlated mainly to decomposition products of the antioxidant in addition to trapped radicals as in UHMW-PE. Additionally, black spots appeared after thermal aging of HMW-PE.