Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Dokumenttyp
- Zeitschriftenartikel (119) (entfernen)
Schlagworte
- Additive manufacturing (16)
- Residual stresses (13)
- Residual stress (12)
- Welding (12)
- High-strength steels (9)
- Cyclic R-curve (7)
- Fatigue crack propagation threshold (7)
- Fatigue (6)
- Fracture mechanics (6)
- Microstructure (6)
- Ultrasonic-assisted milling (6)
- Additive Manufacturing (5)
- Creep-resistant steel (5)
- High-strength steel (5)
- Hydrogen (5)
- Fatigue crack growth (4)
- Fatigue strength (4)
- GMA welding (4)
- Neutron diffraction (4)
- Process parameters (4)
- Stress relief cracking (4)
- Surface integrity (4)
- TIG welding (4)
- Alloy 36 (3)
- Crack closure (3)
- Defects (3)
- Diffusible hydrogen (3)
- Heat treatment (3)
- Kitagawa-Takahashi diagram (3)
- LIBS (3)
- Laser powder bed fusion (3)
- Neutron imaging (3)
- Post weld heat treatment (3)
- Restraint (3)
- Weldments (3)
- Alloy modification (2)
- Austenite-to-martensite transformation (2)
- Bragg-edge imaging (2)
- Carrier gas hot extraction (2)
- Chemical composition (2)
- Cold cracking (2)
- Component assessment (2)
- Constraint (2)
- Damage tolerance (2)
- Debye–Waller factor (2)
- Digital image correlation (2)
- Duplex stainless steel (2)
- Endurance limit (2)
- Fatigue crack propagation (2)
- Fatigue limit (2)
- Fracture (2)
- Fracture resistance (2)
- Gas tungsten arc welding (GTAW) (2)
- Heat control (2)
- Heat-affected zone (2)
- High entropy alloy (2)
- High strength steel (2)
- Hot cracking (2)
- Hydrogen assisted cracking (2)
- Hydrogen-assisted cracking (2)
- IN718 (2)
- Implant test (2)
- In situ measurement (2)
- L-PBF (2)
- LTT weld filler materials (2)
- Low transformation temperature (LTT) steel (2)
- Mechanical Engineering (2)
- Mechanical properties (2)
- Mechanics of Materials (2)
- Metals and Alloys (2)
- Microstructure and texture (2)
- Neutron radiography (2)
- Non-metallic inclusions (2)
- Plasma-transferred arc welding (2)
- Pores (2)
- Repair-welding (2)
- Residual Stress (2)
- Residual stress analysis (2)
- S-N curve (2)
- Selective laser melting (2)
- Short cracks (2)
- Small-scale specimens (2)
- Steel (2)
- Submerged arc welding (2)
- Varestraint testing (2)
- Wasserstoff (2)
- Welded joints (2)
- Welding residual stresses (2)
- Wärmeführung (2)
- μCT-analysis (2)
- 2101 duplex stainless steel (1)
- 316L (1)
- 3D Scanning (1)
- ADXRD (1)
- AGIL (1)
- AISI 316L (1)
- AISI D2 (1)
- AM 316L stainless steel (1)
- ASTM E647 (1)
- Additive Fertigung (1)
- Aging (1)
- AlSi10Mg (1)
- AlSi10Mg alloy (1)
- Alternative test procedure (1)
- Aluminum alloys (1)
- As-built LPBF IN718 alloy (1)
- Austenitic (1)
- Austenitic stainless steels (1)
- Backlight (1)
- Bainitischer Schmiedestahl (1)
- Bauteilauslegung (1)
- Bayesian technique (1)
- Betriebsfestigkeit (1)
- Bragg-edge neutron 2D imaging (BENI) (1)
- Brazil nut Mesocarp (1)
- Bruchmechanik (1)
- Burst (1)
- CCT diagrams (1)
- Chapetti’s and IBESS model (1)
- Characterisation (1)
- Co-Cr-alloy (1)
- Cobalt-chromium alloy (1)
- Codes and standards (1)
- Cold cracking safety (1)
- Component test (1)
- Component-like test (1)
- Computed Tomography (1)
- Computed tomography (1)
- Contact fatigue (1)
- Cooling rate (1)
- Coordinate measurement machine (1)
- Corrosion pits (1)
- Crack arrest (1)
- Crack closure effect (1)
- Crack closure mechanisms (1)
- Crack-tip constraint (1)
- Cracking (1)
- Creep resistant steel (1)
- Crown-abutment connection (1)
- Crystal plasticity (1)
- Crystallographic texture (1)
- Crystallographic texture control (1)
- Cutting forces (1)
- Cutting tool (1)
- Cyclic J-integral (1)
- Cyclic R-curve analysis (1)
- Cyclic loading (1)
- Cyclic stress-strain curve (1)
- DED-arc (1)
- Data evaluation methods (1)
- Debye-Waller-Faktor (1)
- Dental materials (1)
- Diffraction-elastic constants (1)
- Diffusion (1)
- Dilatometry (1)
- Dislocation density (1)
- Dissimilar metal weld (1)
- Distortion (1)
- Distortion upon baseplate removal (1)
- Ditigtal image correlation (1)
- Dynamic load (1)
- EA4T steel (1)
- EDS (1)
- Effect of scanning strategies (1)
- Eigenspannungen (1)
- Elastic follow-up (1)
- Elastic-plastic fracture mechanics (1)
