Angewandte Physik
Filtern
Erscheinungsjahr
- 2016 (41) (entfernen)
Dokumenttyp
Sprache
- Englisch (41)
Referierte Publikation
- ja (41) (entfernen)
Schlagworte
- Gas storage areas (4)
- Membrane-based gas sensing (4)
- Subsurface monitoring (4)
- Distributed sensor (3)
- NDT (3)
- Computed tomography (2)
- Cytop (2)
- Distributed linear sensor (2)
- GERG-2008 equation of state (2)
- Linear sensor (2)
This work provides accurate experimental (p, rho, T) values for three binary mixtures of methane with helium: (0.95 (amount-of-substance fraction) CH₄+ 0.05 He) and (0.90 CH₄+ 0.10 He) at temperatures of (240, 250, and 260) K and (0.50 CH₄+ 0.50 He) from (240 to 400) K. This work is a continuation of a previous one which reported accurate experimental (p, rho, T) values for the (0.95 CH₄+ 0.05 He) and the (0.90 CH₄+ 0.10 He) binary mixtures over the temperature range from (250 to 400) K. All density measurements were performed by using a single-sinker densimeter with magnetic suspension coupling at pressures up to 20 MPa. Experimental values were compared with the corresponding densities calculated from the GERG-2008 and the AGA8-DC92 equations of state, respectively. Deviations from the GERG-2008 are much larger than from the AGA8-DC92 (up to -6.5%). These deviations increase with decreasing temperature, with increasing pressure, and with increasing helium fraction. In contrast, deviations from the AGA8-DC92 are within the 0.5% band. The experimental values were also used to calculate the second and the third virial coefficients, B(T,x) and C(T,x), as well as the second interaction virial coefficient B12(T) for this mixture.
The properties of the encapsulant are critical to the long-term performance of photovoltaic (PV) modules under the influence of sunlight including UV, elevated temperature, humidity and diffusion of oxygen. Encapsulation process represents a bout 40% of the whole PV module cost. The introduction of new non-EVA encapsulant material type "Low-Cost, High-Performance" should provide a solution to outdoor yellowing degradation problems. The emerging encapsulant materials exhibit a good compatibility with emerging PV solar cells for long term durability. This new generation of encapsulant materials has the advantage to improve e the PV module performances and long term durability for specific climate like desert regions. This scientific contribution presents an overview of the different encapsulant materials currently on the market, the general requirements of the emerging encapsulant materials and characterizations techniques for degradation, diagnostic and reliability lifetime estimation in the framework of Algerian renewable energy strategy.
Geogenic gases from natural sources, carbon dioxide (CO2) from a geological repository (carbon capture and storage - CCS) or a leaking gas pipeline can present serious risks in industrial and urban areas. To extend the lead time for risk treatment in such critical regions, reliable detection of gases within the shallow subsurface is required to observe critical gas accumulations before degassing into the atmosphere.
A near real-time monitoring approach is introduced to determine the volumetric expansion of a leakinggas in the subsurface. Considering the pressure relaxation with the ambient air pressure, the approach enables the forecasting of the final size of a pressurized gas body in terms of characteristic lengths. According to theoretical basics, such a characteristic length, which enables us to perform a gas (safety) measurement based on a purely geometrical measure, behaves independently of subsurface properties,i.e., it enables a reliable quantification of the escaping gas irrespective of its heterogeneous or changingflow path distribution. A field test for a 10 l/min pinhole leakage injected into a 10 m long, 0.4 m wide, 0.95 m deep soil-filled trench that was equipped with linear sensors shows the lateral-vertical volumetric gas expansion along these sensors, and demonstrates the applicability of the characteristic length approach.
Comparison of traceable methods for determining the calorific value of non-conventional fuel gases
(2016)
Energy-content measurements by direct methods (such as calorimetry) are used to validate the indirect method (from gas composition obtained by gas chromatography) which is generally adopted by grid operators for on-site gas control. A primary reference gas calorimeter and three field calorimeters were used for the first time to measure accurately the energy content of non-conventional gases (biogas and coal mine methane). The gas mixtures for this study were prepared by gravimetry and comprised three binary mixtures containing carbon dioxide and (up to 80 mol-%) methane, three ternary mixtures containing carbon dioxide, (up to 70 mol-%) methane and (up to 0.3 mol-%) hydrogen sulphide as well as a ten-component mixture with a methane content of approximately 64 mol-% which represents a typical coal mine methane. Associated uncertainty calculations were developed for each instrument and are presented here. Traceability of the measurements to the SI units is ensured in reference calorimetry, as calibration is accomplished by electrical simulation based on the Joule effect in order to obtain the heat capacity of the entire system. The results obtained with the four calorimeters are compared with each other and also with results calculated from the indirect method that is based on gas chromatography. Uncertainties (k = 2) between 0.07 and 0.49% for the reference gases were obtained with the reference calorimeter, while uncertainties for the field calorimeters range between 0.18 and 2.48% for the same mixtures. Compared to the usual standard deviation observed by gas chromatography for a multicomponent gas mixture of about 1%, it is demonstrated that the calorimetric method, although rarely used for non-conventional gases before, is appropriate for energy-content measurements of gases originating from renewable energy sources.
