Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (59)
- Deutsch (24)
- Russisch (2)
- Italienisch (1)
- Mehrsprachig (1)
Referierte Publikation
- nein (87) (entfernen)
Schlagworte
- Laser beam welding (21)
- Solidification cracking (13)
- Hybrid laser arc welding (7)
- Laserstrahlschweißen (6)
- Additive manufacturing (5)
- Hot cracking test (5)
- Laser metal deposition (5)
- Critical strain (4)
- Elektromagnetische Schmelzbadunterstützung (4)
- Laser Metal Deposition (4)
- Laser welding (4)
- Laserhybridschweißen (4)
- Numerical simulation (4)
- Stainless Steel (4)
- Thick-walled steel (4)
- 316L (3)
- Additive Manufacturing (3)
- Electromagnetic weld pool support (3)
- Hybrid Laser Arc Welding (3)
- Hybrid laser-arc welding (3)
- Laser-Pulver-Auftragschweißen (3)
- Mechanical properties (3)
- Ti-6Al-4V (3)
- Weld pool shape (3)
- Additive Fertigung (2)
- CTW-Test (2)
- Charpy impact toughness (2)
- Cryogenic steel (2)
- Defokussierung (2)
- Edge effects (2)
- Endkrater (2)
- Ferromagnetischer Stahl (2)
- Heißrissresistenz (2)
- High power laser beam welding (2)
- Hot cracking (2)
- Hybrid welding (2)
- Inconel 718 (2)
- Laser beam Welding (2)
- Laser hybrid welding (2)
- Laser-Hybridschweißen (2)
- Local critical strain (2)
- Material transport (2)
- Melt pool dinamics (2)
- Microstructure (2)
- Optical flow (2)
- Partial penetration (2)
- Pipe manufacturing (2)
- Pipeline (2)
- Rundnaht (2)
- Single pass welding (2)
- Temperature behavior (2)
- Thermography (2)
- Weld defects (2)
- Weldability (2)
- laser welding (2)
- Überlappbereich (2)
- 3DDruck (1)
- 9%Ni steel, (1)
- Additiv (1)
- Aluminium (1)
- Analytical model (1)
- As-shielded arc welding (1)
- Aufbaustrategie (1)
- Austenitic stainless steels (1)
- Austenitische Stähle (1)
- Build - up Strategy (1)
- Bulging (1)
- Bulging effect (1)
- CFD-model (1)
- CO2 lasers (1)
- CTW test (1)
- Circumferential weld (1)
- Combined laser manufacturing (1)
- Contact element (1)
- Conventional Ni-based austenitic welding electrode (1)
- Corrosion (1)
- Critical strain rate (1)
- Cryogenic Steel (1)
- DIC technique (1)
- Dickblech (1)
- Different welding position (1)
- Digitale Bildkorrelationstechnik (1)
- Direct Laser Metal Deposition (1)
- Duplex (1)
- Duplex AISI 2205 (1)
- Duplex stainless steel (1)
- Duplex stainless steels (1)
- Duplex steels (1)
- Electromagnetic Weld Pool Support (1)
- Electromagnetic backing (1)
- Electromagnetic weld pool support system (1)
- Elektromagnetische Badstütze (1)
- Elektromagnetische Schmelzbadsicherung (1)
- Elektromagnetische Schmelzbadstütze (1)
- Element transport (1)
- End crater (1)
- Externally loaded test (1)
- FE-model (1)
- FEA (1)
- FEM (1)
- Ferritic welding electrode (1)
- Festigkeit (1)
- Filler material distribution (1)
- Fine-grained Steel (1)
- Flow pattern (1)
- Full Penetration (1)
- Gap bridgeability (1)
- Gas shielded arc welding (1)
- Hardness (1)
- Heißriss (1)
- Heißrissanfälligkeit (1)
- High power laser keyhole welding (1)
- High strength steel (1)
- High-power fibre laser (1)
- Hochfester Stahl (1)
- Hochleistungsschweißen (1)
- Hot crack (1)
- Hybrid-laser-arc welding (1)
- Hydrostatic and arc pressure exceed the Laplace pressure (1)
- In situ strain (1)
- Kaltzähe Stähle (1)
- Keyhole mode laser beam welding (1)
- Laser Beam Welding (1)
- Laser Metal Deposition (LMD) (1)
- Laser Metal Deposition; Laser Beam Welding; Duplex; Stainless Steel (1)
- Laser metal deposition (LMD) (1)
- Laser metal fusion (1)
- Laser-Pulver-Auftragschweißen (LPA) (1)
- Laser-Pulver-Auftragschweißen; Laserstrahlschweißen, Duplex, Pufferschichten (1)
- Laser-beam welding, (1)
- Laser-hybrid welding (1)
- Laserpulverauftragschweißen (1)
- Laserstrahl-(Hybrid)schweißen (1)
- Laserstrahl-MSG-Hybridschweißen (1)
- Liquid Metal Embrittlement (1)
- Lokale Effekte (1)
- Longitudinal weld (1)
- Low Temperature Toughness (1)
- Lötrissigkeit (1)
- MSG-Schweißen (1)
- Macro Processing (Joining, Welding) (1)
- Magnetic bath support (1)
- Magnetohydrodynamics (1)
- Magnettechnik (1)