- Electron backscatter diffraction (EBSD) (1)
- Electron backscattered diffraction (1)
- Electron microscopy (1)
- Energetic reference parameter (1)
- Environment (1)
- Environmental conditions (1)
- Environmental effect (1)
- Environmental effects (1)
- Evaporation (1)
- Experimental design (1)
- Experimental determination (1)
- Experimental procedure (1)
- FAT class (1)
- FAT class approach (1)
- Fail-safe design (1)
- Fatigue Strength (1)
- Fatigue crack initiation (1)
- Fatigue crack propagation stages (1)
- Fatigue life (1)
- Fatigue loading (1)
- Fatigue propagation threshold (1)
- Fatigue properties (1)
- Fatigue strength and life (1)
- Finite element (FE) (1)
- Finite element analysis (1)
- Flaw assessment procedures (1)
- Flaw interaction (1)
- Fractography (1)
- Fracture Mechanics (1)
- Fracture assessment (1)
- GMAW (1)
- GMAwelding (1)
- Gas metal arc welding (1)
- Global stability criterion (1)
- Graphite modules (1)
- HCF (1)
- Hastelloy X (1)
- Heat affected zone (1)
- High strength steels (1)
- High-entropy alloys (1)
- High-strength steel filler metal (1)
- High-strength structural steel (1)
- Hochfeste Feinkornbaustähle (1)
- Hochfester Stahl (1)
- Hot tensile test (1)
- Hydrogen diffusion (1)
- Hydrogen embrittlement (1)
- Hydrogen measurement (1)
- IBESS (1)
- IBESS Approach (1)
- IBESS model for short cracks (1)
- IN718 PBF-LB/M (1)
- IN725 (1)
- ISO 12108 (1)
- ISO 3690 (1)
- Impact damage (1)
- Implant-supported prostheses (1)
- Implants (1)
- In situ (1)
- In-situ Process Monitoring (1)
- Inclusion cluster (1)
- Inclusion size (1)
- Inclusions (1)
- Intrinsic fatigue propagation threshold (1)
- Kaltrisse (1)
- Kitagawa-Takahashi (K-T) diagram (1)
- L-PBF IN718 material (1)
- LCF (1)
- LCF region (1)
- LIBS TIG welding (1)
- LPBF (1)
- LTT Weld Filler Materials (1)
- LTT filler metal (1)
- Laboratory X-ray diffraction (1)
- Large-scale test (1)
- Laser Powder Bed Fusion (1)
- Laser beam melting (LBM) (1)
- Laser implantation (1)
- Laser-based additive manufacturing (1)
- Legierungsmodifikation (1)
- Life prediction (1)
- Lifetime (1)
- Local Weld Geometry (1)
- Localized laser dispersing (1)
- Low transformation temperature (1)
- Low transformation temperature filler materials (1)
- L‐PBF (1)
- MAG welding (1)
- MVT (1)
- Machining (1)
- Margin design (1)
- Material defects (1)
- Measurement (1)
- Mechanical anisotropy (1)
- Medium entropy alloy (1)
- Metal additive manufacturing (MAM) (1)
- Metallschutzgasschweißen (1)
- Micro-shrinkages (1)
- Microalloyed steels (1)
- Microcracking (1)
- Microfocus X-ray computer tomography (μCT) (1)
- Minimum Waiting Time (1)
- Mis-match (1)
- Misfit (1)
- Modification of structural morphology (1)
- Monotonic and cyclic crack driving force (1)
- Multi-pass welding (1)
- Multiple crack initiation (1)
- Multiple crack propagation (1)
- Multiple cracking (1)
- Multiple cracks (1)
- Nahtgeometrie (1)
- Near-surface X-ray diffraction (1)
- Near-threshold regime (1)
- Neutron Diffraction (1)
- Neutron and X-ray diffraction (1)
- Ni alloy (1)
- Nickel-based superalloys (1)
- Niobium carbide (1)
- Non-destructive Materials (1)
- Non-sharp defects (1)
- Nuclear reactor systems (1)
- Oberflächenintegrität (1)
- Offshore (1)
- Offshore steel grade (1)
- Offshore steels (1)
- Online Process Monitoring (1)
- Oxide-induced crack closure (1)
- Peak stress method (1)
- Peak stress method (PSM) (1)
- Phase transformation (1)
- Photogrammetry (1)
- Post-weld heat treatment (1)
- Principal stress (1)
- Probabilistic assessment (1)
- Process development (1)
- Projekt AGIL - Alterung additiv gefertigter metallischer Materialien und Komponenten (1)
- Prostheses (1)
- R-curve analysis (1)
- Reference standards (1)
- Refraction (1)
- Repair welding (1)
- Residual stress in AM (1)
- Residual stress state (1)
- Retained Austenite (1)
- Rissbildung (1)
- Roughness (1)
- S-N probabilistic field (1)
- S-Phase (1)
- SLM (1)
- Safety (1)
- Sample random results (1)
- Scan strategies (1)
- Scan strategy influence (1)
- Scattering (1)
- Schutzgasschweißen (1)
- Scratches (1)
- Secondary stresses (1)
- Selective laser melting (SLM) (1)
- Short crack propagation (1)
