Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Dokumenttyp
- Vortrag (3)
- Zeitschriftenartikel (1)
- Dissertation (1)
Schlagworte
- Multilayer (5) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (3)
Thermoelectric generators can be used for energy harvesting by directly transforming a temperature gradient into a voltage. Multilayer generators based on low-temperature co-fired ceramics technology (LTCC) are an interesting alternative to conventional π-type generators. They exhibit several advantages like high filling factor, possibility of texturing, co-firing of all materials in one single-step, and reduction of production costs due to the high possible degree of automation. Pressure-assisted sintering enables the theoretical possibility of co-firing two promising oxide thermoelectric materials: Ca3Co4O9 (p-type) and CaMnO3 (n-type). Due to the large difference in sintering temperature (300 K) the process is very challenging.
In this work we show the material development of Ca3Co4O9, CaMnO3, insulation and metallization for multilayer generators co-fired under pressure at 900 °C. The materials are tailored regarding their sintering behavior, electrical performance and coefficients of thermal expansion. Different generator designs (unileg and pn-type) were fabricated and analyzed regarding crack formation, interaction layers and thermoelectric performance. Simulated stresses during cooling in the multilayers are compared with actual crack formation for different sintering conditions. This study shows that a lower pressure level and a lower level of complexity are beneficial for co-firing and performance.
Thermoelectric materials can convert waste heat directly into electrical power by using the Seebeck effect. Calcium cobaltite Ca3Co4O9 is a promising p-type oxide thermoelectric material for applications between 600 °C and 900 °C in air. The properties and morphology of Ca3Co4O9 are strongly anisotropic because of its crystal structure of alternating layers of CoO2 and Ca2CoO3. By aligning the plate-like grains, the anisotropic properties can be assigned to the component. Pressure-assisted sintering (PAS), as known from large-scale production of low temperature co-fired ceramics, was used to sinter multilayers of Ca3Co4O9 green tape at 900 °C with different pressures and dwell times. In-situ shrinkage measurements, microstructural investigations and electric measurements were performed. Pressure-less sintered multilayers have a 2.5 times higher electrical conductivity at room temperature than dry pressed test bars with randomly oriented particles. The combination of tape casting and PAS induces a pronounced alignment of the anisotropic grains. Relative density increases from 57 % after free sintering for 24 h to 94 % after 2 h of PAS with 10 MPa axial load. By applying a uniaxial pressure of 10 MPa during sintering, the electrical conductivity (at 25°C) improves by a factor of 15 compared to test bars with randomly oriented particles. The high temperature thermoelectric properties show the same dependencies. The smaller the applied axial load, the lower the relative densities, and the lower the electrical conductivity. Longer dwell times may increase the density and the electrical conductivity significantly if the microstructure is less densified as in the case of a small axial load like 2 MPa. At higher applied pressures the dwell time has no significant influence on the thermoelectric properties. This study shows that PAS is a proper technique to produce dense Ca3Co4O9 panels with good thermoelectric properties similar to hot-pressed tablets, even in large-scale production.
Zur Messung der Sinterschwindung keramischer Folien und daraus aufgebauter Bauteile wurden an der BAM zwei Verfahren entwickelt. Beide Verfahren erlauben die Messung von Prüfkörpern mit praxisrelevanten Abmessung (200 mm x 200 mm) bzw. Realbauteilen bis 1000 °C. Die Hochtemperatur-Laserprofilometrie ist ein berührungsloses Verfahren und eignet sich besonders zur Bewertung der Schwindungsanisotropie und zur in-situ Charakterisierung von Verwölbung. Die Sinterpresse mit in-situ Dickenmessung ist sehr gut geeignet, um Schwindungsverhalten im Drucksinterprozess unter verschiedenen Atmosphären zu untersuchen. Der Aufbau beider Messsysteme wird erläutert und Anwendungsbeispiele mit wissenschaftlichem Hintergrund und direktem Industriebezug werden vorgestellt.