- Manganese (1)
- Mechanical Properties (1)
- Misalignment of edges (1)
- Modellierung (1)
- Modified spray arc (1)
- Multi - physical modeling (1)
- Nickel (1)
- Nickel-based superalloy (1)
- Novel metrology (1)
- Novel optical measurement (1)
- Novel optical metrology (1)
- Numerical modelling (1)
- Numerical process simulation (1)
- Optical measurement (1)
- Optical measurement technique (1)
- Optical measurment technique (1)
- Optische Emissionsspektroskopie (OES) (1)
- Pendelstrategie (1)
- Penetration depth (1)
- Pipeline steel X120 (1)
- Plasma-cut samples (1)
- Preheating (1)
- ProMoAM (1)
- Process chain (1)
- Pufferschichten (1)
- Rissanfälligkeit (1)
- Rissbildung (1)
- SEP-1220-3 (1)
- SMAW (1)
- Schallemissionsanalyse (SEA) (1)
- Schweißeignung (1)
- Schweißen von kaltzähen Stählen (1)
- Schweißunregelmäßigkeiten (1)
- Self-restraint test (1)
- Shielding gases (1)
- Ship building (1)
- Single-pass welding (1)
- Solidification behaviour (1)
- Solidification craking (1)
- Spiralstrategie (1)
- Stainless steel (1)
- Strain measurement (1)
- Strain rate (1)
- Superelliptic Lamé curves (1)
- Temperaturentwicklung (1)
- Tensile strength (1)
- Thermal cycles (1)
- Thermo-fluid flow (1)
- Thermographie (1)
- Thick Materials (1)
- Thick plate welding (1)
- Thick plates (1)
- Thick-plate welding (1)
- Thick-walled Structures (1)
- Ti - 6Al - 4V (1)
- Turbine blade (1)
- Turbine industry (1)
- Untersuchung laserstrahlgeschweißter Verbindungen (1)
- V-notch impact toughness (1)
- Vakuum (1)
- Weld imperfections (1)
- Weld pool (1)
- Weld pool geometry (1)
- Weld pool shape approximation (1)
- Welding thermal cycle (1)
- Werkstofffragen (1)
- Werkstoffranking (1)
- Widerstandspressschweißen (1)
- Widerstandspunktschweißen (1)
- Windkraftanlagen (1)
- X8Ni9 (1)
- YAG lasers (1)
- cryogenic steel (1)
- hardness (1)
- hochfeste Stähle (1)
- laser hybrid welding (1)
- local effects (1)
- microstructure (1)
- tensile strength (1)
- thermal cycles (1)
- thick plate welding (1)
- vacuum (1)
- Ökonomische und ökologische Vorteile (1)
Organisationseinheit der BAM
- 9 Komponentensicherheit (57)
- 9.3 Schweißtechnische Fertigungsverfahren (55)
- 8 Zerstörungsfreie Prüfung (2)
- 8.0 Abteilungsleitung und andere (2)
- 9.0 Abteilungsleitung und andere (2)
- 1 Analytische Chemie; Referenzmaterialien (1)
- 1.9 Chemische und optische Sensorik (1)
- 8.1 Sensorik, mess- und prüftechnische Verfahren (1)
Eingeladener Vortrag
- nein (11)
Der Einsatz von Hochleistungswerkstoffen verlangt nach einer hohen Endformnähe der zu fertigenden Bauteile, um den Aufwand und somit die Kosten für Materialeinsatz und Nachbearbeitung möglichst gering zu halten. Der additive Einsatz in Form des Laser-Pulver-Auftragschweißens bietet hierfür durch den gezielten Materialauftrag ein hohes Potential. Herausforderungen bestehen in Bereichen der Vorhersagbarkeit und der Reproduzierbarkeit des Materialauftrages, sowie der Fertigungszeit. Unterschiedliche Einflüsse bei der Schichterzeugung führen dabei zu Abweichungen von der Soll-Geometrie. Die vorliegenden Untersuchungen behandeln den Einfluss von Spurgeometrie, Spurüberlappung, Verfahrweg und Aufbaureihenfolge auf die entstehende Bauteilform. Die Teilung einer Lage in Rand- und Kernbereich ermöglicht einen konturangepassten Verfahrweg und eine Erhöhung der Endformnähe innerhalb einer Ebene. Die Verwendung unterschiedlicher Spurgrößen bei der Bauteilerzeugung verdeutlicht die Möglichkeiten einer hohen Auftragsrate bei gleichzeitig hoher Formgenauigkeit. Bereits kleine Unterschiede beim Materialauftrag zwischen Kern- und Randbereichen, Start- und Endpunkten sowie in Bereichen des Richtungswechsels führen aufgrund von Fehlerfortpflanzung nachmehreren Lagen zu Abweichungen in der Aufbaurichtung. Kompensierungen mittels angepasster Baustrategien werden aufgezeigt und diskutiert. Die Nickelbasislegierung Inconel 718, die Titanlegierung Ti-6Al-4V sowie der austenitische Stahl 316L sind Bestandteil der vorliegenden Untersuchungen. Die gewonnenen Erkenntnisse verdeutlichen das Potenzial einer angepassten Aufbaustrategie zur reproduzierbaren Erzeugung von Bauteilen am Beispiel unterschiedlicher Körpergeometrien.