- Shrinkages (1)
- Sicherheit (1)
- Software (1)
- Solidification cracking (1)
- Stainless Steel (1)
- Stainless steels (1)
- Staircase method (1)
- Standardisation (1)
- Static load (1)
- Statistics (1)
- Stiffness (1)
- Stochastic sample functions (1)
- Strain-free lattice references (1)
- Strain-free lattice spacing (1)
- Strength mismatch (1)
- Stress balance (1)
- Stress balance condition (1)
- Supermartensitic steel (1)
- Support configurations (1)
- Surface preparation (1)
- Surface roughness (1)
- Surface texturing (1)
- Synchrotron X-ray diffraction (1)
- Synchrotron diffraction (1)
- Synchrotron radiation (1)
- TEKKEN (1)
- TIG (1)
- Tensile properties (1)
- Testing parameters (1)
- Thermal conductivity device (1)
- Thermal desorption analysis (1)
- Thermography (1)
- Thick-walled (1)
- TiB2 (1)
- TiC (1)
- TiN (1)
- Tool wear (1)
- Toughening mechanisms (1)
- Toughness (1)
- Turbine disk (1)
- Ultraschallunterstütztes Fräsen (1)
- Varestraint test (1)
- WAAM (1)
- WAAM Ti-6Al-4V (1)
- Weld geometry (1)
- Weld metal cracking (1)
- Weld toe geometry (1)
- Welded Joints (1)
- Welded joint (1)
- Wind Energy (1)
- Wind energy (1)
- X-ray Diffraction (1)
- X-ray and Neutron Diffraction (1)
- X-ray and neutron diffraction (1)
- X-ray diffraction (1)
- X-ray refraction (1)
- XRF (1)
- contour method (1)
- neutron diffraction (1)
- residual stress analysis (1)
Organisationseinheit der BAM
- 9.4 Integrität von Schweißverbindungen (119) (entfernen)
Paper des Monats
- ja (4)
For the hydrogen-based energy economy of tomorrow, the construction of the necessary infrastructure will play a central role. Most materials used to date, such as welded steels, can be prone to hydrogen embrittlement under certain conditions. This includes the classic delayed cold cracking during welding as well as degradation phenomena during service of components in hydrogen-containing environment. For the evaluation of any hydrogen effect, for example, on the mechanical properties of a welded metallic material, the hydrogen content must be precisely determined. In the case of weld seams, the carrier gas hot extraction (CGHE) according to ISO 3690 is meanwhile state-of-the-art. CGHE is based on accelerated hydrogen degassing due to the thermal activation of hydrogen at elevated temperatures. In addition to the quantification of hydrogen, thermal desorption analysis (TDA) with varying heating rates can be used to determine and evaluate the hydrogen trapping at microstructural defects in the material. For both techniques, experimental and metrological influences must be considered, which have a major effect on the result. For example, ISO 3690 suggests different sample geometries and minimum extraction times for CGHE. This study summarizes the results and experiences of numerous investigations at the Federal Institute for Materials Research and Testing (BAM) with different sample temperatures and geometries (ISO 3690 type B and cylindrical TDA samples) regarding the influence of the sample surface (polished/welded), measurement accuracy depending on the sample volume and the insufficient monitoring of the effect of PI control on the extraction temperature. A deviating extraction temperature from the target temperature can significantly falsify the measurement results. Based on the results, methods are shown which allow the desired extraction temperature to be reached quickly without physically interfering with the measuring equipment. This serves to significantly improve the reliability of the hydrogen measurement through increased signal stability and accelerated hydrogen desorption. In general, an independent temperature measurement with dummy samples is recommended for the heating procedure of choice to exclude possible undesired temperature influences before the measurement. The methods described can be transferred directly to industrial applications
Stresses in repair welding of high-strength steels—part 2: heat control and stress optimization
(2024)
