Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Dokumenttyp
- Zeitschriftenartikel (41)
- Vortrag (10)
- Posterpräsentation (7)
- Beitrag zu einem Tagungsband (4)
- Dissertation (1)
Sprache
- Englisch (63)
Schlagworte
- Additive manufacturing (43)
- Residual stress (27)
- Computed tomography (14)
- Laser powder bed fusion (13)
- Ti-6Al-4V (12)
- Synchrotron X-ray diffraction (9)
- X-ray computed tomography (8)
- Neutron diffraction (6)
- Selective laser melting (6)
- Additive Manufacturing (4)
- Electron beam melting (3)
- IN718 (3)
- Diffraction elastic constants (2)
- Fatigue performance (2)
- MMC (2)
- Metal matrix composite (2)
- Process atmosphere (2)
- Residual Stress (2)
- Residual stress analysis (2)
- SLM (2)
- Synchrotron X-ray computed tomography (2)
- Ti-Nb alloy (2)
- X-ray diffraction (2)
- X-ray refraction (2)
- AISI 316L (1)
- Adhesives (1)
- Al alloy (1)
- Aluminum alloys (1)
- Anisotropy (1)
- Annealing treatment (1)
- As-built LPBF IN718 alloy (1)
- Binder Jetting (1)
- Biomaterials (1)
- Bitter technique (1)
- Computed Tomography (1)
- Contour scan strategy (1)
- Coordinate measurement machine (1)
- Crack propagation (1)
- Damage imaging (1)
- Deformation (1)
- Deviatoric (1)
- Diffraction (1)
- Diffraction-elastic constants (1)
- Distortion (1)
- Distortion upon baseplate removal (1)
- Effect of scanning strategies (1)
- Effective properties (1)
- Elastic constants (1)
- Electron beam (1)
- Electron beam powder bed fusion (1)
- Electron microscopy (1)
- Expanding cavity model (1)
- FEM (1)
- FEM Simulation (1)
- Fiber-reinforced composite (1)
- Functionally graded porous scaffolds (1)
- Gyroid lattice (1)
- HIP (1)
- Helium (1)
- Hot isostatic pressing (1)
- Hybrid manufacturing (1)
- Imaging (1)
- In situ alloying (1)
- In-situ neutron diffraction (1)
- In718 (1)
- Inconel 718 (1)
- Indentation (1)
- Intergranular strain (1)
- Intermetallics (1)
- Internal stress (1)
- Interphase residual stress (1)
- L-PBF IN718 material (1)
- LPBF (1)
- Laboratory X-ray diffraction (1)
- Laboratory energy-dispersive X-ray diffraction (EDXRD) (1)
- Laser Powder Bed Fusion (1)
- Laser beam melting (1)
- Laser methods (1)
- Laser-based additive manufacturing (1)
- Lattice structures (1)
- Lightweight structures (1)
- Load transfer (1)
- Macroscopic stress (1)
- Magnetic domain distribution (1)
- Mechanical behavior (1)
- Melt pool monitoring (1)
- Metal matrix composites (1)
- Micromechanical modeling (1)
- Micromechanics (1)
- Microstructure and texture (1)
- Multi-phase (1)
- Nanostructured powder (1)
- Near-surface X-ray diffraction (1)
- Neutron Diffraction (1)
- Neutron and X-ray diffraction (1)
- Nickel-based superalloys (1)
- Non-weldable superalloy (1)
- Nondestructive testing (NDT) (1)
- Online Process Monitoring (1)
- Orientation distribution (1)
- PBFLB/M AlSi10Mg alloy (1)
- Piston alloy (1)
- Porosity analysis (1)
- Powder analysis (1)
- Powder bed fusion (1)
- Powder bed fusion Laser beam (1)
- Powder methods (1)
- Residual Stresses (1)
- Residual powder removal (1)
- Residual stress in AM (1)
- Residual stress state (1)
- Residual stresses (1)
- Scaffold (1)
- Scan strategies (1)
- Scan strategy influence (1)
- Selective Laser Melting (1)
- Signal processing (1)
- Sintering (1)
- Solidification cracking (1)
- Strain-free lattice references (1)
- Strain-free lattice spacing (1)
- Strengthening mechanisms (1)
- Stress balance (1)
- Stress balance condition (1)
- Stress concentration tensor (1)
- Stress-relief heat-treatments (1)
- Surface roughness (1)
- Synchrotron X-ray CT (1)
- Synchrotron X-ray Refraction (1)
- Synchrotron X-ray diffraction (SXRD) (1)
- Synchrotron computed tomography (1)
- TPMS structures (1)
- Texture (1)
- Thermography (1)
- Ti6Al4V alloy (1)
- Tiatanium (1)
- Triply periodic minimal surfaces (1)
- Ultrasonic guided waves (UGWs) (1)
- VHCF (1)
- WAAM (1)
- Wear resistance (1)
- X-ray CT (1)
- X-ray Diffraction (1)
- X-ray analysis (1)
- X-ray and neutron diffraction (1)
- Yield strength (1)
- Zirconium (1)
Organisationseinheit der BAM
- 8.5 Röntgenbildgebung (63) (entfernen)
Eingeladener Vortrag
- nein (10)
Adhesively bonded composite joints can develop voids and porosity during fabrication, leading to stress concentration and a reduced load-carrying capacity. Hence, adhesive porosity analysis during the fabrication is crucial to ensure the required quality and reliability. Ultrasonic-guided wave (UGW)-based techniques without advanced signal processing often provide low-resolution imaging and can be ineffective for detecting small-size defects. This article proposes a damage imaging process for adhesive porosity analysis of bonded composite plates using UGWs measured by scanning laser Doppler vibrometer (LDV). To implement this approach, a piezoelectric transducer is mounted on the composite joint specimen to generate UGWs, which are measured over a densely sampled area. The signals obtained from the scan are processed using the proposed signal processing in different domains. Through the utilization of filter banks in frequency and wavenumber domains, along with the root-mean-square calculation of filtered signals, damage images of the adhesive region are obtained. It has been observed that different filters provide information related to different void sizes. Combining all the images reconstructed by filters, a final image is obtained which contains damages of various sizes. The images obtained by the proposed method are verified by radiography results and the porosity analysis is presented. The results indicate that the proposed methodology can detect the pores with the smallest detectable pore area of 2.41 mm^2, corresponding to a radius of 0.88 mm, with an overall tendency to overestimate the pore size by an average of 11%.