Heat treated 9%Ni steel is considered the most suitable and economic material for construction of large-size liquefied natural gas (LNG) storage tanks which operate at cryogenic temperatures (-196°C). Strength above 700 MPa as well as a minimum impact value of 60 J are required to ensure reliable operation of the LNG tanks at operating temperature. Conventional arc welding processes, including shielded metal arc welding, gas metal arc welding, gas tungsten arc welding and submerged arc welding, are currently used in construction of LNG tanks. Ni based filler wire is the preferred filler metal of choice in LNG tank construction. The main problem with this choice is the lower mechanical properties, particularly tensile strength of the weld metal. To compensate, the wall thickness needs to be excessively thick to ensure the strength of the welded structures. Ni based filler material is expensive and a large quantity is needed to fill the multi-pass weld grooves. These factors significantly add to the cost in the fabrication of LNG storage tanks. For these reasons, exploration of new welding technologies is a priority. A big potential can be seen in laser based welding techniques. Laser beam welding results in much smaller fusion zone with chemical composition and mechanical properties similar to that of the base material. Laser welding is a much faster process and allows for a joint geometry which requires less filler material and fewer welding passes. The advantages of laser welding can help to overcome the problems pointed out above. Trials of autogenous laser welding, laser cold-wire welding and hybrid laser-arc welding conducted on the 9%Ni steel are presented in this paper. Chemical composition of the weld metal as well as effects of welding parameters on the weld formation, microstructure and tensile strength is discussed. Filler wire penetration depth as well as character of its distribution in the narrow laser welds was examined using EPMA - electron probe microanalysis.
Laser welding is a widely established manufacturing process in many industry sectors. Solidification cracking represents one of the most inadequately solved problems in welding and has major economic implications. The avoidance of hot crack is for most fusion welding processes a key challenge for an important range of metallic construction materials and affects not only the manufacturers of welding equipment and material manufacturers, but also a large number of customers using welding technologies, as well as welding standardization and research. In this study a new investigation programme has been developed to qualify the hot cracking susceptibility of a variety of austenitic stainless steels. The results show the possibility of using this technique to determinate the critical values that occur with initiation of solidification cracking during laser beam welding
Solidification cracking phenomena taking place under Controlled Tensile Weldability (CTW) test conditions have already been investigated both experimentally and numerically via FEA in order to get a better understanding of the mechanisms of hot crack formation during laser beam welding of austenitic steel grades. This paper develops a three dimensional finite element model employing the contact elements technique to simulate the formation and propagation of solidification cracks during laser full penetration welding of fully austenitic stainless steel 1.4376. During the experimental procedure the resulting strain and displacement directed to the laser beam in the Close vicinity of the weld pool was measured at the surface of the workpiece using a Digital Image Correlation (DIC) technique with an external diode laser as an illuminating source. Local strain fields, global loads and crack lengths predicted by the model are in good Agreement with those observed in experiments.
