Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Dokumenttyp
- Vortrag (5)
Sprache
- Englisch (5)
Referierte Publikation
- nein (5)
Schlagworte
- Rheology (5) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (5) (entfernen)
While today, engineers can choose from a wide range of rheology modifying admixtures, in some parts of the world, these are difficult to access, due to their complex processing. However, alternatives can be bio-based polymers such as polysaccharides from various sources. These are easily accessible all over the world, do not demand for complicated processing, and typically they are more sustainable than many established materials, which are crude oil-based.
The paper presents the effects of acacia gum, cassava starch and the gum of triumfetta pendrata A. Rich on the rheological performance of cementitious systems. It is shown that acacia gum can be as efficient as polycarboxylate based superplasticisers, cassava starch can reduce the yield stress slightly with little effect on the plastic viscosity, and the gum of triumfetta pendrata A. Rich increases the thixotropy of cement pastes with plasticizing polymers significantly.
In the last years flowable concrete has become increasingly important in applications such as, for systems with highly reinforced concrete with a complicated formwork, or sprayed concrete and 3D-printing of concrete. For all these applications it is necessary to have tailored rheological properties. Rheology can be described by values of yield stress and plastic viscosity, which can be determined for example by evaluation of rheometer measurements. But for different materials various rheometers with different geometries and stirrers are being used. To see the effects from paste in concrete, it is necessary to investigate mixes of paste, mortar and concrete, stepwise. But currently there exists no device, which is calibrated for these different systems at once. Due to this fact, conventional tests such as V-funnel efflux-time and flow diameter were determined, as well as rheometer data in different cell sizes and geometries.
In this study the assessment of rheological effects in the binder on the rheology of mortar was investigated by using combination of two rheometers.
Hydrous silicate and borate glasses of up to 8 wt% water were prepared using wet condition of melting under external pressure. Rheological experiments were conducted to determine the effect of the total water content on viscous flow and kinetic fragility. The findings indicate that dissolved water acts as a strong fluxing agent in both glass types. Water decreases particularly viscosity at the glass transition range, makes the viscosity-temperature curve "longer" and thus decreases kinetic fragility. Recent IR and NMR data are presented to link the dynamics of hydrous silicate and borate glasses with their structure particularly with regard to changes in the water-, silicon- and boron-speciation.
The repair of earthen structures is not an easy task. Earth as a construction material has comparatively weak mechanical properties. It is also susceptible towards liquid water, were it can lose cohesion very quickly if certain moisture contents are exceeded. Repair concepts of structures built with such materials are therefore challenging. Historical earthen structures often exhibit damages in form of extensive cracking, which may have been caused by static or dynamic loads. Frequently these cracks are insufficiently or inappropriately repaired because of lack of knowledge and / or technology. In particular, the behaviour of crack repair by grouting poses a challenge in earthen materials and demands specific requirements for the grouting mortar, such as low water content, good water retention, low shrinkage. Grouting materials require additional specifications such as compatible strengths and Young’s modulus as well as good adhesion to the earthen substrates. In addition, grouts have to be sufficiently flowable to fill small cracks and voids without segregation or bleeding. Therefore, the rheological behaviour has to be well understood and controlled to gain the desired effects.The repair of cracks in earthen buildings is traditionally done by stuffing manually mortar into the gap. Naturally, this method is only usable for cracks with large widths. Another disadvantage is that cracks going through thicker walls cannot be completely reached by the tools used for stuffing the mortar into the crack. Lime based grouts for earthen materials were usually used for re-attachment of plasters but less for structural reasons.Due to the nature of earthen materials grouts based on formulated or hydraulic lime (according to the definition in EN 459-1) have to meet considerable demands on a variety of properties, which are related to compatibility, durability and in particular to the ability of being injected. The goal of this study was to create a grout, which can be used to re-establish structural continuity in cracked earthen masonry or other massive earth walls (rammed earth and cob) with the focus on grouting cracks. The grout material was based on hydrated lime (calcium hydroxide) with additions of pozzolana and lime stone filler.
In the last decades, numerical simulations of fresh concrete flow have gained importance in concrete industry. They showed a potential to become a tool for prediction of concrete casting and to help engineers to avoid expensive mistakes on site. A promising field for application of numerical modelling is casting of Self-Compacting Concrete (SCC), since the main area of application of SCC are complex and highly-reinforced building elements. Simulations of fresh concrete flow involve complex mathematical models and time-consuming computations. In case of casting simulations, the simulation time is additionally significantly increased because each reinforcement bar occurring in succession has to be considered one by one. This is particularly problematic in case of SCC casting, since this type of concrete is typically used for heavily-reinforced structural members. With the aim to decrease simulation time and to come closer to a practical simulation tool, we proposed an innovative modelling approach that models a zone with arrays of the reinforcement bars as a porous medium (PM). By defining characteristic parameters of the PM, its influence on the flow can be defined. This approach simplifies the geometry to be modelled and significantly decreases the computational time. The present contribution provides a brief description the proposed numerical model and of the conducted validation studies. The applicability of the model on fresh concrete is verified through the comparison between experimental measurements and numerical simulations.