AbstractIn this study, we compare the residual stress state in a laser powder bed fusion (PBF‐LB/M) AlSi10Mg alloy in the as‐built (AB) condition with that after two different heat treatments (265 °C for 1 h, HT1; and 300 °C for 2 h, HT2). The bulk residual stress (RS) is determined using synchrotron X‐ray diffraction (SXRD), and near‐surface profiles are determined using laboratory energy‐dispersive X‐ray diffraction (EDXRD). The EDXRD results do not reveal any notable difference between the conditions at a depth of 350 μm, suggesting that the machining process yields a comparable residual stress state in the near‐surface regions. On the other hand, the SXRD results show that HT1 is more effective in relieving the bulk RS. It is observed that HT1 reduces the RS state in both the aluminium matrix and the silicon network. In addtion, HT2 does not have a significant impact on relaxing the RS as‐built state of the matrix, although it does induce a reduction in the RS magnitudes of the Si phase. It is concluded that the heat treatment stress relieving is effective as long as the Si‐network is not disaggregated.
Powder Bed Fusion – Laser Beam (PBF-LB) of high γ’ strengthened Ni-base superalloys, such as CM247LC, is of great interest for high temperature applications in gas turbines. However, PBF-LB of CM247LC is challenging due to the high cracking susceptibility during PBF-LB processing (solidification cracking) and heat treatment (strain age cracking, mostly caused by residual stresses). This study focuses on understanding the impact of process parameters on microstructure, residual stresses and solidification cracking. Laser power (P), speed (v) and hatch spacing (h) were varied while the layer thickness (t) was fixed. The melt pool size and shape were found to be key factors in minimizing solidification cracking. Narrower and shallower melt pools, achieved using a low line energy density (LED = P/v ≤ 0.1 J/mm), gave low crack densities (0.7 mm/mm2). A tight hatch spacing (h = 0.03 mm) resulted in reduced lack of fusion porosity. Electron backscatter diffraction investigations revealed that parameters giving finer microstructure with 〈100〉crystallographic texture had low crack densities provided they were processed with a low LED. Atom probe tomography elucidated early stages of spinodal decomposition in the as-built condition, where Cr and Al cluster separately. The extent of spinodal decomposition was found to be affected by the LED and the hatch spacing. Samples with low LED and small hatch spacing showed higher degrees of spinodal decomposition. X-ray diffraction residual stress investigations revealed that the residual stress is proportional to the volumetric energy density (VED = P/(v. h. t)). Although low residual stresses can be achieved by using low VED, there is a high risk of lack of fusion. Hence, other parameters such as modified scan strategy, build plate pre-heating and pulsed laser mode, must be further explored to minimize the residual stresses to reduce the strain age cracking susceptibility.
The overview of the activity of Federal Institute for Material Research and Testing (BAM, Belin, Germany) in the field material characterization by X-ray imaging is presented. The principle of X-ray Computed Tomography (XCT) is explained. The multiple examples of application of quantitative analysis by XCT are reported, such as additive manufacturing, Li-ion battery, concrete research.