In welding of high-strength steels, e.g. for foundations and erection structures of wind energy plants, unacceptable defects can occasionally be found in the weld area, which should be removed by thermal gouging and subsequent re-welding. High shrinkage restraint of repair welds may lead to crack formation and component failure, predominantly in interaction with degraded microstructures and mechanical properties due to repair cycles. This study aims for elaboration of recommendations for repair concepts appropriate to the stresses and materials involved to avoid cold cracking, damage and expensive reworking. In part 1 [1] of this study, systematic investigations of influences of shrinkage restraint on residual stresses and cold cracking risk during repair welding of two high-strength steels S500MLO for offshore application and S960QL for mobile crane structures were focussed. In this part 2, the microstructure, particularly hardness, and residual stresses due to gouging and influences of heat control parameters in repair welding are analysed. A clear reduction in residual stress after gouging can be observed, especially for the specimens with restrained transverse shrinkage. Gouging to a depth of approx. 2/3 of the seam height does not lead to a complete relaxation of the observed reaction forces. Particularly for the higher strength steel S960QL, there are pronounced areas influenced by the gouging process in which a degradation of the microstructure and properties should be assumed. Overall, the repair welds show a significant increase in the width of the weld and HAZ compared to the original weld, especially in the case of S960QL/G89. The repair welds show higher welding-induced stresses than the original welds, especially in the areas of the HAZ and the base metal close to the weld seam. This behaviour can be attributed overall to increased restraint conditions due to the remaining root weld or shorter gouge grooves. In good agreement with earlier investigations, the residual stresses transverse to the weld can be significantly reduced by upwardly limited working or interpass temperatures, and the reaction stresses resulting from high restraint conditions can be effectively counteracted. The influence of the heat input on the stress formation is low compared to the interpass temperature for both test materials.
Multiple principal element alloys encompass the well-known high entropy alloys (HEA). The alloy system represents a new class of materials consisting of at least three alloying elements, each containing 5 to 35 at.%. Thus, this alloying concept differs fundamentally from conventional materials such as steel or nickel alloys. For this purpose, the alloying elements are specifically selected, the microstructures are adjusted in a single-phase and, in some cases, multi-phase manner. In particular, conflicting goals, such as the trade-off between strength and ductility in conventional steels, are overcome. However, in the last 20 years, the focus has been on material synthesis. With the increase in available material quantities, the focus is now on processing issues such as joining and welding processes. The weldability of HEAs has received very little attention so far. The experience with dissimilar metal welds is completely lacking but is essential for the application of these materials in combination with conventional materials. The present study presents comprehensive experimental results on the weldability of an equimolar CoCrFeMnNi-HEA in cold-rolled and heat-treated condition, which was joined by tungsten inert gas welding to an austenitic steel AISI 304. The mechanical properties of the dissimilar metal welds were characterized by cross-weld tensile samples, whereas the local deformation in the weld of the different welding zones was measured by digital image correlation. In accordance with the respective initial HEA condition (cold-rolled vs. heat-treated), the local strain behavior was divergent and influenced the global mechanical properties of both DMW types. Nonetheless, the experiments provided proof in principle of the weldability for dissimilar joints of the CoCrFeMnNi-HEA welded to conventional materials like austenitic stainless steels ensuring a corresponding capability for mechanical loading. This allows further considerations on the application of these innovative materials.