Gas cylinders made of composite materials receive growing popularity in light-weight applications. Current standards are mostly based on safety determination relying on minimum amounts of endured load cycles and a minimum burst pressure of a small number of specimens. This paper investigates the possibilities of a probabilistic strength assessment for safety improvements as well as cost and weight savings. The probabilistic assessment is based on destructive testing of small sized samples. The influence of sample size on uncertainty of the assessment is analysed. Furthermore, methods for the assessment of in-service ageing (degradation) are discussed and displayed in performance charts.
Concept for investigating mechanical and thermal impacts on distributed subsurface gas monitoring
(2016)
A multifunctional sensor in line shape was developed and introduced in previous work for measuring of gas concentrations, temperature change, and strain. A current field study focuses on a spatially distributed monitoring of subsurface CO 2 gas storage sites in near real time.
Mechanical impacts, e.g., caused by construction work, denudation, and seismic activity, can affect the integrity of underground gas storage sites. Thermal or moisture impacts, e.g., caused by weather conditions, can influence the gas Distribution behavior. In this paper, we briefly describe the setup of a CO 2 injection soil test field. This setup contains actuating elements for the investigation of mechanical and thermal impacts on distributed subsurface gas monitoring. A concept is given for evaluating these impacts and first experimental results are presented.
We have studied the mechanism of hydrogen storage in the aluminium based metal–organic framework CAU-1 or [Al4(OH)2 OCH3)4(O2C-C6H3NH2-CO2)3] using a complementary multidisciplinary approach of volumetric gas sorption analysis, in situ neutron diffraction and spectroscopy and ab initio calculations. The structure of CAU-1 forms two different types of microporous cages: (i) an octahedral cage with a diameter of about 10 Å and (ii) a tetrahedral cage with a diameter of about 5 Å. Though all metal sites of CAU-1 are fully coordinated, the material exhibits relatively high storage capacities, reaching 4 wt% at a temperature of 70 K. Our results reveal that hydrogen sorption is dominantly driven by cooperative guest–guest interactions and interactions between guest hydrogen molecules and organic linkers. The adsorption of hydrogen on the organic linkers leads to the contraction of the host framework structure and as a result to changes in the electronic potential surface inside the pores. This, in turn, leads to cooperative rearrangement of the molecules inside the pores and to the formation of additionally occupied positions, increasing hydrogen uptake. At the final stage we observe the formation of solid amorphous hydrogen inside the pores.
Matrimid and Matrimid/PhenethylPOSS nanocomposites films were prepared by solution casting. They can be considered as potential membrane materials for gas separation. Theire dielectric properties were investigated using Broadband Dielectric Spectroscopy (BDS) in combination with standard techniques. Matrimid shows one relaxation process assigned as beta*-relaxation and a conductivity contribution. The relaxation process has a high activation energy of 99 kJ/mol. Thus this process is supposed to be of cooperative nature due to a π-π stacking of the phenyl rings of Matrimid. The influence of the thermal history on Matrimid was analyzed with BDS as well where an annealing effect is found. The Matrimid/PhenethylPOSS nanocomposites show up to a concentration of about 4 wt% PhenethylPOSS a miscibility on a molecular level. For higher concentrations a phase separated structure was indicated. The conductivity of both systems is explained by π-π stacking of the phenyl rings which enhances charge transport.
Packages for intermediate level waste (ILW) often contain residual water besides the actual waste. The water either exists as obvious free water or it may be bound physically or chemically, e.g. as pore water. A water driven gas generation could occur by vaporisation and by radiolysis. Steam as the result of vaporisation causes an increasing pressure inside a package and can affect corrosion. Vaporisation and condensation processes itself change the thermal behavior of the content especially during strongly unsteady thermal situations like accident fire situations. Radiolysis changes the chemical composition of the content which could cause an unexpected interaction, e.g. hydrogen embrittlement. Besides the pressure build-up the radiolysis of water generates hydrogen and oxygen, which can be highly flammable respectively explosive. The gas generation caused by vaporisation and radiolysis must be taken into account during the design and the safety assessment of a package. Pressure build-up, a changed thermal behavior and content chemistry, and especially the risk of accumulation of combustible gases exceeding the limiting concentration for flammability has to be considered in the safety assessment. Approaches to ensure the transportability of stored packages due to radiolysis will be discussed.
The paper presents the first complex study of Gamma radiation effects on a low-loss perfluorinated polymer optical fiber (PF-POF) based on Cytop® polymer. Influence of gamma radiation on fiber’s optical, mechanical and climatic performance is investigated. The radiation-induced attenuation (RIA) in the visible and near-infrared region (0.4 μm-1.7 mm) is measured and its origins are discussed. Besides attenuation increase, radiation is also shown to decrease the thermal degradation stability of the fiber and to increase its susceptibility to water. With regard to complex fiber transmission performance upon irradiation, the optimal operation wavelength region of PF-POF-based systems intended for use in Radiation environments is determined to be around 1.1 μm. On the other hand, the investigated fiber holds potential for low-cost RIA-based optical fiber dosimetry applications with sensitivity as high as 260 dBm⁻¹/kGy in the visible region.