Efficient density evolution during sintering of the as-printed component is vital to reach full densification and required properties of binder jet (BJT) components. However, due to the high porosity and brittle nature of the green compact, analysis of the microstructure development during sintering is very difficult, resulting in lack of understanding of the densification process. Density development from green state (57 ± 1.6 %) up to full density (99 ± 0.3 %) was characterized by high-resolution synchrotron X-Ray computed tomography (SXCT) on BJT 316L samples from ex-situ interrupted sintering tests. Periodicity of density fluctuations along the building direction was revealed for the first time and was related to the layer thickness of ~ 42 μm during printing that decreased down to ~ 33 μm during sintering. Sintering simulations, utilizing a continuum sintering model developed for BJT, allowed to replicate the density evolution during sintering with a mean error of 2 % and its fluctuation evolution from green (1.66 %) to sintered (0.56 %) state. Additionally, simulation of extreme particle size segregation (1 μm to 130 μm) suggested that non-optimized printing could lead to undesirable density fluctuation amplitude rapid increase (~10 %) during sintering. This might trigger the nucleation of defects (e.g., layer delamination, cracking, or excessive residual porosity) during the sintering process.
Large temperature gradients inherent to additive manufacturing (AM) processes induce large residual stress (RS) in the final part. Because RS can influence the tribological properties, this study focuses on the relationship between wear sliding properties and RS in IN718 coatings. Such coatings were deposited with a Laser metal deposition (LMD) machine using two different scanning strategies.
The wear resistance and RS state were investigated after surface milling. RS were measured before and after wear tests on a reciprocating sliding test apparatus.
Two different X-ray diffraction techniques were employed to measure the surface and subsurface state RS: Laboratory Energy Dispersive X-ray Diffraction (LEDXD) and Synchrotron X-ray Energy Dispersive Diffraction (SXEDD). Due to the milling process, the coatings show similar depth distributions of RS from 22 to 92 μm depth, but exhibit different magnitudes depending on the scanning strategy used. Reciprocating sliding wear tests induced high compressive residual stresses that erased the initial RS state, and a similar wear behavior was observed in the two samples. These samples possess similar texture and grain morphology. This demonstrates that the influence of RS on wear resistance is a second-order effect. Nevertheless, it was observed that RS can still impact the wear performance at the early testing stages of the repaired parts.
The overview of the activity of Federal Institute for Material Research and Testing (BAM, Belin, Germany) in the field of additively manufacturing material characterization will be presented. The research of our group is focused on the 3D imaging of AM materials by means of X-ray Computed Tomography at the lab and at synchrotron, and the residual stress characterization by diffraction (nondestructive technique). Also, two successful research project in collaboration with CAM2, Sweden are presented.
In the present study, in-situ observation of Hot Isostatic Pressure (HIP) procedure of laser powder bed fusion manufactured Ti-6Al-4V parts was performed to quantitatively estimate the densifcation rate of the material and the infuence of the defect initial size and shape on such rate. The observations were performed in-situ using the Ultrafast Tomography Paris-Edinburgh Cell and the combination of fast phase-contrast synchrotron X-ray tomography and energy dispersive difraction. With this strategy, we could quantify how the efectiveness of HIP depends on the characteristics of a defect. Smaller defects showed a higher densifcation rate, while the defect shape did not have signifcant efect on such rate.
Hot Isostatic Pressing (HIP) is often introduced to tackle the porosity issue in additively manufactured (AM) materials. For instance, HIP post-processing is recommended to improve fatigue resistance of Laser powder bed fusion (PBF-LB) manufactured parts [1, 2]. Even though HIP cannot completely remove porosity, it significantly decreases the defect population and its average size below the critical threshold value leading to early crack initiation.
In the present study, in-situ investigation of HIP procedure of PBF-LB Ti-6Al-4V parts was carried out to gain further insights into the densification mechanism occurring during HIP. The in-situ observations at high pressure and high temperature are uniquely possible at the PSICHE beamline of the Soleil synchrotron (France), thanks to the Ultrafast Tomography on a Paris-Edinburgh Cell (UToPEC) and the combination of the fast phase-contrast tomography and energy-dispersive diffraction [3, 4]. A detailed methodology was developed to ensure that the correct pressure and temperature were maintained during the experiments.
The results allowed an estimation of the global dentification rate during HIP of PBF-LB Ti-Al-4V material, as well as a detailed quantitative characterization of the influence of pore size and shape on the densification process, thereby understanding the effectiveness of HIP process on different pore categories. After 20 mins, 75% of porosity can be considered as closed or has size below the resolution of the XCT reconstruction. We also observed that the smallest defects showed higher densification rate, while the defect shape did not have significant effect on such rate. The current development of in-situ HIP experiment allows experimental quantification and validation of the simulation work. Ultimately it paves the road to tailoring the HIP procedure for different materials depending on the porosity and microstructure.
The focus of the presentation focus will be on 3D imaging by means of X-ray Computed Tomography (XCT) at the lab and at synchrotron, and the non-destructive residual stress (RS) characterization by diffraction of additively manufactured (AM) materials in BAM (Berlin, Germany). The manufacturing defects and high RS are inherent of AM techniques and affect structural integrity of the components. Using XCT the defects size and shape distribution as well as geometrical deviations can be characterized, allowing the further optimization of the manufacturing process. Diffraction-based RS analysis methods using neutron and synchrotron X-rays at large scale facilities offer the possibility to non-destructively spatially resolve both surface and bulk RS in complex components and track their changes following applied thermal or mechanical loads.