Laser welding is a widely established manufacturing process in many industry sectors. Solidification cracking represents one of the most inadequately solved problems in welding and has major economic implications. The avoidance of hot crack forms for most fusion welding processes poses a key challenge for an important range of metallic construction materials and affects not only the manufacturers of welding equipment and material manufacturers, but also a large number of customers using welding technologies, as well as welding technical standardization and research. Solidification cracking susceptibility was examined with the help of the Controlled Tensile Weldability Test (CTW) developed by Federal Institute for Materials Research and Testing (BAM), Berlin. The test is based on the fact that hot crack formation depends on a critical strain that emerges within a critical temperature range, the so called brittle temperature range (BTR). Using this test and defined investigation programme a centreline solidification crack was generated. By controlling the applied strain during the laser beam welding process, it was possible to determine the critical strain and strain rate that led to solidification cracking formation. The hot cracking susceptibility of the tested stainless steels was qualified and quantified. The results demonstrate that the crack length increases with increasing applied strain. Furthermore, the strain rate has a significant influence on the formation of the solidification crack.
Impiego di un dispositivo per il vuoto locale di tipo mobile nell'applicazione del processo laser.
(2016)
Lo sviluppo del pennacchio di vapore durante la saldatura laser
di metalli con direzioni di propagazione lungo l'asse del
fascio laser comporta una riduzione della potenza del laser
assorbita nel keyhole. Questi effetti negativi possono essere
notevolmente attenuati mediante l'applicazione di una ridotta
pressione ambientale, diminuendo così l'interazione
tra il fascio laser ed i prodotti dell'evaporazione, condizione
che favorisce la stabilità del processo di saldatura e si traduce
in una maggiore profondità di penetrazione. Una tecnica
convenzionale utilizza il principio della camera a vuoto, simile
a quello utilizzato per la saldatura a fascio elettronico.
L'applicazione di questa tecnica è limitata dalle dimensioni
della camera e riduce quindi i vantaggi di questo approccio,
particolarmente per componenti di grandi dimensioni. Abbiamo
dimostrato la possibilità di applicazione del vuoto in
forma localizzata con apparecchiature mobili, che consentono
di generare una pressione ridotta solo in una piccola zona
attorno al keyhole. Utilizzando un dispositivo di chiusura
appositamente progettato per la pressione, di tipo mobile,
che può essere spostato lungo l'asse del giunto è possibile ottenere
una pressione assoluta di circa 200 mbar. Questo è
sufficiente per aumentare la profondità di penetrazione di
circa il 50%. I campioni di acciaio grado S355 sono stati
saldati con una potenza laser incrementale da 5 kW a 12
kW a pressione atmosferica e confrontati con quelli saldati
a pressione ambiente di 200 mbar. La valutazione della sezione
longitudinale ha rivelato un aumento della profondità
di penetrazione dei giunti di circa il 35%. Inoltre, sono stati
eseguiti test di saldatura in configurazione di giunti testa a
testa con lamiere di 15 mm di spessore con diverse potenze
associate al fascio laser eseguiti a pressione atmosferica ed
a pressione ambiente ridotta di circa 200 mbar. L'aumento
nella profondità di penetrazione fino al 40% è relativo alla
pressione ridotta. In particolare, basse velocità di saldatura
con pressione ridotta si sono rivelate particolarmente vantaggiose
in termini di aumento della penetrazione.
Full penetration high power bead-on-plate laser beam welding tests of up to 20 mm thick 2205 duplex steel plates were performed in PA position. A contactless inductive electromagnetic (EM) weld pool support system was used to prevent gravity drop-out of the melt. Welding experiments with 15 mm thick plates were carried out using IPG fiber laser YLR 20000 and Yb:YAG thin disk laser TruDisk 16002. The laser power needed to achieve a full penetration was found to be 10.9 and 8.56kW for welding velocity of 1.0 and 0.5 m min(-1), respectively. Reference welds without weld pool support demonstrate excessive root sag. The optimal value of the alternating current (AC) power needed to completely compensate the sagging on the root side was found to be approximate to 1.6 kW for both values of the welding velocity. The same EM weld pool support system was used in welding tests with 20 mm thick plates. The laser beam power (TRUMPF Yb:YAG thin disk laser TruDisk 16002) needed to reach a full penetration for 0.5 m min(-1) was found to be 13.9 kW. Full penetration welding without EM weld pool support is not possible-the surface tension cannot stop the gravity drop-out of the melt. The AC power needed to completely compensate the gravity was found to be 2 kW. (C) 2016 Laser Institute of America