AbstractThe sustainable and resource-efficient production of wind energy plants requires the use of modern high-strength fine-grain structural steels. This applies to both foundation and erection structures, like mobile or ship cranes. During the assembly of steel structures, unacceptable defects can occasionally be found in the weld area. In most cases, the economical solution would be local thermal gouging of the affected areas and re-welding. Due to the high shrinkage restraint of the joint groove in the overall structure, the superposition of global and local welding-induced stresses may lead to crack formation and component failure, particularly in interaction with the degradation of the microstructure and mechanical properties of high-strength steels during the repair process. However, manufacturers hardly have any information about these issues and there is a lack of recommendations and guidelines to take these safety-relevant aspects into account in adequate repair concepts. The aim of this research is to derive recommendations for repair concepts appropriate to the stresses and materials involved providing a basis for standards and guidelines to avoid cold cracking, damage and expensive reworking especially for high-strength steels. Part 1 of this study involves systematic investigations of influences of shrinkage restraint during repair welding of two high-strength steels S500MLO for offshore application and S960QL for mobile crane structures. The quantification of the shrinkage restraint of repair weld joints was achieved by means of experimental and numerical restraint intensity analysis. In welding experiments with self-restrained slot specimens, restraint intensity and introduction of hydrogen via the welding arc using anti spatter spray were varied systematically to analyse the effect on welding result, residual stresses and cold cracking. It could be shown that increasing restraint intensities result in significantly higher transverse residual stress levels. In the case of hydrogen introduction S500MLO showed no cold cracking independent of the restraint conditions. However, S960QL was found to be considerably cold cracking sensitive if hydrogen is introduced. With increasing restraint intensity length and number of cold cracks increases significantly. Part 2 [1] of this study is focussed on microstructure and residual stresses due to gouging and stress optimization via adequate heat control parameters in repair welding.
Die additive Fertigung mittels Schweißverfahren bietet große ökonomische Vorteile für eine ressourceneffiziente Bauteilherstellung. Offene Fragen bezüglich Homogenität, Anisotropie der Schweißgefüge und den damit verbundenen Bauteileigenschaften stehen einer wirtschaftlichen Verarbeitung oftmals im Wege. Finale Bauteilgeometrie und Oberflächengüte erfordern meist komplementäre subtraktive Fertigungsschritte. Werkstoffe für hochbelastbare Komponenten sind oftmals schwer spanbar. In einem Vorhaben der BAM und des ISAF wurde untersucht, wie die Modifikation der AM-Schweißzusätze und das ultraschallunterstützte Fräsen (US) die Zerspanungssituation verbessern. Der vorliegende Artikel stellt wesentliche Zusammenhänge zwischen Legierung, Gefüge und Zerspanung zweier schwer spanbarer Hochleistungslegierungen (FeNi und CoCr) dar. Großes Potenzial zeigte neben dem US die Modifikation mit Zr und Hf bei Zulegierung in das Schweißgut mittels Beschichtung von Massivdrähten bzw. Herstellung von Fülldrähten.
Die neue Generation von bainitischen Schmiedestählen bietet auf der einen Seite ein erhebliches Festigkeitspotenzial, das es im Sinne des Leichtbaus auch für zyklisch belastete Sicherheitsbauteile zu heben gilt. Auf der anderen Seite geht mit dieser Festigkeitssteigerung im Vergleich zu Vergütungsstählen ein Verlust an Duktilität und Zähigkeit einher. Am Beispiel des Demonstratorbauteils Achsschenkel ging das Forschungsvorhaben der Frage nach, wie ein Freigabeprozess zu gestalten ist, damit das Festigkeitspotenzial der neuen Stähle zuverlässig ausgenutzt werden kann. Als Ergebnis wird eine Vorgehensweise dargestellt, die den Eigenschaften der neuen Generation von Schmiedestählen Rechnung trägt, um den sicheren Betrieb der Komponenten zu gewährleisten.
