Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Erscheinungsjahr
- 2017 (10) (entfernen)
Dokumenttyp
- Vortrag (10) (entfernen)
Sprache
- Englisch (10)
Referierte Publikation
- nein (10)
Schlagworte
- Friction (4)
- Cutting tools (3)
- Wear (3)
- Niobium carbide (2)
- Niobium carbide (NbC) (2)
- Tribofilms (2)
- 2Disk (1)
- 2Disk test (1)
- 2Disk test machine (1)
- Additive (1)
Eingeladener Vortrag
- nein (10)
The wear rates of self-mated alumina couples show that friction as well as wear is largely determined by the above mentioned hydro-thermal conditions. The presence of water and its amount available in the surrounding system either in liquid or in gaseous form plays a key role for friction and wear behavior and can be beneficial for the tribological profile of steam degradation resistant materials. Hot steam enhances the tribo-chemical formations of oxides and hydroxides on MgO-ZrO2, alumina and antimony impregnated carbon.
The slip-rolling 2Disk tribometer from Optimol Instruments represented the technological evolution in tribotesting of the well-known AMSLER-type tribometer marketed in 1922. Both use two discs with the same outer diameter rolling against each other on their circumference. In the AMSLER, the lower disc dips into an oil reservoir, whereas in the 2Disk the oil is injected into the contact. The oil supply of the 2Disk is controlled by pump and temperature by a heat exchanger.
The tribotesting categories have different scopes with associated "pros" and "cons" and results obtained in one category cannot be simply transferred to another. The impact of design overrules in general the influence of the metallurgy or materials choice. The "cheap" test methods aim pre-screening and assessment of basic properties as well as use mainly for the test specimens SAE E52100 (100Cr6, SUJ2) ball bearing steel and carbon steels. The main test geometries are ball-on-flat/(disk) or block-on-ring apart 4-ball geometry. The tribological test conditions. This enabled "dynamic" testing, where during a test the "critical" solicitations were repeatedly and freely passed.
The frictional response of molybdenum bis(C11-14 branched and linear alkyl) carbamodithioate oxo thioxo complex (Mo-dttc) versus bismuth dimethyldithiocarbamate (Bi-dtc) and bismuth dodecylbenzene Sulfonate (Bi-ddbsa) slip-rolling under mixed/boundary lubrication (T=120°C, n=10 millions of cycles, P0max=2.25 GPa) in PAO-based formulation against three different steel alloys were compared.
Niobium is today largely available. The initial NbC grade was substoichiometric, SPS sintered and cobalt bonded. The NiMo-bonded stoichiometric NbC1.0 grades enable the substitution of cobalt by nickel, SPS by conventional sintering and NbC0.88 by NbC1.0 in view of functional properties. Nickel bonded NbC grades have improved toughnesses versus cobalt NbC grades, but lose hardness. NiMo and NiMo2C bonded NbC1.0 grades compensated the loss in hardness while keeping the toughness.
The differences between the binary phase diagrams W-C and Nb-C illuminate several parameters for tailoring the properties of NbC. In the region of homogeneity of NbCx, with Nb4C3 and Nb6C5 other Niobium carbide phases occur. Properties, like micro-hardness, hot hardness, sliding wear, elastic modules and toughness can be tailored by the C/Nb Ratio, secondary carbides and the type of binder. Supporting results from different grades with varying C/Nb ratio or binder types will be illuminated. Thus, the NbC system offers to producers a wider parameter window, than WC.