The sintering behavior of sub-micron Ni0.30Cu0.20Zn0.52Fe1.98O3.99 ferrite with and without Bi2O3 addition was studied. Ferrites with 0.5 wt% Bi2O3 exhibit enhanced shrinkage at T < 900 °C with significant grain growth. Additive-free ferrite powders also sinter to high density at 900 °C, however, grain growth is very limited. Both ferrites exhibit a permeability of µ = 400–450. Multilayers consisting of ferrite and low-k dielectric LTCC layers were prepared by co-firing at 900–915 °C. The shrinkage and thermal expansion characteristics of ferrite and LTCC tapes are similar. However, the permeability of integrated ferrite layers, made from ferrite tapes with Bi2O3 additive, significantly drops after co-firing with LTCC layers compared to separately fired monolithic ferrite multilayers. Contrarily, the permeability of integrated, Bi2O3-free ferrite layers, co-fired with dielectric tapes, is identical to that of monolithic ferrite multilayers. This finding is an important step toward ferrite integration into complex LTCC multilayer architectures.
Slip-rolling resistance of novel Zr(C,N) thin film coatings under high Hertzian contact pressures
(2010)
The present work was carried out within the framework of my four years activities as a scientific co-worker in the Working Group Tribological Optimization; Failure Analysis; Extreme Exposure in the division Tribology and Wear protection (VI.2) of the BAM Federal Institute for Materials Research and testing in Berlin, Germany and generously funded by the German Research Foundation (DFG WO521/6-1). First of all, I would like to express my sincere thanks to my supervisor Dr.-Ing. Mathias Woydt, head of the aforementioned working group, who gave me the opportunity to start my professional development, initiated and intensively supported this PhD work as well as accepted to take part in thesis committee. Prof. Dr. rer. nat. Walter Reimers, Chairman of the Institute for Materials Science and Technology of the Technical University of Berlin (TU Berlin), is also gratefully thanked for his interest in the thesis subject, for helpful comments and suggestions as well as for agreeing to participate in the referee of this work. I would like to thank also Prof. Dr.-Ing. Claudia Fleck, Chairman of the Material Engineering Department (Fachgebiet Werkstofftechnik) of the Technical University Berlin (TU Berlin), for assuming the chairmanship of the thesis committee. All the staff of the tribology division is also greatly acknowledged for bringing a pleasant working environment. Dr. Dirk Spaltmann is particularly thanked for the helpful discussions as well as for his assistance in English formulation. Dipl.-Ing. Manuel Reichelt and my bureau colleague Dr.-Ing. Géraldine Theiler will find here my many thanks for promoting constantly a good working atmosphere. Sigrid Binkowski and Dipl.-Ing. Norbert Kelling are also gratefully acknowledged for their constant and helpful technical support. André Otto is also thanked for his substantial administrative support. My sincere thanks go to Dr. rer. nat. (and “by the way” world and olympic champion in eights rowing) Ilona Dörfel (BAM V.1, Composition and Microstructure of Engineering Materials) for performing the highly relevant TEM investigations as also Heidemarie Rooch, and Ing. Wolfgang Gesatzke for the specific preparation of the samples. Furthermore, I greatly appreciate the contributions of Dr.-Ing. Vasile-Dan Hodoroaba, Birgid Strauß, Sigrid Benemann and Dipl.-Phys. Thomas Wirth (BAM VI.4) for their valuable contributions in microscopy analysis and to Dr.-Ing. Eric Wild (TU Berlin) for the substantial residual stress analysis of the coatings. Acknowledgement is also due to Dr. Thomas Chudoba from ASMEC GmbH for performing hardness measurements with his QCSM module. Thanks are surely extended to Fundación Tekniker, specifically Josu Goikoetxea and Dr. Javier Barriga for the manufacturing of the coatings in industrial deposition chambers and to the machining shop BAM Z.5 for the specimens preparation. Last, but by no means the least, I would like to thank all my friends for their support and to all the people who helped me directly or indirectly in my doctoral work and/or for my pleasant German adaptation. My very special thanks (du fond du coeur) go to my beloved parents Marie-Hélène (What is Tribology?) and Gérard (I miss you so much) and “of course” to my bright (and sometimes nerve-racking) sister Sophie, for everlasting encouragement and plenty of good advices in a wide range of domains. Ania, especially for your contribution in the decision of pursuing my “German experiment”.