High-strength steels offer potential for weight optimization due to reduced wall thicknesses in modern constructions. Additive manufacturing processes such as Wire Arc Additive Manufacturing (WAAM) enable the resource-efficient production of structures. In the case of defects occurring in weld seams orWAAM components due to unstable process conditions, the economical solution is local gouging or machining and repair welding. It is important to understand the effects of machining steps on the multiaxial stress state in conjunction with the design-related shrinkage restraints. Research into how welding and slot milling of welds andWAAM structures affects residual stresses is still lacking. For this reason, component-related investigations with high-strength steels with yield strengths ≥790 MPa are carried out in our research. In-situ digital image correlation (DIC) and ex-situ X-ray diffraction (XRD) were used to analyze the stresses and strains induced on specimens during and after milling. The systematic analyses revealed a significant interaction of the stiffness and microstructure of the specimens with the initial residual stresses induced by welding. Subsequent repair welds can result in significantly higher residual stresses.
The new multi-element alloying concept of systems with defined entropy (HEA — high-entropy alloy or MEA — medium-entropy alloy) is increasing in material research interest. Improved properties or combinations of properties are shown by several systems. Thus, the resulting microstructures and production of HEA/MEA as well as properties have been primarily investigated so far. Furthermore, processing is a key issue to transfer HEA/MEA systems to real components. Since welding is the most important joining process for metals, it is crucial to investigate the influence of welding to guarantee component integrity. Since most HEA are made of expensive alloying elements such as Co or Ni, they will not be used entirely as structural materials. Thus, it can be advantageous to weld conventional alloys such as austenitic stainless steels with the HEA and MEA to produce components that are both application-oriented and economically viable. Therefore, in this paper, first results of dissimilar metal welding, by tungsten inert gas (TIG) and friction stir welding (FSW), of a CoCrFeMnNi HEA as well as a CoCrNi MEA with a conventional AISI 304 austenitic stainless steel are presented. The focus is on the microstructure formation due to the two welding processes. The results of TIG welding show a dendritic microstructure, whereas in FSW both materials are stirred but still coexist.
Offshore wind turbines continuously increase in size and weight and demand adequate offshore foundations concepts like monopiles, tripods, or jackets. These components are typically constructed using submerged arc welding (SAW) with high-strength thick steel plates like the S420ML. During welding, the occurrence of delayed hydrogen-assisted cracking (HAC) must be anticipated. HAC is a critical combination of the local hydrogen concentration within a susceptible microstructure under certain mechanical load, i.e., the occurring (welding) residual stresses. The welding sequence of the thick-walled plates complicates the residual stress distribution due to the necessary repeated thermal cycling, i.e., welding seam/layer deposition to fill the joint. For that purpose, SAW with two-wire-technique was used to weld a specially designed and prototype-like mock-up of a real component with a thickness of 50 mm, filled with over 20 passes and a seam length of 1000 mm. Additional welded stiffeners simulated the effect of a high restraint, to achieve critical HAC conditions. The necessity of a minimum waiting time (MWT) before the NDT can be conducted (to exclude HAC) was critically verified by the application of ultrasonic testing of the welded joint at different time-steps of the NDT of up to 48 h after the completion welding. The residual stresses were determined by a robot XRD goniometer. Tensile residual stresses up to the yield limit are found both in the weld metal and in the heat-affected zone. Numerical modeling allowed the qualitative estimation of the hydrogen diffusion in the weld. No noticeable HAC occurrence was identified and confirms the high cracking resistance of the investigated material. Finally, the applicability of the MWT concept should be critically discussed.
This study was carried out to investigate the neutron transmission signal as a function of sample temperature during a welding process. A theoretical description that includes the Debye-Waller factor was used to describe the temperature influence on the neutron crosssections. Neutron imaging using a monochromatic beam helps to observe transmission variations related to the material temperature. In-situ neutron imaging of welding experiments show the distribution of the temperature in bulk steel samples. The performed finite element modelling of expected temperature distributions shows good agreement with the obtained experimental data.